Search Documents

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined in part for the sgstem Gd-Fe. Seven intermetallic compounds have been found at compositions corresponding to the following Gd-Fe ratios; 2:3, 1.2, 1:3, 2:7, 1:4, 1:5, and 2:17. The GdFe, com-pound has a congruent melting point above 18000C, whereas all of the remaining compounds melt incongruently, A eutectic exists at 13 wt pct Fe at a temperature of 860°C. ALTHOUGH an increasing amount of information is becoming available on the metallurgy of pure rare earth metals, relatively few studies have been made on alloy systems of the rare earths with the transition metals; iron, nickel, and cobalt. Even less data are extant on gadolinium alloys although it could be expected that such alloys might possess interesting structural and magnetic properties. In this paper, we report investigation of the gadolinium-iron alloy system. Studies on systems containing nickel and cobalt will be presented in subsequent papers. Previous data on gadolinium-iron compounds have been reported by Endter and Klemm1 and Jep-son and Duwez.2 Both reports agree on the existence of the GdFe2 phase, which crystallizes with the C-15type structure (face-centered cubic). This is in accord with results of the present work. EXPERIMENTAL The gadolinium metal used was prepared by met-allothermic reduction of high purity gadolinium fluoride. A typical analysis of the metal thus produced indicated the principal impurities to be oxygen, 0.24 pct, and tantalum, 0.2 pct. The iron metal used for alloying was a reagent grade material. Alloys were prepared by arc melting mixtures of the respective metals. Appropriate quantities of the two component metals were carefully weighed, blended and compacted. The compacts were then melted in an arc furnace consisting of a water-cooled copper hearth plate and a water-cooled tungsten-tipped counter electrode contained in a brass vacuum chamber. The furnace was evacuated to an absolute pressure of less than 1 with the leak rate established as being less than 20 per min. The furnace was then back-filled to a pressure of 25 mm of Hg, with a 75 pct He-25 pct Ar mixture. Arc melting at 25 v and 300 amp was maintained for about 30 to 60 sec until the entire visible area of the sample became molten, by which time surface tension had drawn the molten metal pool into a large bead. After allowing the furnace to cool, the alloy button was inverted and the melting process repeated. A series of melts was made covering entire composition ranges from 100 pct Gd to 100 pct Fe. All samples were examined metallographically in the as-melted condition. As the phase diagram became rationalized, and differential thermal analysis had given indications of temperature arrests, annealing was carried out in vacuo or in argon. Generally, compositions containing more than about 60 pct Gd were heat treated at 750°C and alloys containing less than this quantity of gadolinium were annealed at 1000°C. Prolonged annealing times were of the order of 100 to 200 hr. Metallographic examination was repeated on the annealed materials. Although little material loss was noted during alloy preparation, chemical analyses were made on all specimens prepared. The following standard, analytical techniques were used. Samples were dissolved in hydrochloric acid; insoluble material was filtered off, ignited and fused with potassium pyro-sulfate. The cold melt was leached with dilute acid and the solution thus obtained added to the main sample solution. Gadolinium was always determined gravimetri-callv as oxide from oxalate ignition. Iron was removed from an aliquot sample by electrolysis on a mercury cathode at approximately six volts. Gadolinium in the iron-free electrolyte was then precipitated as oxalate which was subsequently ignited to oxide. Iron was determined volumetrically in an aliquot solution by reduction with stannous chloride fol-

Jan 1, 1962

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined for the system gadolinium-nickel. Nine intermetallic compounds have been found at compositions corresponding to the following gadolinium-nickel ratios: 3:1, 3:2, 1:1, 1:2, 1:3, 2:7, 1:4, 1:5, 2:17. The GdNi and GdNi5 compounds have congruent melting points of 1300' and 1500°C, respectively while the remaining compounds melt in-congruently. Eutectics exist at 15 wt pct Ni, 31 1/2 wt pct Ni and 87 wt pct Ni with melting points of 6703 8803 and 1220°C, respectively. IN a continuing investigation of the properties of rare earth alloys, a study has been made of the gadolinium-nickel system. Previous work encompassed the iron containing alloys and a subsequent paper will deal with the constitution of the gadolinium-cobalt system. Vogel,1 examined alloys of nickel with lanthanum and cerium. R3Ni, RNi, RNi2, RNi3, RNi4, and RNi5 compounds were found. Endter and Klemm,2 Fulling et al.3 Heumann,4 and Nowotny5 found the 1:2 compositions of this series to exist in a C-15 (face-centered cubic) structure, and the 1:5 compositions in a hexagonal system. Jepson and Duwez6 more recently examined these 1:2 and 1:5 compositions and generally confirmed earlier data while Wernick and Geller7 most recently have given additional data on the GdNi5 compound. Comparisons with our results will be made in the appropriate section of this report. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been given in our earlier paper.8 Chemical analyses of the alloy samples were made by dissolving the specimen in nitric acid, precipitating the gadolinium as hydroxide and the nickel with dimethylglyoxime. Both precipitates were ignited to oxide and weighed. RESULTS Microstructure— Metallography of alloy specimens in this series has been conducted on both arc-melted and annealed materials. Etchants used have been 5 pct nital with approximately 10 pct distilled water added, for high gadolinium samples; Carapella's ferric chloride solution for intermediate compositions; and Marble's (copper sulfate) reagent for high nickel content alloys. Because of difficulties encountered in the grinding and polishing of specimens containing 40 to 75 wt pct Ni, no photomicrographs were made of such specimens. The microstructure of an arc-melted 5.3 wt pct Ni alloy is shown in Fig. 1. Light etching primary grains of gadolinium are embedded in an eutectic matrix. The microstructure of an alloy of 9.55 wt pct Ni alloy, Fig. 2, annealed 50 hr at 700°C, consists almost entirely of the intermetallic compound Gd3Ni. The structure of an arc metal alloy of approximately 19 pct Ni, Fig. 3, consists of grains of the compound GdNi embedded in the Gd3Ni2-Gd3Ni eutectic. The arc-cast structure of the 38.7 wt pct Ni alloy is shown in Fig. 4. Large primary grains of a compound rest in a matrix structure of coarse GdNi-GdNiz eutectic. Because of the occurrence of several peritectic compounds in the central region of the diagram, identification of the primary structure in this alloy is not certain. As has been indicated above, microstructures of alloy specimens containing between ca 40 and 75 wt pct Ni have not been photographed. These specimens were highly brittle, and macro- and micro-cracking were impossible to control in the grinding and polishing procedures. Prolonged annealing did not alleviate this condition. Visual observations in small specimens did, however, provide evidence for a multiplicity of phases and peritectic dissociations of compounds although rationalization of structures was not possible.

