Search Documents

By A. T. Miesch, L. B. Riley

Distribution of minor elements in sandstone-type uranium deposits of the Colorado Plateau is being studied by the USGS on behalf of the A EC. A primary objective has been to provide basic data which could be useful in geo-chemical exploration for new deposits. The basic statistical measures — similar to those used in sedimentary petrology—are described. The underlying principle is that the frequency distributions fit or approach the log-normal form. Since 1952 the U. S. Geological Survey on behalf of the U. S. Atomic Energy Commission has conducted a study of the distribution of minor elements in sands tone-type uranium deposits of the Colorado Plateau. A primary objective in this study has been to provide basic data which could be useful in geo-chemical exploration for new deposits. Among the basic data considered important are estimates of the abundance and habit of each element in the ore and in the host rocks. It has been found that a few basic statistical techniques, and variations of these techniques, are useful in this type of study. Some of the basic techniques have been used to advantage by researchers in geochemistry and in other fields of geology, especially sedimentary petrology; others have been used to only a limited extent. Among the latter is the linear correlation coefficient, which has proved useful in assessing the element associations in a particular rock type without analysing individual mineral separates. In computing the basic statistical measures a scale has been used which is, in some ways, similar to the phi ($) scale used by sedimentary petrol-ogists in grain-size studies.' FREQUENCY DISTRIBUTIONS It has been recognized for some time that the results of analyses for a given minor element in a suite of samples of rocks or ores yield frequency distribution curves which are approximately normal when the curves are plotted on logarithmic or geometric scales. In other words, the analytical results give an approximate lognormal frequency distribution. A classical example is given by D. G. Krige2 in the study of the distribution of gold values from a mine on the Witwatersrand. Another example is shown in Fig. 1, the distribution of barium concentrations in samples of uranium ore from the Chinle formation. The geochemical data are analogous to grain-size data gathered by the sedimentary petrologist. Both types of data, after simple logarithmic transformations, may be treated by conventional statistical methods based on the normal distribution. This is not to say that other types of transformations may not serve equally well or better for particular element distributions.3 Spectrographers and other analysts are quite aware of the dependence of their precision on the concentration of the element present.4 For example, in the part per million range the variation may

Jan 1, 1961

By A. T. Miesch

The purpose of this paper is to explore relations between the distribution and composition of uranium deposits on the Colorado Plateau and mineralogic, chemical, and lithologic aspects of their host rocks. The paper also appraises the host-rock sandstones as possible sources of elements in the uranium deposits. Other possible sources of elements are not discussed. Uranium deposits on the Colorado Plateau consist largely of sandstone and small amounts of mud-stone impregnated with uranium and vanadium miner- als and a suite of minor accessory minerals containing copper, lead, zinc, silver, iron, cobalt, nickel, yttrium, molybdenum, selenium, and arsenic, in addition to other elements locally. The deposits consist of clusters of closely spaced ore bodies which commonly aggregate several thousand tons, but range in size from less than one ton to several million tons. With only rare exception, the deposits show no close relation to fractures. The ore bodies are generally tabular in layers nearly parallel to the bedding in the host rocks, or they cross bedding at large angles to form roll structures. Absence of fracture control necessitates that the ore and associated elements were transported to the deposits by way of interstitial pore spaces in the sandstones. This points to the general process of lateral secretion as a possible mechanism of ore formation, and suggests the host-rock sandstones as a possible source of the metals. Roll structures in the ore

Jan 1, 1962

By A. D. Hoagland

The Flat Gap mine is located on Copper Ridge in the Appalachian Valley of East Tennessee. Large zinc orebodies occupy zones of solution and collapse breccias in Lower Ordovician Kingsport limestone and dolomite. The principal ore mineral is sphalerite and the principal gangue is dolomite. The ore-bearing horizons are considerably more than 95% covered by thick residual clay. Geochemical prospecting under these conditions is an effective exploration technique which played an important role in the discovery and exploration of the Flat Gap mine. The Flat Gap mine, an important zinc deposit of the Appalachian type, is located in the Copper Ridge Belt in the Valley of Tennessee approximately 30 miles northeast of the Mascot-Jefferson City zinc district (Fig. 1). The ore is found in large stratigraphically linked deposits in solution and collapse breccias of the Kingsport, Longview and, to a minor extent, Mascot formations of Lower Ordovician age. The principal ore mineral is sphalerite and the principal gangue minerals are dolcrmite and accessory pyrite. There is local minor galena and very rare barite and fluorite. The ore-bearing horizons are covered by about 20 to 100 ft or more of residual clay except where active streams have exposed bedrock. Considerably less than 5% of the favorable host rocks are exposed in outcrop, and this nearly complete soil cover creates a serious obstacle to exploration. Comprehensive surveys of the base metal content of soils furnish a useful substitute for outcrop geology, and under favorable conditions, this technique is a very valuable prospecting tool. The analysis is carried out by a titrametric dithizone method modified after the procedure described by E. B. Sandell.' This method detects

