Search Documents

By R. Harris, M. Misra

Column flotation technology has a demonstrated potential for recovering clean coal from high-ash waste fines. The effect of different variables such as air flow rate, frother addition, depressant addition, percent solids and particle size on the quality of separation are discussed. Results indicate that air flow rate and depressant addition are the important variables which control the selectivity in the flotation of fine coal in a column cell. Separation efficiency achieved with column cells is significantly better than that with conventional flotation cells. Under appropriate experimental conditions with a deep column, more than 80 percent coal can be recovered in the concentrate containing 10 percent ash from waste fines containing over 60 percent ash.

Jan 1, 1988

By Felicia F. Peng

Two modes of collector addition techniques are applied in the column flotation for cleaning ultra fine coal. The collector can be: 1) added directly into the coal slurry through the feed system; and 2) gasified collector and transported in the gas phase through the bubbles. Operating parameters of the column flotation were investigated through three phases of work plans for Pittsburgh No.8 seam coal. In present study, the column flotation using two modes of collector addition techniques were tested and compared. Ninety percent or higher combustible recovery can be achieved by using both methods. However, utilizing the gasified collector addition technique in column flotation has more potential than direct liquid addition technique to obtain the higher recovery at same collector dosage.

Jan 1, 1993

By R. Sharma, S. Svoronos, S. Gupta, N. A. Abdel-Khalek

This paper presents the results of a column flotation study on a fine feed sample of Florida phosphate. A central composite design was used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to produce a high-grade concentrate with a high recovery. A 15ppm concentration of nonionic frother was found sufficient to maximize the recovery at pH of 9.5.

Jan 1, 2002

By R. Sharma, S. Svoronos, S. Gupta, N. A. Abdel-Khalek

This paper presents the results of column flotation of a fine feed sample of Florida phosphate. A central composite design is used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to achieve a concentrate of high grade and recovery. A concentration of 15 ppm of non-ionic frother is found to be enough to maximize the recovery at the pH of 9.5.

Jan 1, 1999

This paper presents the results of column flotation of a fine feed sample of Florida phosphate. A central composite design is used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to achieve a concentrate of high grade and recovery. A concentration of 15 ppm of non-ionic frother is found to be enough to maximize the recovery at the pH of 9.5.

Jan 1, 1999

By G. A. Kosick, M. Freberg, L. A. Kuehn

"Highly variable and higher than forecast lead miff feed grades were problems experienced at the Polaris Concentrator. Limited flotation capacity and poor operating flexibility prevented the plant operators from overcoming these difficulties, and resulted in grades and recoveries which were lower than necessary.Two column cells were integrated into the lead circuit in an effort to give the operators the tools they required to achieve the best grades and recoveries possible, regardless of the miff feed grade. Installation of the column cells increased lead concentrate grade from 76% to 79.3% Pb, and increased lead recovery from 9/% to 91.3% Pb.This paper reviews the design, development and operation of column flotation cells in the lead circuit at the Polaris Mine.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec, and towed to its pre sent location on Little Cornwallis Island, Northwest Territories, about 1450 km from the North Pole. The plant presently treat s about 2800 mtpd of new feed with average feed grades of 3010 Pb, 13% Zn and 5% Fe. Current production averages 36 000 tonnes of lead concentrate and 220 000 tonnes of zinc concentrate annually.The barge design and min e location dictated that the concentrator .be compact with very little unused floor space. As a result, flexibility was limited in terms of expanding the plant.Mill feed grades were highly variable and above forecast and the lead flotation circuit was found to be under capacity. This caused continued overloads in the lead cleaning circuit, resulting in low concentrate grades and recoveries. It was evident that an increase in lead flotation capacity and flexibility was necessary. The existing floor space did not allow for the installation of additional conventional flotation cells, but one alternative was the installation of column cells."

Jan 1, 1988

By Schommarz KH, Dunne RC, Goodall CM

Column cells are widely used today for the recovery of base metals by flotation. Their use for the flotation of iron sulphides has not been as rapid. Australia has pioneered the use of large rougher flotation columns. During the last six years, seven rougher columns have been installed on gold mines treating iron sulphides and the technical viability of this technology has been demonstrated. Laboratory column testwork on a gold bearing iron sulphide ore demonstrated the effects of both physical and chemical parameters. In general the large commercial columns operate over a broad range of conditions depending on the downstream treatment of the flotation concentrate. The addition of wash water to commercial columns is not universally applied and there appears to be a need for a better wash water System.