Jan 1, 1962

By A. A. Bauer

The ?-to-? transformation has been studied in zirconium alloys containing 22 to 70 wt pct U. In this range of compositions the ? phase can be retained by quenching. Transformation to ? occurs by a nucleation-and-growth process. The diffusion of atoms to preferred lattice sites to yield a partially ordered structure apparently controls the rate of reaction. Alpha uranium and a zirconium precipitate from the supersaturated E phase initially formed in alloys outside the equilibrium E phase composition limits. ZIRCONIUM-Uranium alloys have long been of interest for reactor-fuel applications because of the low thermal-neutron cross section of zirconium. Considerable information is available on the various properties and behavior of these alloys1 although there had been a number of areas where information was incomplete. As part of a program to provide more detailed knowledge in these areas, the presently reported investigation was undertaken. The constitutional diagram of the zirconium-uranium system is shown in Fig. 1.' The system is distinguished by a region of complete solid solubility between the body-centered cubic ß-zirconium and ? uranium phases and the existence of an intermediate phase in the vicinity of 50 wt pct U. This intermediate phase, designated as E, is reported3 to have a primitive hexagonal structure with a = 5.03 and c = 3.08A. The structure is partially ordered with zirconium atoms at the 0, 0, 0 position and zirconium and uranium atoms located randomly at the 1/3, 2/3, 1/2, and 2/3, 1/3, 1/2 positions. While the E phase may be nominally designated as of UZr2 stoichio-metry, the random distribution of uranium and zirconium atoms permit a considerable range in composition. Of interest in the research performed were alloys in the range from 20 wt pct (10 at. pct) to 70 wt pct (47 at. pct) U. In this range of compositions the body-centered-cubic ? phase can be retained either completely or partially on quenching. The nature and kinetics of transformation of the ? phase were the subject of study. Proceeding concurrently with the presently reported work was an investigation by Kearns4 which has since been reported. Kearns studied alloys containing 50 to 60 wt pct U prepared from sponge zirconium. While the work reported here is for alloys prepared from crystal-bar zirconium and the techniques of study are to some extent dissimilar to those employed by Kearns, general agreement so far as results and interpretation can be reported. Experimental Techniques—Alloys were prepared and the transformation of the ? phase studied during interrupted-quench and quench-and-temper isothermal heat treatments by means of hardness measurements and X-ray diffraction and metallographic techniques. The isothermal transformation of the ? phase on quenching and tempering was investigated further employing dynamic-modulus measurements. Electrical resistivity and limited Hall coefficient measurements were also obtained as part of the study. Alloy Preparation and Heat Treatment— Alloys containing 15, 20, 22, 30, 40, 45, 50, 55, 60, and 70 wt pct U were prepared from as-reduced uranium and crystal-bar zirconium. The alloys were double arc melted by consumable-electrode are-melting techniques. The final ingots were forged and rolled at temperatures between 790" and 840oC to 1/4-in. rod and 1/8-in. sheet. Chemical analyses of the fabricated alloys were

Jan 1, 1961

By W. A. Tiller, J. P. McHugh

THE phase diagram of the Ge-Te system was first investigated by Klemm and Frischmuth.' They arrived at the phase diagram shown in Fig. 1 indicating the presence of a peritectic phase boundary at the 50 at. pct Ge composition. Later, Schubert and Fricke2 obtained data which suggested to them the possible existence of a eutectic at about 55 at. pct Ge. In order to resolve these differences, we have carefully studied this system in the region 40 to 60 at. pct Ge using both the conventional thermal analysis technique and a new solidification technique.3y4 The alloys were prepared from semiconductor grade germanium and 99.999+ Te by reacting the elements in evacuated, graphite coated, vycor tubes. The samples were placed in a thermal analysis apparatus described elsewhere4 and cooling curves were taken of each alloy to determine the liquidus surface. The cooling curve for a 50 at. pct alloy shows two distinct arrests about 1°C apart which

Jan 1, 1961

By S. Weinig, J. Winter

The grain boundary adsorption of solutes as a function of bulk concentration and solution temperature was studied using internal-frictimz techniques. From the variation of the cor-responding energy of activation for the Phenomenon, the inter-actior2 energy between a solute atom and a high-angle boundary was calculated. Interaction energies in the range of 0.3 ev were obtained, and were used to obtain the actual concentration of solute at the grain boundary. In corroboralory creel, studies the direct grain boundary contribution to the total creep strain was measured. It was found that the interface creep varied with the type and magnitude of the solute adsorbed. Subscribing to the theory of their being energetically favorable sites at the grain boundary for solutes of both Positive and negative size deviations, ternaries were investigated in Which solutes of both types were present. A marked increase in the resistance to grain boundary creep was manifested. THE major difficulty which has been encountered in investigations of the grain boundary segregation of solutes has been the lack of a sufficiently sensitive method of measuring the amount of adsorbed solute at the boundary. For the general case of a high-angle boundary, no direct method of measuring the adsorption at the boundary has been found to date. Internal friction has been used in several studies of grain boundary adsorption1-3 and although it is somewhat indirect, it was demonstrated to have the necessary sensitivity. In this investigation the authors have used internal-friction techniques in conjunction with a study of the grain boundary contribution to the total creep strain. As both parts of the investigation were performed on the same specimens it was possible to combine a highly sensitive technique with a somewhat more direct method in order to obtain information about the adsorption phenomenon. From internal-friction studies the rate of increase of the activation energy was observed to be a function of the difference in size between the solute and solvent atoms. It was proposed that if Gibbs' adsorption isotherm is considered, i.e., where r is the excess solute at the boundary, c is the bulk concentration, and ay/ac is the change in grain boundary energy with bulk concentration, then AH b/ac must vary in the same way as ay/ac and therefore In this way a relative measure of the grain boundary adsorption of solutes is directly obtainable from in-ternal-friction studies. If the previous work in the field of grain boundary adsorption of solutes is examined, certain apparent information is desirable if the phenomenon is to be understood. The most important questions that must be asked are as follows: 1) Is the adsorption of solutes at the grain boundary an equilibrium process? 2) Can the Mott model of the grain boundary be used as a basis of setting up an elastic interaction between the grain boundary and solute atoms? 3) Is it possible to obtain an exact measure of the excess solute at the grain boundary as a function of temperature and bulk concentration rather than merely a relative measure of the adsorption 4) Are the conclusions obtained from an indirect method such as internal-friction studies meaningful in considering gross grain boundary effects such as creep? EXPERIMENTAL PROCEDURE The material used in this investigation was Bureau of Mines "superpurity" titanium (79 Bhn—1500 kg

