Search Documents

By E. S. Smith, Sunirmal Banerjee

INTRODUCTION Social awareness of the detrimental impact of man-made wastes on our environment has grown considerably during the last two decades. Increased public and institutional concerns have resulted in the implementation of a wide variety of regulatory controls of disposal of wastes. These regulations have often reflected significant conservatism in expecting guaranteed elimination of pollution risks. This sort of expectation assumed a state of knowledge which was not readily available to the major producers of wastes. The mining industry, in particular, has been affected by such regulations in terms of excessive costs and loss of benefit. As a result, investigations are in progress (1) to generate newer methods for satisfactory stabilization of mine and mill wastes and (2) to apply the available technology to achieve the standards set by the regulatory agencies at reasonable costs. This paper presents a conceptual scheme for stabilization of mill wastes by suitable management of operations and accelerated consolidation of tailings slurries. The main discussion in this paper is aimed at the ability of the proposed scheme to address the major considerations in effective disposal. Comparison in both cost and effectiveness are also made between the proposed scheme and various other currently used disposal concepts. MAJOR CONSIDERATIONS IN EFFECTIVE DISPOSAL The primary objective of an effective tailings disposal scheme is to provide containment of the contaminants in such a manner that the undesirable impact of the wastes on the three basic elements of our environment--land, air, and water-would be minimal. Bearing the above objective in mind, one may justifiably list the major considerations in the choice of the disposal scheme in terms of its effects on land, air, and water (Bromwell, 1976) as follows: Effects on Land (1) whether the scheme makes optimal use of land.

Jan 1, 1980

By P. Hale

"The trend to drives of more than 10,000 hp on large-capacity ball and autogenous mills for increased operating efficiency has been limited by factors in the conventional drive system. A solution to this problem, using modern developments in static converter technology, is the concept of driving the mill directly without gearing using a low-speed, low-frequency synchronous motor with a cyclo-converter power supply.This paper presents various practical arrangements of mill and low-speed motors giving the specific advantages of each system. The means of controlling inrush currents on starting and of spotting by the use of variable-frequency control are outlined in general form. Several gearless ball mill drives are scheduled for start-up in European cement plants and further orders have been placed."

Jan 1, 1970

Geosynclines have been well studied for many years, but very little has been written about the concepts of sedimentary basins in spite of the vast amount of data available. They have been regarded, perhaps, as well- understood intuitively, and therefore not worthy of study. Many of the fundamental concepts of geology were developed during the 19th Century with the construction of coal mines, canals and railways. It was a happy chance that led railway engineers in the early days to think that trains could not climb any but the smallest gradient, so, in Britain at -least, numerous railway cuttings and tunnels were made. These exposed to view and study, in a better form than Nature usually provides, a great deal of interesting geology. Because of the lack of literature about the concepts of sedimentary basins, it is not possible to be sure what the early geologists thought. It seems that sedimentary basins were regarded as recording a history of subsidence during the early stages, when a transgressive sequence accumulated; and a history of uplift during the later stages, when a regressive sequence accumulated. It seemed axiomatic that the age of folding and faulting was younger than the rocks folded or Faulted.

Jan 1, 1987

High sulphur volcanic-hosted hydrothermal environments are favourable geological environments for gold mineralisation. Numerous world-class gold deposits including Pueblo Viejo (Dominican Republic), Goldfield (Nevada), EI Indio (Chile), and Wa

Jan 1, 1994

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By Roberto J. Guardia, Robert A. Robinson, John Wilkerson, Wick Haxton

Several candidate sites have been proposed for the Deep Underground Science and Engineering Laboratory (DUSEL), a facility that would provide over 2000 meters of overburden to screen out cosmic rays that would otherwise interfere with experiments. Types of anticipated experiments include: detection of dark matter and stellar neutrinos, and evaluation of deep microbial life forms. Engineering experiments might include more refined scanning devices to “see” rock defects ahead of tunneling, improved predictive models for groundwater inflows and tunnel support requirements, and improved instrumentation for monitoring in-situ stresses, rock deformations, and pore water pressures. Spin-offs from this research might include more sensitive security detectors for scrutinizing shipping containers, new drugs based on new microbes, and improved sensor systems for tunneling. A site near Leavenworth, WA, was assessed and shown to have numerous topographic and geotechnical advantages. Rock cover is on the order of 2250 meters. The granitic bedrock is suitable for tunneling a variety of large underground openings.

