Search Documents

By N. Patel

Many factors, from engineering and design to supply, installation, and operation affect the service lifespan of cast refractory linings. If a shortcoming occurs at any of these stages, the lining lifespan can be drastically reduced. Although not every aspect that can affect a cast refractory lining?s lifespan is outlined here, a few key points are highlighted, with an emphasis on the various installation parameters. Keywords cast linings, refractory lifespan, lining engineering and design, lining supply, lining installation, curing, dry-out.

Aug 1, 2013

The U.S. Code of Federal Regulations (Title 30) requires that a methane monitor be placed on every mining machine to continuously observe and record methane levels at the face. The monitor must provide a warning whenever methane levels are 1.0 percent or higher. An effective monitoring system will indicate a methane concentration of 1.0 percent on the mining machine before methane levels at the mining face reach 5.0 percent. Where the methane monitor is located on the mining machine is one of the most important factors that determines how effectively face methane levels can be predicted. Any change in the sampling location will result in a change in measured methane concentration. To protect the methanometer, it is usually located on the cutting boom at least 1 to 1.8 m (3 to 6 ft) outby the front cutting bits. A face ventilation system using blowing tubing was simulated in a full-scale test facility. Methane released from the face area was monitored at multiple locations on a model mining machine as well as locations near the face. Based on the relationship between concentrations measured on the machine and at the face, criteria were developed for selecting the best machine locations for monitoring methane. Recommendations are given for revising methane action levels for alternative sampling locations.

By J. M. Wempen

Booster fans in underground coal mines are often located using the concept of a neutral point. Normally, intake airways are maintained at higher absolute pressure than return airways; therefore, air leaks from intake to return. By adding a significant pressure force to a region of a ventilation system, booster fans installed in a return airway can increase the pressure in the return so that air leaks from return to intake. This is commonly referred to as recirculation. The neutral point occurs at the location in the system where the pressure difference between [ ] the intake and the return airway is zero. At this point, there is no leakage or recirculation. Ideally, placing a booster fan near the neutral point minimizes leakage and recirculation. However, in practice, the position of the neutral point is not static and it changes as the ventilation system parameters change. Booster fans have the potential to increase the capacity and efficiency of coal mine ventilation systems. However, these fans add a significant pressure source to ventilation systems and can create areas where the pressure in the intake is less than the pressure in the return causing recirculation. In systems with multiple booster fans, there may be multiple recirculation paths and, as the capacity of these fans increases, recirculation is more likely to occur.

Jan 1, 2012

By J. M. Wempen

Booster fans in underground coal mines are often located using the concept of a neutral point. Normally, intake airways are maintained at higher absolute pressure than return airways, so air leaks from intake to return. By adding a significant pressure force to a region of a ventilation system, booster fans installed in a return airway can increase the pressure in the return so that air leaks from return to intake. This is commonly referred to as recirculation. The neutral point occurs at the location in the system where the pressure difference between the intake and the return airway(s) is zero and at this point there is no leakage or recirculation. Ideally, placing a booster fan near the neutral point minimizes leakage and recirculation; however, in practice the position of the neutral point is not static and it changes as the ventilation system parameters change. This paper presents a study of how changes in the system parameters affect the location of the neutral point in a model coal mine ventilation system. First the effects of booster fan pressure and location on the neutral point are evaluated. Next the effect of increasing mine distance, and therefore mine resistance, on the location of the neutral point and the magnitude of recirculation is evaluated.