Jan 1, 1962

By E. E. Thurlow

The Geology Div. of Northern Pacific Railway Co. has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photo-geologic interpretation. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occa sional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted. Northern Pacific's program of reconnaissance mineral evaluation of company-owned lands and adjoining areas was outlined in a paper presented at the American Mining Congress meeting in Las Vegas four years ago. That report included policies and procedures with respect to mineral development on Railway Co. lands and may be referred to for information on these matters.1 In a sense this paper is a progress report on the use of geochemical prospecting in Northern Pacific's continuing mineral evaluation program. At this time there are positive results but as yet there is no real success story in the form of a minable ore body. GEOCHEMICAL PROSPECTING PROCEDURES The decision to use geochemistry as a reconnaissance exploration tool must be followed by research into sampling and analytical methods and into the interpretation of results. Various analytical methods were tried and evaluated by the Geology Div., including hot and cold acid extraction with and without fusion of the sample, panning and magnetic separation followed by dithizone testing of the magnetite, and cold aqueous extraction of metallic ions followed by indicator tests. Samples were first sent to the laboratory for analysis; later field laboratories were established and now virtually all testing is done at the sample site. It was concluded that, where applicable, the quickest dependable methods for reconnaissance use are the dithizone field tests for readily extractable heavy metals. This involves the simultaneous treatment of a sample, usually of soil or stream sediment, with two immiscible liquids; one a cold aqueous extractant (ammonium citrate) and the other a solution of dithizone in toluene or xylene.2 Dithizone is a colorimetric indicator that reacts quantitatively with copper, lead, zinc, and several other metals to form colored complexes in organic solvents. Results may be expressed in ml of 0.001 pct dithizone that are required to reach the blue end point, or calibration of the test results can be carried out with standard solutions of zinc; conversion factors would then be expressed in ppm, zinc equivalent. Calibration of dithizone solution with zinc standards indicates that 1 ml of 0.001 pct dithizone is equivalent to approximately 0.25 ppm of zinc. An authoritative report on dithizone field tests authored by H. E. Hawkes in the June-July 1963 issue of Economic Geology* states "The appeal of these techniques has been the simplicity and speed of the determinations as compared with more tedious laboratory determinations of trace metals in weathered rocks, soils, or plant materials. This obvious appeal, however, has often been more than matched by misuse of the method in such a manner that the results are

Jan 1, 1964

By G. W. Leney

Iron ores occur in such a wide variety of forms that nearly every kind of prospecting, geological knowledge, and geophysical technique has some application in the search for them. The type of orebody that is considered desirable depends on political and economic considerations, on transportation and markets, on the characteristics of the orebody, on the metallurgy of the ore, and on its comparison with other available ores. In North America, materials that can be efficiently processed into high grade concentrates and pellets are now the object of most exploration work. These are usually shallow, relatively unoxidized, metamorphosed iron formations that are particularly suitable for geophysical methods of exploration. Magnetic surveys are used for the direct discovery of new orebodies, for mapping stratigraphy and structure, and at times to locate oxidized zones in magnetic iron formation. Gravity mapping provides supplementary information, indicates gross tonnages, is useful in regional studies, and can discover non-magnetic orebodies. Electrical methods have not been fully exploited but self-potential, resistivity, applied potential, electromagnetic and perhaps induced polarization surveys all have restricted but highly useful applications. The use of all geophysical techniques promises to increase as the number of exposed easily discoverable orebodies decreases. A high consumption of steel, and consequently of iron ore is the chief characteristic of an industrial society and this consumption has been increasing at an average rate of about 35% every ten years for the past century. To supply this demand, iron ores and iron bearing materials in a wide variety of forms have been exploited on every inhabited continent and in nearly every country. Nearly every kind of prospecting, geological knowledge and geophysical technique has some application in the search for them. The type of orebody that is con-

Jan 1, 1964

By R. A. Bell, R. Schultz, P. G. Hallof

The Ballyvergin area is located in County Clare on the southwest coast of Ireland. It is one of six areas in County Clare in which mining operations were carried out during the last century. The ores mined were high grade Cu-Pb-Ag deposits in the form of small fracture fillings and gash veins in the lower Carboniferous limestones. The zone of primary economic interest is situated on the north limb of a geosyncline which plunges moderately to the southwest. The zones of mineralization previously mined were associated with local structures and folds, and the initial geophysical investigations took the form of reconnaissance induced polarization measurements around, and between, the old mines. This work located an anomaly which, on drilling, resulted in a small extension of the Pb-Cu ore at the Ballyvergin mine. However, a potentially more important zone of mineralization resulted from the drilling of another IP anomaly near Ballyvergin. This wide anomaly was found to be a domal shaped deposit of disseminated chalcopyrite located at a depth of more than 100 ft. The deposit is controlled by local folding in the sediments and is of a type previously unknown in the area. More IP investigations are under way to locate other deposits of the same type. The Ballyvergin area is located in County Clare, about 35 miles northeast of Shannon Airport, near the Atlantic west coast of Southern Ireland (Fig. 1). Interest in the area stems from a number of occurrences of small, but high grade, Pb-Ag deposits. From the summer of 1960 to the spring of 1961, Irish Base Metals carried out a comprehensive exploration program on a 38-sq mile concession in east-central County Clare in an attempt to locate additional deposits of this type. Field operations consisted of geologic mapping, geochemical soil and stream sampling, geophysical surveying and diamond drilling. The geophysical program consisted primarily of detailed induced polarization (IP) surveys in the general vicinity of old mine workings, supplemented by electromagnetic and self-potential investigations. Subsequent diamond drilling of a well defined IP anomaly close to the old Ballyvergin mine disclosed a sizeable deposit of low grade disseminated copper, a type of deposit previously unknown in this area. REGIONAL GEOLOGY Topography: The topography is of the Karst type with low regional relief. The northern parts of the area are covered almost completely with glacial deposits including a large number of drumlins. Elsewhere the overburden is patchy and only moderately deep. A close network of roads makes every part of the area readily accessible, and rail and harbor facilities are available nearby — Fig. 2. Stratigraphy: The area was mapped on a reconnaissance basis by the Geological Survey of Ireland during the latter part of the 19th century at scales of 1 and 6 in. to the mile. Mapping is complicated in

