Search Documents

By S. Clark Komardi

Freeport Indonesia, Incorporated produces 180,000 tons per year (200,000 STPY) of 32% copper concentrate. A 111 kilometer (69 mile) pipeline transports the concentrate slurry to the sea coast. Rheology characteristics of the concentrate slurry must be monitored continuously to assure that the pipeline does not plug and that mini- mum degradation of the pipeline occurs. Factors affecting the rheobgy include particle size, percent solids, pH, and reagent additions. This paper includes a general pipeline description, slurry rheology factors affecting operations, and the problems encountered and their subsequent resolution. Six years successful operation of the worlds longest copper concentrate slurry pipeline has provided a unique insight into slurry behavior.

Jan 1, 1980

By Malcolm V. Lowry

At Balmat in northern New York State, the St. Joseph Lead Co.'s 2100-tpd zinc mining and milling operation is utilizing a unique thickener in conjunction with conventional crushing, grinding and flotation methods. From 1930 through 1962, zinc concentrates went directly from flotation to the filtering, drying and loading facilities, all of which had to operate 24 hr per day. Wide fluctuations in tonnage also had to be accommodated due to variations in the grade of ore. Many problems were thus encountered in filtering and drying, but the cost of installing a conventional, large diameter thickener could never be justified. In 1963, after thorough investigation, an unconventional thickener that is unusual in several respects was installed at Balmat. The tank depth is 16 ft instead of the normal 8 ft. The rakes are raised and lowered by having the main drive gear located on a movable platform. Automatic controls are programmed to raise the drive platform and rakes during one shift of storage. During the next two shifts of withdrawal, the controls are programmed to lower the drive platform and rakes.

Jan 5, 1966

By M Thompson

"The Jaguar concentrator, 60 km north of Leonora, Western Australia (WA), consists of a standard closed circuit semi-autogenous grinding (SAG) and ball mill producing a float feed of approximately 60 micron at 70 t/h. Following comminution, separate copper and zinc concentrates are produced by differential flotation. These concentrates are subsequently dewatered by thickening and then filtration.Separate audits of the Jaguar Operation’s copper and zinc concentrate thickeners were conducted to evaluate their performance, following occasions where site personnel had identified unnecessary loss of copper and zinc concentrate to the thickener overflow. The feedwells were identified as the source of the observed problems due to the following issues with their design/duty:lack of retention time in the feedwell as current design is completely opennot conducive to effective mixing required for efficient flocculationdiameter of the zinc concentrate thickener feedwell was undersize for its duty.To improve the performance of the thickeners, it is planned to replace both concentrate thickener feedwells with a high rate design for their respective duties in February 2016. The audits also identified that the feed system requires modifications with particular importance placed on minimising air entrainment of slurry into the thickener feedwell. Minimisation of air entrainment is hoped to be achieved by providing constant head pressure through installation of weir arrangements in the feedboxes and redirecting each feed pipe so that it feeds tangentially into the feedwell. In addition, improvements to the control philosophy of both thickeners will be made with the installation of an ultrasonic bed level probe and bed mass sensor, in order to make real-time adjustments to the underflow pump speed to maintain steady state operation.Following the feedwell replacement and modifications to both thickeners it is expected that losses of recovered copper and zinc will decrease to undetectable levels. Subsequently it is anticipated that a more consistent, homogenous underflow can be produced for downstream filtration.Citation:Thompson, M, 2016. Concentrate Thickeners Feedwell Replacement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By G. M. Lee

SEVERAL improvements have been made in Granby smelting practice since the company abandoned the direct smelting of raw ore in the blast furnaces in June, 1927, in favor of sintered concentrate. These improvements have been made in several fields, but the most novel and outstanding change was the development of a process of concentrating most of the gold, and a somewhat smaller fraction of the silver present, in a small portion of the blister copper produced. The practice of making "copper bottoms" is usually associated with the reverberatory smelting of copper ores containing high percentages of impurities, or of copper matte high in precious metals. It has for its object, in the one case, the production of a major part of the copper relatively free from impurities and, in the other case, the production of a small per¬centage of the copper carrying the major part of the precious metals. Although the blister copper produced at the Anyox plant of the Granby company is remarkably free from deleterious impurities and normally contains no great amount of precious metals, certain economic considerations made it advisable to concentrate the existing precious metals into a relatively small percentage of the blister copper produced. The process devised took advantage of principles and reactions of the usual bottoms processes, but was carried out in the converters instead of in a reverberatory furnace.

