Search Documents

By D. Constantinides

In 1981 a Zn-Ag-Pb deposit was discovered in the vicinity of Molai, Greece. Subsequently, it was determined to be of the Kuroko type. The geology of various areas in the southeast Peloponnesean Peninsula is similar to that of the Molai deposit. Since favorable geologic criteria are present, absent, or unknown in varying degrees in all areas, it was deemed necessary to classify and rank the prospective areas according to the level of information available. For each level of information, an ore discovery model based on pragmatic exploration criteria was developed, enabling the favorability of occurrence to be calculated for each area. A Monte Carlo simulation was used to calculate the probabilities, the input data consisting of quantitative and qualitative estimates of the geologic criteria for each area. Three levels of information were modeled : Level A consisted of 9 criteria, level B of 12 criteria, and level C of 20 criteria. The three levels of information were tested on the Molai area. The results exceeded expectations, showing the gen¬eral trends which control mineralization at the lowest level of information. With an increase in the level of information, geological trends become more evident and a differentiation can be made between areas containing Cu mineralization, exhibiting a low probability, and areas likely to contain Zn-Ag-Pb mineralization. The models were then applied to the neighboring areas - only level A and B were available.

Jan 1, 1986

The ventilation of a mine is one of the key elements to a successful mining operation. It is, or should be, one of the primary concerns of the mining engineer at an underground mine. Too frequently, however, insufficient thought is given to future requirements. As a result, the mines suddenly find themselves with ventilation problems that cannot be corrected economically, or in short order, and have to suffer the consequences of being on the verge of having units shut down from time to time until the venlilaltion system can be improved. Insufficient ventilation in capital-intensive mining can cause production losses, the values of which far outweigh the significant costs of providing and operating an adequate ventilation plan. Many theories, and techniques in planning and control of underground ventilation systems have been developed over the years . It is the intent of this paper to point out some of the fundamental concepts, from the practical point of view, in the design and operation of a ventilation system, with special reference to underground mines using a room-and-pillar method.

Jan 1, 1986

By V. V. Ershov

Application of computers in the study of mineral deposits pursues two main objectives: 1. obtaining reliable information on the properties of the orebody; 2. providing graphic presentation of this information for its optimal use. These problems are successfully solved if, during preparation of graphic computer software, we apply modern mathematical methods. The present paper treats the problems of using geostatistics for graphic modelling of deposits by means of graphic computers. It should be noted that in this field geostatistical methods may be used for: a) indices evaluation in the nodes of regular grid, or in given blocks, by means of kriging, for its designated purpose; b) for evaluation of accuracy of interpolation methods, traditionally used in computer graphics, and not being optimal.

Jan 1, 1986

By James C. Burrows, Frances Kramer Mesher

Tungsten-containing ores are mined on all continents of the world. China is the world's largest producer and controls the world's largest reserves. The USSR, itself a sizeable producer, is estimated to be the world's largest consumer. The major use for tungsten in the noncommunist world is in production of cemented tungsten carbides for cutting, drilling, and wear parts. Other major uses include lamp wires, steels for tools, and armaments. Real tungsten prices have been in a general decline since 1977-1979 as the tungsten market undergoes basic and lasting structural changes.

Jan 1, 1986

By John W. Scott

INTRODUCTION The design criteria for a particular concentration and dewatering project will provide the formal basis for design of the process, equipment and facilities. These criteria will specify the required capacities and operating schedules for the equipment, as well as the quantity and quality of the feed to be processed and products obtained. The general climatic and geographical conditions at the site, specific information on soil or rock conditions; and applicable design standards and codes will also be included. The design criteria will generally be based on an interpretation of testwork carried out on the particular ore and site, and will thus parallel in detail and completeness this testwork. As the project moves from the early conceptual phases through to final detailed design, the design criteria will be developed and become more detailed as information is generated and made available for use. The design criteria are critical to the design effort as the formal specification to the designer of what and how much is to be processed, what and how much is to be produced, and where and under what conditions. The actual design criteria will be a formal tabulation of the design basis information developed for the project in question. For a preliminary study, this may consist of a single page of data; for a feasibility study several pages and for a detailed design up to several hundred pages and multiple volumes. Depending on the complexity of the process and the level of detail included, each project will be unique to some degree. The design process for a project normally progresses from preliminary conceptual phases through to a final detailed design. The criteria used for the initial concepts are generally developed from rough data and preliminary testwork on the ore in question. Regardless, the plant throughput and products are defined, thus giving a scope and definition to the study phase. In some studies a range of throughputs may be analyzed in order to arrive at the most economically attractive size for the proposed operation. This optimum size is then used as the design throughput for the more detailed design phases. Similarly as more testwork results are available and the ore characteristics and process become more well defined a continuous updating of the design criteria is undertaken.