Jan 1, 1960

By C. J. Osborn

The temperature dependence of the free energies of formation of metallurgically important oxides, sulphides, chlorides, carbonates and sulphates is presented graphically, whereby the task of deriving practical metallurgical information is greatly simplified. The diagrams have been revised according to the latest available thermodynamic data. WHILE it is true that much careful investiga-tional work remains to be done, there are already available in the literature sufficient thermo-dynamic data to enable the metallurgist to predict with reasonable confidence the equilibrium conditions to be expected in most important, and potentially important, metallurgical reactions. In this connection, the careful, critical compilations of K. K. Kelley and his collaborators in numerous U. S. Bureau of Mines Bulletins are particularly valuable. However, the translation of reliable thermo-dynamic data into metallurgical language unfortunately involves lengthy manipulations of the cumbersome formulas which can be set up from heat of formation, entropy, and heat capacity data. Many years ago, Kelley20 predicted that thermo-dynamic calculations would be made in the future "with the aid of free energy, heat content, and entropy tables, rather than by means of the algebraic methods employed at present", and where such tables are available they greatly simplify the task of deriving practical metallurgical information. However, in addition to these tables, there are also available one or two reliable graphical presentations, particularly of free energy data, which may be used in the same way as the tables, but which have the added advantages that interpolation is never necessary, and that the behavior of different metals or compounds may be compared at a glance. Some years ago Professor Robert Lepsoe, Head of the Department of Metallurgy at Norways Institute of Technology (N.T.H.), began a compilation of curves showing the temperature dependence of the heat contents of the elements, and the heat contents and heats and free energies of formation of the common metallurgical compounds. With such a compilation, the thermal and free energy requirements of a reaction may be read from curves in a matter of seconds; and this statement applies not only to the formation of compounds from their elements, and to the reverse dissociation, but to any reaction involving substances whose thermodynamic properties are available. This follows from the fact that heats and free energies of formation are completely additive. For example, the free energy change associated with the chlorination of a metallic oxide at any temperature, T, is given by the free energy of formation of the chloride at temperature T minus that of the oxide also at T; both of these quantities may be read directly from curves of the type suggested above. Since this early, unpublished work of Lepsoe, both Ellingham7 and Richardson and Jeffes46 have

Jan 1, 1951

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

By R. W. Heckel

The growth and shrinkage rates of second-phase particles of various size distributions are analyzed in terms of five mathematical models. These models apply to various forms of diffusion-controlled growth (one model) and interjace-controlled growth (four models). The expression for diffusion-controlled growth assumes local equilibrium at the interface between the second Phase and the matrix and through the choice of the proper flux area perrnits the definition of minimum diffusion-controlled growth kinetics. The interface-controlled kinetics models consider the situations where the rate-controlling step occurs at either the interlace undergoing solution or the interface undergoing deposition. In addition, each of these interface-controlled kinetics models is analyzed for interface reaction rates which are independent of the thermodynamic activity gradient across the interface or proportional to the gradient. THE variation of the size distribution of second-phase particles in a solute-saturated matrix has been a stimulating topic for many years. Research has been carried out in this area for situations where the matrix was either liquid or solid. It is well-understood that the over-all process results in an increase in the average particle size, a decrease in the total number of particles per unit volume, and a net decrease in surface area. Greenwood1 has presented a mathematical model based upon the mass balance existing between growing and shrinking particles. His analysis is stated in terms of Fick's First Law using concentration gradients set up between particles of different size as a result of the effect of surface curvature on solubility. Greenwood's analysis indicates that the mean particle size should increase approximately as the cube root of time. Asimow2 has shown that several of the simplifying assumptions employed by Greenwood may be eliminated from this diffusion-controlled model with little increase in complexity. Lifshits and Slyozov3-5 have also considered the growth-shrinkage problem involving diffusion-controlled kinetics. Their analysis was extended to include the effects of interacting particles ("kinetic approximation"), particle shape, and elastic strains. These authors also show that the mean particle size varies as the cube root of the reaction time. wagner6 has formulated expressions for both diffusion-controlled kinetics and interface-controlled kinetics in the growth-shrinkage problem. Wagner's diffusion-controlled kinetics is based upon the same form of mass balance using Fick's First Law as used by others and is shown to be applicable to situations where kr >> D (k is the interface reaction constant, r is the particle radius, and D is the diffusion coefficient). This analysis also yields a mean particle size which varies as the cube root of time, in agreement with other workers. Wagner also developed interface-controlled kinetics to handle kr « D. This model was based upon the fact that the interface reaction rate is proportional to the interface area. Wagner assumed that the rate was also proportional to the thermodynamic activity difference, ?a, existing across the interface. Thus, the specific reaction rate at the surface of radius r was defined as k • 4nr2 . ?a. It is the purpose of the present paper to reconsider the processes of diffusion-controlled growth and interface-controlled growth in the variation of particle-size distributions as a function of time at constant second-phase volume. The analyses are formulated in a manner which permits data obtained

