Search Documents

By A. L. Mackie

Mine water from base metal mines is generally characterized as having high concentrations of heavy metals and low pH, resulting in the need for treatment prior to discharge to receiving waters. In this study, two high-rate clarification processes were evaluated at bench-scale: the high density sludge (HDS) process and sand-ballasted flocculation. High-rate clarification processes generate larger, denser flocs which settle more quickly than those formed in conventional flocculation processes. The HDS process uses recirculated sludge in order to seed floc formation, whereas ballasted flocculation uses microsand. Both of these high-rate processes require the addition of quicklime or hydrated lime to increase pH and allow for the formation of insoluble metal hydroxides, which can then be removed in the clarification stage. Previous research has shown that cement kiln dust (CKD) can effectively replace quicklime in conventional sedimentation processes for metals and acidity reduction to meet discharge guidelines (Mackie & Walsh 2012). CKD is an alkaline by-product of cement manufacture that has fine particle sizes and varying free lime concentrations depending on the manufacturing process. The lower solubility (i.e., free lime content) of CKD requires larger doses of material to be added to reach treatment pH targets for metals precipitation. The purpose of this study was to evaluate the treatment efficacy of high-rate clarification processes for mine water treatment, compared with conventional sedimentation, at bench-scale with conventional (i.e., lime) and novel (i.e., CKD) pH adjustment additives. Results of the study showed that all treatment processes (i.e., HDS, ballasted flocculation, and conventional sedimentation) were able to reduce target metal concentrations to well below Canadian guidelines (i.e., total zinc and total nickel < 0.5 mg/L, total copper < 0.3 mg/L) using either CKD or lime. Additionally, mine water samples treated with CKD generated lower sludge volumes than those treated with lime (i.e., 50 versus 100 mL for conventional sedimentation and 100 versus 200 mL for HDS) even with increased concentrations of solids introduced during treatment. This is most likely due to slower neutralization rates when using CKD, due to its lower solubility, as well as finer particle size. The sand-ballasted flocculation process was able to reduce final turbidity in CKD-treated samples while the HDS process did not when compared to conventional sedimentation, making the ballasted flocculation process preferable for reducing final solids concentrations in CKD-treated mine water.

Aug 1, 2013

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on total nitrogen oxides (NOX) concentrations were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes.

Jan 1, 2011

By L. D. Patts, S. J. Janisko, E. G. Cauda, A. D. Bugarski, G. H. Schnakenberg, J. A. Hummer

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on the performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for DFEs when the engine was operated at high-load modes rather than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on the total concentration of nitrogen oxides (NOX) were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes..

Jan 1, 2011

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy&apos;s resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

By J. E. Sallee

An experimental study has been conducted on the level of arsenic contamination in samples of zinc oxide when the zinc oxide is contacted with gas mixtures containing As4O6(g). This contamination has been determined as a function of A4O6 saturation pressure, temperature, zinc oxide sample surface area, impurities, and oxygen level in the gas mixture. The results indicated a rather clean separation can be achieved between condensed zinc oxide and gaseous arsenic oxide as long as attention is given to temperature control, and the final zinc oxide surface area. For a 300°C operation temperature and an AqOg saturation pressure of 0.38 TORR (or 0.05% As406 by volume), the contamination level is expected to be approximately 100 ppm. This suggests that arsenical dusts can be treated in the HRD flame reactor process and a reasonable purity zinc oxideproduct produced. The results also show no evidence of zinc arsenite or zinc arsenate formation.

Jan 1, 1994

By J. G. Groppo, D. J. Sung, B. K. Parekh

Hyperbaric filtration for the dewatering of fine coal cleaned by froth flotation was evaluated on a laboratory scale. A laboratory pressure filtration procedure designed to obtain a uniform cake structure from dilute slurries containing a significant amount of coarse material is described. Baseline tests were conducted to determine the optimum operating conditions for the eventual application of the process to a continuous pilot-scale hyperbaric filter. Investigated were filter operating parameters such as driving force, time, cake thickness, percent solids, viscosity and pH.

Jan 1, 1996

By J. G. Groppo

Hyperbaric filtration was evaluated at the laboratory scale for dewatering fine coal cleaned by froth flotation. A laboratory pressure filtration procedure is described to obtain uniform cake structure from dilute slurries containing a significant amount of coarse material. Baseline tests were conducted varying filter operating parameters such as driving force, time, cake thickness, percent solids, viscosity and pH to determine optimum operating conditions for eventual application on a continuous pilot scale hyperbaric filter.

