Search Documents

By Donald R. Lamont

The paper outlines the reasons for and research behind the recent decision to adopt oxygen decompression in the UK. Currently used measures of decompression illness are critically appraised. The paper describes the main precautions to be taken on site to manage the fire risk from the use of oxygen underground. A summary of the initial results from the use of oxygen decompression in the UK is presented.

Jan 1, 2003

By C. S. Ha, H. S. Choi, D. Y. Shin

POSCO installed a new 100 ton oxygen bottom-blown converter in 2013 for the development of new steelmaking process named as PS-BOP which is reading POSCO-Saarstahl Basic Oxygen Process. This process was developed by the collaboration research between POSCO and Saarstahl AG in Germany that is based on substantial increase of CO post combustion in a converter by blowing hot air from the top of converter. The collaboration research has been finished successfully in November 2013 with 17% decrease in hot metal ratio (HMR) when hot air was blown from the top of the oxygen bottom-blown converter. After the collaboration research the converter has been tried to be operated as oxygen top and bottom-blown converter to reduce bottom wear and to decrease production cost with increased use of low cost Fe source by the help of increased CO post combustion. The presentation includes experience on the start up of oxygen bottom-blown converter, HMR reduction trials with hot air top blowing and transition from oxygen bottom-blown to top and bottom-blown converter operation.

Jan 1, 2015

By Jesse Puller, Ken Mills

"This paper describes the Australia, New Zealand Inflatable (ANZI) strain cell, its operation, and recent development for overcoring in exploration boreholes. The ANZI strain cell is an instrument system that uses the overcoring method of stress relief to determine the three-dimensional, in-situ stresses in rock. The instrument has been used successfully for over three decades in numerous underground mining and civil projects, but technical advances over the last decade or so have allowed the system to be deployed in surface exploration boreholes to greater depths than was previously possible. Recent development of a downhole electronic data logger, a wireline-enabled drilling system, and an instrument deployment system has simplified the process of obtaining three-dimensional overcore measurements at depths approaching 1km to a single shift operation.The capability to deploy ANZI strain cells in surface exploration boreholes represents a significant breakthrough for the design of underground mines and underground excavations generally. High-confidence characterisation of the in-situ stresses at the design stage provides the opportunity to design key infrastructure and mining systems to take advantage of the in-situ stress field from the outset before mining begins. Understanding the three-dimensional, in-situ stress field not only provides a measure of the magnitude and direction of loads acting within the rock mass, it also provides insight into the mechanics of all the various processes driving ground deformations, including which geological fault structures are at limiting equilibrium.INTRODUCTIONThe overcoring method of stress relief is one of the most direct methods for determining three-dimensional, in-situ stresses in rock. The Australia, New Zealand Inflatable (ANZI) strain cell combines overcoring with several other techniques to provide determinations of the three-dimensional, in-situ stress field and the properties of the rock and, importantly, provides an indication of how much confidence can be placed in the measurement. This paper describes the advances that have enabled overcoring of the ANZI strain cell in deep surface exploration boreholes and the development of various complementary techniques that build additional confidence in the determination of the in-situ stress."

Jan 1, 2018

By Raymond A. Bradbury

Martin County Coal Corporation operates three underground mines and two surface mines on Wolf Creek in Martin County near Inez, Ky. The original underground development was begun in March of 1970. The property being developed is leased from Pocahontas Land Corporation. The A. T. Massey Coal Company, whose offices are located in Richmond, Virginia, is the parent company and sales agent for Martin County Coal. Duke Power Company is the customer who will take all the production from the mines which ultimately are scheduled to produce 2,500,000 tons annually. The Norfolk and Western Railway Company built a 24-mile railroad into this huge reserve of low-sulfur steam coal. Four coal seams, all above drainage, are included in the lease. The Middle Coalburg and Stockton seams are being deep-mined now and it is in three mines that the diesel haulage equipment is used. Those of you who attended the AIME meeting in Birmingham last October or the Diesel Symposium in Pittsburgh in January of this year are familiar with the introduction of trackless diesel-powered haulage equipment into our Martin County mines. I made a presentation at each of those meetings which dealt with our first experience with Wagner Mining Equipment haulage units. These machines are sold exclusively by Lake Shore, Inc. whose offices are in Iron Mountain, Michigan.