Jan 1, 2012

By J. F. Morrison, C. H. Wyndham, N. B. Strydom

INTRODUCTION The shovelling of rock in stopes is still a basic and important operation in many gold mines in the removal of gold-bearing rock from the stopes. There is, however, little factual knowledge of the factors which influence the the rates of energy expenditure and work output, and of the way in which variations in these factors, individually or in combination, affect the mechanical efficiency of the mine workers. What for example is the influence of different rates of shovelling, shovel loads and distances of throw? How does stope width and dip of the stope affect the mechanical efficiency of men shovelling rock? Recently a simple physiological test was introduced into the gold mining industry for classifying Bantu recruits into those capable of hard, moderate and light work. If this test is used to select only those Bantu mine workers who are capable of hard work for the task of shovelling rock in stopes then the rate of energy expenditure which could be expected from these men is 1.5 litres/min for the entire period of the shift. With an adequate knowledge of the influence of the various factors which affect the rate of energy expenditure of men shovelling rock in stopes it would be possible to set work standards for Bantu mine workers in stopes. This should be done in terms of the rate of shovelling, the shovel load and the distance of throw for any combination of width of stope, dip of stope, condition of foot wall and grade of rock in such a way that the resultant energy expenditure would be the 'optimum' that could be expected from the men but would be within their capacities for physical work of an endurance nature (that is, 1. 5 litres/min from the 'average' Bantu mine worker). Work standards could thereby be determined for the different stopes of a mine on a sound and systematic basis. In order to supply the information required a study was carried out by the Human Sciences Laboratory in which the work output and energy expenditures (in terms of oxygen consumption in litres/min) were measured on six highly trained Bantu mine workers under the following conditions: (a) rates of shovelling of 3, 4, 5, 6, and 10 shovels per minute. (b) loads of from 9 to 18 lb on the shovel. (c) distances of throw from 8 to 20 ft. (d) stope width of 28 in., 42 in. and 72 in. (e) dip of stopes of 0°, 15° and 30°. (f) rough and smooth footwalls and various grades of rock size. This paper gives the main results of practical importance of this study. Method The experiments were designed and conducted in conjunction with the Work Study Department of one certain underground conditions such as variable stope widths, stope angle, etc., were made available in a mine Surface Training School and suitable subjects were selected from the large number of labourers being put through the training school. Subjects Bantu recruits who had returned to the mine for a new contract and who had previous underground experience on shovelling were considered to be suitable as subjects for the experiments. The particulars of the subjects are given in Table I. TABLE I PHYSICAL CHARACTERISTICS OF SUBJECTS Weight Height Surface area Max O2 capacity Subject (Kg) (cm) (sq meters) (Litre/minute) A 71.5 167.3 1.80 3.5 B 61.5 162.3 1.65 2.8 C 63.0 164.1 1.69 2.4 D 66.5 167.4 1.75 2.8 E 70.2 164.6 1.77 3.0 F 77.8 173.1 1.92 3.8 Training The method of shovelling, accepted by the Work Study Department, was demonstrated to the subjects who then practised the movements with empty shovels, under the supervision of an instructor. After the technique was mastered, the men started shovelling rock and were trained for at least four hours per day to work at the higher shovelling rates. Training was continued for three weeks to enable the subjects to achieve a reasonable degree of physical training and conditioning. Shovelling method In both the kneeling and standing positions the subjects faced the pile of rock, grasped the shovel in the accepted manner and pushed the blade of the shovel into the base of the pile of rock, sliding the blade between the rock and the concrete floor. In the standing position (72 in. wide stope) the back leg assisted in the movement by pushing the knee against the back of the hand holding the shovel handle. In the kneeling position the elbow was tucked into the side of the body so that the muscles of