Jan 1, 1993

By H Thanasekaran, L Christodoulou, J Kohmuench

"Column flotation has been successfully applied to iron ore concentration since the 1980s with the goal of reducing silica content and allowing for the efficient production of pellet feed. Since then, columns have been widely used in iron ore processing due to: their lower capital and operational costs when compared to conventional cells their ability to generate higher concentrate grades and recoveries.Currently, more than 100 columns have been installed within Brazilian iron ore processing circuits for rougher, cleaner and scavenger duties. Despite it being a well-established approach, several technological advances have improved column design, accessories and performance. This work presents the performance of some iron ore columns in Brazil and the recent technological developments.CITATION:Thanasekaran, H, Kohmuench, J and Christodoulou, L, 2013. Column flotation of iron ore - status and advances, in Proceedings Iron Ore 2013, pp 479-484 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By J. L. Huiatt, D. G. Foot, J. D. McKay

The US Bureau of Mines compared column flotation using either fine or coarse bubbles with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a &.7% Cr2O3-grade rougher concentrate with 87% recovery, compared with 43.8% and 43.5% Cr2O3-grade rougher concentrates with 85% and 77% recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse- and fine-bubble column flotation produced rougher concentrates containing approximately 41.5% Cr2O3 with 95% recovery, exceeding conventional flotation, which produced 35.6% Cr2O3 -grade concentrates with 87% recovery.

Jan 1, 1987

By J. D. McKay

The Bureau of Mines devised a column flotation technique using either fine or coarse bubbles and compared it with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a 44.7-pct-Cr203-grade rougher concentrate with 87-pct recovery, compared with 43.8- and 43.5-pct-Cr203-grade rougher concentrates with 85- and 77-pct recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse-and fine-bubble column flotation produced rougher concentrates containing approximately 41.5-pct-Cr203 with 95-pct recovery, exceeding conventional flotation which produced 35.6-pct-Cr203-grade concentrates with 87-pct recovery.

Jan 1, 1985

By D. P. Patil, T. C. Rao, J. P. Barnwal

Factorial design of column flotation experiments was used to understand the main and interactional effects of the column parameters. In the experiments, the air flog rate, the wash-water, flow rate and the froth depth were varied at two levels. Analysis of the results showed that an increase in airflow rate had a deleterious effect on the grade of the concentrate, whereas, an increase in froth height increased the grade. The interactions between airflow and wash water and between airflow and froth height were significant with respect to grade of the concentrate. These results demonstrated that, from an ore containing 12.76% P2O5, it is possible in a single-stage flotation column to obtain a concentrate containing 31 % P2O5 (10.6% Si02) with a recovery of 94%, thus reducing the number of cleaning stages that would be required if conventional flotation cells were used.

Jan 1, 1997

By C. N. Bensley, S. K. Nicol, R. Lamb, G. W. Kidd

Flotation circuits in the metalliferous industry recover high value concentrates from very fine (minus 0.lmm), low grade, slow-floating feeds. Flotation columns acting as final cleaners within these circuits offer the benefits of higher grade concentrates, reduced circuit complexity, improved control and reduced power consumption. By contrast, in the coal industry, these benefits have not been realised, principally because columns are not well suited to the treatment of conventional coal flotation feeds (minus 0.5m). However, this does not imply that columns do not have a place within the coal industry, rather that they must be applied in a role where all the unique advantages of column flotation can be of benefit. The development of a commercial scale column to recover discarded ultrafines from the Riverside preparation plant of BHP-Utah Coal Limited is discussed. Particular emphasis is placed on the column design features pertinent to the recovery of ultrafine coal. Pilot and commercial scale column performances are compared. The results of the commercial scale testwork indicate that a full installation at the 5.5 MTPA Riverside plant would annually recover additional coal worth $US 6.6M.

Jan 1, 1988

By Samuel Polinsky, Lawrence W. Bierman, Wayne Perkins

[A column float beneficiation plant using 9, 8.5 foot diameter, cells was constructed by the Simplot Company and the Smoky Canyon Facility in the fall of 1986 and has been in operation since May of 1987. The float beneficiation process was developed jointly by the Simplot Company and the Bureau of Mines (Salt Lake City, Utah) which incorporates the Bureau's bubble generator design and chemistry system based around the reverse float technology, (Albany Bureau of Mines, Application of Carbonate-Silica Flotation Techniques to Western Phosphate Materials, Rule, Dallenbach , Larsen, RI8728, 1982) . This chemistry has been modified by Simplot in both patented and unpatented improvements. The objective of the beneficiation process was to reducethe A1203 content in the overall pipeline concentrate by 0.2 wt z. Therefore, a process stream was identified in the mill circuit which provided an opportunity to isolate and treat 1100 tons per day of poor quality phosphate concentrates The process allows recovery of approximately 15% of the mill concentrates, otherwise unsuitable for fertilizer production. The alternative would have been to waste this ore. Wasting would have resulted in considerable ore loss, increased mining costs and required additional products grinding. ]

Jan 1, 1989

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981

By D. G. Foot, J. D. McKay, R. A. Ynchausti

The increasing popularity of column flotation as an efficient and profitable mineral beneficiation technique has resulted in the need to perform a study of basic column operating parameters in order to understand mineral behavior in a column. Variation of column rougher flotation parameters on the Nevada Fish Creek fluorite and Utah Collins manganese ores enabled characterization of four beneficiation zones within a column flotation cell. Although specific mineral behavior in each zone was peculiar to the mineral system involved, particle retention time predominantly affected both manganese and fluorite recoveries in the collection zones of the column while enhancing mineral grades in the cleaning zones. Column parameters such as column length, feed injection location, and tailings recirculation velocity were inherently linked to particle retention time and retention time distribution, both of which affected mineral recovery. Froth depth had a discernible effect on fluorite concentrate grades; as froth depth increased, fluorite grades increased. Wash water additions affected both fluorite and manganese recoveries and fluorite grade. Axial mixing drastically reduced fluorite and manganese recoveries due to short circuiting of some of the feed slurry in the column.

