Search Documents

By Anne Kvithydl

Printed circuited boards contain considerable quantities of valuable metal, while also containing many environmental pollutants making them unsuitable for landfill. In this study the decomposition of common plastics used in printed circuit boards were studied. Polytetrafluoroethylene (PTFE), polyvinyl chloride (PVC) and polyethylene (PE) were heated in both CO, and argon atmospheres using a thermo-gravimetric furnace (TG) coupled to a mass spectrometer (MS). Soda ash Na,C03 and baking soda NaHC03 were used as reactants. The degradation temperatures and evolved gases are presented for single plastics and mixtures. Mixed plastics are shown to behave as a sum of the individual plastics. The mass loss temperature is the same in CO, and argon. However, less residue is formed when heated in CO,.

Jan 1, 2008

By M. G. Ayat, B. C. Scott

Coal degradation is the breakage of coal particles to finer sizes due to the continuous forces of attrition and gravity to which coal is subjected during mining, handling, and preparation. The objective of this paper is to determine the extent of degradation that a coal slurry experiences when transported through pumps and pipelines. The examination of degradation results for a number of different coal slurries have indicated that the extent of breakage is dependent on the physical properties of coal and the time span of circulation. These results have also indicated that certain size fractions of coal are more susceptible to breakage than others.

Jan 1, 1987

By M. G. Ayat, J. Dasher

Having an interest in coal slurry pipelines from a decade of arguments with Ed Wasp and crew at Bechtel about pumping thicker slurries slower, I immediately read this article and found nothing in it pertinant to the title. Ayat and Scott pumped five unidentified coals at 9% solids (50%-60% is the area of interest) in a 25-mm (1-in.) pipe around two square elbows through a 76-mm (3-in.) cyclone for up to 60 minutes and sized a large number of samples of unstated size on an unidentified wet screening device. They did not measure power consumption, discharge pressure, flow rate, or give pump tip speed or impeller diameter. They siad the cyclone had a "high" pressure drop (unmeasured) and did much of the degradation (measured) but more or less per unit of energy expended? Hargrove was not measured, so there are no data as to whether it would correlate with degradation. The authors conclude, with no attempt, correlation is "hard to establish." Please experiment before concluding. I am at a loss to know what "increasingly smaller size" means, much less what theory says such particles take "exponentially larger quantities of energy," which the authors neglected to measure. If such experiments without pertinent data or justified conclusions must be published, please attach a pertinant title.

Jan 1, 1990

By M. G. Ayat

I have been following the discussions on coal degradation started by the article "Degradation process in coal slurry pipe-lines," by M.G. Ayat and B.C. Scott. I agree with Mr. Dasher's comments in January that the title of the article was perhaps misleading as the information appeared to pertain more to processing the coal than to transportation. Specifically, the authors' conclude that the cyclone had an important impact on the degradation. Dr. Ferri's comments on degradation in other physical processes was very correct, handling of coal in a turbulent manner has an impact on the size distribution of the coal. This is one reason that when I design a coal system (mine to rail car) I try to minimize the total number of transfer and processing steps consistent with achieving the desired product specifications. Another area, mentioned in passing in the article, the impact of natural causes and the mining step, is of particular interest to me. A mine in West Virginia had a variation of 50% in the -6.35 mm (-0.25 in.) raw coal depending upon the direction of mining. Since it was a single unit mine, this significantly impacted the final product. Two articles on mining's impact on size distribution are: • Stefanko, R., Chopra, I. K., and Ramani, R. V., 1974, "Mining influence on size consistency and washability char¬acteristics of coal," SME Fall Meeting. September; and • Albrecht, M., and Olsen, D., 1980, "Mining methods impact on coal preparation plant design." 1st International Mine Planning and Development Symposium. September. Both articles presented information on variation of size distribution and cleaning plant performance on a coal depending on the mining method used. Both articles considered a single coal seam at one mining operation. Stefanko's article considered continuous and conventional mining of coal in Pennsylvania. Albrecht's article considered surface, underground continuous, and underground hydraulic mining of a coal in British Columbia. Both concluded that mining methods do impact coal characteristics. I agree with Mr. Ayat's comments in reply to Dr. Ferri's discussion, "... degradation is a multi-faceted phenomenon involving many natural and man-made factors." As efforts are being made to produce a higher quality (lower sulfur) coal, this topic becomes even more important

