Search Documents

By S. Tan

In this paper, several commonly used computer truck dispatching criteria are evaluated. A computer-oriented truck dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics, and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. All basic dispatching criteria including minimizing truck waiting time, minimizing shovel waiting time, minimizing truck saturation, maximizing truck momentary productivity, or truck routes optimization provide a local optimal solution. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely. Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. However, based on the simulation results of the mine operation, several dispatching criteria which have good potential to increase performance can be selected. It may be necessary to search for the best combination of these truck dispatching criteria for a given situation. For example, a truck flow measurement such as the truck clustering factor at shovels can be used as a switch parameter to change from one criterion to another. The values for the switch parameter at which actions should be taken to change the criterion can be established through simulation programs.

Jan 1, 1992

By R. V. Ramani, S. Tan

In this paper, several commonly used computer truck-dispatching criteria are evaluated. A computer-oriented truck-dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. However, several dispatching criteria that have good potential to increase performance can be identified. All basic dispatching criteria, including minimizing truck waiting time, waiting shovel with minimum waiting time, minimizing truck saturation, maximizing truck momentary productivity or optimization of truck routes, provide local optimal solutions. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. It may be necessary to search for a hybrid combination of the several truck dispatching criteria that have good potential for a given situation. An approach to selecting such a hybrid dispatching criterion is presented.

Jan 1, 1993

By L. Yan, T. Lutz, J. Noll

"Mine disasters, such as fires and explosions, can create a hazardous atmosphere due to the generation of carbon monoxide (CO). After a mine disaster, contaminated mine air can enter the refuge alternative (RA) as miners enter. Most built-in-place (BIP) RAs use an air delivery system to provide an unlimited supply of breathable air through a borehole which also serves to purge contaminants. In order to determine what levels of contaminants enter the RA, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted testing in NIOSH’s Pittsburgh Experimental Mine using groups of 5, 15, and 30 subjects entering the RA. The experiment used sulfur hexafluoride (SF6) as a tracer gas that was released into the air outside of the BIP RA to establish a uniform concentration. After the human subjects entered the BIP RA, the SF6 levels inside the RA were measured to quantify how much of the tracer gas entered the BIP RA. In tests conducted while the borehole air supply was left off as test subjects entered, interior contaminant levels were less than 3% of the exterior concentration. In tests conducted with the borehole air supply activated as test subjects entered, the interior contaminant levels were measured at less than 2% of the exterior concentration. Considering a mine disaster can result in 10,000 ppm of CO in the mine atmosphere, these percentages indicate that unhealthy CO concentrations that may lead to headaches, dizziness, and loss of judgement can occur in a BIP RA. This information will help mines make decisions concerning air locks, air delivery systems and a determination if purging mechanisms are necessary. INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and enforcement of mine safety standards (MSHA, 2006). Section 13 of the MINER Act specifically directs the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of RAs for underground coal mines. This mandate culminated in the 2009 adoption of changes to the 30 CFR mining health and safety regulations, requiring underground coal mines to provide RAs capable of maintaining a life-sustaining environment for persons trapped underground. Such RAs can be either pre-fabricated or BIP shelters. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe, breathable atmosphere within RAs."

Jan 1, 2018

By J. M. Keane, C. K. Chase

Critical to successful dump and heap leaching of copper is an adequate evaluation of applicable parameters. This paper deals with methods to establish optimum conditions for dump and heap leaching copper so that commercial operations can proceed. Discussion is also offered of ore occurrences and preparations for dump or heap leaching.

Jan 1, 1988

By H. Sakurai, M. Kato, F. Tanaka

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. The conditions in the CL- furnace change its settling efficiency, resulting in high variability of copper losses in slag. Modifications of the operation and maintenance procedures for the CL-furnace have significantly and sustainably reduced the copper losses in Gresik smelter to below 0.7%. A series of flow patterns evaluation in the CL-furnace demonstrated how the chemical reactions and settling conditions of the CL-furnace has been improved by the new operating procedures. Settling mechanisms for the matte droplets in the CL-furnace is also discussed using image analysis of solidified slag. INTRODUCTION The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace (CL- furnace) for settling the slag/matte mixture formed in the smelting furnace. Since the top-blowing in the S- furnace agitates the molten bath strongly, matte droplets are dispersed over the slag phase when melts flow out of the S-furnace. Thus, the CL-furnace has an important role to settle and recover matte droplets efficiently. Since many papers have ascribed major part of copper losses to matte droplets suspended in slag (Tanaka 2007; Genevski et al., 2008; Starodub et al., 2016), flow patterns of slag in the CL-furnace can affect greatly on the profitability of smelters which have adopted the Mitsubishi process. PROCESS DESCRIPTION Figure 1 illustrates the Mitsubishi process schematically. The Mitsubishi process is the only system for continuous production of blister copper from copper concentrates and consists of 3 furnaces connected by enclosed launders those ensure the minimum emission of fugitives. In a smelting furnace (S-furnace) copper concentrates are fed with flux, oxygen-enriched air to form a mixture of slag and matte which cascades down to a slag-cleaning furnace (CL-furnace). The CL-furnace settle matte droplets in the mixture on the crucible from which matte is siphoned to a converting furnace (C-furnace), while discharging the cleaned slag (CL-slag). The C-furnace converts matte to blister copper by the top-blowing of oxygen- enriched air.