Jan 1, 1962

By R. L. Mauger, P. E. Damon, B. J. Giletti

This report includes the lead isotopic dating of a suite of galenas from Arizona and an application of the K-Ar method to the dating of a Laramide porphyry copper deposit, the Silver Bell Mining District. The lead isotopic data supports prior age assignments based upon geologic inference. The Silver Bell study illustrates the necessity of correlative geologic and petrographic investigations for the interpretation of the results of potassium-argon dating. LEAD ISOTOPIC DATING OF GALENAS FROM ARIZONA ORE DEPOSITS A group of galenas from Arizona ore deposits have been analyzed for lead isotope ratios. The results were used to calculate model ages by the. method of Russell, Stanton and Farquhar,l6 in which the age is calculated directly from the Pb206/Pb207 ratio. The use of Pb206/Pb207 ratios eliminates the errors inherent in measuring the abundance of Pb204. The Holmes-Houtermanns model is the other model commonly used for calculating model ages. Both models assume that any lead sample is composed of primeval and radiogenic components and the calculated age is the time at which the lead was extracted from its source area. Using the Holmes-Houtermanns model, a lead is ordinary if its isotopic ratios lie on an isochron. The growth curve that passes through the experimental point determines the U/Pb ratio in the source area. The RSF model assumes the source area for conformable leads is the mantle, that this has a uniform U/Pb ratio, and thus all ordinary leads must lie on a single growth curve, having a mantle U/Pb ratio. The definition of an ordinary lead differs between the models, and differences in age arise mainly from the assumptions made to evaluate parameters in the model equations. These assumptions depend on the hypothesis chosen to explain ore genesis. In the RSF Model, the Pb206/Pb207 ratio is derived as a function of time. The equation contains three undetermined parameters which are evaluated by assuming three known points lie on the curve. These are the following: 1) Primeval lead from the Canyon Diablo and Henbury meteorites, 2) Modern conformable leads which lie on Patterson's zero isochron, 3) Lead from the Bathurst, New Brunswick base metal deposits. The Bathurst deposits are postulated to be examples of "conformable base metal deposits", as proposed by Stanton.l9 A conformable deposit has a particular genetic history and, as a result, the orebody conforms to stratigraphic layering in the host rock. The metals are brought to the surface in volcanic rocks which originated in the mantle. Weathering products of these rocks, including sulfur and metals, accumulate in areas undergoing sedimentation. The formation of sulfide ion in the sediments by the action of sulfate reducing bacteria causes fixation of iron as pyrite. If the pyrite becomes concentrated in favorable stratigraphic horizons, any base metal deposit eventually formed by replacement of pyrite will have a strata bound character. Compaction and expulsion of pore water from the sediments at depth result in upward mobility of solutions containing soluble base metal chlorides. The strata with high pyrite content act as chemical traps for the base metal ions and replacement occurs. An important result of this general evolutionary model is that, if complete separation of lead and parent isotopes occurred during accumulation of the sediments, any ore deposit formed solely of metals derived from those sedimentary rocks will contain "conformable" lead. This would be true even if the actual ore deposit were formed at a later date by some epigenetic process. In this case, mineralization would be controlled by local conditions, and need not conform to stratigraphic layering. Also, any ore deposit containing lead derived from a mantle or mantle-like source, even though not conformable in Stanton's sense, will fall on the curve for conformable ores and thus give a meaningful model age. Model ages for Arizona galena deposits are listed in Table 1. Fig. 1 is a location map. Jerome-Humbolt District: Galenas from the United Verde mine at Jerome and the Iron King mine at Humbolt give model ages of 1750 m.y. and 1640 m.y. respectively. Both deposits are massive sulfide bodies in a host rock of older Precambrian

Jan 1, 1965

By D. N. Stevens, D. N. Bloom, M. A. Klugman

This paper represents a portion of a larger study concerning dispersion of major, minor and trace elements in wall-rock about orebodies in part of the Colorado Mineral Belt. This phase of the work pertains to the Mg/Ca ratio variations in wall-rock adjacent to orebodies in two mines, one in the Horseshoe Mining District (Hilltop mine), and the other in the Alma Mining District (Phillips mine). The two districts lie adjacent to one another, the Horseshoe District on the south and the Alma District on the north, and are commonly referred to as one, the Alma-Horseshoe Mining District. The Alma-Horseshoe Mining District is located 80 miles southwest of Denver, Colo., (Fig. 1) in Park County, on the eastern slope of the Mosquito range. The area is typified by rugged relief with altitudes of from 10,500 to 14,000 ft. The Horseshoe District is separated from the Lead-ville Mining District by the crest of the Mosquito range, with the Leadville District to the west. The Alma-Horseshoe District has been considered as peripherial to the Leadville District, and has not received the detailed attention that the Leadville District has. These two mines were selected for this study because of their ease of access; the attitude of the workings and the drill holes to the known mineralization; the similarity of the mineralization; and because the mineralization occurs in carbonates in both mines but are of different ages. In the Hilltop mine mineralization is confined to the Leadville dolomite (Mis-issippian) and is principally lead with subordinate zinc and silver. In the Phillips mine the mineralization occurs in the Peerless dolomite and shale (Cambrian) and in the Manitou dolomite (Ordovician) and is principally zinc with subordinate lead, silver,