Jan 1, 1935

By P. V. Brough, K. B. Gillaspie

DECISION to build a mill at the Bayard property was made in May 1942. Western-Knapp Engineering Co., of San Francisco, assisted by engineers of U. S. Smelting, handled the design and construction. Much of the milling equipment was moved from the Company's mill at Goldroad, Ariz. Wartime restrictions necessitated wood construction and paper sheathing except for structures adjacent to the Bullfrog shaft. Construction started in September 1942 and milling in March 1943. Bayard ores are processed in a single-ection mill. About half of the ore treated during the past year was hoisted through the Bullfrog shaft and the rest was trucked from other shafts. Coarse storage includes four bins, two of 120 tons each for Bullfrog ores and two of 85 to 120 tons each, served by a truck ramp. The low capacity figure refers to

Jan 1, 1948

By Walter E. Duncan

THE ores treated at the concentrating plant largely come from the blanket replacement deposits of the northeastern part of Hardin County, Illinois, and consist of complex mixtures of galena, sphalerite and fluorspar in a gangue of quartz, limestone and sandstone. The several minerals are so intimately intergrown that they are not liberated at the sizes usually treated by gravity concentration in the usual fluorspar plant. For this reason, an all-flotation method of concentration was developed in cooperation with the station of the U. S. Bureau of Mines at Rolla, Mo.1 This flotation separation made possible the commercial production of four concentrates: (I) lead concentrates, (2) zinc concentrates, (3) acid-grade fluorspar concentrates and (4) metallurgical-grade fluorspar concentrates.2,3 Although fluorspar had been floated in Canada in 1921 4 and a plant at Rosiclare had been floating fluorspar since March 1929, fluorspar flotation was given considerable impetus by the Mahoning developments, since some features of the separation were quickly adopted by other fluorspar companies. The Bureau of Mines5 reports that in the 10 years preceding 1938 only 50,552 tons of fluorspar flotation concentrates were produced in the United States. The rise from this almost nominal figure to 153,750 tons (largely acid grade) in one year (1944)6 is indicative of the activity in fluorspar flotation occasioned by the war. The industry thus proved to be in a position to expand and keep up reasonably well with the requirements imposed upon it by such developments as occurred in high octane aviation gasoline alkylation, in the use of Freon as a refrigerant and as carrier in the Aerosol "bug bomb," and in the atomic bomb project as well as in the expansion of other activities requiring hydrofluoric acid; such as, for example, the aluminum industry. Despite the fact that the greater portion of acid-grade fluorspar produced in the last few years went directly into war uses, the future of the acid-grade field still appears bright. As a result of the activity in fluorine chemistry during the war, it seems likely that in the relatively near future almost every phase of human endeavor will find some fluorine compound involved. The other three concentrates produced deserve some attention in these introductory remarks. The lead concentrates first produced contained both zinc and fluorspar but these did not interfere with their marketing. As will be pointed out later, the quality has steadily improved until today it is a relatively high-grade product. Although some zinc smelters accept concentrates containing limited quantities of fluorspar, it is a very objectionable impurity. Since flotation methods fail in the complete removal of the fluorspar, chemical methods were developed for

Jan 1, 1946

By Yaxiong Wang, Yong Li, Yuedong Wu, Haigang Dong, Jiachun Zhao

A roasting-leaching process has been developed for concentrating platinum group metals (PGM) from a PGM-containing ferroalloy. The optimized roasting conditions used a NaOH-to-ferroalloy mass ratio of 1.2 at 600 °C for 2 h. The roasted product mainly comprised Na4SiO4, NaFeO2 and Fe2O3. The iron oxide and sodium silicate associated with the roasted product were leached in water and dilute sulfuric acid solution, while the PGM was concentrated in the acid-leached residue. A PGM concentration of 23.4% was obtained with assaying, and the concentration factor of PGM from the ferroalloy to PGM concentration was greater than 9.