Jan 1, 1994

By J. A. Herbst

Introduction The ability to evaluate the improvement resulting from the implementation of an automatic control system is essential to the Justification of its cost. This evaluation may occur after anew control system has been commissioned. In other cases an existing plant which is operated manually may be automated only In part in order to determine In ether the met of it should be. Finally. in some instances dynamic isolation my be used prior to installation of the control system to determine the strategy to be used or to evaluate the improvements In process performance expected from automatic control. This paper describes the development of a methodology for making these evaluations. In order to obtain an accurate assessment of Improvements In a short time, statistical methods can be employed. Mineral processing plant, are subjected to many types of both random and deterministic disturbances of various duration. The statistical method, available for process control at analysis are designed to counter the obscuring effects that random disturbances have on such as evaluation. The basis for evaluation and comparison is some freely chosen measures of process performance termed the performance index or objective function. The experimental data used to calculate the performance index should, if possible, be collected by alternately running a circuit Or plant with the two or more type, or control being tested ("serial testing”) or more preferably, by running two circuits with the two type, of control side by side ("parallel testing") . The performance index is a random variable so that when comparing two types of control, statistical hypothesis testing must be used. By testing s hypothesis statistically one accept, or reject, a (null) hypothesis [ ] concerning the mean or variance of one or more performance indices. For example, a hypothesis Ho might be that the mean of a performance index with stabilizing control is larger than with manual control. Defining a Performance Index The performance index, denoted by [ ] , is a measure by which alternative strategies or situations my be cam peered on either s technical or an economic basis (see Table 1). Technical measures are concerned with the effects of control on process variables or outputs or on the deviations of controlled variable, from their setpoints. For commotion circuit, important technical measures of performance are throughput, product fineness and the consumption of liners, media and electrical energy. For flotation circuits important technical .satires are recovery, grade and reagent consumption. Economic measure such a, cost and profit n usually determined from a combination of technical measures and are usually the final factor upon which a decision may be made, although a control system my achieve higher values of technical measure , the control effort expended my be of such magnitude that the economic measures, such as cost, are poor. Running Comparisons Comparison, between automatic and manual control are normally done with data obtained before and after control system Installation, unless ore characteristics remain the same during the period of data collection the results will be biased. By running the test circuit with the control system alternately turned on and curled off until all possible ore type, have been run through the circuit, unbiased result, can be obtained. This mode of testing is termed “serial testing.” An alternative and potentially more powerful and quicker made of testing is "parallel testing" in which two circuits, one with the type of control being tested and one without, arm run aide by side. In this type of testing both circuits process the same ore so that valid results occur sooner than with aerial testing. The data may be averaged before testing or the differences in the performance indices may first be calculated before averaging. However, the two circuits must be nearly identical in their mechanical characteristics otherwise differences other than the degree of control will bias the results. It mechanical differences exist than it my be necessary to adjust one or the circuits prior to testing. Sometimes it is possible to correct far mechanical differences based on Inherent efficiency calculations made with a model. Hypothesis Testing Once the data is collected, hypothesis fencing can be carried out to determine if the automatic control system has resulted in a statistically significant improvement. One can construct a histogram of the distribution or performance indices with am without control such as Figure 1, or the

Jan 1, 1991

By J. Githiria, D. Wachira

The conventional truck and shovel haulage system has become expensive to operate in most mines due to current strict environmental conditions, increase in depth and size of open-pit mines, increase in labour costs, and fuel costs. These factors have motivated the search for alternative material haulage options in open-pit mines. In-pit crushing and conveying (IPCC) system has been regarded as a plausible alternative in material haulage systems. However, usage of IPCC has been limited to a few mines due to limited knowledge of IPCC performance, and other technical factors of the system. This paper investigates, and evaluates the productivity performance of four types of IPCC systems (fixed, semi-fixed, semi-mobile, and fully mobile IPCCs) using mine productivity index (MPi). Using a model developed by MATLAB, the MPi for the four systems is computed using input variables such as availability, utilisation, performance and number of trucks and shovels in a limestone quarry. The mine productivity index for fixed, semi-fixed, semi-mobile, and fully mobile IPCC is obtained as 67.13%, 69.02%, 70.52%, and 71.52% respectively. In conclusion, the fully mobile in-pit crushing and conveying system is the most appropriate IPCC in the quarry, due to its better productivity performance compared to the other three IPCC systems and the truck and shovel system currently in use.