Jan 1, 2005

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Lang Shiping

The criteria for designing a crushing chamber are presented and a program for designing the shape of the chamber is proposed. During the chamber shape design, major design parameters are analyzed first, optimized parameters are determined next and the basic shape of chamber is figured out finally. In the basic chamber design program, the influence of abrasion of basic chamber shape and material characteristic are not accounted for usually. Here, based on the minimum abrasion of chamber shape and uniform particle size theory, the equation for chamber surface curve and the transcending function were formulated and a low-abrasion chamber was designed. Since the chamber shape designed based on experience and experiments is not necessarily the best, optimal design of the crushing chamber shape was carried out. Cubic spline function was used to represent the chamber shape curve and a mathematical model was formulated. The optimal shape solution was obtained using a complex method. Finally, the optimal chamber shape was determined by matching the moving cone stroke S, moving cone speed N and the moving cone bottom angle Thus, superior technical performance of the cone chamber was achieved.

Sep 1, 2012

By J. F. Mahoney, P. B. Hobsbawn, N. Arbiter, C. C. Harris

Current trends in flotation applications are reviewed and effects of increased cell sizes and automation of circuits considered. The role of laboratory and pilot plant investigations in establishing design criteria and project feasibility are assessed and illustrated.

Jan 1, 1978

By Jon Y. Kaneshiro, Donald W. Scapuzzi

The primary purpose of the Prototype Installation Facility (PIF) for the Superconducting Super Collider (SSC) in this conceptual design was to test the magnets and other physics equipment. PIF was located in the northwest quadrant of the SSC 54 mile (87 km) main ring and consists of the first segment of tunnels, approximately 17,060 lineal feet (5.2 km) of 12 foot inner-diameter (ID) (3.7 m) tunnel, three 250 ± foot (60 m) deep shafts, connecting tunnels, and associated niches and alcoves. PIF would be the first portion of the main ring collider tunnel to be constructed. The geology, underground excavation conditions, underground facilities, and contractual considerations are discussed.

Jan 1, 1991

By D A-F Batchelor

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.South-East Asia represents the world’s most productive tin province, mainly from placers. Kalimantan has been a major diamond producer, while in the 1980s a placer gold rush occurred in Indonesia and Malaysia. Reviewing extensive geological and mining data highlights phenomenal palaeo-environmental changes in the Sundaland region, interpreted to be responsible for generating ‘giant’ placers. Correlation of the Late Cainozoic stratigraphy has been facilitated from mine exposures and drill holes distributed throughout Peninsular Malaysia, the Indonesian Tin islands and Kalimantan, including contiguous marine areas with extensive shallow seismic profiling data. Knowing the association of rich placers with palaeo-environmental episodes and stratigraphical units has been helpful to facilitate their discovery. All three placer commodities responded similarly to region-wide landscape evolution following Mio-Pliocene high sea levels. Commencing with major regression, important stages comprised: a long period of landscape stability with deep weathering during the maximum Sundaland extent gradually rising sea levels/precipitation initiated slumping of mineralised regolith to form fans, later reworked by braided streams with aggradation (Old Alluvium); during episodic pluvial periods downcutting upgraded placers significant change occurred around Middle Pleistocene time with peneplanation and pedogenesis from Late Pleistocene time ‘modern’ fluviatile deposition (Young Alluvium) filled incised V-shaped valleys.Placer seams show systematic variation in stratigraphic position, in particular cassiterite especially occurs in the Old Alluvium (equivalent Upper Dahor Formation in Kalimantan). Gold is commonly richer in gravelly younger deposits, partly because of secondary precipitation within permeable alluvium. Reworked diamonds are predominantly concentrated especially in younger fluviatile alluvium.CITATION:Batchelor, D A-F, 2015. Conceptual exploration for tin, gold and diamond placer deposits in ‘Sundaland’ (Indonesia and Malaysia) by understanding the late Cainozoic stratigraphic context, in Proceedings PACRIM 2015 Congress, pp 499–506 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"Abstract-A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995

By David S. Cronan

The traditional method of deep sea manganese nodule exploration is to conduct grid survey and sampling on successively finer scales until a suitable deposit has been delineated. Clearly this is both time consuming and ultimately self-defeating if large areas of the ocean floor are to be explored on a human timescale. A conceptual deductive approach would be preferable if one could be found, as it would aim to outline areas of potentially economic nodules on the basis of easily measurable oceanographic parameters. An attempt to achieve this aim in the Central Pacific is outlined below. Nodule Distribution in the Central Pacific Ocean Maps of ore grade nodules in the Central Pacific show that they are confined to two zones trending roughly east-west which are well separated in the eastern Pacific but which tend to converge towards 170-180ºW. They follow the isolines of intermediate biological productivity in the surface waters, strongly suggestive of a biological control on their distribution. Within these zones the nodules preferentially occupy basin areas. Thus they are found in the Penrhyn Basin, Tokelau Basin, Central Pacific Basin, Clarion Clipperton Zone and Tiki Basin. Nodules in all these areas have features in common and are thought to have obtained their distinctive composition by similar processes.