Jan 1, 2019

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By J. J. Taute, N. B. du Preez

"A well-performing solvent-extraction circuit is a key part of producing good quality copper cathode. To ensure consistent operation, a good understanding of the circuit’s operation and an ability to rapidly troubleshoot key parameters is required. This paper briefly discusses the modeling of solventextraction circuits. The paper then goes on to discuss the determination of key performance parameters from plant data and comparing these with the circuit models to quantify circuit performance. The identification and troubleshooting of circuit issues is presented with a worked example. INTRODUCTIONA well-performing solvent-extraction (SX) circuit is a key part of producing good quality copper cathode. To ensure a consistent, high-quality operation, a good understanding of the circuit performance is required. Evaluating the performance of an SX circuit is an extensive topic. The objective of this paper is to focus on the evaluation that the metallurgist should be performing on a regular basis using flow and concentration data. This paper does not cover important topics, such as crud management, phase continuity, or organic management. Some basic SX modeling concepts are first be presented. The calculation of the parameters is then presented with a brief discussion and recommended ranges (where applicable). A worked example is used to provide a basis for further discussion on the evaluation of the calculated parameters and use of data collected.BASIC SOLVENT-EXTRACTION MODELING CONCEPTSThis section presents the basic modeling concepts used in SX simulation packages currently available. SX reagent suppliers have invested significant time and effort into collecting data on the performance of their reagents under different conditions. Based on these data, suppliers have developed packages which they normally make available to their clients for free. These are typically used for process design and plant optimization studies. For example, BASF developed ISOCALCTM and CYTEC Industries developed MINCHEM® and MEUMTM.Chemistry of Copper Solvent ExtractionLiquid–liquid extraction involves the selective transfer of a substance between two immiscible liquid phases by controlling the relative solubility in each phase. In the case of copper SX, the exchange is typically achieved by an oxime-based chelating mechanism. In particular, mixtures of aldoxime and ketoxime are normally used in conjunction with modifiers. More detail on this extensive topic can be found in Schlesinger et al. (2011)."

Jan 1, 2015

By A. Hosseini

Full-scale rupture tests were conducted on 508 mm (20 in) diameter API X-60 5.7 mm wall thickness pipes containing either axial semi-elliptical cracks or simulated corrosion defects with equivalent depths ranging from 20 to 60 percent thickness. In the case of the cracks, the failure pressures were predicted with reasonable accuracy when considering a level 3 failure assessment diagram (FAD) procedure based on API 579, as compared to level 2 FAD, since the mechanical properties were known. In both cases, the accuracy improved for shallower cracks. Considering simulated corrosion defects, the RSTRENG approach provided more reliable results on predicting the collapse pressure. For a similar depth and profile, the cracked pipes failed at a lower pressure than those containing simulated corrosion defects of equivalent depth.

Jan 1, 2010

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By J M. Marwan, B Tang

Strain-type rockbursts, or strainbursts, are characterised by a localised violent failure. Their cause is attributed primarily to the sudden release of strain energy, which accumulates in a volume of highly stressed rock as a result of mining activities. Examples of such phenomena are crown/sill pillar bursts created in the mining process, pillar crush in room-and-pillar mining, face ejection in drift development headings at depth, and floor bursts associated with deep shaft sinking. The paper describes a simple method for the assessment of crown pillar bursts in steeply dipping ore deposits which are extracted by the overhand cut-and-fill method. The method is based on a theory previously established by the author to help assess the need for a remedial solution such as pillar destress blasting. Basically, the mining-induced energy storage rate (ESR) in the pillar is compared with the critical strain energy to come up with the so-called burst potential index (BPI).

