Search Documents

By Torma A. E.

Biotechnological processes are considered to be cost effective especially for situations where the recovery of metals from 'Very large volumes containing trace metal concentrations (less than 10 ppm) is concerned. Microorganisms, alive or dead, or their products can be highly efficient and selective biosorbents for metal concentration. It is important that the metal bound to the biosorbent can be stripped by suitable agent(s) and regenerated for repeated use. The stripped solution should be concentrated enough to be introduced into the common metal recovery circuit. The industrial acceptance of biosorption processes is dictated by increased competitive advantage over other processes. This paper reviews the pertinent literature?, regroups the information, and points out future possibilities for the mineral and metal processing industries.

Jan 1, 1992

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off-gases from the copper and nickel flash smelting furnaces and converters in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are pre¬sented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By Zhang Yongzhu

Sulfoxides are one kind of extractants for precious metals. The structure, the coordination reaction, the extraction behaviour and the precious metals complexes of sulfoxides are summarized. The differences between sulfides, sulfoxides and sulphones are also discussed.

Jan 1, 1992

By John L. Hostetler

GALFAN, the Zn-5% Al-mischmetal hot-dip galvanizing alloy is coated onto steel sheet, wire, and tube using high-speed continuous galvanizing lines. Factors critical to producing high quality GALFAN are reviewed, The relationship between minimum mischmetal content in the GALFAN alloy and furnace dewpoint will be described. The relationship between peak annealing temperature and furnace dewpoint will also be shown. Typical suategies for operating multi-purpose hot-dip galvanizing lines including GALFAN will be described. A recent development has allowed preparation of steel smp for GALFAN coating using aqueous fluxes rather than high temperature annealing. This allows production of GALFAN-coated smp without over-ageing of the steel, and allows high steel strengths and hardnesses to be obtained. The principles of this process will be described.

Jan 1, 1992

By N. L. Piret

Reprocessing of low zinc-bearing residuals with a zinc content of less than 10%, originating from the iron and steel industry, has been given more and more attention in the last few years, due to the potential landfill liability and the increasing cost of disposal by dumping. Whereas, recycling of hazardous electric arc furnace dust is already being performed commercially on a large scale in the U.S., Japan and Western Europe, almost no reprocessing takes place in the case of these low grade zinc-bearing materials. In blast furnaces and basic oxygen furnaces dusts and / or sludges are generated at a rate of 1 to 2 % of the respective production. The technologies for the retreatment of these types of materials, either commercially available or still being developed are briefly described hereafter. They involve internal recycling, upgrading by physical separation methods, separate hydrometallurgical processing and pyrometallurgical treatment. Their scope and limitations are critically assessed in terms of technological applicability, economic feasibility and environmental compatibility. Since, the possibtlity of achieving economic profitability is unlikely with this type of material, the main criteria for acceptability of the treatment process are: generation of a iron-rich material, suitable for treatment by the iron/steel industry, acceptance of the non--ferrous metal-bearing sub-product by zinc smelters, generation of non-hazardous waste materials.

Jan 1, 1992

By Gary R. Adams

Coating thickness control is typically difficult with touch-up solders for galvanized steel, and corrosion properties and abrasion resistance are sometimes poor. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with zinc-tin based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix The mouldability was dependent on the microstructure of the starting material, and optimum structures could be obtained through control of casting solidification rates and/or by the addition of small amounts of copper. Hardness and preliminary corrosion test results showed potentially good mechanical and corrosion behaviour. The absence of toxic materials ensures environmental friendliness. Comprehensive performance testing is continuing on selected experimental zinc-tin-copper touch-up solders.

Jan 1, 1992

By F. G. Prado

The technology for the extraction of zinc from zinc residues, such as zinc ashes, drosses and metallurgical flue dusts, by way of ammonium chloride solutions is well established, at least at the laboratory and bench scale levels. (3, 4) Zinc is soluble in ammonium chloride solutions in the form of zinc diammine chloride. Its solubility depends upon the concentrations and temperatures employed. The procedure and the equipment required are simple, and they can be applied either to small or large operations. As a by-product, zinc diammine chloride is produced with extremely low impurities in quantities which are stoichiometrically proportional to the zinc removed. The technology has been applied experimentally to galvanized steel residues. The dezincing results, including removal performance, energy and reagents required, and by-products are summarily presented in this paper.