Jan 1, 1964

By H. E. Swanson

A description of the field apparatus has been published by D. G. Brubaker. Data from laboratory model studies of the in-line and broadside methods of operation are detailed. The conductor models include a single sheet conductor at several strike and dip angles and a schistose-type conductor. In addition, data on the effects of the strike length and of the depth of the conductor are presented for the broadside method of operation. All of the data show that the inclintion reverses direction over the top edge of dipping single sheet conductors. Differences between anomalies over conductors dipping between 90" and 30" are subtle,but flat-lying sheets can be readily distinguished from steeply dipping sheets. Schistose conductors are easily distinguished from single sheet conductors, and a procedure is given for determing the direction of schistosity. The depth of penetration under ideal conditions is 0.7 of the coil separation. In 1950, The New Jersey Zinc Co. (of Pa.) developed a lightweight apparatus for electromagnetic prospecting. A description of this apparatus has been published by D. G. Brubaker.1 It consists of a small, battery-powered vertical source coil and a direction-finding receiving coil. Source and receiver are kept a fixed distance apart and move as a unit along the survey lines. At each receiver station the inclination of the magnetic field created by the source is measured. Two methods of operation are used, in each of which measurements are taken with a constant source-to-receiver distance and with the plane of the source oriented to pass through the receiver station. In one procedure, called the in-line method, source and receiver travel in tandem along the same line. In the other procedure, called the broadside method, source and receiver move along adjacent lines, with the source-to-receiver direction oriented parallel to the assumed strike direction. The data recorded in either case are the inclinations, measured in degrees from the horizontal, of the magnetic field created by the source. These data are plotted at the receiver stations on a map. Scale-model studies of both methods of operation have been conducted in the laboratory and are reported in this paper. APPARATUS Small source and receiving coils wound with many turns of fine copper wire were used to produce and measure an alternating magnetic field in the same manner as the field apparatus. The model source coil was mounted in a vertical position and oriented so that the receiving coil was in the plane of the source. The receiving coil was mounted in a frame so it could be rotated to obtain the inclination measurements. The source coil was excited by a 100-kc signal generator. A tuned amplifier and a voltmeter were used to detect the null position of the receiving coil. The coils used in the field apparatus are usually spaced about 400 ft. The coils used in the model work were spaced from 4 in. to 4 ft apart. Thus the scale of the model work ranges between 1/1200 to 1/100 natural size. The model conductors were aluminum-coated building paper supported on wooden frames. The conductivity-thickness product was measured using a four-electrode system and was found to be about 300 ohms-'. CONDUCTIVITY CONSIDERATIONS The electromagnetic response from a thin sheet conductor is a function of the product of the conductivity of the sheet times the thickness of the sheet times the frequency of the alternating electromagnetic field times some linear dimension of the system such as the coil separation which indicates scale. The secondary electromagnetic field produced by the conductor increases in amplitude from zero at zero conductivity to a maximum value for infinite conductivity, while the phase of the secondary field with respect to the primary field shifts from 90" at zero conductivity to 0" at infinite conductivity. Several authors2-' have shown that most of both the increase in amplitude and the change in phase of the secondary field takes place over a three-decade range of the conductivity-thickness-frequency product. Only small changes in the amplitude and

Jan 1, 1961

By C. P. Miller

In order to determine the usefulness of geochemical and biogeochemical prospecting for nickel, ten localities representing several types of nickel occurrences were selected as sites from which to collect plant and soil samples. This report covers the investigations in two of the areas. After a brief geologic description of the areas, the author presents details of the experimental tests and resulting data. Conclusions drawn from the studies led to several general guides for further prospecting. In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about three years ago, approximately ten localities, representing several different types of nickel occurrences, were sampled and about 1500 samples of plant and soil were collected. This report will cover briefly the data and results for two areas, and a summary of guides for prospecting. DESCRIPTION OF AREAS SAMPLED One locality is the Red Flats nickel prospect in Curry County, Ore., about six miles southeast of Goldbeach, and the other is the Little Rocky Creek prospect in Stillwater County, southcentral Montana, just southeast of the Benbow chromite mine. The Oregon area is a lateritic-type nickel deposit formed on a nickel-rich serpentinite peridotite complex, similar to the Josephine intrusion in southwestern Oregon. The Montana area is a nickel prospect in norite, peridotite, and related rocks of the Stillwater igneous complex. The Stillwater complex is a series of layered basic and ultrabasic rocks, with a layer of norite-gabbro at the base and a series of peridotites and gabbros above. The nickel in the Oregon deposit occurs in both the peridotite and the overlying soil. A deep lateritic soil is developed locally on the peridotite and serpentinite and constitutes the ore. The average nickel content of the lateritic soil is less than 1 pct, whereas the nickel content of the weathered peridotite is about 1 to 1.5 pct. The nickel occurs as garnierite (Mg, Fe, Ni, Mn)3 (OH)4 (SiA1)2O5 in the soil and in the olivine and pyroxene in the peridotite where it probably substitutes for Fe2+ or Mg2+ in the silicate lattices. Nickel is found in three distinct ways in the Still-water rocks: 1) it is in the olivine and pyroxene minerals in norite, harzburgite, etc.; 2) it occurs as widely disseminated grains of pentlandite-pyr-rhotite, which tend to be concentrated in the lower norite band; and 3) it occurs as discrete bodies of pentlandite-pyrrhotite and chalcopyrite which are localized in the norite zone, close to the contact with the underlying rocks. The nickel content of the norite is probably less than 1 pct, and the nickel content of the pods and lenses within the norite is about 1 pct. PROSPECTING APPROACH Although the areas are different geologically, the approach in prospecting them is fundamentally the same. The procedure is twofold: 1) a rapid reconnaissance survey to outline an area of high nickel content, and 2) a more detailed survey to outline zones of possible ore grade within the area of high nickel. The possible ore at Red Flats is concentrated in the lateritic soil, whereas at Little Rocky Creek it is in the sulfide pods. Both types are surrounded by an area of relatively high nickel content. CHEMICAL ANALYSIS Chemical analyses of nickel were made by a di-methylglyoxime colorimetric test, similar to the standard test for nickel, utilizing concentrated sul-furic acid for extraction. The lower limit of detection for nickel in soil by the method used was about 10 ppm and for nickel in plants about 5 ppm. The relative deviation was about 25 pct. SOIL PROSPECTING General Statements: A summary of the approximate average parts per million of nickel in soil, as compiled from the literature and from my study, is given in Table I. Selected references are given at the end of the paper. Few of the investigators reported the type of extraction or analysis, so the data given may not be strictly comparable to mine, which were made with a sulfuric acid extraction. Any nickel concentration greater than these average values might be considered anomalous, although each area must be studied in relation to the surrounding rocks. Method of Soil Sampling: The soil samples were taken in a zone from 1 in. to 1 ft below the humus layer, and within a 15-ft radius around a station.

