Search Documents

By William Petruk

The concentrator of the Iron Ore Company of Canada consists of spiral circuits, a cone plant and a magnetics plant with regrind. The proportions of liberated and unliberated grains of iron oxides at each point throughout the concentrator were measured by image analysis, and recoveries were calculated for each particle type by the MATBAL materials balancing program. The results show that spirals and cones recover more than 92% of the liberated iron oxide grains in the size range of 848 to 150 um,, but the recovery drops off rapidly for finer grained particles. The tailings from the spirals and cones are reground and low intensity magnetic separators are used to recover liberated magnetite in the -37.5 um size range. The concentrator does not have a unit that efficiently recovers iron oxide grains in the size range of 150 to 37.5 um Consequently about 25% of the iron oxides in the ore are lost to tailings as liberated. grains in the size range of 150 to 37.5 um

Jan 1, 1989

By Kenneth V. Luza

Underclays are associated with coals found in eastern Oklahoma. These coals are of bituminous rank and are in beds of Middle and Late Pennsylvanian age. They occur in an area of about 8,000 mi2, within the southern part of the Western Interior Coal Region. The rocks of the area consist of a thick series of sandstones, shales, underclays, coals, and limestones. There are more than 40 beds of bituminous coal in the state, but only 12 of these have been mined over large areas. The 12 are, from oldest to youngest: the lower Hartshorne, upper Hartshorne, McAlester (Stigler), upper McAlester, Cavanal, Rowe, Secor, Weir-Pittsburg, Mineral, Croweburg, Iron Post, and Dawson coals. None of the underclay associated with these coal beds is known to have been exploited commercially. Nine samples of underclay from beneath the Croweburg coal were collected over a wide area in the eastern Oklahoma coal field for evaluation. The underclays are usually shades of gray with brown or orange iron-oxide staining. Although soft and plastic in some places, they are generally hard and slickensided, and contain abundant carbonized plant fragments. Bulk chemical analyses, clay mineral identification, and ceramic tests were performed on each underclay sample. The dominant clay minerals are illite and kaolinite with some mixed-layer clays. Silica (Si02) ranges from 45.96% to 59.03% and alumina (Al2O3) varies from 14.98% to 23.60%. The U.S. Bureau of Mines Tuscaloosa Re- search Center conducted the ceramic evaluations. Samples were slow fired from 1,000°C to 1,250°C in 50°C intervals. Bulk density, color, percent linear shrinkage, and percent absorption were determined for each slow fire test. All Croweburg underclay samples are best suited for building brick.

Jan 1, 1999

By A. Otsuki

This paper describes the evaluation method of dispersion and coagulation of silica nano-particles by means of interactive force apparatus. The apparatus measures the size of fine particles in aqueous solution or organic solvent of high concentration and/or low optical transparency. Other conventional apparatus for size measurements (such as, apparatus utilizing dynamic light scattering) are difficult to measure the size of particles in such conditions accurately, due to multi-scattering of light in the sample solution or solvent. The apparatus measures the interactive force between two surfaces, i.e. the gold-coated glass hemisphere and the brass flat plate, (which is fixed at the bottom of the sample cell). The apparatus has three parts, i.e. main part (which consists of electric balance, hemisphere and flat plate), control part (i.e. personal computer, piezo-stage controller and voltage supplier), and detecting part (i.e. multi-meter and oscilloscope). During the measurement, electric field is applied between the hemisphere and flat plate, and thus dielectric particles are arranged toward the direction of electric field in the area between two plates. When the two plates are close to each other, two different forces (i.e. repulsive force and attractive force) will alternately act on particles due to the structure change of the particles. The repulsive force occurs when the structure of particles is stretched by compressive force; whereas the attractive force occurs when the aggregate structure is broken. The cycle of the repulsive and attractive forces is a primary size of particle or size of aggregate, which depends on the degree of agglomeration. The measured size of particles, which is varied depending on their degree of dispersion and coagulation, determined the characteristics of the silica particles. In this research work, the effect of size and concentration of particles in aqueous solution on the degree of dispersion and coagulation of the silica particles were investigated. Spherical silica particles were selected for this investigation due to their variety of size. This apparatus can be used to evaluate the degree of dispersion and coagulation of other nano-particles in various solvents in many process industries.

