Search Documents

By John Parianos

"Seafloor mining provides significant potential economic benefits for many Pacific nations that may be “land poor” but “coastline rich,” meaning they have the potential to utilize and profit from the mineral wealth within their Exclusive Economic Zones that extend 200 nautical miles (360 km) out from their coastlines. Within international waters, mineral wealth is the “Common Heritage of Mankind” with additional benefits for sponsoring states and their people.The Solwara 1 Project build continues with significant progress over the last twelve months. The Seafloor Production Tools (SPTs), Subsea Slurry Lift Pump, riser pipe, launch and recovery systems and winches are now complete with delivery to test facilities and the vessel ongoing. Recent focus has been on submerged trials for the SPTs, but the vessel build continues to progress to schedule. Nautilus appreciates the great support thus far from our all our stakeholders.Our focus is to develop the world's first commercial high grade seafloor copper-gold project in an environmentally and socially responsible manner and to launch the deepwater seafloor resource production industry.Nautilus’s marine research continues, including a 3.5-month series of exploration cruises for Seafloor Massive Sulphides in the Bismarck Sea, as well as fabrication of purpose designed exploration equipment."

Jan 1, 2017

By A. R. Khodabandeh, T. Nematkhah

Correct selection of forging parameters is very important to produce sound superalloy parts. In this investigation nickel-iron base superalloy IN901 successfully forged and seal spacer, which is a part of airplane with about 11 kg weight has been produced. Forging has been performed on the basis of hot compression results, which show deformation above 1100°C associated with dynamic recrystallization (DRX) which can increase the workability of material. On the other hand annealing at 1100°C decreases the flow stress during hot compression, and then increases the material formability. Then billets annealed at 1100°C in electrical furnace for 24 hours and reheated again to 1100°C before forging. Initial square cross section billet with 128mm side and 202mm length forged immediately after reheating by 80MN mechanical press. Specimens forged in five steps: upsetting, three steps molding and finishing. Preformed and molded specimens reheated in electrical furnace before later step of forming. Finally specimens trimmed by 1 OMn mechanical press and hot set by hydraulic press and then cooled in air to room temperature. Results show that reheating temperatures has been selected correctly because there isn't any surface crack and die cavities filled completely by forging material. Material flow has been carried out properly and there isn't any defect in critical points especially in extradoses and intradoses. Microstructural examinations show that grain boundaries contain Ti-rich globular particles that formed during cooling.

Jan 1, 2006

By Bin Du

In recent years, concurrent product design and process is gaining popularity and will become a norm of the industry of the future. Forging has been a critical manufacturing process for production of components with superior tensile strength, toughness and grain flow. This paper describes an expen system which is being developed for forging die design and forging process analysis in concurrent engineering environment. Rules and guidelines pertaining to forgeability are formulated and incorporated into the knowledge-base in building the system. The system is built using an object-oriented paradigm. The object-oriented approach and hierarchical rule structure paradigm are briefly discussed. Finite element analysis packages (ALPID-2D) were incorporated into the program to give the simulation result of the forging process. The system can automatically produce a competent design and recommend a set of processing parameters for a given product. The designer can modify the design according to the result of the simulation.

Jan 1, 1992

By F. E. Bash

IN recent years, there have been a number of experiments conducted to determine the rates of heating and cooling of various sizes and shapes of steel ingots. Up to date, however,-most of the published data has dealt with small sized ingots, the largest being an 18-in. (46 cm.) cube, the data on which was presented before the Iron and Steel Institute in May, 1918, by E. F. Law. It is due to thus lack of information on the rate at which large ingots absorb heat and come to temperature that the heating- practice varies so widely in different plants. One of the questions over which there is much debate is the proper rate of heating of large ingots for forging and the time actually required for the center of a mass of steel to come to forging temperature. As a continuation of experiments described by M. E. Leeds1 and at the request of Mr. G. R. Norton of the Sizer Forge Co. and Mr. R. C. Drinker of the Emergency Fleet Corpn., the test described in this paper was carried out on a 24-in. (61 cm.) round ingot and the rate of heating and cooling determined under regular production conditions. The ingot had been partly forged at one end but, on developing a flaw, had been scrapped so that it was available for test. The size and shape of the ingot and its position in the furnace are shown in Fig. 1.

