Search Documents

The seam gas content at Westcliff Colliery is 12-15m3/tonne of coal.Composition ranges from 99% CH4 to 52% C02 in one area. Desorption rates are proportional to gas contents and CH4 is preferentially desorbed. A crushed zone of reduced permeability advances with the face - at Westcliff ribside crushed zones are 2.5 to 6.5m wide. Poor strata control widens crushed zones. 12 months of pre-drainage allowed 2 heading development and longer pillars to be used in a virgin area instead of 3 or more headings without drainage. Machined coal may lose as much as 1.6m3/tonne being conveyed out of Westcliff Colliery. Experience differs from mine to mine. Permeation is affected by time, strata movements, changing water content, and changing stress. Permeabilities vary from lOmd for Pittsburgh Seam to less than 1 and for the Bulli Seam. All these data and differences await further investigation.

Jan 1, 1982

By Jones TRP

The Agnew Nickel Mine has a short his-tory of mining activities. However it has experienced a large variety of ground support problems. These problems relate to geological, hydrological, geomechanical, structural and mining techniques. The majority of the prob-lems occur in other underground mines. How-ever the large serpentinite hosted ore body which contains over 80% of the ore has prob-lems rarely encountered in other mines. Sol-utions to the problems are only being gained by understanding the factors creating them.

Jan 1, 1985

By Dugan K. J

Mine operators are currently in a situation where market forces are acting to reduce profit margins and at the same time, regulatory bodies are insisting on improved mine safety and stability. This means that ground support must be made more cost efficient while maximising operator and equipment safety.A key aspect of ground support efficiency is the 'in the ground' performance. This paper discusses the factors that influence the way rock bolts and cable bolts perform. It highlights the need to know how support efficiency varies in different ground conditions.

Jan 1, 1992

By I Jabouri

There are many physical factors that can affect the self-heating rate of coal. The presence of seam gas has often been referred to as inhibiting coal self-heating due to the limited access of oxidation sites created by the presence of the gas adsorbed on the coal pores. Similarly, the presence of bed moisture in the coal also acts as an inhibitor of oxidation by blocking access of air into the pores. Gas drainage of a coal seam prior to mining removes both gas and moisture from the seam. Bulk coal self-heating tests in a two-metre column on both gassy, as-mined and gas-drained, dried high volatile bituminous coal show that removal of gas and moisture from the coal accelerates the rate of self-heating to thermal runaway from 8.5 days to 4.25 days, from a start temperature of 30¦C, with an airflow of 0.25 L/min. The corresponding gas evolution pattern for each of these situations is different. Therefore, it is necessary to take this change in coal condition into consideration when developing a spontaneous combustion management plan.

Jan 1, 2005

By NEWTON B. KNOX

THE war has forced the principal industrial nations of the' world into the strait jacket of a closely controlled economy; taxes have been heaped upon all enterprises in order to maintain the armed forces and to deprive the people of the ability to bid for goods now unavailable. These restrictions, controls, and taxes are unlikely to disappear entirely after the war has been won, for debts will remain to be paid with a long period of difficult readjustment. Although the new economy will doubtless offer plentiful opportunities for the advantageous use of capital, no investor can ignore the favorable conditions offered by industry in Latin America, where taxes are relatively low and the restrictions on free enterprise comparatively mild. In mining in South America, the great international corporations have

Jan 1, 1944

By George A. Miller

ALTHOUGH the Andean mountain belt, which contains almost all the metal deposits of the other South American nations, does not enter Brazil, this country is rich in mineral resources, for in area it accounts for half the continent and geologically it contains almost all of the Brazilian Shield. This great mass of ancient rocks has been relatively stable for a long time and forms a great area of plateaus and highlands interrupted only by the syncline which carries the Amazon River across it to the sea. Lowland Brazil - the great flood plains of the Amazon. Tocantins, Paraguay, and Parana Rivers-is of no interest to the miner, and in fact supports but a small proportion of the country's population. The highland area is divided into unequal parts by the Amazon River; the north half is underlain by the north lobe of the Brazilian Shield which extends into Venezuela as far as the Orinoco, and into the Guianas, and is known as the Guiana Highlands. Mineralization appears to have been weak in the Brazilian portion of these hills. In fact most of the ore deposits are to be found in the States of Minas Gerais and Bahia, although the neighboring states of Sao Paulo, Pernambuco, and Piauhy can also boast of some deposits. Goias and Matto Grosso are as yet incompletely prospected but are considered to contain reserves for the future.