Jan 1, 1961

By J. C. Cook

In solution-mining of underground salt and similar minerals, using drilled wells for access, it is desirable to monitor the lateral growth pattern of the resulting fluid-filled cavern. Therefore, a process of seismic surveying from the surface of the ground has been conceived in which the amplitudes of waves reflected from and transmitted through the soluble formation are measured. The large acoustic impedance contrast between solid and fluid should produce striking amplitude anomalies, especially if shear waves are employed, since thick fluid bodies are opaque to shear waves. Horizontally-polarized (SH) shear waves are best for preventing conversion to P waves at the numerous horizontal interfaces in the ground. Field tests to date have shown that a truck-mounted, half-ton hammer striking horizontally against the end of a trench produces usable SH-wave energy at lateral distances up to about 850 ft. Horizontally-directed explosive wave sources were effective to about 2000 ft. Conventional magnetic-tape recording and processing were used, but with the detecting geophones oriented to favor SH waves. An irregular solution cavity in bedded salt at 500-ft depth has apparently been located by SH-wave and SV-wave reflections. Further field work is planned to corroborate and extend this result. The Brine Cavity Research Group, an association of 11 chemical and salt producing companies, is supporting this work. Major deposits of salt in tabular beds lie beneath some 300,000 sq miles of land in the central and northeastern U.S. This salt is a basic source of soda ash and chlorine, and has been extracted as brine from drilled wells for about a century. During the past two decades, the U.S. solution-mining industry, following the lead of European operators, has greatly improved the extraction process through the application of engineering and science.' In 1957, the Brine Cavity Research Group, an association of 11 chemical and salt producing companies, was formed. This group proceeded to attack certain common problems through the support of research. An outstanding problem has been that of determining the shape and location of the growing solution cavities in the underground salt, so that measures can be taken to maintain operating efficiency. The problem has been partially solved by the Dowel1 sonar mapping service, which employs a pulse-echo device lowered into the cavity through the well.2 However, the working range of this equipment is at present insufficient for large cavities, and echoes are not returned from highly sloping walls nor from behind such obstructions as rock debris. Therefore, an independent means of mapping the cavity, for example, from the surface without interfering with operation of the well, would be desirable. THEORY OF THE METHOD Seismic waves are the only physical agent known to be capable of sufficient resolution and penetration to define typical solution cavities from the surface of the ground. The geometry is unfavorable: cavity widths are generally less than half their depths below the surface; resolution and lateral location of boundaries and channels to within 50 ft at depths of 500 to 3000 ft is desirable. Conventional seismic surveying, as used for petroleum prospecting, is probably not the answer: isopach mapping, for example, is not thought accurate enough to define the cavity by the slight additional delay time it would introduce (of the order of 0.005 sec for a 50 ft-thick cavity in hard Paleozoic rocks). Refraction surveying has also been considered, but seismic specialists see little promise in it for this problem. In 1957, in correspondence with industry personnel, the writer suggested a seismic method based upon careful measurement of reflection amplitudes. As Table I illustrates, seismic reflection coefficients r for typical brine-rock interfaces are considerably higher than those for typical interfaces between different kinds of solid rock. This fact can be utilized in two ways, illustrated in Fig. 1: 1) If the cavity roof is reasonably flat (which it may sometimes be since the unsaturated top brine will be in contact with an insoluble rock stratum), extra-strong seismic reflections will be received from the salt stratum where the solid has been replaced by liquid.