Jan 1, 1986

By Stanley R. Riggs

Extensive phosphate resources occur within the Miocene Hawthorn and Pungo River Formations which have not been considered in the past since they were poorly known and were not available to conventional mining. These resources include 1) deep phosphates that occur below 75 meters of overburden within major sediment basins throughout the southeastern coastal plain, and 2) offshore phosphates that occur on the continental shelf and within the U.S. Exclusive Economic Zone (EEZ). The future potential of these two vast resources will be realized with development of new mining technologies such as hydraulic slurry mining and integrated with advanced technolgy already being utilized in the offshore petroleum industry.

Jan 1, 1986

By D. L. Kiser

Conventional and advanced coal preparation technologies were investigated through both a literature search and through direct contact with investigators and developers. In addition to a brief description of each process, performance characteristics including feedstock type, ash and sulfur reduction, thermal energy recovery and cost are provided in a tabular form. Seven of the most commonly utilized conventional coal preparation processes, including those respectively accepting coarse, intermediate and fine coal feed, were reviewed. It was found that certain properly implemented and well maintained conventional processes were capable of better than 75 percent ash removal while recovering 90 percent or more of the inherent thermal energy. Almost 50 advanced coal preparation processes were investigated based on biological, chemical and physical principles. Physical processes investigated included cycloning, homogeneous heavy media, electrostatic, high gradient magnetic, flotation and selective coalescence. Using pulverized coal as a feedstock, some of these processes are respectively reported to be capable of removing better than 95 percent ash. 95 percent pyritic sulfur, and 50 percent organic sulfur while incurring energy losses of less than 5 percent.

Jan 1, 1986

By R. Karl Zipf, Z. T. Bieniawski

Based on the premise that understanding the fundamental mechanics of fine fragment formation in coal will lead to reducing coal dust problems in mines, a thorough study of the mechanics of crack propagation in coal was undertaken. Two approaches were considered in an attempt to understand and quantify the fracture process as it relates to fine fragment formation. In one approach, theoretical models are used which describe the size of the fracture process zone which may relate to the amount of structural damage and fine fragment formation on the new crack surface. The other approach is based on the relationship between crack tip stress intensity and new surface appearance for mixed mode crack propagation. Preliminary observations with a scanning electron microscope support the premise that fine fragment formation is related to fracture surface appearance and fracture initiation conditions. An experimental program designed to supply the input parameters for these approaches is presently underway. The experimentation features mixed mode fracture toughness testing, using a special mixed mode testing rig, and fracture velocity measurements with a crack propagation gage. The interpretation of this data via the approaches discussed will provide further under- standing of the mechanics of fine fragment formation in coal.

Jan 1, 1986

By J. M. Richardson, A. L. Mular

Metallurgical balances are fundamental to the successful design and operation of concentration and dewatering circuits. With computerized balance techniques gaining prominence in recent years, it is essential that engineers understand the basic principles that underlie the new methods, as well as the various applications for design of new plants and analysis of existing operations. This chapter discusses two important types of metallurgical balance: (1) steady-state design (2) operating data adjustment Application of computerized steady- state design balancing is demonstrated through the example of a typical copper concentrator flowsheet. Operating data adjustment to achieve a consistent balance is demonstrated for a typical concentrator operation.

Jan 1, 1986

By Kevin Hegerle

The Henderson Mill has operated over a wide range of production rates, feed grades, manpower levels and recovery targets since start-up in 1976. Henderson Mill personnel, both management and hourly, have successfully responded to these changes by not only maintaining unit costs, but by actually decreasing unit costs. Methods of cost reduction have included conventional austerity programs, innovative technological improvements and creative work schedules. This paper addresses both maintenance and operating cost reductions and efficiency improvements.

