Search Documents

By D. D. Harbuck

The U.S. Bureau of Mines recently identified a significant new source of scandium in an Oklahoma tantalum waste residue (approximately 0.24 pct Sc). Because scandium is a strategic and critical metal which the Department of Defense has classified for special consideration, the Bureau is researching methods of recovering scandium and associated metals from this and other process residues. A variety of operating parameters were evaluated to determine the best technique for recovering scandium. Testing showed that by sulfating the residue at temperatures as low as 150' C for reaction times as short as 0.5 hr, over 94 pct of the scandium converted to a water soluble form. Solvent extraction using DEHPA selectively recovered 100 pct of the scandium from the water leach solution.

Jan 1, 1992

The paper concerns an unconventional, yet promising, use of waste magnesite dust and fines. In India a significant amount of this dust is generated from some of the integrated iron and steel industries, refractory and cement plants, during calcination of raw magnesite. However. it is possible to utilize this dust, which is normally a waste, conveniently and economically for the production of magnesium. chemicals. A bench scale study was carried out to determine the rate of formation of sulfated com¬pounds of Mg.Ca,and Fe, inter alla, present in the dust system containing MeO constituents (in which Me=Mg.Ca,Fe,Si,Al etc.) Effects of various process parameters, which affect the reaction rate as also the purity of the product ,were also studied. Some work carried out to develop the process flow charts involving the salient steps to produce magnesium chemicals commercially is reported in the paper .

Jan 1, 1992

By S. Vukcocic

A long term research project is in progress to establish the parameters of an acid leach process to recover alumina 'froui' high-iron and/or low-iron white bauxites, kaolinite, coal. ash and copper mine tailing. In this paper the results of acid leaching of copper flotation tailing for the removal of alumina are presented. The tailing is very complex material which contains 25% Al203 in the -10 lim fraction. X-ray diffraction indicates presence of quartz, kaolinite and minor 'alunite. After classification and ,separation of the -10 lim fraction, the raw material is fired to 550GC and leached at 90GC. Filtration is applied for the separation of white silicate residue form leach liquid. After the purification step, aluminum salt is crystallized from the solution, and calcined to alumina. Kinetic correlation and regime, of the processes are defined and presented in the paper.

Jan 1, 1992

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non-ferrous metallurgical industry is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to ta,ke place at 'high temperatures and are now rapidly becoming accepted In many industries. This paper reviews experiences with a proprietary low density ceramic filter element. CerafH. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By Pragna N. H. Bhakta

The minerals industry is under political and economic pressure to reduce its processing wastes and minimize their impact on the environment: Recycling is one of the means by which the minerals Industry can reduce the quantities of effluents and residues that are discharged to the environment. The wise use of available resources is not only an environmental necessity but also an economic benefit as natural mineral resources are depleted and/or become more complex. The purpose of this paper is to review the technical and regulatory issues that will help shape the future of minerals recycling over the next ten years. Research and development to address technical issues will be discussed with emphasis on the Bureau of Mines recycling research program.

Jan 1, 1992

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to smelter smelting plants. In both primary smelting and converting, gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By Dai Yongnian

The methods of treating zinc crust and its development in the last hundred years are compared and reviewed. There are better effects from normal pressure metallurgy turned into vacuum metallurgy. The traditional methods dezinc only. But we must consider that delead on further step. From lab tests to industrial scale experiment are researched. The first step-dezinc, second-delead, crude ,metal of, zinc, lead and silver are produced, The flowsheet of treating zinc crust are simplified, material consumption reduced, work condition improved, environment protect mended. This method is pointed out that its application can be expanded.

Jan 1, 1992

By Roland Kammel

In combination with various physical and chemical methods also electrochemical techniques are most frequently used to improve the recovery of metals from aqueous dilute process streams or effluents e.g. in electroplating, metal finishing, mining and metallurgical plants. To insure cathodic metal recoveries with favorable current efficiency and high throughputs per unit of cell volume seve¬ral types of electrolysis cells have been developed comprising extended electrode surface areas and/or intensive electrolyte. agitation. The practical experiences with these units indicate especially for the electrolytic recovery of metals whose values are high, that the treatment cost permits profitable operations with relativly short payback periods for the units. Anodic reactions can be utilized for the removal of undesired anion contents or buildups of impurities. Appropriate combinations of these recovery methods are used to improve the versatility and the overall economy. Industrial applications reveal their potentional as addidtive techniques for existing processes to reduce the metal content of effluents to values that meet the guide lines of environmental legislation whereas integrated in-operation recovery methods are nowadays increasingly introduced to approach nearly close-loop operations.