Jan 1, 1990

By Fábio de Oliveira Braga

A descoberta de óleo e gás no Pré-Sal transformou o Brasil em um dos grandes possuidores de reservas de petróleo no mundo e aumentou as expectativas de produção em águas profundas. Apesar da euforia, alguns desafios têm o potencial de inviabilizar a exploração do Pré-Sal: a complexa logística offshore, as dificuldades de acesso ao reservatório, as condições físico-químicas do poço e de subsuperfície. As condições impostas pelo ambiente são relevantes, devido aos altos teores de contaminantes, alta temperatura e pressão, que exigem materiais de alto desempenho. O objetivo deste trabalho é revisar os avanços que podem contribuir para superar as condições físico-químicas do Pré-Sal. Verificou-se que a solução deste problema pode envolver três tipos de abordagem: O desenvolvimento de ligas resistentes à corrosão (LRC), a adição de agentes modificadores do meio corrosivo (inibidores) e modificações no projeto dos equipamentos. Espera-se, portanto, que a utilização conjunta das diferentes abordagens proporcione a viabilidade de longo prazo da produção no Pré-Sal.

Aug 17, 2017

By Luís Marcelo Marques Tavares

Pelotas de minério de ferro representam uma parcela significativa do mercado transoceânico de minério de ferro, contando com uma participação importante de empresas brasileiras. Pelotas concorrem favoravelmente com granulados e sínteres de minério de ferro na carga metálica de fornos, em particular devido à sua elevada resistência à degradação durante o manuseio e transporte. Entretanto, pelotas ainda sofrem desse problema, que resulta na geração de finos, removidos previamente à alimentação do forno, ou de cacos, que podem resultar no aparecimento de clusters em fornos de redução direta. Esses efeitos danosos da degradação podem ser minimizados caso uma metodologia adequada de caracterização de pelotas e de simulação do processo de manuseio se encontrasse disponível. O presente trabalho trata do desenvolvimento de metodologia inédita e inovadora para previsão de resultados de degradação de pelotas, desde a usina pelotizadora até o pátio ou forno do cliente, desenvolvido como parte da parceria entre o Laboratório de Tecnologia Mineral da COPPE/UFRJ e a Samarco Mineração. O trabalho mostra ainda uma validação preliminar a partir de um ensaio de quedas múltiplas em laboratório, mostrando ótima aderência. Um simulador do processo foi desenvolvido, o qual permite inserir as características das pelotas produzidas, bem como o fluxograma de manuseio, permitindo prever a intensidade da degradação.

Aug 16, 2017

By Luís Marcelo Marques Tavares

Conforme apresentado na parte 1 do artigo, uma metodologia inédita de previsão de resultados de degradação mecânica de pelotas, desde a usina pelotizadora até o pátio ou forno do cliente, foi proposta, resultando no desenvolvimento de um simulador do processo, o qual permite inserir as características das pelotas produzidas, bem como o fluxograma de manuseio. A fim de demonstrar a utilidade já encontrada pela Samarco na aplicação do simulador, três estudos de casos foram apresentados: no estabelecimento, junto a um cliente, da faixa de tamanhos ótima das pelotas a serem fornecidas, que permitiu o aumento da sua resistência à degradação, minimizando os custos de produção; no auxílio à tomada de decisão em um projeto de expansão na instalação portuária em Ponta Ubú. O último estudo de caso tratou do apoio aos esforços de um cliente situado no Oriente Médio na identificação e tomada de decisão sobre ações que poderiam minimizar a degradação dentro de suas instalações.

Aug 16, 2017

By N. Nikolaeva, A. Romashev, T. Aleksandrova

Energetic characteristics identify energy consumption for destruction of prills and kinetic characteristics rate formation of finished size grade in the course of destruction and identify crushing and grinding equipment capacity. And if screen sizing or classification processes are applied in the cycle of ore preparation, then the use of characteristics of separation to size – separating characteristics – is required for theoretical description. Separating characteristics have a lower profile for ore preparation but, nevertheless, they have to be taken into account especially for balance and design calculations of crushing and grinding circuits. In most cases there are impregnations of minerals which vary widely in energy consumption and destruction kinetics and thus polyminerality must be considered as one of priority factor. Raw materials which passed through crushing and grinding processes can be assessed numerically by functions of fractional composition of two types: differential distribution function y ( €) and assay function B( c ) . A set of experiments on grinding of crushed raw materials at different time (up to various sizes) was conducted to analyze effect of grinding size of carbonaceous overburden on function y € and B ( c) as well as to justify the possibility of preconcentration of raw materials at the stage of ore preparation. Analysis of metals distribution per size grades showed that metals are concentrated in size grades of less than 0.315 mm (which is equivalent of cut point for this type of raw material), however, there is no overgrinding and oversludging of material, and enriched product for its further processing can be excluded with the help of classification. The stage of size segregation was tested as a method of preconcentration of raw materials for optimization of ore preparation and further separation.