Jan 1, 1965

By R. W. Heckel, R. L. DeGregorio

The DeHoff method of determining the size distribution of ellipsoid-shaped, second-phase particles has been applied to the spheroidization of cementite in a eutectoid steel. The surface area of Precipitates determined from the various size fractions in the distribution was correlated with surface-area measurements based on the number of intersected interfaces on a random lest line. The precipitate particles were found to be oblate ellipsoids with an axial ratio of about 0.90. The size distributions were found to be log-normal. A method is proposed whereby the shrinkage of small particles and growth of large ones can be determined from the experimental data. The experimental data are compared to previously proposed mathematical models describing diffusion-controlled kinetics and various types of interface-controlled kinetics. The experimental growth and shrinkage rates are considerably slower than those predicted by diffusion-controlled kinetics. The best fit is obtained for a model describing interface-controlled kinetics limited by the rate of formation of cementite at the growing interfaces where the interfacial reaction rate is proportional to the solute thermodynamic activity gradient across the surface. THE subject of spheroidization of second-phase particles has been considered previously by other investigators. Livingston1 has studied the precipitation of the cobalt-rich phase from copper alloys containing 0.7 to 3.2 wt pet Co. His results indicate that the average particle size increases as the cube root of the heat treatment time in accord with diffusion-controlled kinetics.'-' Komatsu and rant' in their studies of the growth of SiO2 in a dispersion-strengthened copper-silica alloy found that the initial growth of SiO2 proceeded by diffusion-controlled growth and later stages were limited by interface-controlled growth. The values of the activation energy obtained for the interface- controlled process led them to the conclusion that the process was limited by the dissociation of SiO2 at the shrinking interface. The transition from diffusion-controlled growth to interface-controlled growth was characterized by a particle size which varied with the heat-treatment temperature. It is also interesting to note that the particle-size distribution as found by Komatsu and Grant exhibits log-normal behavior when replotted on log-probability coordinates. Dromsky, Lenel, and Ansell9 have observed the growth of Al2O3 particles having a mean free path of about 1.5 to 13 µ. Their photomicrographs indicate that the Al2O3 particle sizes were larger than those observed by Komatsu and Grant. Dromsky, Lenel, and Ansell concluded that the Al2O3 coarsened by an interface-controlled growth mechanism limited by the solution of A12O3 at the shrinking interfaces. Bannyh, Modin, and Modin10 have studied the spheroidization of a eutectoid steel (0.83 wt pet C). Their spheroidization (tempering) treatments were carried out in the range from 210o to 700°C for times between 1.5 sec and 20 hr. Measurements of mean particle size as a function of time indicated a cube root of time dependence of size at 700°C, in agreement with previous analyses of diffusion-controlled kinetics.2°7 At lower temperatures, the time dependence was less than the one-third power. It is important to note that, although mathematical models of growth* considering particle-size distribution have been available, measurements of only mean particle size have been carried out. DeHoff11 has presented a quantitative metallography technique which is applicable to the determination of the size distribution of ellipsoids of constant shape. This method is applicable to both oblate and prolate ellipsoids of all ratios of minor to major axis and is based upon an extension of Saltykov's analysis12 of the distribution of spheres of varying size. DeHoff's analysis is based upon measurements of the minor axis of the particles on a random plane of polish in a unit area. This method provides a measure of the number of ellipsoids in various size ranges per unit area. As pointed out by DeHoff, such measurements may be used to obtain surface area and total precipitate volume data. Thus, the accuracy of the distribution analysis may be checked by comparison of the surface and volume

Jan 1, 1965

By A. E. Nehrenberg

THE mechanism by which austenite forms in steels has received a great deal of attention in the literature in past years.'-'* Our present knowledge concerning this mechanism has been recently summarized quite concisely by Bain and Vilella,1 while a few years ago the literature was carefully reviewed by Roberts and Mehl.² The consensus is that any ferrite-carbide interface is a potential site for the nucleation of austenite during heating above the Acl temperature, and that the new austenite generally grows freely to produce approximately equiaxed grains, whether the carbides are initially present in the lamellar or the spheroidal form. In the case of eutectoid steels, growth of the new grains of austenite continues until contact is established with other grains. Then growth stops and an initial austenite grain size is established which does not change until the heating is continued to some high temperature at which grain coarsening begins. In the case of pearlitic steels which are not of eutectoid composition, the proeutectoid ferrite or carbide may interfere with the growth of the austenite if the temperature is not above that designated the A63 or the Acm, respectively. Although a large amount of work has been done to establish the mechanism of austenite formation in steels, it became clear to the present author while he was studying the transformation characteristics of a new 0.25 C Mn-Si-Ni-Mo hypoeutectoid steel" that the manner in which austenite grows in steels depends upon some factor, or factors, not previously considered. This was indicated by the fact that when this steel in the spheroidized condition was heated above the Ae1 temperature the new austenite which was formed did not envelop the carbides and grow in an equiaxed manner as described by Bain³ or spheroidized steels. Instead, in this steel, the austenite was observed to grow much more readily in certain directions than in others with the result that at temperatures within the Ac1-Ac³ ransformation range the austenite grains were acicular in shape. The excess ferrite was also found to be acicular with the distribution of these phases being such that a lamellar pattern was developed. This unusual directional growth of austenite in this new steel initially in the spheroidized condition is illustrated by fig. 1. A search of the literature revealed that this type of growth was not necessarily peculiar to this steel for similar microstructures had been observed by other investigators.4-8 However, the full significance of these microstructures does not appear to have been appreciated, and no work has been done to determine the conditions responsible for this directional growth of austenite or to arrive at an understanding of it. It was for this purpose that the work described in the present paper was carried out. Material: During the course of this investigation a total of 15 steels was studied. They consisted of hypoeutectoid, eutectoid and hypereutectoid carbon steels, and hypoeutectoid and hypereutectoid alloy steels, all of which were obtained in the annealed condition from commercial warehouse stock. As received, the carbon and alloy hypereutectoid steels had microstructures which consisted of spheroidal carbides in ferrite, whereas the eutectoid steel and the hypoeutectoid steels were pearlitic. The grades of steel represented were 1050, 1080, 10110, 3310, 4140, 4340, 4615, 6145, 8620, 9260, 9442,

Jan 1, 1951

By A. E. Nehrenberg

R. A. Schmucker, Jr.—The writer wishes to point out that an acicular growth of austenite, similar to that described in the author's paper, was recently observed in an alloy steel of only 0.06 C content. This steel, which represents an 0.07 max C, 1.35 Cr, 0.55 Ni, 0.20 Mo analysis, combines the characteristics of minimum hardness in the annealed condition with maximum hardenability and is therefore suited primarily for cold-hobbing applications. The acicular austenite formation in this steel was observed accidentally during a determination of its Ac1 temperature. The samples used in this investigation represented as-forged bar stock which had been given a preliminary temper at 1300°F. The critical (Ac1) temperature was finally established at 1400 °F. Fig. 15 represents the microstructure of the sample which had been heated at 1450°F for ½ hr, water quenched, and tempered at 600°F for ½ hr (for the purpose of darkening the martensite). It will be observed from the distribution of the darkened areas of martensite that the parent austenite grains formed at 1450°F had grown in an acicular manner and still occupied only a small percentage of the total area. The remainder of the area contains the original equiaxed ferrite grains in which new austenite had as yet scarcely formed. However, the tiny isolated martensitic patches at several points where three or more ferrite grains intersect indicate that small austenite grains had formed and started to grow in an apparently equiaxed fashion. Fig. 16 represents the prior microstructure of an original sample in the as-forged and tempered condition, before it was heated -above the critical temperature. It is probable that there are two kinds of ferrite in this structure: (1) The equiaxed proeutectoid ferrite grains which separated from the austenite when the steel was cooled from the forging temperature, and (2) the acicular ferrite associated with the aggregate of fine carbide which is represented by the patches of