Sep 1, 2021

By Donald W. Gentry

The evaluation of industrial minerals deposits for investment decision making follows the same basic principles that apply to metallic deposits. For example, the quantity and quality of the mineral occurrence is assessed, engineering/economic feasibility studies are performed for various production scenarios, project evaluation criteria are calculated for each alternative, and finally, an investment decision is made. A more specific evaluation-related example of commonality between metallic and nonmetallic deposit assessment relates to the various parameters which impact project feasibility studies. There exists a suite of pertinent factors which must be considered, studied, and analyzed when evaluating any mining property. Table 1 is an outline of some, but certainly not all, of the various factors which should be considered when preparing feasibility studies on mining properties. Most analysts agree that all the factors listed in Table 1 should be assessed to some degree in at least one of the feasibility studies prepared during the property&apos;s evaluation period.

Jan 1, 1984

By Alireza Golabchi

The AEC (Architecture, Engineering, Construction) industry is an information intensive industry and all related processes employed during different phases of a project, including planning, designing, building, manufacturing, occupying, and maintenance, involve vast amounts of data that is used for a wide variety of purposes. Building Information Modeling (BIM) is a powerful shared knowledge resource which stores this data to support decision making about a facility through all these different phases in its life cycle. Nowadays, BIM is mostly used in the design and construction phases while it can also be highly beneficial beyond those stages. For example, in the Operation and Maintenance (O&M) phase, BIM could be used for automated facilities management or robotic inspection to provide semantic knowledge for navigation. For any implementation not related to the original intent of the BIM (design), organizations need to be able to represent their project data in a common interpretable form, which provides the possibility of an accurate exchange of data among different software products and platforms, known as interoperability. This study has investigated the current state of interoperability between software products used as Building Information Modeling tools. The main focus has been on a popularly used format for BIM models, Industry Foundation Classes (IFC), since it has been specifically developed to enable standardized data exchange. The research methodology involved a comprehensive literature review and the gathering of all fragmented prior research related to the field in order to develop a consistent understanding of the current state of knowledge. This was accompanied with a detailed case study that evaluated and compared two dominant pieces of BIM software, Revit and Bentley, and examined their interoperability strengths and weaknesses while using the IFC format.

Aug 1, 2013

By Richard Druesedow, Richard Ray

Tests at the VP-5 "C" shaft fan installation of Island Creek Coal&apos;s Virginia Pocahontas Mines were performed to determine pressure drop due to the design of the shaft collar and ductwork leading to the fan. Data from the test locations in the shaft, duct and fan indicate significant pressure losses in the system as well as significant turbulence in the flow. Data taken with a 3-D probe in the fan annulus confirmed the importance of using this type of instrument in turbulent flow applications. This data will be later supplemented with data taken after addition of turning vanes in the 45° turn adjacent to the fan inlet.

Jan 1, 1993

By R. Pakalnis, C. A. Dreesbach, L. A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control systems to monitor rock mass loads at Tg Soda Ash’s trona mine, Granger, WY. Axial and shear loads were determined to levels of strain gauge accuracy of ±5 N or ±5 microstrain. These gauges were embedded in a remanufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. These data provide necessary input for an operator to design a safer working environment for miners.

By Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control systems to monitor rock mass loads at Tg Soda Ash&apos;s trona mine, Granger, WY. Axial and shear loads were determined to levels of strain gauge accuracy of ±5 N or ±5 microstrain. These gauges were embedded in a remanufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. These data provide necessary input for an operator to design a safer working environment for miners.

Jan 1, 2001

By Alan E. Bland, Jerry G. Rose, Thomas L. Robl

This paper describes the observed variability of the chemical composition of coal preparation plant refuse for the major producing seams of Kentucky. Both the Appalachian Coal Field of eastern Kentucky and the Eastern Interior Coal Field of western Kentucky are represented. Also reported is the variability observed in the chemistry of the coal refuse due to cleaning, and the observed chemical variations between past and present production samples. This represents part of a larger study directed toward characterization and utilization of Kentucky coal refuse.