Jan 1, 1992

By Rune Gammelsmter

Turbulent chemically reacting flows are generally very complex, involving interactions of chemical, thermodynamic, and fluid mechanical processes. A combustion model based oh algebraic moment closure has been developed. The model is applicable for reaction rates where the chemical kinetics can vary from slow to fast. The effects of turbulence is taken into account by means of modifications to the well known k-e modelling procedure. The model is applied to an industrial combustion process. Calculation of furnace off-gas combustion from an aluminum reduction cell has been performed. The theoretical results agree well with experimental values.

Jan 1, 1992

A study was undertaken to remove the Se from waste solutions using a raw form of the biomass called Iota Chips derived from the seaweed, Eucheuma spinosum. Removal of Se from solutions was investigated as a function of time, pH, conc. of Se in solution (0.1 to 100 ppm) and lota Chips to liquid ratios of 10-2 to 10-5. For solutions containing initial conc. of 0.1 ppm Se, with the addition of Iota Chips at a solid to liquid ratio of 10-3, the Se conc. decreased to 0.03 ppm in about 3 hours. Iota Chips absorption capacity to the Se and its application to the treatment of the metallurgical processing effluents are discussed.

Jan 1, 1992

By H. Y. Cheng

A pulse column solvent extraction system was evaluated as an alternative to mixer-settlers for the separation and purification of rare earths. The column tested had an inside diameter of 44.5 mm and had 36 sieve plates with a free area of 25%. Pulsing was provided pneumatically using a solenoid valve controlled by a timer so that both pulse amplitude and frequency could be varied. Feed to the column was a mixed rare earth chloride solution containing 10 g RE L-1. The extractant was 5% Ionquest® 801 in Shellsol 2037 diluent. Hydraulic performance of the pulse column was excellent with no propensity towards stable emulsions or crud formation under normal operating conditions. The column was operated in organic-continuous mode with flow rates chosen so that yttrium and the heavy rare earths were extracted with high efficiency while the light rare earths were rejected. Yttrium extraction varied from 83 to 99.2%. Concentration profiles were measured in both the aqueous and organic phases, and, from this data, the height of a transfer unit (HTU), the mass transfer coefficient (Kxa) and the continuous-phase axial dispersion coefficient (Ey) were computed. The HTU ranged from 17-92 an which is within the range of values reported for other (non rare earth) pulse column systems.

Jan 1, 1992

By Richard S. Kunter

Artech Recovery Systems, Inc has developed a low pressure and temperature? leach process called the "Cashman Process" to extract metals from arsenical flue dusts and residues and fix the arsenic in an environmentally stable form as ferric arsenate (scorodite). The process was pilot tested at Hazen Research in an integrated plant including continuous recycle from August 1989 to October 1989 during which several tons of flue dust were processed. Based on this pilot program, the process was deemed technically feasible and produced commercially salable products. Residues from this pilot program were subjected to a long-term stability test jointly designed by PTI environmental services and the USEPA. The process, its versatility, and the nature of the products is discussed in some detail.

Jan 1, 1992

By Georges J. Kipouros

Anhydrous neodymium trichlorids (NdCl3), containing ~1 weight percent neodymium oxychloride (NdOCI) was prepared by the dehydration of neodymium trichioride hexahydrate (NdC13.6H2O). Dehydration of the hexahydrate was conducted in three steps. First, the hexahydrate was slowly heated in air to about 250 °C until all the low temperature water of crystallization was removed. In the second stop, the neodymium hydroxychloride (Nd(OH)2C1) fanned in the first step was decomposed by heating under argon to 430 ° C. Finally the salt was ground and then treated with HCl gas at 330 °C until practically all of the NdOCl was converted to NdCl3.

Jan 1, 1992

By J. M. Tourre

Recently, interest in rare earth based oxide powders for electronic applications has risen dramatically. Considerable research has been devoted to the chemical synthesis of these compounds to improve the control of physical and chemical characteristics of the powder. In most cases, a high degree of homogeneity, purity and reproducibility is necessary in order to obtain good application properties. The synthesis parameters can control particle size, surface area, and morphology as well as the degree of homogeneity and application properties. Rhone-Poulenc, a world leader in the production of separated Rare Earth chemicals has developed a flexible process to produce a wide variety of compounds. The different processes for the synthesis of YBa 2Cu 3 O 7 will be discussed and compared to the RP process in term of product quality, cost and flexibility.