Jan 1, 2001

By Rolf Andreas Lauten, Guy Kluck

"Formation of scales may have important detrimental effects in many mineral processing applications. A well-known problem is the need for frequent maintenance to remove scale from processing equipment. Another challenge may relate to encapsulation of valuable minerals in precipitating scale. In this work, we explore the ability of some crystal growth inhibitors to prevent or lower the degree of scale precipitation. In many situations pregnant leach solutions contains substantial concentrations of calcium, magnesium, sulfate and carbonate in addition to dissolved valuable elements, e.g. gold, copper, zinc. Together with non-dissolved gangue minerals, some slurries may also contain particulate gold, copper etc. During normal processing of the pregnant leach solution it may be exposed to temperature gradients or similar promoting precipitation of various scales. Valuable minerals may become entrapped in precipitates and thus become inaccessible to the lixiviant. Use of a crystal growth inhibitor may lower the degree of encapsulation of valuable elements.Using a simple model system, supersaturated with respect to gypsum, the effect of some crystal growth inhibitors on the prevention of scale is evaluated in terms of amount precipitated gypsum, the particle size of the precipitated gypsum and the carbon gold loading capacity.INTRODUCTIONGold bearing sulfide ores are often roasted or pressure oxidised prior to leaching. The purpose of this unit operation is to prevent loading the leaching circuit with sulfides that consume cyanide. Pressure oxidation or roasting chemically converts the sulfides into sulfates and at the same time, the pH of the slurry ends up in the acidic range. Typically, lime addition is the preferred means to raise the pH to around 10 where gold leaching takes place. Combination of large amounts of calcium ions from the lime with sulfate ions from the ore induces precipitation of gypsum. Compounds like calcium carbonate may also precipitate if carbonate ions are present in the slurry. Depending upon the composition of the ore, compounds like calcium carbonate and other types of scale may also precipitate on gold surfaces on the slurry particles. A layer of scale on top of exposed gold surfaces will prevent dissolution in the cyanidation that takes place during leaching. Naturally, such a precipitation may lower the gold recovery."

Jan 1, 2016

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

By D. Shin

The gold leaching using cyanide from ore or waste has been almost universally in use [1]. Recently, biological gold bioleaching using cyanide producing bacteria, e.g. Chromobacterium violaceum, Pseudomonas fluorescens, or P. aeruginosa, has been investigated as environmental friendly and cost effective method. Among them, C. violaceum has been reported as effective cyanide producing bacterium on gold leaching [2, 3]. C. violaceum produces cyanide using glycine as a direct precursor and subsequently detoxify the cyanide by ß-cyanoalanine synthase [4]. However, until today only 0.026 ? 16.9 mg/L of cyanide production in YP medium has been reported in the literatures by C. violaceum [4-6]. Comparing with adding cyanide chemical, biogenic cyanide concentration is lower than the cyanide concentration added in traditional cyanidation. Since cyanide also forms complexes with a number of other elements such as iron, nickel, zinc, silver, copper, and platinum, it is very important for gold recovery to investigate the enhancement of biological cyanide production and set optimal experimental condition. Most of early studies on gold bioleaching by C. violaceum have been performed to investigate gold leaching mechanism using gold powder, and recently various resources such as ores, electronic scrap, and printed circuit boards of waste electronics [7]. Few studies have dealt with gold bioleaching from low-grade ore. In this research the feasibility of gold bioleaching by C. violaceum from low-grade ores containing gold was evaluated and fundamental study was performed for further scale-up study. The aim of this study was to improve the potential of gold bioleaching by C. violaceum from gold-containing ore; in particular, enhancement of biological cyanide production.