Jan 1, 1945

By NEWTON B. KNOX

CHILEAN mining in the public mind is rightly associated with copper. Chuquicamata with its great hill of copper-bearing granodiorite as well as Sewell and Potrerillos with mineralized volcanic necks together can supply a good proportion of the world's normal necessities of that metal. Chile is an extremely long and narrow country, averaging only 109 miles wide. Its eastern frontier is the Andes and it is on the western slopes of these mountains that the great copper deposits have been discovered. West of the Andes a great longitudinal depres sion has permitted accumulation of nitrates and other soluble salts in the arid north; in the north center it is hidden by a series of cross ranges, but in the center a moderate rainfall makes it the country's most important agricultural region. In the south this depression is drowned and gives rise to a series of straits and fiords. This enormous cleft in the earth's crust is separated from the sea by a coast range of moderate elevation which in the south is represented by a series of islands and mushroom-shaped peninsulas

Jan 1, 1945

By NEWTON B. KNOX

PERU, lying south of Ecuador and having common frontiers with Brazil, Chile, and Bolivia, includes over a thousand miles of the Andean mountains. The coastal plain is arid and narrow and the Amazonian jungle region is of interest only on account of its oil and gold placer possibilities. The mountain zone, however, here forms one of the world's most highly mineralized regions. The Peruvian Andes, like their Bolivian and Ecuadorian counterparts, form two distinct chains separated by the great Apurimac and Maralion valleys; but these rivers cut through the Eastern range to join the Amazon drainage, and the central valley is missing north of the passes thus formed by these rivers; the localities where the ranges are joined are aptly called knots. In addition, in central Peru, there exists a third range lying to the east of the first two and separated from them by the Urubamba and Huallaga Rivers. The Eastern range, however, is of little importance to the miner for few metal deposits are to be found therein except for the gold mineralization in the South. In general, deposition of metals in the Peruvian Andes accompanied igneous intrusions which invaded the folded Paleozoic and Mesozoic rocks during the Tertiary; thus the ore bodies are all typical of shallow or moderate depths.

Jan 1, 1945

By NEWTON B. KNOX

IN Bolivia, mining is still the principal economic activity, as it was before and during the Spanish Colonial period. Tin, tungsten, antimony, copper, lead, zinc, gold, silver, sulphur, and a little bismuth are produced. The Andes mountains are divided into two main ranges in Bolivia; the Western range marks the border with Chile and the Eastern range forms the backbone of the country; in the North it drops rather abruptly eastward, to the plains of the Beni, whereas in the South it splits and is separated from the Chaco flatlands by a series of folded mountain ranges. In general the mineral deposits are found within the Eastern range or in the hills that rise from the high plateau between the ranges - really parts of the Eastern range partly submerged by recent sediments. The mineral belt is thus over 500 miles long and about 100 miles wide and includes most of the principal centers of population and the most important means of communication. The region is mountainous and the roads are bad; furthermore labor is a serious problem, for the land is poor and the agricultural population is never far from hunger. The floating supply of miners is limited and soon exhausted in any emergency like the present.

Jan 1, 1945

By NEWTON B. KNOX

THE Guianas region is a geological unit, consisting of the northern lobe of the Brazilian Shield, but political accident and the fact that rivers act as the principal means of transportation have divided the region between five separate sovereignties. Brazilian and Venezuelan Guiana have already been considered. The French, Dutch, and British colonies consist of a coastal plain some fifty miles wide, which, together with the lower reaches of the principal rivers, support the greater part of the population. Inland from this tidewater region is a wide area of low, forest-covered hills, under-lain by gneisses, schists, granites, and pegmatites of the Shield. As in Venezuelan Guiana, these rocks are overlain by a thick series of horizontal continental sediments intruded by moderately basic magmas. Gold, bauxite and diamonds have been the principal products of the colonies. The first metal is quite widespread in the hill country. The quartz mines are small, though occasionally rich; probably the greater number of veins remain undiscovered because of the thick mantle of decomposition product that covers the schists and gneisses. The greater proportion of the gold, therefore, is derived from placers which are exploited in all three colonies. Some geologists claim that they occur in two belts parallel to the coast; whether this feature has its origin in the location of the primary mineralization or in the gradients of the rivers is not clear. In some instances the river gravels grade into auriferous laterite. The laterites are well developed in the Guianas and represent the weathering products of the more basic rocks.