Jan 1, 2014

By Julián Andrés Ortiz González

This work presents a series of experiments of Fatigue Crack Growth (FCG), which are intended to provide evidence about the main parameter controlling this phenomenon, whereas still no agreement about this, since the Paris´ theory is based on the principle that FCG is controlled by the ?K and the Elber´s theory says that the driving force is ?Keff. For the development of the experiments, some DC(T) specimens were machined with two different thicknesses: 2 and 30 mm to perform FCG tests in plane stress and plane strain state, respectively. Besides this, all FCG tests were carried out with a constant ?K e Kmax, measuring the strain with a Strain-Gage bonded on the back face of the specimen and seven Strain-Gages located on the crack growth path. The data needed to measure the crack opening load, and the ?Keff, were collected through a program developed in Labview. Finally, the data post-processing was carried out based on the ASTM standards and several articles of recognized authors in this field, in order to compare the two positions with the experimental data, and this way conclude which is the most consistent theory with the observed behavior.

Aug 16, 2017

By J. H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) amended the Federal Mine Safety and Health Act of 1977 to improve the safety of mines. The MINER Act established a Technical Study Panel (the Panel) to provide independent scientific and engineering review and recommendations with respect to the utilization of belt air and the composition and fire retardant materials in underground coal mining (1). Because frictional heating is a common cause of belt fires, the Panel recommended that the Mine Safety and Health Administration (MSHA) evaluate the drum friction test to determine if such a test would contribute to conveyor belt safety beyond that provided by the Belt Evaluation Laboratory Test (BELT). This paper compares the results of the drum friction test to results from the BELT and large-scale tests for six different conveyor belts. The results are used to evaluate the drum friction test as a method to determine the fire resistance of conveyor belts.

Jan 1, 2011

By Christiano Gianesi Bastos Andrade

Clays with high content of smectite are denominated bentonites, and are widely used in industry as, for example, agents for bleaching of vegetable oils, animals and minerals. For this use, the smectite clays are treated with inorganic acid of high concentration at temperatures under boiling point, which provide the bentonite´s bleaching power. In the present study, a sample of smectite from Cubati, Paraiba, Brazil, was submitted to treatment under moderate conditions (90°C, reaction times of 1, 6, 12, 18 and 24hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, acid solution/clay ratio of 1g/10mL), aiming to reduce impurities, responsible for the color of the clay, without causing significant changes in their structure. Thus, clay can be used in the cosmetics industry and other products with high added value. The treated clay was characterized by scanning electron microscopy (SEM), stereomicroscopy, energy dispersive X-ray detector (EDS) and X-ray diffraction (XRD). It was observed a bleaching in samples with time of 12h to 18h. With the DRX was possible to monitor the peak intensity of the clay structure and the sample with 12 hours of treatment was not significantly altered its crystalline structure, maintaining the peak clay at d001. The most pronounced changes in the bleaching occurred within the first 12 hours of acid treatment.

Aug 8, 2018

By S. Khoshjavan

In this investigation, the effects of different coal chemical properties were studied to estimate the coal Hardgrove Grindability Index (HGI) values index. An artificial neural network (ANN) method for 300 data-sets was used for evaluating the HGI values. Ten input parameters were used, and the outputs of the models were compared in order to select the best model for this study. A threelayer ANN was found to be optimum with architecture of five neurons in each of the first and second hidden layers, and one neuron in the output layer. The correlation coefficients (R2) for the training and test data were 0.962 and 0.82 respectively. Sensitivity analysis showed that volatile material, carbon, hydrogen, Btu, nitrogen, and fixed carbon (all on a dry basis) have the greatest effect on HGI, and moisture, oxygen (dry), ash (dry), and total sulphur (dry) the least effect. Keywords coal chemical properties, Hardgrove Grindability Index, artificial neural network, back-propagation neural network.

Jun 1, 2013

By K. Vaxevanidou

A combined chemical and biological treatment for the removal of heavy metals and arsenic from a contaminated soil was studied as a potential method for soil remediation. Small scale and column tests were conducted in order to ex-amine the effect of plant-compost and Na2CaEDTA addition on a calcareous soil highly contaminated with heavy metals and arsenic. EDTA is known to be an efficient leaching agent of heavy metals from contaminated soils but has no effect on arsenic. Compost tea on the other hand contains humics that can leach several iron compounds including Fe(III)-oxides and thus can extract arsenic bound to these oxides. The action of Fe(III)-respiring bacteria D.palmitatis was also evaluated for the reduction of iron oxides and compared to simple chemical treatment in the presence of compost in small scale tests. Results indicated that the addition of compost and EDTA into soil pulp lead to the predominance of reductive conditions and the simultaneous dissolution of both heavy metals and arsenic at high percentages. The presence of D.palmitatis did not further enhance the reductive dissolution of Fe(III)-oxides by compost and EDTA as it was observed in the inoculated samples. Column tests using soil as received revealed that, although the extraction of metals seems to be a slow process, compost is an effective oxygen barrier that promotes the reductive dissolution of iron oxides and the subsequent arsenic release together with the dissolution of heavy metals by EDTA.