Jun 14, 2021

[ ]

Jan 1, 1938

By Read T. A

THE Broken Hill South Ltd. is one of ten companies operating on the Broken Hill lode (See Fig. 1). It has two leases-Blocks 7 and 8-of a total length of 2250 ft. on strike of lode.From the surface to 425-ft. level the ore was found principally in the form of carbonates and high-grade friable sulphides. Below the 425-ft. level the ore is found in the form of compact sulphides. The ore-bodies found in the South mine may be broadly divided into two classes...

Jan 1, 1921

By Rolf N. Schulz

The recently completed major modifications and additions to Reserve Mining Company's taconite concentrating process incorporate a totally new control system. Design of the new control scheme is centered on reliability, versatility, centralization, and optimization. The design objectives were achieved through a distributed control system based on a network of independent field located micro-processor based control systems connected to a central control room. Operation of each micro-processor can be interrogated and modified from the central control room by the operator or by either of two computer systems. The two computer systems handle logging, alarming, specialized sequenced controls, and complex process optimization routines.

Jan 1, 1980

By R. N. Schulz

The recently completed modifications and additions to Reserve Mining Company's taconite concentrating process incorporate a totally new control system. Design of the new control scheme is centered on reliability, versatility, centralization, and optimization. The design objectives were achieved through a distributed control system based on a network of independent field located microprocessor based control system connected to a central control room. Operation of each micro-processors can be interrogated and modified from the central control room by the operator or by either of two computer systems. The two computer systems handle logging, alarming, specialized sequenced controls, and complex process optimization routines.

Jan 1, 1984

By S. K. Mohanty, T. M. Dittrich, M. J. Allen, M. Dardona, A. C. Strzelecki, J. Hovey, Boukhalfa. H.

Rare earth elements (REEs) have many critical uses in advanced technology and the lack of a reliable domestic supply has been identified by the US DOE as a vulnerability to US economic security. Our research focuses on developing an economical process for extracting REEs from coal fly ash and power plant wastewater sludge by coupling a hydrothermal extraction process with the engineering of a ligand-associated media for concentrating REEs from the extraction liquid. Ash samples have been collected from two Detroit-area Power plants that burn 100% low sulfur coal (Trenton Channel) or fuel blends of 75% low sulfur coal and 25% high sulfur coal or 70% low sulfur coal, 15% high sulfur coal, and 15% petcoek (Monroe Power Plant). Ash samples are then subjected to hydrothermal conditions from 100-350 °C for 1-24 h at Los Alamos National Laboratory and leachate concentrations are measured by inductively coupled plasma-mass spectroscopy (ICP-MS) and compared to hydrofluoric acid digestion results. Experiments designed to aid in ligand selection and loading optimization show that di-(2-ethylhexyl)methanediphosphonic acid (H2DEH or DIPEX™) can be successfully loaded to a commercially available swellable organically modified silica (SOMS) media. Preliminary results show that DIPEX-associated SOMS surface loading can exceed 4x on a mass/mass basis and in simplified sorption experiments with Nd solutions (~pH 2), the DIPEX-SOMS media can sorb >90 mg Nd per g of media. Recovery of the sorbed Nd with low pH solutions has had low efficiency with the high (4 g DIPEX/ g dry media); however, near complete recovery was achieved with lower surface loadings (0.05 g DIPEX/ g dry media). Column experiments are being conducted to evaluate the optimal ligand/media ratio for repeated use. Completive sorption with Fe and other major cations are also being evaluated.