Jan 1, 1992

By M. P. Bohrer

A closed-loop hydrometallurgical process has been developed for treatment of smelter flue dust generated by copper recycling. The process is a semi-continuous operation in which zinc, iron, and copper are first extracted from the dust with a sulfuric acid solution. The lead and precious metals, initially present in the dust, remain as solids and can be recycled to the copper smelting furnace. Cementation with iron and zinc metal purifies the zinc and iron-rich liquid stream prior to spray drying. The spray-dried product, consisting of a mixture of zinc sulfate monohydrate and iron sulfate monohydrate, is a desirable micronutrient additive for use in animal feeds. Treatment of the smelter flue dust in this manner will generate a positive return on investment, as well as mitigate a potential environmental liability.

Jan 1, 1992

By Alexandre Bonan

The paper reports on the results of a kinetic study on the oxidation reaction of aqueous free cyanide ions with H202, in the presence of Cu(2+) catalyst. The variables and respective ranges studied were the following: (CN) ° = 10 -100 mg/l pH = 10 -11 (H202/CN) mol ratio = 1 -3 (Cu/CN) mol ratio = 0 -0.25 The results lead to the development of a semi-empirical model whish incorporates both the useful oxidation reaction and the parallel alkaline decomposition of H202.

Jan 1, 1992

By I. Goy D. Gaballah

Decontamination of synthetic K2Cr2O 7 solutions containing 10 to 1000 ppm of hexavalent chromium using chemically treated barks have been studied at a laboratory scale. Metal removal from solutions depends on the pH, the initial concentration and the bark species. The use of a pulp density of 2 % in an agitated flask at the optimum pH for 2 hours leads to a percentage chromium removal of about 95 of the initial metallic ions content. Other trials conducted by column percolation permit the determination of the maximum retention capacity of the treated bark. Depending on the bark species, oak or pine, the rate of saturation is 110 and 215 mg of Cr per gram of bark respectively. The incineration of the metal charged barks gives recyclable, ashes containing 36 and 54 % of chromium metal for the oak and pine barks respectively. Experiments, of Cr6+ removal from industrial effluents containing up to 1800 ppm have been carried out on the semi-pilot plant scale. They have lead to the elimination of about 90 % of hexavalent chromium from this industrial waste solution. Further studies are conducted in order to define the hexavalent chromium binding mechanisms on bark constituents.

Jan 1, 1992

By Tomás Vargas

The catalytic influence of a pure strain of Thiobacillus ferrooxidans (ATCC 19859) on the dissolution of natural pyrite crystals was studied using electrochemical techniques. The results showed that this microorganism catalyze the leaching of pyrite by both, oxidizing ferrous iron in solution and depolarizing the reduction of ferric ion on this sulfide. In addition, studies of bacterial corrosion under applied potential showed that pitting on the pyrite surface centers on weak sites of the sulfide structure in which bacteria has attached, but occurs only when the ferric iron in solution induces an adequate level of anodic polarization on the mineral.

Jan 1, 1992

By Liu Zhonghua

Hydrogen reduction of cobalt sulfide (Co9S8) was experimentally investigated in the temperature range 813-1053 K. The results revealed that the reaction kinetics can be described by the shrinking core mod¬el in chemical control regime at low temperatures, it is of first order with respect to hydrogen concentration, and the reaction activation energy is 67.4 kJ/mol. The SEM second electron images of the samples before and after experiments showed that the swelling of the sample above 973 K is due to the formation of metallic cobalt whiskers.

Jan 1, 1992

By A. Dadgar

The adsorption kinetics of AuBr4 on Dowex ® -21K ion-exchange resin were studied and found to be independent of the initial gold, bromine, and base metals concentrations. A commercially-available undivided hypochlorite generating cell was used to generate bromine from simulated mixed halide (Br-/CI-) solutions. Electrolyses were performed with solutions containing very low Br' ion concentrations. The current efficiencies were 80-90%, and Br- ion utilization was maximized. A detailed economic assessment was made considering the capital and the operating costs for a 1000 mtpd gold ore processing plant. The toxicity and discharge levels of bromide, bromine, and cyanide were compared from a detailed analysis of the published literature data. Comparing bromine vapor with hydrogen cyanide gas for a given length of exposure, the lethal concentration of bromine is about 3 times less than hydrogen cyanide. The toxicity of sodium bromide is similar to that of sodium chloride. Acute poisoning to bromides and chlorides is rare because of their low toxicities. The allowed discharge levels of Br-, Br2, and CN- in fresh water are 250, 0.1, and 0.005 mg dm-3, respectively.