Jan 1, 2018

By Will Coghill

As the title indicates, this paper treats of the degree of liberation of minerals after grinding. To obtain the supporting data a "tool" not commonly used by metallurgists has been employed. It is the "heavy solution." The advantages gained through its use are shown. Actual ores were employed in order to make the study concrete. The selection was somewhat incidental and happened to embrace the red iron ores of Alabama. So, any reader interested in these ores will find some of their properties described. The red ores constituted the material examined and a somewhat new adaptation of heavy solutions was the tool of examination. If either the ores or the tool interest the reader these notes may be of some value. The writer's chief interest was in the rate of liberation of locked grains. Ores are generally ground preparatory to concentration and as long as the concentrators make suitable products the effectiveness of the grinding is likely to be unquestioned. But when suitable products are difficult to make, an investigation becomes imperative. In such a case a dissection of the ore might be made to find the cause of the trouble. Such a condition of unsuitable products exists in the low-grade red iron ores of Alabama. They are difficult to concentrate. To be sure it might be said that the concentration of iron ores is a new thing and that the ore-dressing methods are undeveloped, but a glance at the industry reveals an abundance of methods and devices for almost all imaginable conditions. Concentrating machinery has not taken a part in this investigation; the use of it would have been only machinery testing, and should never precede the ore testing which consists of such methods as herein outlined. When the properties of the ores have been gleaned the machinery may be used more effectively.

Jan 12, 1926

By Rodney Ishak, Merete Tangstad

In the HC FeMn production, better utilisation of coke and electric power is vital for reducing the production costs. The higher manganese oxides in the charge are reduced to MnO in the prereduction zone, where also the Boudouard reaction is active. These gas-solid reactions are to a large extent decisive for the total consumption of both coke and electrical power in ferromanganese production. In the present work formulas for calculating the Degree of prereduction have been developed for industrial practice. It shows that the typical Degree of prereduction is between 10-40%, but it may in good periods be as high as 60%. Statistical analysis has been done in order to find how various operational parameters influence the Degree of prereduction. A few parameters were observed to have an effect on the prereduction. Comilog ore definitely had a positiveinfluence on the prereduction, Comilog sinter and Mamatwan ore probably had a positive influence on the prereduction, all in relation to the average prereduction in the selected periods. Meanwhile, As man ore definitely, % H2O in raw materials and increasing Hd probably, had a negative influence on the prereduction. The findings for these raw materials were very much in coherence with the results of laboratory scale experiments performed, where the CO-reactivity of different ore materials was studied.

Jan 1, 2007

By U. Prasad

This paper summarizes the investigation carried out on a wide range of rock types, subjected to high velocity impact to simulate explosive action. A Split- Hopkinson Bar apparatus was used to generate the high velocity impact. The rock samples included both homogeneous and isotropic, and anisotropic types. The strain rate achieved was between 600 and 12OO/sec, The respective measured dynamic compressive strengths were compared with their low strain-rate or static values. It was found that the ratio of the dynamic to static values ranged between 2.5 and 4.6. It was also determined that the high strain-rate loading produced finer fragment size distribution than the static loading. The fragment size distribution from the two strain-rate regimes has been further analyzed to establish correlation with rock types and the strength characteristics. The results also confirm that high strain-rate loading (i.e. high detonation pressure and high velocity of detonation in an explosive column) would significantly affect the degree of fineness in a blast.

Jan 1, 2001

By M Bellamy

The DeGrussa copper deposit was discovered by Sandfire Resources in April 2009. Construction of the 1.6 Mt/a concentrator, open pit and underground mining operations commenced in March 2011 with first concentrate production achieved in October 2012. Over the next ten years, DeGrussa grew to include both the DeGrussa and Monty underground mines, establishing itself as one of the world’s premier copper producers with total production of 663 000 t of contained copper by the time the mine closed. Final ore was trucked from Degrussa on 5 October 2022. This paper examines the mine closure experience from both a planning and operational perspective. The paper provides an overview of the site’s mine planning process including the factors involved in determining the end of the mine life and how this was tracked and communicated in the lead up to the end of mining operations. It will also look at some of the specific operational aspects involved in maintaining steady state production all the way through to the last day while facing increasingly challenging conditions. These factors, along with the external factors faced by most of the industry such as labour shortages and COVID related disruptions, contributed to making it an interesting journey to the end of operations at DeGrussa.