By J. H. Viljoen, A. Heyns, J. F. Morrison, C. H. Wyndham, N. B. Strydom

Discussion M. J. Martinson* (Associate Member): This is another interesting paper in the series which the Human Sciences Laboratory is publishing on the physiological cost of the more strenuous manual tasks performed underground. As a mining engineer-albeit presently an academic one -this contributor is more concerned with the practical significance of the study in the field of stope cleaning than with physiological niceties, but before discussing some of the practical issues raised by the paper perhaps the authors would care to reply to lay comment on three physiological matters. Firstly, in two places the authors make statements to the effect that the maximum oxygen intake of 'average' (sic) Bantu mine workers is 3.0 l/min. What do the authors mean by 'average'? Maximum oxygen intake in the individual is probably some function of inter alia age, physical fitness, state of health, ambient partial pressure of oxygen, diurnal and/or seasonal changes in metabolism, and possibly cumulative exposure to dust and other occupational contaminants. Since maximum oxygen intake is apparently such an important quality in manual labourers we ought to have a clear picture of its distribution in the entire labour force, and also know precisely how the individual's quantum is affected by factors such as those mentioned above. Secondly, arising out of the same statements and ignoring the reservation implicit in the previous paragraph, is it correct to say that the 'average' Bantu mine worker has a maximum intake of 3.0 l/min? In the August 1966 issue of the South African Journal of Science four of the present co-authors reported the mean maximum oxygen intake of a random sample of 338 Bantu recruits of different tribes to be 2.63 l/min with a standard deviation of 0.542 l/min, and these figures were repeated in a paper published in the November 1968 issue of this Journal. Admittedly the mean maximum oxygen intake of the six subjects used in the present study was 3.05 l/min, but since they were selected on the grounds of previous shovelling experience they can hardly be regarded as being 'average' recruits. Thirdly, it seems to me that the authors are perhaps a little uncritical in their acceptance of the '50 per cent of maximum oxygen intake' level of activity for endurance work. I am not unmindful of the evidence upon which this level is based, but I suggest that the evidence is at best tenuous and that the whole topic of fatigue and 'optimum' levels of productivity under conditions of high muscular activity and considerable psychological stress is a lot more complicated than would appear from the authors' ready acceptance of the 50 per cent level. Under present working conditions the question is largely rhetorical because it would need an army of supervisors to ensure that all members of a typical gang work at 'optimum' levels throughout the shift, but if individual performance should ever become more readily determinable the issue might become crucial to management and malayisha alike. So much for physiological matters; now a few random thoughts on some wider, practical issues raised by the paper. In the paragraph headed Material the statement is made that 'The mixture (of fine, medium-sized and bigger rocks) was considered to be representative of an average underground rock sample'. Elsewhere in the report the authors specifically draw attention to the effect of particle size on the oxygen consumption of men shovelling graded material, and intuitively one imagines that the size distribution of the material being shovelled would be highly significant in a study such as this. Presumably the authors were forced to assess size distribution subjectively because of the lack of objective data on the subject, and possibly the necessity for this assumption highlights how little we know quantitatively about any of the variables in stope cleaning systems. In this connection it may be remarked that although the present study was largely designed to show how dip and stoping width effect energy expenditure in shovelling, no data are given-nor, probably, are they available-to show how the industry's stoping tonnage is distributed in terms of these two factors. It seems to me that if the mining industry seriously hopes to improve stope productivity it must start by measuring the basic variables in existing systems. Elaborating somewhat on the previous paragraph, there also seems to be a tremendous gap between the present study-and its predecessors-and the prospect of gainfully using the information so carefully garnered by the authors. It would be reassuring to hear from the authors that their work on the physiological aspects is being integrated in some master plan for increasing productivity of manual labour. This I fear is not the case, and if productivity has changed at all in recent years I would hazard a guess that the change has been brought about by random factors rather than by systematic engineering design. The Human Sciences Laboratory has worked extensively in stopes in the past, and possibly the time has come when it should widen the ambit of its operations to include engineering-type analyses of cleaning systems, with particular emphasis on the economics of rapid cleaning by manual labour. Perhaps experiments could be conducted with stakhanovite-type gangs consisting of men selected for their high maximum oxygen intake and superior motivation; these men might be offered special incentives in the shape of extra pay

Jan 10, 1969

By Stephen R. Pogorski, Nicholas Busigin, Colin R. Phillips

The movement of radon away from its source in porous media is determined by two key parameters: the fraction of the total radon formed which enters the intergranular pore spaces, termed the emanation coefficient, and the transport processes which exist in these pores such as diffusion and convection. The first parameter, the emanation coefficient, is of primary importance since it is a measure of the actual amount of radon which is free to migrate within the media. The effects of particle size and radium concentration on the emanation coefficient were examined using a quartz-pebble conglomerate ore from the Elliot Lake mining district of Ontario. It was found that the smallest particle size examined (<74 µm) had the highest radium concentration and contributed the most to the radon emanation. A one-to-one correspondence between radium concentrations for the various particle size fractions and radon emanation was not observed. Samples were examined using scanning electron microscopy and very small particulates were observed to be present on the particle surfaces. When these very small particulates were removed from the host particle surfaces by rinsing, the radon emanation decreased by a factor of 17. This result indicates that most of the emanation comes from the very small particles. The effect of moisture on the emanation coefficient was examined qualitatively and a trend of increased radon release with moisture content was noted.