Jan 1, 1986

By R. L. Peyton

Risk analysis is used extensively in many engineering applications. Although its use in the field of dam safety has been limited in practice, it has received considerable attention in recent years in the dam safety literature. Thus far, it has been shown that risk analysis in the evaluation of existing dams has the potential for providing a more rational basis for decision- making because of its focus on the direct issues--likelihood of failure, likelihood of loss of life, and risk cost of damages. It provides for a logical balance between the risk a dam imposes and the degree to which rehabilitation is required, compared to traditional evaluations based on somewhat arbitrarily chosen design events applied to large classes of dams. Dam owners could benefit by optimizing the cost of remedial measures. Downstream landowners could benefit by minimizing the likelihood of flood damages. However, it is also clear that significant technical and policy issues remain to be resolved before risk analysis in dam safety is accepted and routinely implemented in engineering practice. An obvious and important potential application of risk analysis is its use by the state regulatory agency as an in-house evaluation tool, or even as part of regulatory policy, in the implementation of its state dam safety program. Adoption of such a policy would have an important impact on the mining industry. .Although no state dam safety programs are known by the writers to have officially incorporated risk analysis into their regulations, there appears to be considerable interest in the concept. In recent surveys 47 states agreed that the development and promotion of a risk assessment methodology for state dam safety programs should be encouraged (Tschantz, 1983; Tschantz, 1984). The issue has also received important attention within the Association of State Dam Safety Officials (1986). One state-Illinois-proposed regulations during 1986 to allow risk analysis to justify lower spillway requirements for existing dams (Illinois Department of Transportation, 1986). At the Federal level, the National Research Council has found risk analysis especially appropriate for assessing dam safety at high-hazard dams (National Research Council, 19851, the Bureau of Reclamation has published guidelines for incorporating risk analysis into their dam safety grogram (U.S. Department of the Interior, 1986), and the Federal Emergency Management Agency has recently sponsored workshops and supported research related to risk analysis in dam safety (Federal Emergency Management Agency, 1985a ; Federal Emergency Management Agency, 1985b; - - McCann, et. al., 1985a, 1985b).

Jan 1, 1986

By S. V. Tracy

The Outokumpu Skim-Air Flash Flotation machine was developed to separate valuable mineral from gangue as early as practical by floating it with specially designed flotation equipment installed in the grinding circuit. Machines already in service have shown the ability to produce final grade concentrate with an increase in overall recovery and flotation rate while decreasing filter cake moisture and reducing fluctuating feed grades to conventional flotation circuits. The first US production test was carried out in a southwestern copper concentrator with successful results. This report describes the results of the test along with an explanation of the process and the benefits obtainable.

Jan 1, 1986

By M. A. Georgiana

The Emerald Mine No. 1, located in southwestern Pennsylvania is presently owned and operated by Cyprus Minerals of Englewood, Colorado. High volatile bituminous coal is produced from the Pittsburgh No. 8 seam by both longwall and continuous mining methods. The coal is then mechanically cleaned on site utilizing a combination of heavy media separation and froth flotation methods prior to shipment to both the metallurgical and steam coal markets. The Emerald Mine is presently producing 2.8 million raw tons per year, while liberating approximately 6.5 million ft per day of methane. In light of the methane liberation rate, ventilation requirements have been significant and have always received utmost priority and consideration. Figure 1 shows the locations of the current and proposed shafts. Emerald utilizes two Joy (Model M120-58-880) axial vane fans on shafts No. 1, No. 2R, No. 3R. (one operational, one stand-by) The use of computer simulation of various ventilation networks was initially employed during the design stages (1975-1977) and has been utilized through the present. Obviously, the initial planning, under the ownership of Lykes Resources, was strictly theoretical. All the quantities were proposed and the resistances were based on prior simulations of other mines and mathematical formulas. However, once the mine was moderately developed, actual values were recorded and utilized. This procedure consists of: a) layout pressure and quantity points b) measure all air quantities where an air course splits

Jan 1, 1986

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986

By W. W. Kephart

The glass container industry is the largest producer of glass in the United States. As of this writing, there are approximately 89 active domestic production locations. In 1984, the industry shipped 11.8 million tons of glass containers. Approximately 70% of this production was clear or flint glass, 20% amber, 7% green, and the remainder miscellaneous colors. Although the production of nearly 12 million tons of glass is impressive, anyone following the industry over the last five years is aware that the industry has changed from a pattern of growth in the 1970's to one of maturity in the 1980's. Some observers, less generous, perhaps, have described the 1980's as a period of decline. In 1981, there were 119 production facilities which produced 13.2 million tons of glass the previous year. This equates to a 10% reduction in glass container production from 1980 to 1984, with a corresponding impact on the segment of the industrial minerals producers serving the container glass industry, as shown in Figures 1 and 2.