Jan 1, 1973

By R. O. Harma

Introduction Wet autogenous grinding is utilized in three iron ore concentrating plants operated by the Cleveland-Cliffs Iron Company (CCI). This paper will trace some of the development in converting from the use of metal grinding mill liners to the use of rubber and will update the current performance of rubber liners in these applications. The Cleveland-Cliffs Iron Company is a natural resources firm with major interests in iron ore mining and processing and oil and gas contract drilling. The company also has interests in oil shale, uranium, forest products, and Great Lakes shipping. The three operations discussed in this paper are the Empire and Tilden Mines on the Marquette Iron Range in Michigan's Upper Peninsula and the Sherman Mine in northern Ontario, Canada. The Empire Iron Mining Partnership is managed by The Cleveland-Cliffs Iron Company and is owned by Inland Steel, McLouth Steel, The Cleveland-Cliffs Iron Company, and International Harvester. The Tilden Iron Mining Partnership is also managed by The Cleveland-Cliffs Iron Company and is owned by Algoma Steel Corporation, Ltd., Jones & Laughlin Steel Corporation, The Cleveland-Cliffs Iron Company, Steel Company of Canada, Wheeling-Pittsburgh, and Sharon Steel Corporation. The Sherman Mine is a joint venture managed by Cliffs of Canada, Ltd. and owned by Dominion Foundries and Steel Company, Ltd. and Tetapaga Mining Company, a wholly owned subsidiary of The Cleveland-Cliffs Iron Company. The concentrators at all three mines utilize two stage autogenous grinding. Empire and Sherman process magnetic iron ores (Table 1) and utilize magnetic, hydraulic, and flotation concentration methods. Tilden processes an oxidized iron ore (martite, goethite, and hematite) and utilizes a selective-flocculation desliming and flotation concentration flowsheet. Final grind particle sizes are 90% -325M (43k) at Sherman, 90% -500M (25,u ) at Empire and 85% -500M (25 µ) at Tilden. Developmental History The success of using rubber mill linings in Scandinavia led to the first rubber mill lining used by CCI. It was installed in a conventional primary ball mill at Republic Mine in 1964 as reported by Lindroos (1970). This was followed by additional rubber liners for both primary and regrind ball mills. Generally these rubber linings provided about twice the service life as compared to the Type I Ni-hard liners previously used. Grinding efficiency of rubber was found to

Jan 1, 1982

By R. O. Harma

Wet autogenous grinding is utilized in three iron ore concentrating plants operated by The Cleveland-Cliffs Iron Company (CCI). This paper will trace some of the development in converting from the use of metal grinding mill liners to the use of rubber and will update the current performance of rubber liners in these applications. The Cleveland-Cliffs Iron Company is a natural resources firm with major interests in iron ore mining and processing and oil and gas contract drilling. The company also has interests in oil shale, uranium, forest products, and Great Lakes shipping.

Jan 1, 1982

By R. Bruce Ferguson

"IntroductionThe Beaverlodge Operation of Eldorado Nuclear Limited is a uranium property located near the north shore of Lake Athabasca about 7 miles from Uranium City, Saskatchewan.The mill is a 2000 tpd carbonate leach operation producing a high grade yellowcake concentrate.The Lamella Thickener was purchased to replace a 55 foot conventional unit which had deteriorated beyond repair. The cost of the unit was considerably lower than for a conventional unit, installation was much simpler and the unit is much more compact allowing it to be installed in the mill basement and be insulated completely.The unit was sized according to the results of tests performed both by the supplier and Beaverlodge engineering staff. The supplier guaranteed overflow clarities of less than 100 ppm suspended solids. The Lamella thickener was developed by A. Johnson Co. of Stockholm, Sweden, is manufactured under license by Parkson Corporation of Ft. Lauderdale, Florida and is distributed in Canada by A. Johnson Co. of Montreal."