Jan 1, 1981

The authors are looking at the behaviour of the mineral processing circuits by means of the simulators operating under random disturbance. The present paper deals with the fuzzy control systems in comparison with PID controllers. A series of tests are conducted on simplified prototype processes with (1) dead time plus first-order lag model and (2) diffusive model. In the next series of tests the self-sustained process model was introduced to improve control against dead time. In both cases fuzzy and PID controllers are optimised by EVOP method. Particular attention is paid to the effect of observation noise to analyse for the problems which can be fatal to practical applications in mineral processing. Finally the methods developed are applied to a closed-circuit wet grinding system simulator operating under random disturbance.

Jan 1, 1993

By L. M. Wang, G. P. Jiang, Y. Jiang, Liao. W. S.

ABSTRACT The authors measured porosities and permeabilities for cores from a low-permeability sandstone uranium deposit in Inner Mongolia. Features studied included fine pore structure, mineral composition, cation exchange capacity, granule appearance, and cementing features. In general, grading of the grains was relatively poor, which decreased the radii of the pore channels. The pore throat distribution was significantly heterogeneous. Pore channels ranged from small to large, but the lack of large pore channels led to low permeability. Cementation by calcite and clays, including montmorillonite, chlorite, and kaolinite, resulted in pore channel narrowing, further decreasing the permeability of the formation.

Jan 1, 2014

By T. B. Braun

Cathode contamination is the principal factor affecting the quality of electrorefined copper. It is commonly accepted that annealability is unfavorably affected by the following elements, in decreasing order of adverse effect: tellurium, selenium, bismuth, antimony, and arsenic. Silver in cathodes has importance as it represents a nonrecoverable loss of silver to the refinery. Mechanisms for the contamination of cathodes by these elements are examined and the effect of operating variables on contamination, including anode composition, electrolyte composition, electrolyte temperature, addition agent practice, and electrolyte discard rate, are discussed.

Jan 1, 1976

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

By Gabriel Riveros

Fire refining of copper consists of two stages copper oxidation and copper reduction. Very frequently the capacity of the anode furnace is determined by the rate of copper reduction. The analysis of factors affecting the rate of the oxygen reduction from a liquid copper with solid carbon or injected hydrocarbons pointed out the role of the mass transfer in a liquid copper in final stage of the reduction. Experimental results of copper reduction with graphite and injected natural gas in laboratory- scale crucibles showed two stages of the reduction process with a sharp change of the controlling mechanism. The estimated dynamic surface area of gas bubbles based on the measured bubble frequency and the gas flowrate allowed for the detennination of the reaction constant as a degree of the partial pre-combustion of the air/natural gas mix. The variation of the used reductant as a function of the oxygen concentration and temperature has been evaluated based on the detennined kinetic model. The intensification of copper reduction in fire refining has been discusses on the basis of obtained kinetic data and analysis of various factors detennining the time of reduction.

Jan 1, 2003

By Gabriel Riveros

Fire refining of copper consists of two stages copper oxidation and copper reduction. Very frequently the capacity of the anode furnace is determined by the rate of copper reduction, The analysis of factors affecting the rate of the oxygen reduction from a liquid copper with solid carbon or injected hydrocarbons pointed out the role of the mass transfer in a liquid copper in final stage of the reduction. Experimental results of copper reduction with graphite and injected natural gas in laboratory-scale crucibles showed two stages of the reduction process with a sharp change of the controlling mechanism. The estimated dynamic surface area of gas bubbles based on the measured bubble frequency and the gas flowrate allowed for the determination of the reaction constant as a degree of the partial pre-combustion of the air/natural gas mix. The variation of the used reductant as a function of the oxygen concentration and temperature has been evaluated based on the determined kinetic model. The intensification of copper reduction in fire refining has been discusses on the basis of obtained kinetic data and analysis of various factors determining the time of reduction.