Jan 1, 2012

By Grady B. V O, Cavell K. J, Ault A. R, Newman O. M G, Malcolm J. McPhersqn

Cyclic voltammetry (CV) has been evaluated as a technique for monitoring the quality of an industrial zinc sulphate electrolyte. The basis of the method involves measuring a change in the polarisation of the zinc nucleation reaction at an aluminium surface and relating this to the impurity content and/or the overall quality of the electrolyte. Specifically, the technique aims to be able to indicate and quantify detrimental synergism between impurity elements, something which traditional analytical techniques are incapable of providing. The technique has found some success with regard to monitoring glue additions in a range of metal electrolytes. It has been found that investigations by a number of workers over the past 15 years have produced variable and often misleading results due to the inadvertent use of commercial purity aluminium working electrodes. It has been shown that impurity elements in the working electrode can give rise to a range of responses that are not obtained when pure aluminium is used and that the response is variable due to the lack of surface homogeneity of commercial purity aluminium electrodes. Furthermore, it was demonstrated that previous detection limits reported in the literature were based on the presence of additional peaks in the cathodic scan and not polarisation effects. The results of this study have shown that when a pure aluminium working electrode was used, the method was incapable of detecting any change in polarisation for an electrolyte containing three common impurities (Co, Ni and Ge), at concentrations that would significantly reduce optimum electrolytic performance. A range of methods was tried to sensitise the technique, including raising the temperature and acidity, and adding antimony in order to induce some synergism. In all cases the polarisation response was unchanged. Consequently, apart from the commercialised application for monitoring additions of antimony and levelling agents such as glue, CV has very limited application as an electrolyte screening technique.

Jan 1, 1993

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

By M. A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

Jan 1, 2009

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

Unlike other types of mining accidents, where an incident generally involves only a few workers, the danger of a mine fire extends to every person working in the underground environment. Mine fires can trap or kill those working underground by blocking avenues of escape and rapidly creating heat, asphyxiating gases and toxic fire products that can quickly spread throughout the mine. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate and improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Because wood is the second most abundant fuel available during a coal mine fire, it was decided that a series of large-scale wood crib fire tests was needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.1

By G. J. Koons, J. L. Uhrie

Field density studies carried out at the Phelps Dodge Chino Mine have found that truck-induced compaction is limited to the upper 2.4 m (8 ft) of an individual lift. Hydraulic properties of material compacted to field densities were determined in a laboratory setting. Saturated flow models were then run, simulating the effect of compacted zones within a stockpile. Modeling shows that compaction can prevent solution flow through large portions of the stockpile. This implies that care must be taken to ensure that ripping is carried out to a depth of at least 2.4 m (8 ft) across the entire stockpile to achieve uniform solution flow. Uniform solution flow will result in maximum leach recovery.

Jan 1, 2002

By Ahmed H. Bukhary, Naser A. Al-Shayea

The objective is to assess the overconservatism in the parameters used for designing offshore piles. Methodology includes analysis of shaft friction data obtained from more than five different locations in the Arabian Gulf, consisting of 40 piles to depths up to 86 m. Reports were collected for both the dynamic pile monitoring system (DMS) and their corresponding geotechnical reports based on the American Petroleum Institute (API). The values of shaft capacity for the sand layers were analysed by comparing those based on API to the corresponding DMS values. Results of the comparison of the data from these reports showed that the pile design parameters obtained using API guidelines is generally smaller than that measured by DMS. The difference is presented in terms of an overconservative factor (OCF) which is adjusted based on statistical nonparametric test performed on the two data sets. The adjusted OCF were found to be 1.79 and 2.00 for carbonate sand at (loose to medium dense) and (dense to very dense) conditions, respectively. The corresponding values for silica sand were only 1.2 and 1.06. In conclusion, based on the evaluation conducted for data from these reports, the API shaft friction is overconservative for carbonate sand. The API shaft friction for piles in sand can be increased by multiplying it by the adjusted OCF.

By L. C. Bird, A. I. A. Salama, M. W. Mikhail

"A program of sampling in Canadian washeries was carried out by the Coal Research Laboratory (CRL) over a period of two years to evaluate the performance of various density separators in these operations(1). Operating data on quality and recovery of products, separation efficiencies and cutpoints for each separator type are compared with data predicted using computer models developed from previously existing data.The Heavy Medium Cyclone (HMC), Heavy Medium Bath (HMB) and jig models give predictions of recoveries and qualities of products for sizes coarser than 10mm with absolute value of error mean less than 7 per cent, whereas predictions of the Water Only Cyclone (WOC) model for -10mmfine coal are with absolute value of error mean less than 8 per cent. Although less accurate for -10 mm fine coal, the HMC and jig models produce predictions of recoveries with absolute value of error mean less than 2 per cent and quality of products predictions with absolute value of error mean less than 28per cent which are generally acceptable because more liberation in the fine fractions appears to compensate for any difference in the accuracy of separation, resulting in good prediction of the clean product. However, ash content of the actual fine refuse was lower than predicted. The difference is attributed to the highly friable nature of Canadian coals which tends to cause an excessive loss of coal fines to the fine refuse.A comparison study based on quality and recovery of products is made between the Dutch State Mines (DSM) models and the recently modified models, both produced comparable predictions."

Jan 1, 1985