Jan 1, 1946

By Neil Rowlands

Particle liberation studies are commonly used in the determination of the proportion of locked and liberated phases in ground ores at various stages of mineral processing. These studies may range from a qualitative assessment of a polished specimen in an optical microscope to a full quantitative analysis of the liberation characteristics of fine grained complex sulfide ores using scanning electron microscopy and high level image analysis. However, the conversion of quantitative data to meaningful information on a mill operations level is by no means a simple task. This paper reviews the errors inherent in the SEM/Image Analysis technique and looks at the various methods available to minimize errors in data collection.

Jan 1, 1992

By L. Andrews

Nickel is recovered as a by-product of the platinum-producing process operated by Anglo Platinum. The metal is mined mainly as sulphide minerals contained in platinum ores. These pass through the concentrating, smelting and converting process route and nickel is finally recovered by electrowinning. Smelting of the concentrated ore in the electric furnace produces a melt with a high slag to matte ratio. The resulting furnace slag is granulated and later milled and floated to recover matte. A project was initiated to investigate the distribution of nickel in the slag in order to improve recovery. Slag samples were examined using a combination of chemical and mineralogical techniques. The granulated slag was found to consist mainly of a silicate glass phase, which reflects the composition of the molten slag in the furnace. Nickel occurs as free matte granules, as matte phases locked inside the glass, and in the glass phase itself. Whereas nickel in the matte is as sulphide, most of the nickel in the glass phase appears to be oxide- bound(i.e. in solid solution). Milled slag as flotation feed showed recovery-limiting features such as free matte with oxidized surfaces and unliberated matte inclusions in the slag. The biggest nickel losses, assuming no tapping problems, are in the glass phase solid solution. Only around 40% of nickel would be recovered from the slag, even under ideal conditions. Spoon and pot slag samples were also examined to see if casting and crushing would improve recovery. Although larger and therefore more easily recovered matte phases formed, nickel partitioned into crystalline silicate phases, limiting the maximum theoretical nickel recovery to 70%.

Jan 1, 2004

By Allen L. Hatch

Perhaps the greatest challenge to the non-ferrous extractive industry, aside from discovery and cost reduction, is the continuous effort toward the total recovery of metals. This is-and must continue to be-a joint endeavor on the part of the miner and the smelter, the first to trend constantly toward that form of concentration most amenable to the smelter and the latter to upgrade technical efficiency on the product delivered. What follows will be a smelter's-eye view of the relative value of gold, silver, copper, lead and zinc as they each are contained in copper, lead and zinc concentrates. The variety of combinations is obviously of such a magnitude that it will be necessary to restrict the observations to fundamental concepts.

Jan 1, 1966

By J. Paraszczak

Application of teleoperated and automated (or ?autonomous?) mobile equipment in underground metal mines represents a promising avenue for overcoming some of the challenges facing the industry. This paper addresses the overall effectiveness of autonomous loading and haulage equipment compared with conventional human-operated machines. Factors affecting availability, utilization, and production rate are explored, and an emphasis is placed on some problems and risks not present in conventional human-operated systems, as well as on the character and criticality of autonomous equipment. The need for a more in-depth analysis of factors affecting overall autonomous equipment effectiveness is stressed; these factors should be taken into consideration at the stage of feasibility studies. The paper concludes with recommendations and directions for future research.

Aug 1, 2010

By J. Paraszczak

ABSTRACT: Application of teleoperated and automated (or “autonomous”) mobile equipment in under-ground metal mines represents a promising avenue for overcoming some of the challenges facing the industry. This paper addresses the overall effectiveness of autonomous loading and haulage equipment compared with conventional human-operated machines. Factors affecting availability, utilization, and production rate are explored, and an emphasis is placed on some problems and risks not present in conventional human-operated systems, as well as on the character and criticality of autonomous equipment. The need for a more in-depth analysis of factors affecting overall autonomous equipment effectiveness is stressed; these factors should be taken into consideration at the stage of feasibility studies. The paper concludes with recommendations and directions for future research.