Jan 1, 1964

By E. H. T. Whitten

Fundamental principles of trend surface analysis are briefly reviewed. Recent analyses of several granite masses illustrate the method of estimating the quantitative regional composition and also variation trends. Mineralogi-cal, bulk chemical, and other quantitative variates can be employed. Such results should improve gravimetric surveys (etc.) relying on correction terms based upon estimated rock composition. For the first time realistic estimates of the mean composition of rock bodies can be made with the aid of trend components. Deviation maps hold promise for delimitation of disseminated mineralized areas. Deviations comprise residual "anomalies" after removal of trend components. In petrogenetic work such deviations have been shown to reflect local influences (e.g., contamination of magma by assimilation of xenoliths or country rocks of the envelope). Similarly, mineralization should be reflected as deviations standing out from background trends. Actual examples are given. Present results largely involved projection of data onto a horizontal plane, but if sufficient data are available use of three spatial coordinates increases accuracy for prediction in "unexposed" areas. Regression analysis shows that statistical correlations between variates for regionally distributed specimens are often strong (particularly with percentage data). Hence, in preliminary surveys more easily determined variates may sometimes be employed to gain first estimates of the distribution of components more economically significant. The sampling plan is of paramount importance. Unless a suitable sampling plan is devised and adhered to rigorously during collection of the samples, all subsequent analysis is liable to strong bias and to yield spurious estimates of the truth. For a wide variety of purposes it is becoming necessary to assess the quantitative composition and variability of rock masses and mineralized zones of various types. In petrology and petrography this is something of a break with tradition, because virtually all descriptions heretofore have been qualitative. Although vast amounts of qualitative data have been compiled, little is known about the quantitative behavior of rock components. However, if variability of rocks could be understood and expressed with sufficient accuracy, there would be considerable advantage to both economic and petrogenetic problems. For example, if, on the basis of a limited series of observations, the three-dimensional geometry of a disseminated orebody (or ore-bearing formation) could be predicted accurately, it would be possible to extrapolate with confidence the structure into unexposed areas. The following example based upon the geometry of an igneous cone sheet illustrates the point. The significant rock-unit gives outcrops at a number of points on the exposed surface ABCD (Fig. 1A). Study of n exposures may enable a geologist to predict that the rock-unit is circular in form and thus indicate where the unit can be expected in unexposed terrain. Such observations are made at sites with u, v coordinates, but, if subsurface information is available at sites with uvw coordinates, it will eventually become possible to predict accurately the three-dimensional form of the rock mass. Geologic rock masses or mineral deposits are not generally as regular and symmetrical in geometric form as the body illustrated in Fig. 1A. However, even where the broad limits of a major rock mass are known, a more acute problem arises in attempting to obtain detailed quantitative estimates of its internal variability; it is difficult to predict the variability of a mass from a limited number of observa-

Jan 1, 1961

By H. Linder, W. H. Dennen

The graphitic carbon content of soils may be used to detect and delimit subsurface graphitic zones. Spectrographic measurement of carbon in C horizon soils from several areas in the northeastern United States shows good correlation with known graphitic bodies. Bodies of graphite and sulfides are readily located by electromagnetic prospecting methods, but these methods cannot generally discriminate between them. Usual practice, therefore, requires follow-up work on electrically anomalous areas by trenching, drilling, or soil sampling in order to determine the mineralogical nature of the conductor. The efficiency and cost of such follow-up is consequently an important factor in prospecting. The presence of buried sulfide deposits is often reflected in concentrations of metals in the superincumbent soil. Simple chemical tests for such metal concentrations have been developed and applied with considerable success. Bodies of graphite or mixtures of graphite and sulfides are, however, very common and a means whereby buried graphite could be detected by soil testing should provide valuable additional information in the search for ore sulfide and graphite deposits. Graphite is a notably stable substance and should persist in soil above graphite-rich horizons. Microscopic examination of soil samples high in carbon, however, failed to reveal any recognizable graphite fragments indicating a grain size in the clay range. Presumably such small particles would have some mobility in a soil by a translocation mechanism similar to that proposed for the movement of clay particles in a soil profile. Experimental data supports this idea since the boundary between background and anomalous soils carbon values is quite sharp, but the anomalous zone is slightly broader than the graphitic source rock. A simple spectrochemical technique for the determination of carbon in geological materials has been described by Dennen,1 and may be directly applied to soils. A modification of this technique which employs an arcing chamber through which nitrogen is passed is recommended to decrease contributions from atmospheric carbon dioxide. Tests indicate that soils over graphitic zones may be strongly enriched in carbon. The spectrochemical determination of carbon depends upon the formation of the cyanogen molecule (CN) from carbon in a sample and atmospheric nitrogen, under the high temperatures associated with a dc arc. Samples for analysis are dried, lumps broken, and screened. A small portion of the -100 mesh fraction is packed into a copper electrode and excited as the cathode of a dc arc. The band spectra of cyanogen are recorded photographically and the density of the bandhead CN 3883A is measured. The limit of detection of the method is about 0.01 pct C and its coefficient of variation is about 15 pct. Soils, of course, contain carbon in other forms than graphite, and the amount of interference from such sources was examined. The C horizon of several soils from Massachusetts, Maine, and Pennsylvania were found to have a carbon content of 0.3 to 0.5 pct by weight. This content is chiefly due to the presence of carbonates and vegetable matter in the sample and may be readily eliminated, or at least