Jan 9, 1919

LAWFORD H. FRY, Burnham, Pa. (written discussion*).-As a sup-plement to the information given by Mr. Bash, a diagram is submitted showing the results of a somewhat similar experiment carried out at the ordnance plant of the Standard Steel Works Co. In this case the ingot to be heated was a nickel-steel octagon ingot, weighing 14,700 lb. (6667 kg.). This ingot was to be forged into two 255-mm. howitzer jackets. A hole was bored half way of the length of the ingot, extending into the longitudinal axis, and a base-metal thermocouple inserted in this hole.

Jan 11, 1919

By Francesco Toschi

The Special Bar Quality family comprises a wide range of steel grades, mainly requested by the automotive, energy and engineering sectors, for applications where significant performances are required (eg. stresses, temperatures, working cycles, etc.). To meet these requirements it is necessary to reach a precise control of both the mechanical characteristics and metallurgy structures along the whole production chain. For semi-product with large dimensions, such as equivalent diameters around 300 mm, this is traditionally obtained through a manufacturing route which comprises the casting in ingots followed by reheating, forging and rolling. After 2010, new processes were investigated and technologies developed to replace the ingot route with a continuous casting followed by controlled high-reduction rolling. In these processes a seamless integration of CCM with rolling is implemented so to obtain the precise control of material flow, applied deformation and working temperatures. By using the proper combination of rolling diameter, speed and applied reduction, a very good control of the metallurgy structure across the whole section can be obtained, so to also remove the internal discontinuities ("voids") generated during the continuous casting. These processes, which can be defined "forging-like", are applicable to several grades also with large semi-product dimensions (300 mm and more). Besides, removing the ingot route means increased yield and productivity, which is very beneficial to the economical management of the plant. An example of this "forging-like" process is represented by the high-reduction blooming stand installed by Acciaierie Venete in the Padova-Camin mill. This article describes its main concepts as well as its technology and process features.

Oct 30, 2017

By Carlos G. Philips J.

El Banco Minero tiene la función de promover y fomentar la minería a través de la habilitación de sus préstamos a las grandes o pequeñas minerías. Sin embargo, muchos profesionales y mineros desconocen la mecánica de solicitar ayuda económica y técnica de dicha institución. En este sentido, el objeto del texto señala la forma adecuada de solicitar préstamos s la entidada bancaria. Para ello, se revisa la clasificación de los prestatarios sea en pequeña minería, mediana minería y gran minería, la cual no trabaja con el Banco. Asimismo se señala los documentos necesarios que deben ser presentados para la solicitud del banco (plazos, costos, comprobantes de depósito previo), asi como aquellos que faciliten el estudio técnico. Se evalúa también el depósito previo, las habilitaciones sobre minerales, garantías y la forma de financiación del proyecto.

Aug 20, 1965

By Jamie N. Burdeski, Susan E. Hartfield-Wünsch

Aluminum sheet use has been steadily increasing in the automotive industry to achieve mass reduction and improve fuel economy. One significant manufacturing challenge for aluminum sheet implementation is the reduced formability compared to the steel alloys it replaces. This paper includes friction results from the draw bead simulator (DBS), twist compression (TCT) and strip draw (SDT) tests, for two oil based lubricants and four hot melt lubricants. Formability testing was done with the same lubricants and materials, testing in pure stretch with a hemispherical punch, and in draw with a breadpan shaped die.

Jan 1, 2015

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, A. S. Kabir, R. Petrov

The recrystallization and texture evolution of AZ31 sheets obtained through two stages was investigated at different stages of post-rolling annealing. The specimens were rolled at the temperature of 100? and at a fast speed of 1000m/min and low speed of 15m/min with a reduction of 30% in one pass. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2015

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, Hara, A. S. Kabir, R. Petrov

Manufacturing of thin sheet is difficult in industries. Some approaches, such as small-draft multi-pass rolling, intermediate annealing, isothermal rolling and high-speed rolling were proposed to overcome the deformability. In this study, different rolling speeds from 15 to 1000 m/min were employed to twin rolled cast AZ31B magnesium alloy to different reductions. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2014

By Fernando Altamirano

El presente trabajo refiere la prevención de incendios en los campamentos mineros metalúrgicos a través de un programa de formación de brigadas. Los principales objetivos del programa son identificar los riesgos de incendio para asi corregir las condiciones inseguras mediante las inspecciones de rutina, aplicar los medios de control y extinción de fuegos de que disponga el minero y la educación al personal en la prevención de incendios para adiestrarlo en la respuesta inicial y calificada.