Mar 29, 2023

By P Vass, C Butler, J Condon, B Hooper

DeGrussa Copper Mine, resource status 10.2 Mt at 5.7 per cent Cu, 2.1 g/t Au (Sandfire Resources, 2013), commenced concentrate production through its 1.5 Mt/a conventional copper flotation processing plant in September 2012. Geometallurgical assessment during the feasibility study identified potential process-critical ore factors that required further investigation to determine potential impact on processing. Ore characterisation and metallurgical processing performance test work of ore types ensued and subsequently, the first quantitative DeGrussa geometallurgy model was born. Now one year into steady state production, the geometallurgical program has evolved significantly from its infancy and provides valuable insight into ore characterisation and behaviour in the processing plant. This paper details geometallurgical investigations undertaken at DeGrussa to date; from feasibility metallurgical test work through to geometallurgical modelling and management practices, as well as reconciliation between observations at feasibility study level and subsequent observations in production.CITATION:Condon, J, Butler, C, Hooper, B and Vass, P, 2013. DeGrussa Copper Mine, Western Australia - feasibility to first production: a case study in developing a working geometallurgy model from first principles, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 59-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By P. D. Rao

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. Coals from Usibelli Coal Mine and the Beluga coal field have a heating value of approximately 8,000 Btu/lb and 28% moisture. Hydrothermal treatment (at 275 to 352'C) of lump coal from Usibelli Coal Mine and Beluga coal field enhanced the heating value of the coal, on an equilibrium moisture basis, from 8,000 Btu/lb to nearly 12,000 Btu/lb. The product coal with high heating value and 0.2 % S is an environmentally acceptable premium fuel. The Hardgrove grindability index of the coal is greatly improved, further enhancing its value. Increase in hydrothermal drying temperature promotes vesiculation of resinite. Vitrinite reflectance increased to 0.72 and vitrinite was subjected to widespread visiculation resulting in a coke like structure indicative that the material went through the fluid stage.

Jan 1, 1991

By W. G. Willson, Y. L. Li, P. D. Rao, D. E. Walsh

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. The objective of this study was to subject two Alaska low-rank coals to hydrothermal drying to enhance their marketability in the Pacific Rim markets and to evaluate the chemical and physical properties of the dried products as a function of process conditions. Coals from Usibelli Coal Mine and the Beluga coalfield have a heating value of approximately 18.5 MJ/kg and contain about 28% moisture. Hydrothermal treatment (at 275° to 325° C) of lump coal, from the Usibelli Coal Mine and the Beluga coalfield, enhanced the heating value of the material, on an equilibrium moisture basis, from 18.5 MJ/kg to nearly 27.8 MJ/kg. The product coal, with a high heating value and only 0.2% S, is an environmentally-acceptable premium fuel; additionally, with the Hardgrove grindability index of the coal greatly improved, its value is even further enhanced. An increase in hydrothermal drying temperature promotes vesiculation of resinite. Also, ulminite reflectance increased to 0.92%, and ulminite was subjected to widespread vesiculation; this resulted in a coke-like structure indicative that the material went through the fluid stage.

Jan 1, 1993

By J. Oré

An alternative method for dewatering slurry (tailings) is the use of geocontainers (MacTubes). The practical application of this work was carried out in the concentrator plant of the Raura Mining Company, located in the occidental mountain between Huánuco and Lima in Peru?s central highland. For the development of the research, the MATLAB R2012a software MGeST (v. 1.0) was used (Slurry Geocontainer Maccaferri Treatment). MGeST is used for sizing MacTubes, which allows determination of the most important design parameters, such as height (H), filling residual pressure (P1O ), strength of geosynthetic (T), and dehydration height. Compared with GeoCoPS v. 3.0, there is a maximum difference of 3% between the results obtained. The tailing to be treated in the MacTube have a specific weight of 11.62 kN/m3. After several tests it was determined that a MacTube of an apparent opening size of 0.22 mm was required for this specific weight.