Jan 1, 1988

By J. G. Groppo, B. K. Parekh

Eastern US oil shale contains approximately 10 to 12 gallons of oil per ton and 7 to 10% pyritic sulfur. Physical beneficiation of these low grade shales using froth flotation provides a high grade material that makes extraction of oil more economically attractive. The Alabama oil shale used in the present study contained 16.46% organic carbon and 14.5 gallons of oil per ton as determined by Fischer assay. Liberation size of the kerogen was estimated at 10 µm. `Ken-Flote' column flotation technology provided a high grade concentrate containing as much as 60% organic carbon. However, carbon recovery was about 60%. Carbon recovery was improved to 75-85% while maintaining concentrate grades in excess of 40% carbon by providing longer retention time in the column, which facilitated effective bubble-particle collision and attachment.

Jan 1, 1994

By J. G. Groppo

Eastern U.S. oil shale contains approximately 10 to 12 gallons of oil per ton and 7 to 10 percent pyritic sulfur. Physical beneficiation of these low grade shales using froth flotation provides a high grade material which will make extraction of oil more economically attractive. The Alabama oil shale used in the present study contained 16.46 percent organic carbon and 14.5 gallons of oil per ton as determined by Fischer assay. Liberation size of the kerogen was estimated at 10 /-Lm. 'Ken-Flote' column flotation technology provided a high grade concentrate containing as much as 60 percent organic carbon, however, carbon recovery was about 60 percent. Carbon recovery was improved to 75-85 percent while maintaining concentrate grades in excess of 40 percent carbon by providing longer retention time in the column which facilitated effective bubble-particle collision and attachment.

Jan 1, 1993

By Gerald H. Luttrell, Roe-Hoan Yoon

Flotation columns are becoming increasingly popular due to their ability to improve selectivity and to reduce operating costs. Unfortunately, these advantages are not often realized because of poor operating practices and difficulties associated with design and maintenance. This article provides guidelines for the operation and design of columns. The discussion will focus on designing proper wash water systems for improved selectivity, maximizing throughput by increasing the bubble surface area rate, and minimizing operating and maintenance costs. It is suggested that the design of the air sparging system is the most critical element in column flotation.

Jan 1, 1993

By Dunne R. C

Column flotation is receiving increased interest from both an industrial and research perspective in Australia. The traditional overseas application as a molybdenum cleaning cell is being expanded and a number of new applications as cleaners, scavengers and roughers are emerging in Australia. The success of column flotation has hinged on the new understanding developing from the work of Finch- and coworkers at McGill University, Canada, particularly in relation to scale-up parameters and model development. The aspiring column flotation user in Australia now a has wealth of experience to draw on when deciding on the correct procedure to follow during the process evaluation and plant installation stages of development. However, some aspects relating to column design, such as aeration mechanisms, require careful evaluation.

Jan 1, 1987

By J. E. Gebhardt, H. Toro, K. Y. Lee

Industrial-scale test results indicate superior metallurgical performance of column flotation compared to conventional cell flotation for copper cleaning. A technical comparison of bubble generation systems for column flotation is made. Two types of bubble generation systems are considered: the filter-cloth type spargers and the Turbo-Air® sparger, which utilizes an air-water mixture fed to the column through injection tubes. Examples of the improved technical performance available with an external sparger system are presented using data from plant tests conducted for specific applications with several different mineral ores. INTRODUCTION Column flotation is now a valuable unit operation which mineral processing engineers employ in the design and operation of flotation circuits in nearly all mineral applications. The acceptance of columns in the mid- 1980s by the minerals industry was paralleled by a rigorous approach to developing a scientific understanding of the design, scale- up, and operation of column flotation units (Finch and Dobby, 1990). Since then, column flotation has become a standard unit of the cleaning stage in many new mineral concentrator projects and has replaced older mechanical cells to improve process efficiency. The size of column cells has continued to grow from the initial 0.9- to 2.1 -meter diameter range, and it is not uncommon to find column cells today being 2.7- to 3.6-meters in diameter. With the success of the smaller units, the scale-up to larger cells has been proven and demonstrated by the performance of the large-diameter cells (Murdock and Wyslouzil. 1991). The use of columns in flotation circuits has also been accompanied by developments in modelling. control, and optimization of column performance (Lee et al, 1991). The bubble generation system is the heart of the operation of column flotation cells. The most common methods for generating bubbles can be divided into two types: the internal and external spargers. Internal spargers are typically a porous material, such as sintered glass, porous rubber or filter-cloth, or maybe a single- or multi-nozzle sparger. External spargers implies that a gas and a liquid (either water or slurry) are brought into contact outside the column and that mixture is then introduced into the column. Several types of external spargers are available today, and innovative designs for externally mounted air sparging systems have been a significant factor in the successful application of columns. Early types of bubble generation systems.

Jan 1, 1993