Jan 1, 2019

By B. W. Gandrud

WET-PROCESS coal-washing tables as we know them today have been in use in this country for approximately 25 years. The literature records only a few table installations worthy of note prior to adoption of the present-day differential-motion table. According to Phillips,' six Campbell bumping tables were being operated by the St. Bernard Coal Co., Earlington, Ky., in 11893. As late as 1923, according to Richardson, 2 72 such tables were in operation in the Rosedale washery of the Cambria Steel Co., at Johnstown, Pa. Bumping tables probably were not used to any considerable extent except in the plant at Earlington, and at two or three plants in Pennsylvania, but they may be considered as forerunners of the present-day coal-washing table. The transition from bumping tables to the type of tables now in use signalized a revolutionary change in table design. The advantages of the new design over the old were so outstanding as to make its adoption inevitable. BUMPING TABLES Bumping tables, as the name implies, utilized a bumping action for conveying the refuse and discharging it over the refuse end. The tables were hung from rods attached to overhead supporting beams. A shaft and cam arrangement at one end of the table served as the actuating mechanism and imparted to the table an endwise, back-and-forth, swinging motion. A bumping block was fixed in the proper position at the shaft end, so that the table would strike against it at the end of each backward swing. The hanger rods or stirrups were so adjusted as to give the table a slight uphill slope toward the refuse end; that is, the end next to the driving mechanism. The feed box was near the upper end, of the table and designed to spread the mixture of coal and water over the width of the table. Wash water was added a short distance below the feed box with the table in motion and coal mixed with water being fed to it through the feed box, a certain amount of stratification took place, depositing heavy refuse at the bottom of the bed in contact with the surface of the table. Constant bumping and a certain amount of

Jan 1, 1943

By B. W. Gandrud

WET-PROCESS coal-washing tables as we know them today have been in use in this country for approximately 25 years. The literature records only a few table installations worthy of note prior to adoption of the present-day differential-motion table. According to Phillips,' six Campbell bumping tables were being operated by the St. Bernard Coal Co., Earlington, Ky., in 1893. As late as 1923, according to Richardson, 72 such tables were in operation in the Rosedale washery of the Cambria Steel Co., at Johnstown, Pa. Bumping tables probably were not used to any considerable extent except in the plant at Earlington, and at two or three plants in Pennsylvania, but they may be considered as forerunners of the present-day coal-washing table. The transition from bumping tables to the type of tables now in use signalized a revolutionary change iii table design. The advantages of the new design over the old were so outstanding as to make its adoption inevitable. BUMPING TABLES Bumping tables, as the name implies, utilized a bumping action for conveying the refuse and discharging it over the refuse end. The tables were hung from rods attached to overhead supporting beams. A shaft and cam arrangement at one end of the table served as ,the actuating mechanism and imparted to the table an endwise, back-and-forth, swinging motion. A bumping block was fixed in the proper position at the shaft end, so that the table would strike against it at the end of each backward swing. The hanger rods or stirrups were so adjusted as to give the table a slight uphill slope toward the refuse end; that is, the end next to the driving mechanism. The feed box was near the upper end of the table and designed to spread the mixture of coal and water over the width of the table. Wash water was added a short distance below the feed box. With the table in motion and coal mixed with water being fed to it through the feed box, a certain amount of stratification took place, depositing heavy refuse at the bottom of the bed in contact with the surface of the table. Constant bumping and a certain amount of