Jan 1, 2010

By Jacek Paraszczak

Application of teleoperated and automated mobile equipment in underground metal mines represents a promising avenue to overcome some of the challenges facing the industry. This paper addresses the issues of overall effectiveness of the autonomous loading and haulage equipment in comparison with conventional man-operated machines. It overviews and discusses the factors affecting availability, utilization and production rate. It puts an emphasis on some problems and risks not present in conventional man-operated systems, as well as their character and criticality. It stresses the need to analyze the factors affecting OEE of the autonomous equipment more in-depth than it has been done up to date and to take them into consideration at the stage of feasibility studies. The paper concludes with some recommendations and indicates the directions of the future research in this field.

Oct 1, 2009

By W. G. SWART

THE best estimate on reserves of iron ore in the Lake Superior district is that made, in 1920, by Mr. R. C. Allen, amounting to 2,947,225,000 tons of assured and probable ore. This includes direct- shipping or so-called merchantable ores, and those capable of beneficiation by demonstrated processes. De- ducting from this the 287,000,000 tons shipped since 1920, leaves a present reserve of approximately 2,500,- 000,000 tons, or; about 50 years' supply. The assured ore in this estimate is given as 1,560,500,000 tons, which checks Mr. Lake's estimate of 1,528,948,000 tons, or about 30 years' supply. This is not a long time in the life of the steel industry, and it can be readily appreciated that the matter is important enough to war- rant the attention it is beginning to receive. The first question that engages our attention is, What is merchantable ore? In 1902 the average of all Mesabi shipments was 56.07 per cent iron and 4.35 per cent silica. Twenty-five years later it had dropped to 51.99 per cent iron, with silica up to 7.92 per cent. It has remained around these figures for' ten or twelve years and, except for a probable rise in silica, can stay there for an indefinite period. Most of these figures I am giving cover the Mesabi Range. Including the other ranges does not change the figures greatly, and the Mesabi Range commands the situation, since it produces about 65 per cent of the total annual tonnage and, according to Mr. Allen, contains 81 per cent of the assured reserves, 50 per cent of the probable reserves, and 66 per cent of both the assured and the probable reserves.

Jan 1, 1926

By R. F. Holub, P. J. Dallimore

Basic to solving the problem of the role of radon transport on radon concentrations in mines is to establish whether it occurs primarily as diffusion and forced flow through porous rock or through fissures in the rock. The laboratory experiments performed involved measurements of diffusion and emanation coefficients, porosity and permeability of representative rock samples. Significant differences have been found when comparing the results of the laboratory permeability determinations to those of the mine determinations. Considerations of underlying principles, however, suggest that the diffusion and emanation coefficients are the same in laboratory and mine. It was also found that moisture content plays a dominant role in radon transport through rock. Using these concepts and findings, some conclusions about the radon concentrations in mines have been drawn.

Jan 1, 1981

By J. H. Frye, C. P. Sun

A PRIMARY substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver aneys.1-5 It has been shown that at least, four factors are involved: (I) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2.4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. CALCULATION OF RATES OF WORK- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By Robert D. Schmidt

The Bureau of Mines is conducting an investigation to develop remediation techniques for residential water wells whose yield has been affected in the long term, by underground mining. Initial work relating to this project was conducted in 1984-1987 at a room and pillar mine in Indiana County, Pennsylvania. Piezometer nest data from the room and pillar mine reveals that a downward gradient in piezometric head exists in shallow strata as a result of drainage into the underlying mine void. The vertical gradient in head in turn results in well bore leakage in open-hole water wells. The relative yield of valley wells is only slightly affected however because the high surficial recharge rate through fractures more than compensates for fracture leakage into the underlying mine. The relative affect of well bore leakage on well yield is greater in certain hillside and hilltop wells that have comparatively low inflow rates at shallow depths. The static water level of such wells is determined to a much greater extent by the chance interception of deep outflow fractures, than is the case for wells drilled in a more intensively fractured valley bottom. The lower static water level of wells that intercept deep fractures does not necessarily reflect the water table conditions outside of a small radius around the affected well. The results suggest that permanently isolating well bore outflow fractures may remediate certain open-hole residential wells that have been affected by high extraction underground mining.

Jan 1, 1986