Jan 1, 1951

By J. D. Grozier, W. W. Mullins, H. W. Paxton

The morphology of the nucleation and growth of austenite into high-purity iron in NH3-H2, gas mixtzires has been studied. The growth rate of an austenitic rim (planar interface) from scratched surfaces of- polycrystalline iron specimens was determined as a function of temperature and percent NH3 and found to he in reasonahle agreement with growth-rate calculations based on a model which assumes the diffusion of nitrogen to he the rate-controlling step. Under certain conditions, austenite pew as platelets; growth rates of these along the surface of single crystals were found to he dependent on surface preparation, orientation, THE development of microstructures can conveniently be thought of in terms of nucleation and growth. The complex topic of nucleation in solid-solid transformations will not be discussed at length, although a few qualitative experiments were performed. Growth is determined by the mobility of the various possible interfaces under the available driving forces in a particular situation. In homophase transformations, it has been clearly demonstrated that the mobility is very sensitive to small amounts of impurities, to the kind of impurity, and to the orientation relations across the boundary.' A degree of quantitative knowledge has temperature and percent NH3. On electropolished surfaces with a (110) pole, the maximum growth rate of platelets was determined and found to be in agreement within a factor of 2 to 3 with theoretical calculations of the edgewise growth rate of a platelet. The calculations are based on a model which assumes that the diffusion of nitrogen in the ferrite in front of the moving curved attstenitic interface at the tip of the platelet is the rate-controlling step. The growth direction on the surface of the single crystal and resztlting habit plane of the platelets were determined and found not to he unique but to vary systematically with the pole of the surface. been obtained. In the case of heterophase transformations, which are significantly more complicated to treat, a comparison of theoretical and experimental studies often shows rather poor agreement.'-' The main purpose of the experiments discussed below was to obtain additional quantitative data on crystallographic effects on boundary mobility in a system which was otherwise as simple as possible, viz. the growth of iron-nitrogen austenite into fer-rite. In the course of the experiments, it became necessary to re-examine the theory for the growth of Widmanstatten plates, especially the influence of anisotropic interfacial free energy. Some other minor experiments in the Fe-N system were performed, and are described briefly. EXPERIMENTAL METHODS A) Material Preparation. The floating zone purified iron used for this investigation was supplied by Battelle Memorial Institute. The nominal composi-

Jan 1, 1965

By J. R. Low, D. F. Stein

Single crystals of iron have been grown from three different lots of Ferrovac "E" of somewhat different chemical composition by the strain anneal technique. Using a technique to seed the crystal similar to Dunn's for silicon-iron, it has been possible to orient the crystals grown in both direction and plane of growth. Crystals having the plane of the strip oriented (100) , (110), (111), (112), (123), and (491) have been grown. The growth directions used have been [100], [110], 45 deg from a [110}, and various others of no specific crystal orientation. The usual dimensions of the crystals were 8 by 1 by 0.08 in. Attempts to grow crystals were about 90 pct successful. METHODS of growing single crystals of high purity iron have been reported in the literature.1-4 However, each of these methods was not completely reliable when used on materials having slightly different chemical composition and in some instances a small number of successes were obtained using identical materials. Except for the method used by S. Dohi and T. Yamoshita,1 it has not been possible to reorient single crystals of high purity iron to give any desired orientation. The method to be described has made it possible to grow single crystals from three different lots of material having different compositions, and to orient the crystals with respect to growth direction and surface. STARTING MATERIAL The material used during this investigation was a vacuum melted high purity iron marketed by the Vacuum Metals Corporation designated Ferrovac "E." Three lots of Ferrovac "E" having the following composition were used with equal success: The compositions listed are those of the as-received material; and they may have been modified before the growth of single crystals. Analysis of heat B just before growth and after growth revealed that the heat treatment prior to growth did not change the carbon content, but the oxygen content was changed from 0.0092 pct to 0.0034 pct and the nitrogen content from 0.0003 pct to 0.0001 pct. After growth of the single crystals, the carbon had dropped to 0.001 pct. None of the heat treatments would be expected to change any of the other impurities very markedly. Heat C would be expected to have a metallic impurity content similar to heats A and B. PROCEDURE Ferrovac "E" iron which had been obtained in bar form having a diameter of about 1 in. was rolled into strip for growing single crystals. By passing the 1-in. bar through a cold rolling mill several times, it was reduced to a strip 0.15 in. thick. The strips obtained were then cut into suitable lengths for heat treating (about 9 in. long), annealed at 925°C for 2 hr in dry hydrogen and water quenched. It was then necessary to bake the strip at 200°C for 24 hr in air in order to prevent cracking during further rolling operations. While it was possible to cold roll the 1-in. bar directly to the desired 0.080-in. strip, the intermediate anneal was used because the strip so obtained produced better single crystals. The strip obtained by rolling the 1 -in. bar directly to 0.080-in. strip produced single crystals having a large number of occluded grains. Experiments showed that the optimum reduction in area by rolling prior to the growth of single crystals was about 50 pct. Attempts to grow single crystals from material that had been reduced less than 40 pct were unsuccessful presumably because the matrix did not possess the critical amount of texture necessary for growth. The strip obtained after the rolling operations had very irregular edges which were ground to give a strip with uniform dimensions. The strip was then annealed at 825°C for 3 hr in hydrogen and furnace cooled. Fig. 1 illustrates the grain size obtained. A temperature of 940°C was used for the annealing temperature on one group of strips

Jan 1, 1962

By J. W. Faust, H. F. John

Generalized conditions for rod or ribbon growth by the twin plane re-entrant edge mechanism are given. It was shown that this mechanism can result in growth of twinned platelets from dilute metal solutions. The platelrts 01 the fee metals are faceted by (111) planes and contain two or more twin planes. Microsegregation traces were revealed in silver grown from a thallium solution. VOGEL has already set down conditions for dendritic growth;1 however, this was the normal single-crystal dendritic growth experienced during solidification. In this work it is desired to set down the crystallographic conditions that will lead to rod or ribbon growth with smooth facets. These are as follows. a) The growth must be crystallographically limited (i.e., faceted growth). b) In order to have directed growth, some mechanism must allow easier nucleation than two-dimensional nucleation. That mechanism is afforded by the re-entrant edges at twin planes.213 Thus there must be twin planes present in the rods or ribbons. c) The growth direction must lie in the twin plane. If not, the twin plane will grow to the face or side of the ribbon and the site of easy nucleation will be lost. d) The growth direction must be parallel to at least one plane of the faceting planes, and no set of the faceting planes can be perpendicular to the growth direction. A corollary to these conditions involves the number of twin planes necessary to maintain the indestructible re-entrant edge. The number depends on the crystal structure of the material. An analysis of the data available shows that a material whose faceting planes form an open figure requires at least one twin plane while materials whose faceting planes form a closed figure require at least two twin planes in order to form the indestructible re-entrant edges for extended growth. The conditions and an assessment of the possibility of rod or ribbon growth are given in Table I for several crystal systems. As can be seen the fee, diamond and zinc blende, or-thorhombic, rhombohedral, and one form of the hexagonal lattice systems can yield this type of growth, but not the bcc metals nor the hexagonal