Aug 1, 2013

By B. N. Whittaker

The paper briefly reviews the type of support and stability problems encountered in mining tunnels in U.K. Carboniferous rock conditions, particularly the Coal Measures where almost all such tunnels are located. Stability prediction of mining tunnels is discussed and a computer-based model which deals with stratified rock conditions is described. Various schemes for monitoring the stability of mining tunnels are examined and the application of the results discussed. Comparisons between predicted and measured Closure values are presented for a major Coal mining tunnelling project at Selby in the North Yorkshire Coalfield. Conclusions are drawn concerning the application of the present prediction technique together with the importance of underground monitoring. Examples of different types of mine tunnel stability problems encountered in the U.K. Coal Measures are discussed and comments made on the secondary effects of tunnel peripheral rock weathering and corrosion of the associated support systems.

Jan 1, 1987

By John A. Christophersen, Adolf J. Jonaitis

Coal flotation applications utilizing column flotation have been shown to improve grade and recovery when compared with traditional mechanical cell flotation. Deister Flotaire Column Flotation Machines have been installed in pilot and commercial coal cleaning applications. Comparative data covering prior and current flotation is presented. In addition, special characteristics covering the Deister air generation system are presented.

Jan 1, 1989

By Francisco Raunelli

Anglo American Quellaveco S.A. perteneciente a Anglo American PLC, construyó las bases de la aceptación social del proyecto Quellaveco, (Moquegua) después de un largo proceso de relacionamiento social (comunitario, institucional). En ese sentido, el presente texto describe el proceso de la Mesa de Diálogo con participación del sector civil, autoridades y Anglo American, que buscó consensos para el desarrollo de Moquegua. Así el diálogo, la transparencia y la generación de confianza se ven fortalecidos mensualmente con la participación de Anglo American en las reuniones de la Comisión, donde se decide y se informa del trabajo y avances desarrollados para el cumplimento de cada uno de los compromisos asumidos. Así también se adelanta el cumplimiento de algunos de ellos considerados como prioritarios para la población, ya que los compromisos están asignados para diferentes etapas de la mina (preconstrucción, construcción, operación y cierre).

Apr 1, 2015

DeLamar, the largest silver mine in the United States outside the Coeur d’Alene District in Idaho, came into production in April 1977. It is a joint venture of Earth Resources Company and Canadian Superior Oil Co., with Earth Resources being the operator. The property is a consolidation of several old operations dating back to the 1800s; the better known of these are the DeLamar and Sommer-camp mines. DeLamar is situated in southwestern Idaho near the Oregon border in the Owyhee Mountains, 88 km (55 miles) southwest of Boise, Idaho. Heavy snowfalls and very low temperatures are common in the wintertime. Planned production was 77,500 kg (2.5, million oz) of silver and 5 13 kg (16,500 oz) of gold per year. Expected life at a milling rate of 1,540 mtpd (1,700 stpd) was 20 years, with an ore grade of 144 g Ag and 1.58 g Au per mt (4.2 oz Ag and 0.046 oz Au per st). Present production is at the rate of 1,900 mtpd (2,100 .stpd). The total cost to bring the mine into production was reported to be approximately $22 million, and the mill was reported to have cost about $10,000 per daily ton of design capacity. At DeLamar, naurnanite (Ag2Se) is the principal silver .mineral occurring with acanthite (Ag2S) disseminated through quartz veins and a silicified rhyolitic ash-flow tuff of Miocene age. The mineralization is relatively iron and manganese free and is readily amenable to cyanidation giving recoveries of 85% silver and 92% gold, which occurs free. When the plant was started, considerable difficulties were encountered in handling the wet sticky ore because of the high clay content. Following primary crushing, the ore is stockpiled. Due to the sticky nature of the ore, the vibrating feeders initially installed under the stockpile were replaced by a reclaim hopper and an apron feeder which was fed 24 hours a day by a front-end loader. The minus 200 mm (8 in.) ore is fed to a 5.5 m by 2.75 m (18 ft by 9 ft) autogenous mill followed by a 2.75 m by 4.57 m (9 ft by 15 ft) ball mill and cyclones. The mills are equipped with 750 kw and 520 kw (1,000 hp and 700 hp) motors. Both mills discharge to the same cyclone feed sump and a portion of the cyclone underflow is returned to the autogenous mill. Cyclone overflow, which is 20% plus 74 microns (200 mesh), is leached in four agitators in series for 72 hours (45 hours at the 2,100

Jan 1, 1981