Jan 1, 1961

By T. S. Lovering

The use of geothermal energy is expanding very rapidly. This type of energy has proven commercially profitable for generation of electricity, for space heating, process heating, auxiliary heating of water in conventional steam power plants and for recovery of chemicals contained in natural hot water and steam. Two types of geothermal energy sources are recognized: 1) hot springs in regions of nearly normal heat flow that tap a deep reservoir through which water moves slowly to a hot springs conduit and then rapidly to the surface; 2) hyperthermal areas in which the water is heated by a relatively concentrated heat source related to volcanicity. If there is a geologic trap that provides a geologic analog to a steam boiler, as at Larderello, Italy, the hyperthermal area will have a convecting system that develops superheated water at relatively shallow depth and may provide natural steam in large quantities. If a hyperthermal area is to be productive for a long time, the underflow into the reservoir should be slow enough to allow the heat source and convective system to heat the underflow to the working temperature, and the production rate must not exceed this rate of underflow. A model based on a typical aquifer suggests that the rate of movement of water through the reservoir be such that a few years are spent in transit between isotherms that are spaced about 2°F apart. The possibility of finding blind geothermal areas is illustrated by discussion of the techniques developed in evaluating the subsurface temperatures in the East Tintic district of Utah where a map of isotherms at water level (2000 to 2000 ft below the surface) shows that a hyperthermal area may exist a short distance southeast of the mining district. Very nearly all of the energy that man currently uses comes ultimately from the sun's radiation. This includes water power, fuels such as wood, peat, coal and petroleum, the wind and all our animal power. In the paper summarizing a conference on solar energyl6 the average amount of solar energy received daily on the earth is taken at about 1 cal per m2 per min or slightly less than 2 pcal per cm2 per sec; this is almost exactly the amount of energy on the average that the earth liberates in regions of normal geothermal gradient due to its own internal heating. In many places, however, the energy released is many times the average and in some of these hyperthermal areas, geothermal steam is used for generation of electricity, and hot springs are used for heating buildings and private dwellings, process heating, auxiliary heating of water in conventional steam power plants, and chemicals may be recoverable from both hot water and steam. The use of hot springs waters for heating houses goes back hundreds of years but until recently was confined to a few dwellings close to the hot springs. In Korea, some houses had hot spring water channeled through conduits in the floor centuries ago and thus the Koreans can be credited with pioneer development of radiant heating. In Iceland at present nearly a third of the population uses natural thermal water for domestic heating." The Reykjavik system pipes hot spring water at about 94°C throughout the city and has devised insulated double pipes that allow the water to be piped for some 25 km with a drop of only 1°C for every 5 km. The actual cost to the Icelandic consumer is only one-third the cost of heating by imported coal and yet the industry is one of the most profitable in Iceland. The most profitable use of geothermal energy has been its conversion into electricity which can be transmitted economically much greater distances than hot water. The largest installation at the present time is that at Larderello, Italy, where the Count of Larderello began to experiment in the production of electricity from geothermal steam 60 years ago — in 1904. He installed his first steam turbine, with a capacity of only 250 kw, in 1912 as the result of a local quarrel with the power company which furnished the current required in the Larderello chemical industry - an industry that then dated back nearly a century. As experience was gained in drilling deep holes to tap geothermal steam and in converting it to electric power, the capacity of the installation of Larderello gradually increased, but was all destroyed by the Germans during their retreat from Italy in the closing

Jan 1, 1965

By Z. F. Danes

Combination of gravity data and density logs makes it possible to determine the structural relief. Under a wide class of geologic conditions, the solution is unique, or limited to a single parametric system of solutions. As a useful byproduct, the method yields a new way to construct derivative maps, continue the field up or down, subtract regional anomalies, and perform smoothing. In the past, the problem of interpreting gravity anomalies in terms of structural geology was solved along two main lines: 1) A body of a certain shape and density contrast was assumed and the corresponding gravity anomaly calculated, analytically for simple bodies, graphically and/or numerically for more complex ones; then the computed anomaly was compared with the observed one, and the assumed shape corrected according to the differences between the two. 2) The anomaly is assumed to come from a warped interface between two media of different density; the relief of the warping is assumed small compared to the depth of burial, so that the structure can be approximated by a flat horizontal surface of variable density distribution. The first method is a standard technique, described in every text book on applied geophysics, and is well applicable, for bodies with predominant vertical dimension. The second one, probably first used by Tsuboi and Fuchida,' is mathematically more elegant. It applies to the fashionable field of integral transforms (Bullard and Cooper, 2 Tomoda and Aki, 3 Dean 4) and is useful mainly in cases when the vertical relief of the structures is comparatively small. 30th methods, tacitly or openly, assume a density discontinuity across the boundary of the two media, while within each medium the density is constant. However, the recent invention of the gamma-gamma

Jan 1, 1962

By A. W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall, for oreshoots mined were more continuous than drilling indicated. The Geophysics Dept of Michigan Technological University developed a portable induced polarization drill hole probe with a 3-electrode configuration and a sampling radius of 5 ft ±. A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec intervals and readings are taken every 2 ft. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the 1P potential is sampled for 10 ms and recorded. Resistivity (ohm-ft) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous S values noted. The low resistivity amygdaloid contains sills of high resistivity basalt. Verified by core logs, contacts between amygdaloid and basalt could be picked to ± 0.5 ft from resistivity alone. Lithologic logs of long-steel holes, based on resistivity, then replaced sludge logging. An S value of 30 mv/v was established as the lower limit of diagnostic 1P effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found. During the past ten years, the Calumet Div. of Calumet &Hecla, Inc has conducted extensive exploration and mining in the footwall of the Osceola amygdaloid lode in the native copper district in Michigan's Upper Peninsula. In an attempt to delineate more clearly the extent and nature of high-grade footwall copper mineralization, 876 diamond drill and long steel holes aggregating slightly more than 47,000 ft have thus far been drilled from the accessible hanging-wall workings in the Osceola No. 6, 13, 14 and 15 shafts. Early in this program it became obvious, through inspection of footwall workings in progress, that due to the erratic and bunchy occurrence of the native copper in the footwall zone, the exploration drilling was failing to outline completely the extent of the oreshoots. Early drilling re-