Jan 1, 1965

By N. E. Rogen, N. J. Grant

WHILE direct measurements of the growth of precipitate particles during aging is of fundamental value, few such measurements have been made. Direct measurements by means of optical or electron-microscopy and X-ray techniques are preferred, however, many of the aging studies have been based on indirect methods such as electrical resistivity and hardness. Because of the minute size of most precipitate particles (less than 1000A) the light microscope is of limited use while electron microscopy is subject to slowness, etching problems and consequent resolution problems. It is fortunate that alloys of the Nimonic type, based on Ni-Cr-Ti-Al, lend themselves to accurate and relatively easy particle size measurements. With proper balance of titanium and aluminum, the only aging precipitate is the gamma prime (r') Ni3,(Al, Ti)2 phase and this phase is the basis of the high-temperature strength of these allos.3-6 The Ni3(Al, Ti) phase is a face-centered-cubic, ordered structure with nickel atoms occupying the cube faces. Titanium atoms can replace three out of every five aluminum atoms and when substituting do so preferentially.2 Electron microscopy has shown that during aging of most of the commercial alloys of this type, precipitate particles are unusually uniform in size and distribution, and that the volume of (r') phase is large (20 pct).4,7 The aim of this investigation was to measure the growth of (y') phase during aging. In so doing, it was hoped that a clearer understanding of the aging process would be attained. X-ray line broadening was used as the measure of precipitate particle size. This technique was selected because it can measure and average the diameter of thousands of particles in one operation. The variations in hardness and matrix lattice parameter with aging were also studied and related to the particle size. EXPERIMENTAL PROCEDURE An alloy of the following composition was studied: Cr Ti A1 C Ni Wt pct 20.71 2.98 1.43 0.04 bal. At. pct 22.06 3.47 2.95 0.18 bal. The alloy, a 15- lb vacuum melt, was forged to 1/2-in. diam at a temperature of 1900" to 2200°F; was solution heat treated for 4 hr at 2000°F and water quenched; and was then aged in various ways. The ASTM grain size was 4 to 5. No (7') phase could be detected by X-ray analysis after solution treatment and electrolytic extraction. Aging was performed on 2-in. long specimens at 1400°, 1500°, and 1600°F for increasing times. One-half inch sections were removed after each time increment and were then electropolished in a solution of H3P04 saturated with chromium trioxide at a potential of 30 v and rectified with a tantalum electrode. Rockwell hardness measurements were taken using one side of the polished specimen. Matrix lattice parameter determinations were made on the other side using filtered chromium radiation references with the position of the (220) line of a silicon standard. To enable the precipitate particles of the (y') phase to be measured using X-ray line broadening techniques, it is first necessary to separate and concentrate this phase by electrolytic extraction. Extraction is necessary because the difference between matrix and precipitate lattice parameters is only approximately 0.5 pct and intensities of.the (y') phase lines are very weak relative to those of the matrix. The extraction techniques employed have been described before and found to produce a reasonably quantitative separation.398 A water solution of 15 pct H3Po4 is used at a current density of 0.5 amp per sq in. at 6 v. The precipitate particles are separated from the liquor by centrifuging and decanting and are then washed, dried and repowdered. A plot of the X-ray intensity vs diffraction angle for the (111) line of the precipitate particles was used as a measure of particle size. The intensity curve approximated the shape of Gaussian distribution function and its breadth was measured at the half height. The (220) line of a silicon standard was used to correct the measured line breadth for instrumental and other broadening errors. The Scherrer formula was used to calculate particle

Jan 1, 1961

By J. S. Kirkaldy, D. H. Weichert, G. R. Purdy

Two-phase diffusion couples have been used to simulate the growth of proeutectoid ferrite in ternary Fe-C-Mn austenites. It has been shown, theoretically and expermentally, that the results fall into two classes: a high-super saturation class in which the major role of manganese additions is to influence the boundary conditions for carbon diffusion; and a low-supersaturation class in which the partition of manganese is required. In the latter case, a drastic inhibition of the reaction rate is to be expected. As an aid to the kinetic analysis, a portion of the iron-rich comer of the Fe-C-Mn constitution diagvam has been determined. The conclusions drawn from this work have a direct bearing on the kinetics of the grain boundary ferrite precipitation reaction and thus yield insight into the manner in which alloying elements can influence the rate of austenite-decomposition reactions. THE role of alloying elements in the austenite-decomposition reactions has provoked considerable interest, since it is apparent that an understanding of this phenomenon will yield insight into the harden-ability problem. In the present investigation, attention is focused upon the proeutectoid-ferrite transformation in the system Fe-C-Mn, and upon the manner in which manganese additions affect the growth rate of ferrite. When hypoeutectoid austenite is supersaturated, the ferrite first formed usually exhibits two distinct types of morphology. At low super saturations, grain boundary layers grow into the austenite grains with an approximately planar interface, and usually possess at least one incoherent phase boundary. At high supersaturations, Widmanstiitten plates appear, which bear an orientation relationship' to the parent austenite. In this case, there is a chance of partial lattice matching along the sides of the plates and an attendant semicoherent interface structure. Purdy and Kirkaldy2 have used a two-phase binary Fe-C diffusion couple to demonstrate that carbon volume diffusion controls the incoherent reaction, while Rouze and rube,' using thermionic-emission microscopy, have shown that the thickening of Widmanstatten ferrite plates is appreciably slower than expected for carbon-diffusion control. This suggests that the plates are bounded by partially coherent, low-mobility interfaces. The redistribution of alloying elements during transformation has been the object of studies by Aaronson4 and owmman,5 who have shown that no alloy partition occurs during ferrite precipitation in the systems Fe-C-Cr and Fe-C-Mo, respectively. More recently, Aaronson et al.6 have shown that some manganese partition occurs at low super-saturations in the system Fe-C-Mn, but that no partition occurs at higher super saturations. Pickle-simer et al.7 observed that no manganese partition occurred during the early stages of the pearlite transformation in a manganese steel, and concluded that volume diffusion of the alloying element is not the rate-deter mining factor. The diffusion coefficients pertinent to this investigation have been measured by Wells, Batz, and Mehl8 (carbon in austenite), R. P. smith9 (carbon in ferrite), Wells and Mehl 10 (manganese in austenite), and Kirkaldy and Purdy11 (diffusion of carbon on a manganese gradient in austenite). Kurdjumov 12 has shown that the diffusivity of substitutional elements in ternary austenites up-quenched from martensite may be greatly enhanced, due, apparently, to the presence of a persistent defect structure. The recent work of Krauss 19 showing high densities of tangled dislocations in reversed Fe-Ni martensite is in agreement with this conception. THEORETICAL Diffusion in ternary or higher-order systems may be described with the aid of Onsager's extenbion of Fick's first law,14 in which the flux of each of the n components is assumed to be a linear function of all concentration gradients:

Jan 1, 1964

By H. R. Peiffer, R. Geckle

The silver phase of silver and finely divided alumina composites is shown to grow as single crystabs upon solidification from the melt. These crystals grow without the aid of an externally applied thermal gradient or a mold. The single-crystal growth is more readily disrupted as the alumina content varies from the optimum concentration of 20 wt pct. Pretreatment such as variation of fabrication pressure, and presintering of the specimens appear to play a lesser role in this phenomenon. In actual practice the growth of single crystals of metals from the melt is a tedious, painstaking process.' Care must be taken to insure the proper thermal gradients and rate of growth in a vibration-free environment. Excellent single crystals can be grown when these variables are controlled. When a second insoluble and finely divided phase is present in the melt the growth of single crystals is difficult, if not impossible, even under the most favorable conditions outlined above. During the past few years, a composite of silver and alumina has demonstrated an ability to resist flow even though the major phase, silver, is mo1ten. 2 A more surprising feature of this material is the ease with which single crystals of silver grow upon cooling the composite from temperatures above the melting point of silver to temperatures near room temperature. Observations have been made that demonstrate that single crystals of silver will grow even when conditions most unfavorable for growth of pure silver crystals exist. The crystals grown in this manner are imperfect in that a great deal of subgrain structure exists. It is the purpose of this manuscript to qualitatively describe this process and to attempt to isolate the influencing factors of this behavior. MATERIAL PREPARATION The composite material is prepared by powder-metallurgical techniques. Two items of great importance are the introduction of oxygen into the system and the obvious need for a thorough mixing of the metallic and refractory oxide phases. The oxygen is necessary in order that the silver wets the alumina. Without oxygen the phases separate and the material shows no unusual properties. In order to supply the needed oxygen the silver is added in the form of silver oxide which is readily decomposed to oxygen and silver upon heating. The silver oxide is readily obtained in a finely divided form that allows a uniform mixture of the alumina and silver oxide to be prepared. The correct ratio of alumina to silver oxide is mixed in the presence of alcohol in an ordinary food blender. The mixture has the consistency of a thin slurry and after mixing for approximately 20 min is dried and pressed into billets at various pressures. As is shown in Fig. 1, there is no limit to the shape of the specimens obtainable as single crystals. These billets are heated in air in a predeter-

Jan 1, 1964

By G. R. Speich, Morris Cohen

The growth rate of bainite has been determined by hot-stage metallography in five hypereutectoid high-purity iron-carbon, iron-carbon-chromium, and iron-carbon-nickel alloys. The studies have been confined essentially to lower bainite. The growth rate is independent of time at constant temperature, but both the edgewise and sidewise growth rates increase with increasing temperature. Increasing the carbon content, or adding chromium or nickel, decreases the growth rate without greatly affecting the temperature dependence. The results lead to separate diffusion-controlled models for the edgewise and sidewise growth rates. ALTHOUGH bainite has been subject of many detailed investigations,1,2 the growth mechanism of this intermediate transformation product of steel remains unclear. One difficulty has been that practically all the kinetic measurements have been restricted to studies of the overall reaction rate. Only a limited amount of information3, 4-6 is available on the growth process itself. The purpose of the present work was to investigate the effect of time, temperature and composition on the growth rate of bainite using hot-stage metallography. This method makes it possible to observe continuously the isothermal growth of individual bainitic units because of the surface upheavals accompanying their formation.3 This information is needed to test the existing growth models and to obtain a better understanding of the factors controlling the bainitic transformation. EXPERIMENTAL PROCEDURE Alloys—The compositions of the alloys used in the present work are shown in Table I. The five alloys were vacuum-melted and cast, and were prepared from high-purity materials. The three iron-carbon alloys were available from the work of Roberts et al.7 in the form of 3/8-in. diam rods.* To facilitate machining, the rods were ing. The rods were then tempered for 3 hr at 650°C to allow machining. The iron-carbon alloys in Table I were selected for investigating the effect of carbon on the bainitic growth rate. Due to the rapidity of the transformations involved, it was not feasible to measure the growth rates in iron-carbon alloys having carbon contents much less than 0.9 pct C. The iron-carbon-chromium and iron-carbon-nickel alloys were selected to study the influence of chromium and nickel on the growth rate at a carbon level of about 1.1 pct C, since this carbon content was intermediate among the iron-carbon alloys. The concentrations of chromium and nickel were chosen to match isothermal trans formation diagrams in the literature.8'9 Hot-Stage—Since the iron-carbon alloys had such low hardenabilities, it was necessary to quench the hot-stage specimens drastically from the austentiz-ing temperature to the isothermal transformation temperature to prevent the formation of pearlite or proeutectoid constituents. A rapid-quenching metal-lographic hot-stage was built for this purpose. A maximum temperature of about 1100°C and quenching rates up to 500°C per sec could be attained with this equipment. The details of the apparatus are described in a recent publication. After being polished and mounted on the hot-stage, the specimen (0.020 in. thick) was protected from oxidation and decarburization during austenitizing by a vacuum of 10-4 to 10-5 mm. The quench to the reaction temperature was accomplished with a helium blast, and the isothermal run at this temperature was conducted in a helium atmosphere. A fine-wire thermocouple spot-welded to the sample and a high-speed