Jan 1, 2003

By John L. Watson

A conceptual model (MAGSEP) is described to simulate the beneficiation characteristics of a drum magnetic separator in terms of the probability of an individual grain being recovered in the magnetic concentrate. This probability is determined as a function of particle magnetic composition and magnetic field strength and is modified by particle size and the separator operating conditions. The model predicts the size, magnetic grade and distributions of magnetic and gangue minerals in the concentrate and tailings produced by the drum separator. The configuration of the magnetic concentration circuit may be altered to permit single or double drum units in parallel or series operation. The characteristics of the feed material, in terms of a magnetic parameter, are essential in permitting the determination of individual grain recovery probabilities upon which the model is based. Thus the model requires input data relating to the distribution of composite grains in terms of magnetic grade and particle size. To illustrate the use of the conceptual model an example is given for the beneficiation of New Zealand iron sands.

Jan 1, 1984

By Andre Vien, Marc Grondin

For many years mill operator training was an informal process which involved senior operators training junior operators on an as-needed basis. The more rapid incorporation of new processing and information technologies, the goal to keep labour costs to a minimum by doing more with less, and the complexity of AG/SAG mill operation has forced companies to have a closer look at operator training. This paper describes a conceptual model of the charge of a AG/SAG mill that can be used for operator training. The conceptual model divides the charge into three regions: cascading, cataracting and toe. Mill behaviour is explained by the changes that occur in each region.

Jan 1, 1997

By Paul I. Eimon, Byron R. Berger

INTRODUCTION Epithermal silver-gold deposits form at low to moderate temperatures in near-surface environments. These deposits are found in all rock types, but historically, the most important deposits occur as veins in volcanic rocks (e.g., Creede, Colorado; Pachuca, Mexico) and as replacements in sedimentary sequences (e.g., Mercur, Utah; Carlin, Nevada). Increases in the open-market prices for silver and gold in the last few years have resulted in renewed interest in precious metals and the economic viability of large-tonnage low-grade deposits. These bulk-mineable deposits form as replacements in permeable horizons or as stockworks in the up- per parts of otherwise bonanza-type hydrothermal systems and newly recognized systems that erupted onto the surface as hot springs, fumaroles, or geysers. Large tonnage low-grade de- posits were an unconventional resource prior to price increases; however, now they constitute one of the main sources of precious metals in the United States and the importance is growing worldwide. This paper presents conceptual geologic- geochemical models of epithermal precious-metal deposits derived from studies of productive deposits throughout the world. Much of the data presented is not new. However, the interpretation of the data in terms of current concepts of hydrothermal processes is new. This paper deals with idealized and general ore-forming mechanisms, and no attempt is made either to explain the origin of the different chemistries of ore- forming fluids or to examine all of the variations in specific deposits due to local structural controls and host-rock compositions.

Jan 1, 1983

In November 1969, New Zealand Steel Ltd pioneered the commercial use of the SL/RN solid fuel direct reduction process to make sponge iron as a feed material for electric arc furnaces. Serious process problems with the use of green balls and coal injection were progressively overcome. The process was developed by New Zealand Steel along a radical route, of feeding the fine grained raw ironsand concentrate and coal directly to the kiln. Contemporaneously with this development of direct reduction, steelmaking process innovations were made that enabled the arc furnaces to operate successfully with the high volumes of acid slag. The further expansion of New Zealand Steel's primary steelmaking capacity to replace the currently imported hot and cold flat rolled products is under consideration. The requirement to produce about 600 000 tonnes of steel slabs will be an opportunity to further modify iron and steel making plant and processes to optimise the economics. The conceptual and preliminary engineering selection of options is described.

Jan 1, 1980

By C. P. BATES

In November 1969, New Zealand Steel Ltd pioneered the commercial use of the SL/RN solid fuel direct reduction process to make sponge iron as a feed material for electric arc furnaces. Serious process problems with the use of green balls and coal injection were progressively overcome. The process was developed by New Zealand Steel along a radical route, of feeding the fine grained raw ironsand concentrate and coal directly to the kiln. Contemporaneously with this development of direct reduction, steelmaking process innovations were made that enabled the arc furnaces to operate successfully with the high volumes of acid slag.

Jan 1, 1980