Jan 1, 1964

By A. A. Brant

In this presentation, concepts of the formation and evolution of the universe, the earth, and the cyclic civilizations of man are broadly outlined. The 5 billion or more years of the universe and the 4% billion years of the earth are contrasted to the 5000 years of modern society and the 100 years of objective scientific breakthrough. THE UNIVERSE Let us start back as far as possible, to the beginnings of this universe, some 5 billion or more years ago. This is a time interval that can be crudely underestimated by the moon-earth tidal friction effects that have increased the length of the day by about 1/1000 second per century — from a 5 to 7 hour day to its present 24 — and have moved the moon away at 5 inches per year to its present 240,000 miles. The oldest stony meteorites from interplanetary space give an age dating of some 4.6 billion years, approximating the time of formation of our earth. Further, certain stars pulsate, the period of pulsation being related to their absolute brightness. Measuring apparent brightness and comparing, gives the distance away. Thus Hubble and Shapley of Harvard, from 1925 on, were able to show that the universe reached as far as our telescopes could scan. The Doppler shift of the hydrogen red lines could only mean that the nebulae, or galaxies, were moving away away at velocities increasing with their distances, by 180 km/sec velocity increase for every million light year's distance. In short, the universe is expanding like an exploded bomb. Comparing the velocity increase per million light year's distance again indicates a zero time of some 5 billion years' Thus it appears that this universe had a finite beginning. Physical measurements and present theories permit some picture of our universe's birth. We know since Einstein that many forms of energy are equivalent, e.g., mass, and electromagnetic radiation, aspects of which are heat and light. Now with expansion, radiation density or equivalent mass decreases as a length factor to the 4th power, while mass as matter decreases at a length factor cubed. The temperature in outer space is now perhaps 100° absolute and the radiation mass equivalent is but 1/1000 the rarefied interstellar gas densities. Decompressing the universe to a starting point, however, raises temperature more rapidly than mass density, and results in a high radiation mass energy fraction, which since it is proportional to temperature to the 4th power suggests a zero point temperature of several billion degrees, brighter than any sun. "Let there be light and there was light," according to Genesis 1-3. Now what further initial conditions must there be to explain the relative abundance of the elements in the universe, which by spectral analyses of the earth's crust, stony meteorites, and the sun and stars is surprisingly uniform throughout. Some 55% of all cosmic matter is hydrogen, some 44% is helium and only 1% is made up of all the heavier elements in much the same proportions as on earth. These latter decrease logarithmically in abundance up to atomic weight 100, then level out. This consistent abundance distribution of elements in the universe may be generally explained by taking at Time Zero a hot neutron gas of density about 10-3 grams per cc, at a temperature of several billion degrees Centigrade, with a high radiation energy fraction. Generally neutrons break down into positrons and electrons within about ten minutes, but at the initial high temperature and radiation pressure would recom-bine. However, with rapid expansion and decrease of temperature and pressure, the neutron disintegration would run uncompensated and aggregation would result from neutrons and protons uniting in different degrees of complexity. The total calculated element aggregation time would be about one hour while the temperature still remained above one billion degrees. The element abundances formed would depend on density of the nuclear gas, simplicity of the atom formed, and the neutron capture cross section. Thus a higher density

Jan 1, 1964

By John B. Gustavson

The mineral deposits found in carbonate facies rocks of sedimentary basins include deposits comprised of the country rock itself such as limestone for chemical uses, dolomite for road aggregate, and a variety of other industrial uses of the sedimentary rock. Exploration for new reserves is generally conducted on basis of outcrop investigation, subsurface drilling, and facies change studies while geophysics and geochemistry are not applied. In contrast, rapid development has taken place in the application of both geophysical and geochemical techniques in exploration for stratiform deposits of zinc, lead, barite, and fluorite deposits. This paper will present case histories and show illustrations from such work in the Mid-Continent region. The Metals Division of International Oil & Gas, Inc. has gathered this experience through work over the last three years along the southern margin of the Eastern Interior platform focusing on the states of Arkansas and Tennessee. The exploration work was conducted partially for the Company's own account, partially in joint exploration ventures with mining companies including International Mogul Mines, Ltd., a Canadian company; Bear Creek Mining Company, a subsidiary of Kennecott Copper Corporation; the Mining Division of W. R. Grace and Company, and Boliden-Preussag Exploration, a Swedish-German partnership. We wish to take this opportunity to thank our venture partners for allowing presentation of the various sections of this paper.

Jan 1, 1976

By Harold M. Mooney

The most significant trends appear to be an increased use of electromagnetic and geochemical methods. The most promising instrumental developments are airborne electromagnetic equipment, a magnetometer based on nuclear resonance, and reflection seismic equipment operable to depths less than 100 ft. Work in progress may lead to a one-man magnetometer capable of high precision and continuous recording.

Jan 3, 1955

By Jr. Matthews

The Candelaria copper-gold deposit is located in Region m of Chile, 805 kilometers north of the capital, Santiago. Candelaria was discovered in 1987, following a six month exploration program. In late 1986, induced polarization (IP) surveys outlined an anomalously high response within the area of interest. The first test hole bad three intersections totaling 49 meters, with an average grade of 1.97% copper. Drilling eventually outlined approximately 390 million tonnes, grading 1.09010 copper and 0.26 grams/tonne gold. Production began in early 1995 and is estimated at 120,000 tonnes copper and 80,000 ounces gold annually.

Jan 1, 1996