Jan 1, 1975

By D. K. Storer, W. Lee, S. Tkach

"A microcomputer-controlled multi-probe K-40 monitoring system was developed internally for the Phase II mill at the Lanigan potash mine. The K-40 probes were mounted in a variety of positions in several process streams, ranging from dry ore on a conveyor belt to brines and slurries. A description will be presented of the objectives, the equipment and the difficulties encountered in correlating results.IntroductionThe successful control and optimization of most metallurgical processes involves monitoring not only physical parameters such as flow rate and temperature, but also the chemical compositions of critical streams. Composition has proven difficult to measure on -line in industrial scale processes. However, in potash processing there is a convenient chemical parameter that has long been utilized to measure in situ the concentration of potassium chloride (KCl). Potassium has a long-lived isotope which is slightly radioactive. K40 decays by beta elimination to Ca40, ultimately radiating a characteristic gamma-ray photon. This gamma emission when detected by scintillation counter can be used to estimate the concentration of potassium in a process stream."

Jan 1, 1990

By J. E. Norton

PRODUCTION statistics show that during the period of emergence from the depres¬sion the coal industry was becoming increasingly cognizant of the economic and competitive necessity for mechanizing. About 1935 many of its leaders were becoming aware also of the alarming scarcity of men properly trained to cope with the new problems of mechanization. In order to get a factual statement of this problem, a special AIME Coal Division Committee + was requested to survey the condition. Its investigation disclosed that graduates of mining schools going into coal mining numbered 16 in 1939 and 15 in 1938. With this as a background, Pittsburgh Coal Co. foresaw that a comprehensive program was necessary if it was to enlist the services of trained technical men, who were an indispensable part of a mechaniza¬tion program. The purpose of this paper is to review the program set up, to comment on the successes and failures and to outline the future course of action. SUMMER WORK An inescapable conclusion from the mechanization statistics was that the opportunities in coal mining were good. Not only was there a void in technical skill to fill from past years, but the ac¬celerating rate of mechanization indicated an increasing demand for technically trained men for the future. The remedy lay primarily in presenting facts con¬cerning the coal industry to the under¬graduate engineers before they made their professional occupational choice. Based on this idea, one of the key points in the program - was summer vacation work for the undergraduate, which, through the inducement of summer earnings, brought men into the mines to take a look at the prospects. This was more successful than statistics indicate because the war badly scrambled the orderly working of the program, but it could not obscure the value of a summer work program. A decided advantage was that it gave the company a preview of the graduate. An observation on this part of the program is that it is extremely hard to gauge lower classmen, and we found it wise to give them the benefit of the doubt, as the last two years in college bring about surprisingly rapid develop¬ment in some men. We could readily single out the men at the opposite ends of the scale of competence. COMPREHENSIVE TRAINING PROGRAM Having adopted summer work as a

Jan 1, 1946

By William C. Laubengayer, Robert R. Godard, Harry Dobroski

A whole mine, computer-controlled communication and monitoring system for both normal and emergency use is installed and operating in the U.S. Steel Robena Mine complex near Uniontown, Pa. Portions of the system, including the coaxial cable and the key underground and surf ace phones, have been operating for over a year and a half. During this time the basic concept has been modified and new line amplifiers with directional switches have been developed to eliminate some problems in implementing the loopback feature. The quality of the audio and the availability of the system have been outstanding. Since early summer almost all subsystems have been completed. The experience with the telephone system itself, the pocket-pager call alert, section wireless radio, hoistphone, television, environmental monitoring, control and monitoring of equipment, voicedownlink/code uplink post disaster communications, post disaster through-the-earth monitoring, and the system center failure diagnostic routines are reviewed.

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By F. C. Muttitt

The physical arrangement of the continuous casting facilities at Algoma have been described a number of times in previous papers. For the purposes of this discussion, it is sufficient to state that the casting plant is located at a considerable distance from the basic oxygen shop which supplies it, involving a relatively lengthy ladle transfer movement. (Fig. I) The handling of the ladle by two separate cranes, first to the argon station, and thence to the casting machines, results in an average interval, from start tap to start cast, of 45 minutes. The effects of such extended retention time on temperature control and on refractory performance are well known. Tapping temperatures well above normal are necessary to insure that the ensuing heat losses do not result in an undue incidence of premature tundish freeze-offs. The heat lost, as well as being a function of the retention time, becomes more critical with smaller ladle size; winter temperatures add to the problem with their effect in chilling ladles and increasing radiant losses.