Jan 1, 1992

By G. Archer

ASARCO, a large and diverse producer of nonferrous metals, is involved primarily in the smelting and refining of lead and copper. Lead-antimony alloys, antimony trioxide, bismuth, cadmium oxide, selenium, tellurium, silver and gold are among products which result from processing by-products of smelting and refining. The complex mixture of concentrates at some smelters and the high impurity loads at some refineries result in various drosses, sludges, dusts and slags. In this paper, the complex interplant and intraplant transfer of by-products is addressed. These by-products result in an exchange of metals between the lead circuit and the copper circuit. Examples of the transfer of by-products and the prospects for the recycle of valuable products from wastes generated by customers and unrelated processors are also discussed.

Jan 1, 1992

By T. J. A. Smith

This paper provides an overview of some of the key issues in design of smelter gas handling systems, with particular reference to sulphide smelting plants. In both primary smelting and converting. gas handling and treatment systems often represent the major capital cost component. There is also ample evidence that poor system design can be a major cause of smelter down time, lost production and unforeseen high maintenance costs. The paper discusses these issues and offers guidance for improved design.

Jan 1, 1992

By Kenneth L. Driggs

The Environmental Protection Agency's Clean Air Act of .1970 provided the driving force for the current Magma Smelter configuration. The historical and technical perspectives of those process developments are reviewed. Innovations in procedures and equipment have allowed compliance with the requirements of the regulating authorities. The wet scrubbing of converter gasses and the monitoring of converter operations by a controlling foreman are two of the major contributors to these successes. The Clean Air Act Amendments of 1990 have posed many new concerns for all U.S. industry, including the few (seven) primary copper smelters remaining. Future concerns include tightening the sulfur dioxide ambient standard from the current three-hour averaging period to one hour"

Jan 1, 1992

By Larry B. Fiske

Elimination of dust and processing of fines for both thermal and metallurgical coals is addressed. The efficiency of treatment with lignosulfonates compares favorably to oil in thermal coal. Effect of treatment with various lignosulfonates upon cokability of metallurgical coal was determined by Free Swelling Index, Gieseler Plasticity and Arnu Dilatation.

Jan 1, 1992

By Musa Karakus

Reflected light microscopic (RLM) examination of dust particles from lead and copper smelters can effectively characterize their mineralogy, texture, and origin. Scanning electron microscopic-energy dispersive spectroscopic (SEM-EDS) analysis provides confirmation of the optical identifications and chemical data on the phases. Studied lead smelter dust samples were from the: I) blast furnace, 2) sinter plant scrubber, 3) sinter plant crusher, 4) dross furnace, and 5) refinery. Phases identified included galena fragments, melted PbS, metallic Pb and Cu, Cu-Ni, Cu-Zn, Zn-Ag, Zn-Cu-Ag, Ni-Cu-Sb, and Ni-Cu-Zn-Ag metal alloys, Ni-sulfide, Cu-sulfide, and Cu-Pb-sulfide dross .phases; slag and sinter particles, coke fragments, unreacted original feed phases: pyrite, chalcopyrite, sphalerite, siegenite, bravoite; and oxidized particles: iss, bornite, chalcocite, covellite, magnetite, hematite, and goethite. Dust from a secondary copper refinery were found by RLM and SEM to consist of tenorite, cuprite, cassiterite, two silicate phases. Magnetite, hematite, Fe-Al-Cr-Mg spinel, periclase, forsterite, and wollastonite were derived from the furnace linings during initial cleaning.

Jan 1, 1992

By J. P. Evans

The modem 'copper smelter today utilizes tonnage oxygen for smelting concentrates. ,generating a high strength S02 off-gas leaving the smelter vessel. This gas stream. which also contains any unreacted oxygen, plus CO2; N2 and H20. also carries with it the volatilized portion of heavy metals in the feed, plus partly oxidized sulfide concentrates, The time/temperature history and subsequent treatment of this off-gas stream emerging from the smelting furnace exit up to the acid plant can influence the partitioning and segregation of heavy metals, in the off-gas circuit. Depending on this history. the type and characteristics of the chemical and physical reactions which occur in the gas handling system 'can be influenced. This fact can also be used as a tool to adjust the separation of copper from heavy metals. In this paper, the impact of different time/temperature histories of the gas, due to different furnace geometries and design. on the subsequent formation and characteristics of the smelter dust is examined. Based on the available data. several case histories drawn from examples using both bath and flash smelting technologies are analyzed from this perspective.

Jan 1, 1992