Oct 6, 1999

By Juan Manuel Ojeda Sarmiento

Los clusters como concentraciones geográficas de compañías interconectadas e instituciones dentro de una actividad particular. La interacción de estas organizaciones generan un clima de negocios que estimula la mejora en su desempeño, competitividad y rentabilidad de largo plazo. En ese sentido, el presente texto describe el cluster alpaquero como propuesta de desarrollo comunitario local para la provincia de Candarave - Tacna, que integra la producción primaria de fibra de alpaca, transformación en sombreros, peletería y textiles, y su comercialización en mercados regionales, nacionales y externos.

Sep 14, 2009

By Juan Manuel Ojeda Sarmiento

"El Proyecto de Estandarización de la Intervención Social en las Comunidades es una herramienta de gestión social, cuyo objetivo es sistematizar las buenas prácticas de relacionamiento comunitario aplicadas en la minería peruana, a través de la incorporación del concepto de desarrollo comunitario como su principal soporte. De esa manera, se facilitan las actividades de las empresas minero-energéticas en las comunidades de su entorno de influencia directa, durante sus principales fases: exploración, factibilidad, construcción del proyecto, operación y cierre. En esta perspectiva, el presente trabajo señala el concepto de las Relaciones Comunitarias en las industrias minero-energéticas, donde se presenta los objetivos de la estandarización de la intervención social en comunidades y se plantea nuevo enfoque de relaciones comunitarias, basado en la gerencia de actitudes y percepciones de los grupos de interés, ubicados en los ámbitos rural y urbano del entorno de influencia de la empresa, para lograr el consenso social. "

Sep 14, 2009

By Alcides Meléndez González

La formación profesional del personal minero es importante en tanto mejora su desempeño y responsabilidades con la empresa y actividad minero. En ese sentido, el presente trabajo describe los programas de educación profesional desarrollados por el Estado u organizaciones privadas a través de tres etapas: formación profesional elemental, formación profesional especializada y la formación profesional universitaria. Los principales objetivos son: adquirir los fundamentos técnicos, científicos y tecnológicos de la actividad minera y establecer mejores métodos de trabajo como nuevos procesos tecnológicos.

Nov 1, 1972

By Jorge Vargas Fernández

Con el objetivo de incrementar la productividad de la minería, se plantea la realización de una positiva acción nacional de formación y capacitación en todos los niveles de la industria minera a través de un análisis de la situación actual respecto de los mineros, ingenierios y técnicos. Por ello, el presente texto señala la descripción del sistema "B" en funcionamiento de la productividad minera y la tecnología adecuada a la realidad.

Nov 1, 1972

By M. Mustafa Kahraman, Sean Dessureault, W. Pratt Rogers

Most contemporary mines have considerable amounts of data. Structured and unstructured large data sets are colloquially named big data. Much of the data in mining operations come from a variety of systems, each with different databases and reporting environments. Standard technology deployments create a Bsilo-ification^ of data leading to poor system benefit. Through modern server monitoring and systematic approach, data utilization and value can quantifiably be measured. The Data Utilization and Value Index (DUVI) can quantify business intelligence best practices and user interaction. This study seeks to provide a data management tool to measure data utilization across the process of converting data into action.