Jan 1, 1978

By G. B. Harris, C. W. White

A study to investigate the recovery of base metals, notably copper, nickel, cobalt, zinc and manganese from iron-free concentrated chloride solutions using ion exchange was undertaken. In such solutions, apart from nickel and, to a lesser extent manganese, these metals are present predominantly as complex anions, and therefore conventional separation techniques based on cationic resins are not applicable. The results demonstrated that zinc, copper and cobalt can all be separately recovered leaving nickel and manganese behind. Specifically, zinc is a major nuisance element in nickel and cobalt processing, and the testwork showed that it can be preferentially removed prior to copper and cobalt. Selective resins for both copper and cobalt were identified, and it was demonstrated that the strength of the chloride background matrix has a significant effect on the efficiency of separation. An additional major advantage in such systems is that stripping can mostly be effected with water. Finally, some observations are made on the hurdles that must be overcome when attempting to introduce and commercialise new technologies.

Jan 1, 2015

By Patricio A. Riveros

Various types of commercial ion exchange resins were evaluated with respect to their ability to extract gold from cyanide leach solutions. Large differences were found among the various resins in terms of selectivity and gold loading. The hydrophi­licity and the charge density appear to be the main factors that determine the resin characteristics. Polystyrene weak-base resins, such as Dowex MWA-1, exhibited the best all-round performance.

Jan 1, 1990

By S. Masambi, S. M. Bradshaw, C. Dorfling

The presence of iron in base metal leach solutions complicates nickel and copper recovery processes. Leach solutions are commonly purified by precipitating iron as hematite, jarosite or goethite. Fast oxidation of ferrous to ferric is an important step to remove iron by precipitation at low pH values. This study reviews the ferrous oxidation mechanism and reaction rates in chloride media using molecular oxygen. This work contributes to the development of a better understanding of iron precipitation processing steps, which continues to be an important matter in hydrometallurgy. The specific objectives were to investigate (1) the effect of key process variables (acid concentration, copper concentration, and temperature) on the rate and extent of ferrous oxidation by dissolved oxygen and (2) the oxidation mechanism by varying chloride and hydrogen ion concentrations separately. Batch oxidation tests were performed using synthetic chloride solutions containing 45 g/L Fe and 3 g/L Ni at 50 and 80°C, dissolved Cu concentrations (0.3 to 3 g/L) and HCl concentrations (2 to 4.6 M). Regression analysis indicated that the significance of the effect of different variables on the extent of oxidation achieved after five hours decreased in the following order: HCl concentration > Cu concentration > temperature. Increasing the HCl concentration from 4 M to 4.6 M caused the degree of oxidation achieved after two hours to increase from 58.3% to 98.1%. The catalytic effect of dissolved copper on ferrous oxidation was more significant at low acid concentrations. Experimental data suggest that rapid oxidation of ferrous is possible at high HCl concentrations for two main reasons. First, the formation of ferrous chloride complexes allows ferrous oxidation to proceed without the formation of superoxide as an intermediate product (the rate limiting step in dilute acid solutions). Second, the formation of ferric chloride complexes stabilises the oxidation product.

Jan 1, 2016

By N Nosaka

Sinter plants currently have to use many types of ores with different properties due to the great demand for iron ores, which was driven by the massive growth in Chinese iron and steel industry. On the other hand, the development of iron ore mines is limited and the quality of iron ores is in a tendency of deterioration. Therefore, the quick evaluation of iron ores has become more important for a stable sintering operation. In addition to such a background, the CO2 gas emission should be decreased from sinter plants according to the Kyoto Protocol on reduction in greenhouse gases. The present paper first describes the methods for testing the metallurgical properties of iron ores, which use a small volume of sample mainly focusing on magnetite ore that is effective for reducing CO2 and NOx emissions from sinter plants. The sintering properties of ores are evaluated separately according to each stage in sintering process, that is: heating stage before melt formation, primary melt formation in adhering fines layer of pseudo-particles, and assimilation of nucleus ore particle with calcium-ferrite system melts.Next, the application of the tests to the blending ores is introduced showing examples of the studies on the effective usage of the magnetite ores with Marra Mamba type ores.

Jan 1, 2005

There are circumstances where the ordinary techniques of experimental variography in geostatistics û now in common use despite their recent origin û are not quite successful. This paper describes a new addition to the geostatisticians tool kit developed by one of the renowned leaders in the field to cope specifically with these circumstances. Possible application of this technique will be outlined when it will be seen that there are still problems remaining to be solved in its use for economic evaluation of deposits with irregular mineralisation.

Jan 1, 1984