Jan 1, 1972

By Eric W. Johnson

In the late 1950's a low-grade copper ore zone was outlined at the fifty-year-old McIntyre Porcupine Mine in Northern Ontario. Following this an independent copper circuit was installed in the existing gold mill. The nature of the operation decreed that capital expenditure be a minimum. To this end, in order to resolve the problem of storing and grinding two separate ores, it was decided to install a divider in the existing 4000 ton capacity fine ore storage bin and to replace ten conventional feeders with sixteen Mexican feeders. The article describes a successful application of the Mexican type feeder.

Jan 1, 1968

By Thomas M. Larimer

Prior to April, 1961, the coal charge to Clairtonts coke oven batteries was 3" x 0" mine waslied coal having approximately 6.0% to 7.0% moisture. Even at this size and moisture content, the arching, rat-holing and hang-up was excessive and the effective live storage of coal was only 60% to 70% of the rated capacity of the coal bunkers, depending upon the moisture of the coal. In addition, many production delays were encountered in the time and methods required to fill the larry cars. The need for an improved metallurgical coke led to the introduction of pulverized coal to a portion of the plant in 196 1. When the full potential of the pulverizing equipment was realized, we were able to serve seven batteries in our second unit of batteries with pulverized coal through two coal bunkers. The discharge hoppers of these bunkers were equipped with air vibrators to assist the flow of pulverized coal into the larry cars. The vibrators were helpful in this respect but required considerable maintenance and caused damage to the bin plates.

Jan 1, 1968

By Crawford M

During the initial development of Mount Isa Mines power was supplied from a temporary power plant situated near the Man & Supply Shaft. The main power plant was placed in service early in 1931 and then comprised two Babcock and Willcox boilers, fired by pulverised fuel, and two British General Electric Company's turbo-alternators of 5,000 kW. each. Both plants have been described by A. F. McAskill in the Journal of the Institution of Engineers, Australia.From 1931 power demand progressively increased due to greater production, further mine development in the harder sulphides increased pumping for mine drainage and additions to mill and smelter until, by 1935, the plant was inadequate for further output commensurate with a reasonable safety margin.Coincident with the added power demand, operating conditions involved a fuel problem which could not have been anticipated. The ash content of the fuel supplied gradually increased from 13% to 16-5%, while the melting point of the ash decreased with higher pyrite content.Temperature conditions in the furnace required careful control to cope with ash formation and slag accretions.Consequently brickwork, excessively stressed on water walls, was constantly under repair, and required suspension periods of 50% of operating time for cleaning and overhaul.Load conditions varied continually, therefore the high heat liberations in the furnace, necessary to accommodate peaks in fluctuating output, resulted in ash fusion.

Jan 1, 1939

By W Ludlow, C Harrington

This paper presents an overview of the design and construction challenges to implement capping systems on Tailings Storage Facility’s (TSF) based on recent projects in Australia. Key aspects discussed include the cover design and barrier system to encapsulate the tailings, designing for a service life of 1,000 years, water management considerations. construction on tailings, vegetation selection and agronomy of the available capping soils plus the Health, Safety and Enivornmental challenges faced in working on tailings. Lessons learned from experience in capping TSFs are also presented. CITATION:Ludlow, W and Harrington, C, 2018. Experience with Capping of Tailings Storage Facilities for Decommissioning Projects in Australia, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 157–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Ole Bernt Lile