This book has employed miners' narratives to illustrate basic concepts about the escape process. One of the most powerful means by which people make sense of their experiences is through the telling and internalization of stories [Bruner 1990]. By couching one's own and others' motives and actions in terms of a coherent narrative, a person is able to learn from mistakes and plan future behaviors that may help ensure survival. A growing body of research suggests that decision-making skills used to deal with emergency situations can be taught and assessed by simulations based on narratives from the real world [Bransford et al. 1986; Brecke 1982; Brener 1984; Connolly et al. 1989; Halff et al. 1986; Jones and Keith 1983; Lacefield and Cole 1986]. Such techniques have been used to address the decision-making of medical personnel, civil and military flight crews, and even people involved in broader life events such as political and military situations [Babbott and Halter 1983; Dugdale et al. 1982; Farrand et al. 1982; Gilbert 1975; McGuire 1985; McGuire et al. 1976; Flathers et al. 1982; Giffin and Rockwell 1984; Jensen 1982; Janis and Mann 1987]. Given the validity of this method of study and the promise it holds for helping people improve the quality of their responses to nonroutine occurrences, it is perhaps surprising that there have been no studies of emergency decision-making among blue-collar workers prior to those conducted by the present authors and their colleagues. The purpose of this chapter is to describe underground coal miners' decision-making performance on a table-top simulation whose problem structure is derived from interviews with a group of eight miners who escaped from the 5 Left section at Brownfield Mine. The exercise was constructed by a panel of domain experts (mine safety and rescue personnel) with the assistance of an educational psychologist. The simulation includes actual predicaments with wise and unwise decision alternatives that, in the opinion of these domain experts, are characteristic of such escapes. Results reported in this chapter are the scores of a sample of experienced mine workers who completed the simulation. Because the exercise is a series of objective performance tasks coupled with detailed and immediate feedback, this simulation can be used to teach and refresh critical escape skills, as well as to provide data concerning the proficiency of miners at the time of exercise administration.

Jan 1, 2000

By D Nourry

Optimising the blast is a major issue in the blasting business. It generally means acting on the blasting pattern (drilling, charging, detonating) in order to get a given æresultÆ. This result may either be related to economic reasons, such as the fragmentation influencing productivity, or technical reasons, for example vibrations and projections. Within the frame of the EEC funded Brite-Euram project entitled æBlast-ControlÆ, involving academic research and applied expertise, a general methodology was developed to approach such a problem and currently applied to the industrial partners of the project and final end-users of the generated results. These partners are the limestone ALZO quarry of the CALCINOR group in the north of Spain and the dolomite DMD (Dolomies-de-Marche-les-Dames) quarry of the LHOIST group in the east of Belgium. A first part of the project, over 18 months, was dedicated to establishing a clear relationship between productivity of operations from drilling to primary crushing and the fragmentation resulting from the blast. Extensive monitoring of blasting, production performance and fragmentation data was carried out and automatically collected into a database on both quarries. As expected, it appeared that excessive amounts of fines or boulders were substantially reducing productivity and thus profitability of the operation. Furthermore, an æoptimalÆ fragmentation was assessed for the quarries to run at the best (high throughput, low cost). The second and last part, for the remaining 18 months, was then dedicated to adapting the blasting practice in order to orientate the fragmentation towards a æbetterÆ one. A very common problem normally addressed by any consultant. Nevertheless, the target was not limited to solving the problem for these two quarries, but also to develop a generic method to address this blasting adaptation process and to implement it into a computerised tool. At this stage, it is then obvious that portability of the method and the system are major qualities to be looked for. This paper is aimed to present how this method was developed, how the system was implemented and how it was finally used.

Jan 1, 2001

By José Calderón

Frente a la ausencia del Estado en el distrito de Pataz (La Libertad, Perú) —donde Poderosa tiene sus operaciones— existe una presión por parte de la población hacia la empresa para cubrir el déficit de agua de consumo humano. Por ello, se implementó un proyecto, con los anexos de Pueblo Nuevo, Zarumilla y Chuquitambo como ámbito de acción, cuyo objetivo principal era la formalización de la gestión de agua de consumo poblacional, de tal manera que la población disponga de agua de calidad, a la vez que se prevenga y reduzca la conflictividad socioambiental. En el presente documento se exponen las principales actividades realizadas como parte del proyecto, así como los resultados obtenidos.

Sep 20, 2019

By Pedro Hugo Tumialán de la Cruz

La distribución espacial de los minerales como efecto a ciertas condiciones físicas y geológicas del terreno se conoce como zoneamiento. El conocimiento de este proceso permitirá la planificación de un programa de exploración para una futura explotación. En este sentido, el presente texto señala las formas geométricas de zonamiento encontradas en los yacimientos hidrotermales del Perú a través del empleo de diversos métodos geológicos como el método de distribución minerológica, isovalores de leyes, cocientes métalicos, así como el método de trazas en casos especiales.

Nov 20, 1978