Jan 1, 1943

By B. W. Gandrud

WET-PROCESS coal-washing tables as we know them today have been in use in this country for approximately 25 years. The literature records only a few table installations worthy of note prior to adoption of the present-day differential-motion table. According to Phillip,1 six Campbell bumping tables were being operated by the St. Bernard Coal Co., Earlington, Ky., in 1893. As late as 1923, according to Richardson, 2 such tables were in operation in the Rosedale washery of the Cambria Steel Co., at Johnstown, Pa. Bumping tables probably were not used to any considerable extent except in the plant at Earlington, and at two or three plants in Pennsylvania, but they may be considered as. forerunners of the present-day coal-washing table. The transition from bumping tables to the type of tables now in use signalized a revolutionary change in table design. The advantages of the new design over the old were so outstanding as to make its adoption inevitable. BUMPING TABLES Bumping tables, as the name implies, utilized a bumping action for conveying the refuse and discharging it over the refuse end. The tables were hung from rods attached to overhead supporting beams. A shaft and cam arrangement at one end of the table served as the actuating mechanism and imparted to the table an endwise, back-and-forth, swinging motion. A bumping block was fixed in the proper position at the shaft end, so that the table would strike against it at the end of each backward swing. The hanger rods or stirrups were so adjusted as to give the table a slight uphill slope toward the refuse end; that is, the end next to the driving mechanism. The feed box was near the upper end of the table and designed to spread the mixture of coal and water over the width of the table. Wash water was added a short distance below the feed box. With the table in motion and coal mixed kith water being fed to it through the feed box, a certain amount of stratification took place, depositing heavy refuse at the bottom of the bed in contact with the surface of the table. Constant bumping and a certain amount

Jan 1, 1950

By Charles H. Tiernon

Separation of particles on a table deck* results from differences in specific gravity, plus a number of other interrelated phenomena: size of particles; shape of particles; stratification (consolidation trickling); and hindered settling. The effective use of these factors may be controlled and aided by the following table adjustments: differential action of the drive or head motion; speed of motion; length of stroke; side tilt; end elevation; size of deck area; shape of deck; character of deck surface; riffle design; amount and distribution of wash water; feed water-to-solids ratio; feed rate; and feed uniformity. The typical concentrating table used in the US coal industry is essentially a rhombohedral-shaped deck supported by a suitable subframe. It generally slopes in the direction of the short axis, tilts upward at the refuse end of the long axis, and is differentially reciprocated in the direction of the long axis. This head motion tends to move the particles longitudinally toward the end of the table. At right angles to this movement, wash water (distributed along the high side of the table) tends to move particles down the slope parallel to the short axis of the table. Hence, the natural path of a particle on a concentrating table is from the feed box corner to the diagonally opposite corner of the deck (Fig. 1). There is a natural tendency for heavier particles to sink to the deck of the table and for lighter particles to stay nearer the surface. As a consequence, the heavier particles are carried further along the longitudinal axis since, being on or near the surface of the deck, they are more affected by the table's reciprocating action. The lighter particles, being at or near the top of the moving bed, travel slower in a longitudinal direction and thus separate from the heavy particles. Wash water and the diluting water in the feed cause lighter gravity particles to move down the short axis of the table. The feed material then fans out from the feed box, where it enters onto the table with heavy gravity particles moving in one direction and lighter particles moving in another. By properly adjusting all of the previously mentioned factors, a clear-cut separation is possible between high- and low-gravity particles, or between refuse and coal. Riffles are of great importance to tabling. They create considerably more capacity than is possible with smooth decks, and they are responsible for better separation accuracy. Particles in their downward movement along the deck's slope are delayed behind the riffles. Hindered settling, consolidation trickling, and other phenomena occur as the particles tumble over the riffles and stratification ensues. The heavier particles settle to the deck of the table and are trapped behind the riffles, thus insuring their positive movement toward the end of the table. Since stratification and separation of particles are not complete as a result of any one riffle, a series of riffles are used. The cycle of stratification and hindered settling is repeated from riffle to riffle. The result is purer products as particles fan out and progress forward and downward over the table. The smallest, heaviest particles stratify downward to the surface of the deck more quickly and are carried out by table movement toward the refuse end at a faster rate than coarse, heavy particles. Light gravity, larger pieces ride on the top layer of particles and flow down the deck's slope as a result of the cross flow of wash water at right