Jan 1, 1992

By Kurt Westerlund

The design of the economically most profitable and technically most feasible smelter process gas handling .and treatment as an integrated part of the total metallurgical process is discussed and exemplified, with alternative flow sheets including material and energy balances, investment and operating costs. Retrofitting and de-bottlenecking of existing gas handling lines will be described and exemplified. Methods of increasing total gas handling line availability will be described.

Jan 1, 1992

By Kurt Westerlund

The design of the economically most profitable and technically most feasible smelter process gas handing and treatment as an integrated part of the total metallurgical process is discussed and exemplified, with alternative flow sheets including material and energy balances, investment and operating costs. Retrofitting and de-bottlenecking of existing gas handling lines wil1 be described and exemplified. Methods of increasing total gas handling line availability will be described.

Jan 1, 1992

By J. Boltano

This paper discusses the study, design and implementation of the new gas handling system for the Caletones Smelter of Codelco-Chile. A discussion on design conditions for a future Sulphuric Acid Plant using Teniente Converter gases is also included. The old system which started to be modified in 1985 and relied on natural draft and used balloon flues, resulted in a limited gas handling capacity for operation under future process conditions. This system also caused excessive fugitive gases in the smelter working areas. The new system permits handling of process gases from the higher capacity Teniente Converters Installed in 1987-1989 improving the gas handling of the reverberatory furnaces and Peirce-Smith converters as well as the environmental conditions of the smelter. This system utilises improved converter gas hoods, evaporative cooling and electrostatic precipitators gas cleaning, and is based on natural draft.

Jan 1, 1992

By C. E. Hunt

Since the turn of the century, copper-nickel sulphide ores have been processed at the Sudbury, Ontario operations of INCO Limited, currently the largest integrated mining, milling, smelting and refining complex in the free world. Through the years operational, ecomomic, social and legislative changes have dictated the need for research and development directed at mitigating the impact of existing operations on the surrounding natural environment and also the reclamation of areas affected by earlier mining activities. Approximately one hundred years of mining history and the current annual processing of some 12 million tons of ore presents significant challenges with respect to waste disposal, liquid effluent treatment and land reclamation, particularly in light of rapidly evolving environmental regulations' and controls within the Province of Ontario.

Jan 1, 1992

By James A. Sommers

Hydrolysis of NbC15 is used to recover oxide values for ceramic and metals production. Reaction of NbC15 with water is rapid, exothermic and vigorous, yielding a gelatinous slurry. In contrast, dissolution of NbC15 in 12 N HCl is endothermic, resulting in a clear yellow solution. Such solutions can be de-hydrochlorinated by controlled contact with air, to precipitate a tantalum¬rich solids, depleting the liquid of its tantalum content. In this way, cheap, useful Nb-Ta partial separation is achieved. The separation is based upon differential oxide-chloride stability. Nb2O5 with <200 ppm Ta/Nb has obtained from starting levels of 2000 ppm. Observations are made on the different types of hydrolysis.

Jan 1, 1992

By Avijit Moitra

The behavior of the solidifying shell in the early stages of solidification has an important influence on the final quality of continuously-cast steel slabs. In order to understand the thermal and mechanical behavior of the shell, a two-dimensional transient piecewise-coupled finite-element model has been developed. The model simulates a transverse section of the slab as it moves down through the mold and incorporates the effects of heat conduction, solidification, shrinkage, turbulent fluid flow, thermal distortion of the mold and the visco-plastic behavior of the steel. Coupling between the thermal and the mechanical model is based on the mutual dependence of heat transfer across the interface between the shell and the mold and the size of the gap. The effects of mold distortion and taper on the gap size are also included. The effect of fluid flow has been incorporated via a heat flux imposed at the solid-liquid interface, which is obtained from a separate fluid flow model. The high temperature creep and plasticity of the steel is incorporated through a unified constitutive law defining the inelastic strain rates as a function of temperature, time and stress state. The model can be applied to various problems in continuous casting, such as the formation of surface defects and the design of mold taper.

Jan 1, 1992

By K. S. V. L. Narasimhan

Recently developed high energy permanent magnets SmCo5, Sm2Co17, Nd2Fe14B offer an interesting study of magnetic phenomenon. This publication discusses briefly the evolution of these magnets and the origin of the coercive force. Atomized SmCo5 coarse particles (150 to 300 microns) exhibit unusually large coercive force contrary to the experience in cast alloys. A brief discussion of utilization of these magnets into devices is also presented.

Jan 1, 1992