Jan 1, 2005

By Dennis Dolinar

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

Jan 1, 2007

By C. Doucet

Since 2001, CANMET Mining and Mineral Sciences Laboratories (MMSL) have worked with Falconbridge Ltd. (now Xstrata Nickel) to evaluate trends in the strength development and water retention properties of a novel backfill material for underground mining, called gelfill. Between 2004 and 2006, extensive laboratory tests were undertaken under the leadership of the Deep Mining Research Consortium (DMRC). This paper compares results obtained from samples circulated through a mini-flow loop and a simple mixer. Although many parameters were studied over the last five (5) years, this paper focuses on the investigation of the effect of the mixing method, sequence and time, and the curing environment on strength development and water retention of gelfill. It was found that binder should be added as a powder to the mix in the mini-flow loop, and that mixing slurry in the mini-flow loop as opposed to the mixer generally yielded higher strengths. The practical implications of these observations are the subject of an on-going underground trial that will compare laboratory and in situ properties of regular slurry fill with gelfill.

May 1, 2007

By Ahmad Mahboubi

The damage caused by catastrophic earthquakes has always been an incentive towards more sophisticated building codes and requirements. In parallel to computer technology development, the engineers? attitude towards acquisition of more accurate results is increasing. This approach leads to designation of structural elements with more elaboration considering different aspects of their behavior. In addition, less simplified methods will be considered as satisfactory for analyzing such problems. The problem of soil-pile-structure interaction is one of the phenomena that can be included in this category. In general, there are two methods by which the study of soil-pile interaction phenomenon is studied. These include direct and sub-structuring methods. The sub-structuring approach relies on the linear or slightly non-linear behavior of soil since it employs the results of kinematic interaction analyses for inertial interaction studies. In the past, the kinematic interaction between pile-soil was considered as negligible. This was due to the softer nature of the surrounding soil that increased the time period of vibrations. However, more research revealed that although this approach was consistent in many cases, there were some sites where the time period decreased. This was due to the material properties of the foundation and the soil, in a way that caused the frequency of vibration meet natural frequency of the system. The second type of interaction is the inertial interaction which reflects the effect a structure on top exerts on the oscillation experienced by the foundation. This paper examines the impact of vertical load on the inertial interaction by virtue of impedance functions. Three different load cases for the structure at the top of a pile foundation were considered for the analyses conducted in this study. The changes in the stiffness and damping of the system by frequency are studied and finally, the results are presented.

Jan 1, 2010

By P. J. Kientzler, Y. C. Lo

The current study is concerned with the analysis and attempt at simulating the product size distributions obtained from a vibrating ultrasonic device. Systematic experiments of comminution were performed with natural sizes as well as monosizes in order to understand the breakage behavior of the device. A precise analysis of the device's breakage performance in the case of fine grinding of alumina samples will be presented. Initial steps to model the breakage events using a detailed mathematical algorithm will be discussed.

Jan 1, 1992

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By S Miller, R Smart, J Thomas

Single-addition and sequential net acid generation (NAG) experiments were carried out on natural and prepared samples with varying contents of organic matter and pyritic S. Results show that carbonaceous matter can produce significant quantities of organic acids during peroxide oxidation in the NAG test, which leads to overestimation of acid-forming capacity and misclassification of benign samples as potentially acid forming (PAF). Organic matter effects were most pronounced in samples with low S (less than 0.5 per cent) and total organic carbon (TOC) contents of greater than seven per cent. The single-addition NAG test will tend to overestimate acid potential in samples with little or no pyrite and high organic matter content, potentially leading to sample misclassification. High pyritic sulfur samples tend to show little difference in single-addition NAG acidities with increasing organic matter, and it appears that pyrite is preferentially oxidised by peroxide when present in significant concentrations (greater than one per cent pyritic S). In sequential NAG tests overestimation was greatest in samples with little or no pyrite, but highly carbonaceous (>20 per cent TOC) pyritic samples were affected in later stages as the pyrite was depleted. A modified NAG method is proposed to account for the relative proportions of pyrite derived acidity and organic acidity in a given NAG solution.