Jan 8, 1980

MINING, to be precise, ends when the ore is delivered to a bin outside the mine. Usually the next step is concentrating; or, as it is more often called, milling. A few elementary definitions will help make clear the discussion that is to follow. A rock is an aggregate of minerals; copper ore is rock that contains copper-bearing minerals in quantity sufficient to make it profitable to mine and recover the copper in the form of marketable metal. Manifestly, under a literal interpretation, a mass of material might be copper ore one day and merely copper-bearing waste rock a week later, if the price of copper happened to drop in the interim. Emphasis already has been placed on the expansion that took place in the ore reserves of the Porphyry companies as a consequence of the great strides made in the technique of mining and ore treatment. So, even if one inserted a qualifying phrase, "at an average price for the metal," after the word "profitable," the definition would still be open to criticism. Place is another factor. It is evident that a body of excellent ore in Arizona might cease to be ore in the economic sense if it were moved intact to the interior of China. However, it is with ore in its technical and scientific aspect that this chapter is concerned. Speaking in general terms, the ton of Porphyry ore as it arrives at the surface contains 25 to 70 lb. of copper minerals in the form of disseminated particles or thin coats along fracture planes. When subjected to appropriate treatment this ton yields 12 to 40 lb. of metallic copper. These ranges take into account conditions of today and of 25 years ago. Two procedures are available: (1) concentration, followed by smelting of the concentrate, or (2) leaching and precipitation, usually by electrolytic deposition. Smelting and leaching are metallurgic processes in that they involve chemical change; concentration

Jan 1, 1933

By E. H. Crabtree, Neil S. Parker

The custom milling plant of the Eagle-Picher Mining and Smelting Co. is at Sahuarita, Arizona, approximately 20 miles south of Tucson. It is connected by a 2-mile railroad spur to the main line of the Southern Pacific Railroad between Tucson and Nogales. The capacity of the plant is 500 tons per day. The mill is conventional except perhaps in the rather wide variety of ores treated. These vary from straight copper ores, from which only one concentrate is produced, and lead-zinc or copper-zinc ores from which two concentrates are produced, to complex gold-silver-copper-lead-zinc ores, which require the simultaneous production of three or lour concentrates. Custom ores are received in lots varying in size from a few truckloads to several carloads. Similar ores, after crushing and sampling, may be commingled, or individual lots may be milled individually. The ores are first dumped either into one of two 200-ton railroad bins, or into one of the two 75-ton truck bins. From these bins the lot of ore is individually crushed in a 24 by 16-in. jaw crusher to 3-in. size, and then to ½-in. size in a 3-ft Symons shorthead crusher. After crushing to ½-in., the ore is conveyed to the automatic sampling plant. This consists of three Vezin samplers in series, each successively cutting out 10 pct, 10 pct and 5 pct of its feed. After No. I sampler, the material passes through a mixing barrel and is then crushed to -in. in a set of rolls before passing to No. 2 sampler. Between No. 2 and No. 3 samplers, the ore is again mixed in a mixing barrel. The final sample, consisting of one pound per ton of ore, is taken to the laboratory, where it is further crushed to 1/8-in. in a coffeemill, and then riffled down to the size required for grinding in a pulverizer. The capacity of the crushing and sampling plant is up to 100 tons per hour, depending upon the character of the ore. After sampling, the ore is stored in five ore-storage bins, consisting of four 200-ton bins and one 175-ton bin. Each of these bins is discharged by means of belt feeders and conveyor to the ball mills, so that ores may be composited for milling in any required ratio, or milled separately by themselves. Fine grinding is done in one 6 by 4-ft Allis-Chalmers ball mill and one 8-ft by 36-in. Hardinge mill. These two mills both discharge to one 54-in. Akins Simplex High weir classifier. The classifier sands can be returned to either or both mills, so that flexibility in grinding for different ores is easily obtained. Flotation equipment consists of four 66-in. Fagergren machines for copper-lead roughing and six similar machines for zinc roughing. Lead-copper bulk concentrate is cleaned and recleaned in eight No. 18-S Denver machines, and zinc concentrate is cleaned in three 66-in. Fager-grens. Copper-lead differential separation