Jan 1, 2003

By H. Krogerus, P. Jokinen, T. Lintumaa

The energy consumption and recovery of chromium are important economic factors in ferrochrome production. Outokumpu has a lot of experience of the reduction behavior of the sintered pellets in industrial-scale furnaces and also on the grounds of numerous laboratory and pilot-scale investigations. Sintered pellets have shown a superiority over lumpy ore and briquettes made of the same chromite grade. The good performance of the pellets has also resulted in investigations on the reasons for such a performance. In this study, the factors affecting pellet behavior in smelting furnace were investigated. This study is divided into two sections, i.e. the investigations were on the factors affecting solid state reduction and on the factors affecting reduction under melting. These tests were performed by means of thermo gravimetry and by smelting tests. The correlation between the pellet characteristics and reduction behavior was shown and its influence on industrial-scale furnaces was discussed. Factors worth of consideration are for instance, the extent of oxidation during sintering, slag formation and chemistry in respect of molten state reduction, and the grain size of the chromite mineral in the raw material in respect of kinetic reasons (retention time in smelting).

Jan 1, 2007

By G. A. Beiswenger

The application of the law of supply and demand to the sale of crude oil is generally conceded, but the motives underlying the buyer&apos;s (refiner&apos;s) demands are not always obvious to the seller (producer). In some cases this obscurity has led to the conclusion that the refiner may be unnecessarily particular when he selects one crude and rejects another. This preference, however, is very largely the reflection of the refiner&apos;s product demands and the quality of the stocks obtainable from the selected crude. The purpose of this paper is to point out critical characteristics of the major classes of refined products and to show how crudes vary in their suitability for such products. With relatively few exceptions, available processing methods and addition agents make it theoretically possible to produce any type of refined product from any crude source, although it may not be economi-cally sound to do so. The widespread application of thermal cracking for converting higher boiling stocks into gasoline is well known. More recently cracking and refining in the presence of catalysts9 have been developed, as well as various processes for polymerizing lighter hydro-carbons into gasolines having desirable characteristics.6 For several years, selective solvents have been applied commercially to refining inferior quality kerosene, Diesel fuel and lubricating oil distillates .3 Improved methods for refining lubricating oils from crude residua,4 formerly suitable only for fuel, are now in use and a number of special solvent processes are available for dewaxing lubricating oils to low pour point.5 These improved refining methods have been developed not only to meet the demand for improved product quality but also to enable the refiner to obtain quality products from crude sources that would not yield such products by the older refining methods. In many cases, the utilization of these modern refining tools necessi-tates an appreciable expenditure for equipment as well as added manufac-turing costs, and their application therefore must be justified economically. Despite the availability of such tools, the added processing costs involved and yields obtainable may render their application entirely impractical. To illustrate this point, inspections of typical cuts from various crudes

Jan 1, 1940

By H. B. FERNALD

THE interesting and carefully developed formula which Professor Bucky presents for answering the question of whether proposed new equipment will give a net return on investment equal to or greater than that on present equipment starts with an assumption that the management may make this relative return a determining factor in its decision whether or not the new equipment should be provided. I do not question that in some cases the management may take this position, but I would point out the error involved in so doing. The proper test is not a comparison of the return on new as compared with the return on old investment, but is rather a comparison of the return on a particular new investment as compared with the return which would be obtainable from some other new investment which now might be made. Then I would point out that I believe Professor Bucky is in error in using as a factor in his computations the item of unamortized cost of old investment. The financial advantage to be derived from a new investment does not depend on the extent to which we may in the past have written off the cost of old equipment, nor does it even depend upon what was the original cost of that old equipment. Even the salvage or resale value of the old equipment will only enter into the picture to the extent that the present salvage or resale value differs from the ultimate salvage or resale value otherwise to be obtained, after due allowance for the interest factor.