Jan 1, 1961

By R. V. Sara

Determination of the Hf-C phase diagram was conducted primarily by metallographic and X-ray diffraction studies on appropriate alloys. The only intermediate phase observed in this binary system was HfC. This phase was found to be homogeneous between 34.0 and 48.0 at. pct C at 2200°c and between 36.0 and 49.3 at. pct C at 3150°C. The lattice-parameter variation was also determined for HfCI-, compositions prepared at 2200° and 3150°C. The most most refractory composition, with a melting point of 3830°c, was established at 47.5 at. pct C from melting-point data. Solidus temperatures of 2240' and 3150°C occur on the high-kafnium and high-carbon sides of the monocarbide, respectively. The invariant point between HfC and carbon is located at 66.0 at. pct C, whereas the 2240°C solidus corresponds to the peritectic temperature at which hafnium is formed from HfC and hafnium-rick liquid. Hafnium has a melting temperature of 2208°C and is capable of taking carbon into solution to the extent of 10.5 at. pct at this temperature. ALTHOUGH the Hf-C phase diagram has not been previously evaluated experimentally in its entirety, the belief has been that the general configuration would resemble the chemically similar Group rV carbide systems, Ti-C and Zr-c.' These binaries are characterized by a single carbide phase with a simple NaC1-type structure which is maintained over wide compositional ranges. This family of carbides has high thermal stability that increases substantially as the atomic number of the metal component increases. This trend characterizes HfC as one of the highest melting materials. According to Agte and Alterthum,2 the melting point for this monocarbide is 3890°C, a value that has been quoted quite extensively for the past several decades. Recently, in repeating the work of Agte and Alter-thum, Adams and Beall3 determined the melting point of HfC to be 3895°C. A significant departure from the commonly accepted version of the Hf-C system was reported by Avarbe and his coworkers,4 who proposed that there is an extreme stabilization of a hafnium in a narrow field to 2820°C, above which it melts peritectically to form HfC and liquid. Their study was also concerned with the melting temperature of various HfCI-, compositions, but the peak melting point was taken from the work of Agte and Alterthum. Avarbe and his associates were not concerned with the high-carbon region of the system. However, three widely varying temperatures have been reported for the HfC-C solidus by other investigators. Cotter and Kohn5 observed approximately 2800°C; Portnoy et al.' reported 3260°C; and, more recently, Krikorian7 indicated 2915°C. Equally as uncertain is the solidus between hafnium and HfC. As noted above, Avarbe et al. report a peritectic temperature of 2820°C, Krikorian7 measured 2150°C, and Benesovsky and Rudy' estimated 2000°C on their diagram. I) EXPERIMENTAL PROCEDURE The starting materials for this study consisted of reactor-grade hafnium hydride obtained from Fair-mount Chemical Co., Newark, N.J., hafnium carbide supplied by Wah Chang Corp., Albany, Ore., and Union Carbide spectroscopic-grade graphite, SP-1. The graphite analysis indicated impurities at levels of only 0.5 ppm or less. According to the suppliers, the hydride and carbide contained the typical impurities listed in Table I. The samples required for these studies were prepared by dry blending either graphite and hafnium hydride or hafnium hydride and hafnium carbide powders for approximately 5 min in a "Spex Mixer Mill". The latter combination was used only for preparing several samples in the HfC1-, melting-point studies. Small pellets, varying between 3/16

Jan 1, 1965

By J. L. Giove, J. M. Hodge, R. G. Storm

The hardenability effect of molybdenum has been evaluated by a number of investigators, including one of the present authors.1,2,3,4,6 Considerable discreMncy exists, however, among the results of these various investigators, and two of them, Brophy3 and Kramer,4 have indicated that the apparent hardenability effect of molybdenun would vary, depending upon the other alloying elements in the steels being considered. The results of previous, unpublished work conducted at the Duquesne Works Laboratory of the Carnegie-Illinois Steel Corporation also have indicated significant differences in the hardenability effect of molybdenu~n in nickel and in chromium steels. The present investigation was undertaken in an effort to establish the mechanism governing this difference in the hardenability effect of molybdenum. This work involved both end-quench hardenability and isothermal transformation tests on two series of steels of varying molybdenum content. One steel contained 3 pct nickel and the other 1 pct chromium. It was hoped that such studies would shed further light on the mechanism of this behavior. Materials and Experimental Work MATERIALS The chemical compositions of the steels used in this investigation arc shown in Table 1. These steels were furnished by Battelle Memorial Institutc in the form of 100-lb induction furnace ingots. The top half of each ingot was forged to 1 3/8-in. square billets and then rolled to I-in. round bar stock for isothermal transforma- tion studies. The bottom half of each ingot was forged into approximately 1 1/4-in. rounds for end quench tests. All of the steels were normalized from 1650°F and tempered at 1100°F before nlachming to end quench or isothermal samples. END-QUENCH TESTS standard l-in. diam end-quench tests were made on each of the steels. The test bars were austenitized at 1600°F for 30 min,, quenched in a standard Jominy jig, and hardness surveys were made in all tests. The 95 pct martensite point was deterInined from hardness values5 and cheeked by metallographic examination. The jominy distance values for 95 pct martensite were converted to hardellability values in terms of ideal diameter (Dl), using a revised carve for the relationship between Jominy distance and ideal diameter. This curve was based on the cooling time from the A1 to the bainite nose temperatures rather than on the usual criterion of half-temperature time. The cooling rates as determined by Russell and Williamson9 were used as a basis for this relationship. The derivation of this curve is described in detail in the appendix. ISOTHERMAL TRANSFORMATION STUDIES Samples for the isothermal transformation studies were quarter sectors of 1/16.is-in. thick slices from the 1-in. round bars. All samples were austenitized for a total the of 15 min., transferred rapidly to a lead bath for isothermal transformation, and brine quenched from the lead bath. A time of 3 see was allowed for the sample to come to the temperature of the lead bath, and this time was not included in the isothermal transformation times. Each sample was examined metallo-graphically at a magnification of 100 diam. The per cent transformation was estimated by comparison with standard micrographs, and the values were plotted against the on log/log coordinate paper. At least 4 and as Inany as 10. points were plotted for each steel. A line was drawn through the points for each steel, and the times for 5 pct transformation were obtained from the plot for each steel. Isothermal transformation diagrams in terms of 5 pet total transformation, covering the temperature range of 800 to 1200°F, were determined in this manner for an austenitizing temperature of 1600°F. The times for 5 pct transformation at the bainite nose for austenitizing temperatures of 1800 and 2000°F were also determined in the same manner. These times for 5 pct total transfor-

Jan 1, 1950