Jan 1, 2003

By Klaus Gamweger

There are different reasons for purging a metal bath. The operations are varied, for example the purging gas can be used as a reactive gas being part of the metallurgical process or as an inert gas using the rising gas bubbles for agitation only. The different purposes for agitation, chemical and thermal homogenization or a preferential movement of the slag to the slag skimming door have to be considered. It depends on the furnace type and its dimensions as well as the process characteristics what the focus is on. For an optimized arrangement of numbers and position of all single plugs in the furnace, mathematical modeling - the CFD Computational Fluid Dynamics method - is used. This paper shows how the operation of purging plugs can influence the metallurgical process of an anode furnace by the example of Jinchuan Copper in China. The potentials for savings in energy consumption as well as in time for oxidation and reduction are presented.

Jan 1, 2006

By Salah A. Taqieddin

In an open pit, or a quarry blasting operation, a muck pile of broken material of given size and quantities suitable to a load/hauling system is normally created at the foot of a bench. Fragmentation can be used to evaluate the efficiency of that blast configuration.

Jan 1, 1987

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009

By F. C. Harris, S. J. Gaab, J. Sattarvand, S. Duzgun

Underground mines are inherently dangerous due to potential hazards such as fires, explosions, and caving of rock. Although these events are rare, once they occur a speedy and safe egress of mineworkers is critical to survival. Static evacuation systems use exit signs or directional lines but can get obstructed or be hardly visible in smoky or dusty conditions. This paper presents the investigation of the effectiveness of a smart evacuation technology in underground mining, where a real-time guidance system leads individuals on an optimised path to the egress while avoiding danger zones, compared to conventional practices. Participants simulated an evacuation from a virtual reality mine, using the conventional system and the smart evacuation system with real-time guidance. The highest reduction in evacuation time using the smart method amounted to nearly 40% on average. Moreover, 83% of participants preferred the smart guidance system, and agreed that it could enhance safety.

Sep 1, 2021

By G P. S Resende, D E. G Oliveira, E A. S Baeta, T F. Bravin

There is currently in the mining industry, as well as in other industries, a movement seeking to increase investments in decarbonisation processes to help combat global warming. Among some initiatives taken is replacing diesel-powered mobile equipment in the mines with electricity-powered equipment, such as electric off-highway trucks or even belt conveyors in the mining operation. Samarco is a Brazilian mining company that since its conception has used a conveyor belt mining system in its mining operation, using only a small number of trucks to complement the mining process. This mining process that combines conveyor belts and trucks has brought environmental gains for the company since the environmental impact of conventional truck-only mining is greater than that of the combined system. To measure these gains, a medium-term mining plan was developed in which two fleet scenarios were detailed. One scenario contemplated a high level of detail of belt mining seeking its maximisation, while the other considered the operation performed 100 per cent by trucks, eliminating the use of conveyor belts. Through the comparison of these two scenarios, it was possible to make an inventory of atmospheric emissions and greenhouse gases for each one of them considering data such as types of equipment, diesel consumption, total distance travelled and energy consumption. The results showed that the fleet scenario with conveyor belts results in periods with up to 15 per cent less greenhouse gas emissions and 37 per cent less total particulates compared with the truck-only scenario. Therefore, the results confirm the environmental benefits of the method and the need to look for ways to even expand it in future operations through a study to identify the potential areas in the long-term mining plan.

Sep 18, 2023

By C. Zografidis

Environmental protection, economic prosperity and respect of the need for social equity promotion, constitute a prerequisite for any modern industry aiming to operate in a sustainable manner. The Natural Stone industry in Europe, a sector comprising mainly of SMEs, despite the fact that consists a dynamic extraction sector, often lucks the resources to apply novel techniques and management schemes towards achieving sustainable performance. I-STONE, an EU Integrated Project funded by the 6th Framework Programme, is aiming to contribute in the improved performance of the Natural Stone industry. A primary project objective is the re-engineering of the stone production chain, in order among others to considerably in-crease its efficiency and productivity, and minimise the amount of stone wastes disposed. The present paper, resulting from the research con-ducted on environmental management within I-STONE, is focusing on the use of sustainable indicators as a tool for the assessment of the stone industry?s performance. Based on Commission Decisions and reported studies, a list of indicators was selected and used within I-STONE, including environmental and socio-economic indicators. A set of selected environmental indicators were quantified based on operational data of a number of Greek and Portuguese quarries examined as case studies. The analysis indicated that an integrated strategy, including the application of novel operation techniques and equipment, waste minimization and systematic environmental monitoring and reporting, constitute key factors for the sustainable operation of natural stone industry.

Jan 1, 2007