Jan 1, 1930

By P. B. Bucky

IN this day of steady progress in the mining industry, especially along mechanical lines, the question of whether to discard present equipment for that of a new type often engages the minds of many officials of mining companies. The rapid strides made from year to year sometimes cause this question to be brought up within a year after new equipment has been purchased and installed. It is a moot question whether a machine that has been purchased last year should be replaced by a new one put on the market this year. As I see it, the reasons for the replacement of present equipment may be summed up as follows: (1) because of increased safety; (2) because of legal regulations; (3) because of increased profits. I think all of us, as engineers, will endeavor to put in as safe equipment as it is possible to devise. The tendency of mining companies in that direction is very gratifying.

Jan 1, 1930

By H. M. Dus, D. J. Smith

Resistivity tests indicated that, at temperatures lower than 1450°C, reducing agents alone, as well as burdens consisting of high-carbon ferrochromium and reducing agents, exhibit wide differences in resistivity. These differences are less pronounced at elevated temperatures. The resistivity of a reducing agent and the volume fraction it occupies are important factors controlling the resistivity of burdens of high-carbon ferrochromium. A mathematical model is formulated to describe the dependence of the resistivity of mixtures of conducting and insulating particles on the particle sizes and the volume fraction occupied by the conducting phase. The resistivity of burdens of high-carbon ferrochromium is high if the particle size of the reducing agent is larger than that of the other components of the burden. A number of reducing agents showed small variations in their reactivity towards chromite ore in the solid state. However, with chromite ore in the liquid state, reduction proceeded more rapidly with reducing agents occupying larger volume fractions. During the smelting of manganese ore, high initial rates of reduction were observed for reducing agents that had a high reactivity towards carbon dioxide and a high content of volatile matter, and that occupied a large volume fraction. High liq&apos;uid-state reactivities were observed for reducing agents occupying a large volume fraction and having a Iow degree of graphitization.

Jan 1, 1980

By Walter E. Kramer

The advantages derived from the use of pellet burdens in blast furnaces are so great, that hematite ores are being converted into pellets in greater quantities each year. The conversion of these ores into pellets appears on the surface to be relatively simple. In reality, this is not so. Serious difficulties are encountered in drying these pellets that do not exist in the drying of taconite concentrate pellets. The ores that present problems are goethite and earthy hematites. Green pellets prepared from these ores have very law shock temperatures, 200-600° F. The shock temperature of a green pellet according to our definition is the highest initial temperature to which a green pellet may be exposed without suffering decrepitation. Decrepitation may involve spalling, fracturing or total disintegration. The poor shock properties of these green pellets result from the inability of the vaporized water to escape freely and easily as it is formed with¬out affecting the integrity of the pellet. As a consequence, the pellets must be carefully dried prior to induration. This careful treatment is costly. The slow drying process restricts productivity and requires larger furnaces than desired. The use of an additive to elevate the shock temperature of the green pellets would increase productivity. Bentonite is used in some pellet plants to improve balling but it raises the shock temperature only slightly. Nalco became interested in the shock temperature problem because of its activity in the development of organic pelletizing aids for taconite concentrates. The findings reported here are an outgrowth of our experimental work on the development of shock temperature additives.

Jan 1, 1967

Existing fluid flow techniques may be readily applied to the design of ranges for seam gas drainage. The Reynolds number characterises the flow regime within the pipe and it can be used in conjunction with data on absolute pipe surface roughness to determine the system friction factor. The application of the solution to the isothermal compressible flow equation utili- sing Moody friction factors and the concept of equivalent length of pipe for fittings and valves provides a practical method for sizing gas ranges. The physical capacity of a range can be decreased by the existence of significant quantities of water in the range and also by the ingress of air into the system at poor pipe joints etc. Both problems can be elimin- ated by adequate attention to design detail.

Jan 1, 1982