The well-known method of C. Schlumberger, Mise a la masse, has become a popular method again in ore exploration in Norway after many years of dominance by EM methods. The principle of the method is to place a current electrode within a conducting ore body and remove the other electrode to a great distance. (Figure 1). Often it is convenient to place a return electrode on each side of the area explored. The method is best suited for ores that have a conductivity contrast, relative to the host rock, of several orders of magnitude. The potential drop within the ore itself may then be neglected and the ore contact against the rock may be regarded as an equipotential surface. One may say that the ore body is electrically charged. Therefore, in Norway the method is now most often called the Charged Potential Method (abbreviated CP). The most usual way to present data obtained by CP, is to draw equipotential lines based on potential values measured in profiles on the surface. Such a potential map gives an immediate picture of the outcrop of the ore and also indicates disturbing conductors in the neighborhood. It may also be useful to look at the potential profile and its horizontal gradient along the strike axis of the potential map. These profiles may give information about the strike length of the conductor. Figure 2 shows the theoretical profiles of potential and gradient along the axis of the potential picture on the surface over a charged line plunging 15 degrees. It may be seen that the maximum of the gradient curve clearly indicates the lower end of the conductor. Figure 3 shows the corresponding pro- files over a charged line plunging 45 degrees. In this case, it is not possible to see an indication on the curve of the lower end. Only curve fitting could help interpretation in this case.

Jan 1, 1975

By Steven W. Hunt, Steven B. Fradkin, Roger J. Maurer

During the 1980s and 1990s, twenty deep shafts were constructed in Milwaukee to depths from 85 to 91 m (280 to 300 feet) through soil and weak rock thicknesses ranging from 37 to 69 m (122 to 227 ft). Adjacent compressible soils, settlement sensitive structures and high groundwater levels required that shafts be constructed without dewatering. Contractors attempted several methods of ground support and groundwater cutoff. Significant problems developed during construction of 11 of the 20shafts. One shaft collapsed; groundwater blow-ins occurred at five of the shafts; and seepage caused unfrozen windows at three of the freezewalls. Ultimately, combinations of grouting and ground freezing were utilized to complete all of the shafts into bedrock. This paper discusses the main design and construction challenges experienced and the lessons learned.

Jan 1, 2003

By F. G. Schora

The Institute of Gas Technology (IGT), under sponsorship of the U. S. Department of the Interior, Office of Coal Research (OCR), and the American Gas Association (A. G. A. ), has been undertaking the development of one of several processes to convert coal to high-Btu gas as a means of supplementing natural gas supplies. It is anticipated that there will be a significant need for such gas in the foreseeable future in order to meet the ever increasing demands for this preferred fuel form. HISTORY The development of the HYGAS® Process is based on various studies conducted at IGT starting back as far as 1945. Initial work was directed toward production of synthesis gas with subsequent catalytic methanation. By 1964 the concept of the direct hydrogenation of coal to produce methane noncatalytically was well-founded and the chemistry was reasonably well established. Work up until this point in time was financed by the American Gas Association. In 1964 the U. S. Department of the Interior, Office of Coal Research joined with A. G. A. to support the program. The objective at that time was to develop the necessary know-how to enable the design of a pilot plant, a necessary step in the ultimate commercialization of the process. Work for the next three years (1964-1967) emphasized investigation of fluidized-bed technology in the hydrogasification step, where moving-bed technology had been previously employed, as well as identification of commercially available catalysts acceptable for catalytic methanation of the CO and hydrogen in the hydrogasifier effluent under operating conditions in the system. By 1967, the preliminary design of a 3 ton/hr pilot plant had been finalized, and IGT received authorization from OCR to proceed with the detailed design and construction of that facility. The pilot plant was designed to study the following problems:

Jan 1, 1972

By Nag D. K

The Dolphin Scheelite orebody is located near the old mining town of Grassy on the south-east comer of King Island in Tasmania. Surface open cut mining of the Dolphin deposit was conducted for a number of years, then the proximity of the sea and adverse stipping ratio led to underground mining. As a result of the variable orientation and dimensions of parts of the orebody a number of mining methods were practiced at the Dolphin mine until 1990 when a combination of high processing and surface site costs coupled with low tungsten prices led to the cessation of operations. In this paper the different mining methods practised are examined and critically reviewed. The more successful mining methods were developed with experience and improving equipment technology to the extent that the underground operation produced ore at the lowest unit cost during the final years of operation.

Jan 1, 1995