Jan 1, 1949

By R. A. Pallanch

Probably one of the most perplexing problems with which a mill operator contends is the proper evaluation of his mill results. True, he accurately determines his recoveries of metals and grades of products monthly, weekly, and often daily. These figures do not of themselves directly translate to mill economics. When one figure is unusually good there may be an offsetting circumstance. The advantage of high lead or zinc concentrate grade may be offset by poorer recovery; high lead recovery may be offset by poorer zinc recovery, or vice versa; and so on. Besides, grades or recoveries may not of themselves mean more than a reflection of the grade and character of the ore during the period under study. What the operator sorely needs is some one measuring stick that tells him when he has achieved his greatest return, regardless of grades or recoveries—for if he knows his methods and practices are yielding the optimum return he need no longer concern himself with the assays of products and tailings, or the corresponding distribution of metal values. At first blush it would appear that the obvious answer to this is the actual money return to the mill. Paradoxical as it may seem, however, money return does not make a dependable yardstick any more than do grades and recoveries, as ore condi- tions would vary enough to bring about greater money return during periods when the actual metallurgical work is not as good. The mill operator, of course, should always aim for the greatest return on the ore, once it is in the mill bins, with proper attention always to mill treatment cost. The need of a proper yardstick becomes more imperative with the increasing complexity of the problem. In the case of a simple, single-product operation on a fairly uniform ore, in which only one metal is of significant importance, the need is not great, as grade and recovery pretty well tell their own story. At the other extreme is the operation that makes three or four separate marketable products from a complex mixture of heterogeneous ores that vary tremendously in individual metal contents and ratios, degree of oxidation, and other characteristics, and in which gold, silver, copper, lead and zinc are all significant values. Economic Recovery The first attempt at obtaining a proper single yardstick for a fairly complex ore with which I am familiar is the use of the ''Economic Recovery" term at the lead-zinc flotation mill of the Sunnyside Mining and Milling Co., Eureka, Colorado. This method had been applied there early in Sunnyside flotation-mill history (not later than 1920) and credit for the innovation I believe belongs to Messrs. Kuryla and Marquand. The term "Economic Re-

Jan 1, 1949

By Foster Fraas

That variations in the humidity of the air and in the moisture content of a mixture of broken solids being separated electrostatically cause trouble is not new.' Much of the reputation for unreliability commonly ascribed to the electrostatic separation processes is probably due to this one factor alone. Some operators dry thoroughly before separating; and while this is good in many instances, there are others in which it is not the remedy for trouble. Some mixtures behave best in very dry air and with the mixtures fed to the separator while hot to reduce the adsorbed water content. On the other hand, an overdried mixture on coming to equilibrium with more humid air, has been known to take up moisture selectively on one family of particles, as of coal in the presence of slate and clay, and give sharper electrostatic separation. From these observations it is concluded that there is a permissible moisture content for a particle and also for the atmosphere surrounding it, if in equilibrium, at which the particle will have a conductivity or cntact potential2-4 that is ideal for electrostatic separation. This permissible moisture content varies between a wide range of limits for the different materials that are are and with the kind of electrostatic separating process used. Water can be present as a result of adsorption and condensation from the atmosphere, as an accumulation before or during mining, or as a residue from a previous process step. The water may exist as a liquid film or as an adsorbed layer of vapor. If the water exceeds permissible limits it must be removed. Its state determines the method. Drying by evaporation is necessary for adsorbed water, for part of the liquid-film water (that is, up to several percent of the dry weight), and for free water in the internal structure. Large water contents may be removed by drainage Or filtration. At just what point mechanical removal should cease and drying by evaporation begin depends upon the method of mechanical removal and its cost. Particles can also be separated according to their differences in dielectric constant when suspended in a liquid of intermediate dielectric constant. Recovery of this liquid presents a a problem' Permissible Moisture The adsorbed moisture on the outer surface of minerals can be quickly removed or replaced. Accordingly, in speaking of adsorbed moisture contents, either that of the solid or that of the surrounding air may be considered, the two values being connected by a distribution coefficient which varies with the temperature. However, such a condition does not necessarily exist in processes where an initially dry material is suddenly introduced into an atmosphere having a partial pressure of water vapor or where a moist material is suddenly introduced into a dry atmosphere. Here the resultant differences in the

Jan 1, 1949