Jan 1, 1986

By J. M. Wood

Green algae have been found to be much more resistant to heavy metals than blue-green algae. Several mechanisms for resistance to toxicity have been recognized in laboratory strains of Cyanidium, Chlorella and Chlamycomonas. Cyanidium and Chlorella both grow at low pH in acid mine water. Cyanidium removes metal ions from solution by precipitation as metal sulfides whereas Chlorella complexes metal ions to the cell surface i.e. cell wall) and therefore functions as an efficient ion exchange vehicle. We have shown that Ca2+, Mg2+, K+ and Na+ are of critical importance in both the resistance and bioaccumulation of toxic heavy metals.

Jan 1, 1986

By R. O. Burt

Gravity concentration - the separation of minerals according to their relative density - is one of the oldest forms of mineral processing. Even though modern technology has developed a range of other processes, gravity concentration remains as one of the most important methods employed for mineral separation. The range of minerals recovered covers a wide spectrum, from andelusite to zircon, from coal to diamond, from gold to industrial mineral. The long history of gravity concen¬tration, along with a still imperfect understanding of the various mechanisms involved has resulted in a series of ingenious engineers developing, some¬times perfecting and sometimes rejecting, a wide range of equipment, suited for a variety of different duties. 'Selection' in the context of gravity separation, is primarily the choice of the right type of equipment for the separation in hand; 'sizing' of the correctly chosen unit is, more often than not, determining the appropriate number of units required to suit the throughput. The accent of this chapter will, therefore be 'selection'. A brief description of the major types of gravity concentration equipment will follow a discussion of the factors which determine the selection of the correct unit. CLASSIFICATION OF GRAVITY CONCENTRATION EQUIPMENT All concentration equipment has a primary function and a secondary function. The primary function is the efficient separation of the constituent minerals into two or more discrete phases; the secondary function is to effectively cause the discharge of these discrete phases into separate compartments (Aplan 1975). For maximum efficiency of operation, the forces which effect the primary function should not also result in the secondary function occurring; in such cases optimum operating conditions required for the primary function, separation, may have to be compromised to ensure reasonably efficient operation of the secondary function, product discharge. With gravity concentration, the primary function is effected by the relative movement of minerals of different density in response to gravity and one or more other forces, the latter often including the

Jan 1, 1986

By C. J. Savage

Rio Tinto Minera, S.A. operates in Southern Spain, at one of the most ancient mining sites in the world, using advanced computerised mine planning. This paper describes the development and application of the mine planning systems to the copper and gold/silver operations. It briefly covers the hardware configuration, and the advantages and improvements in mine planning achieved. The system's application started with the long term mine planning of Cerro Colorado (open pit) copper mine and was gradually extended to cater for the medium and short term planning requirements of the other operations of the Company. The base of the system is a mineral inventory established by the combined use of the geology and geostatistical methods, and compatible with the mine planning requirements. The planning system has three major components: one used for open pit design and long term mine planning, another used for blast evaluation and finally one used for short term mine planning. Recently, a fourth component has been added to the system for reconciliation between predicted and actual tonnages and grades. There is common data file transfer throughout the system.

Jan 1, 1986

Various computer packages are now available for balancing data obtained from complex concentration plants. It is well established that the filtered data generated by these programs are statistically better than the raw data. However the degree of improvement as well as the accuracy of the estimated variables depend strongly on the propagation of measurement errors through the estimation algorithm. Therefore, for the subsequent use of the filtered data, their confidence intervals are as important as the data themselves. Variance of filtered variables have been derived in a very general way for any arbitrary flowsheet and when data originate from various sources such as flowrates, chemical assays, particle size distributions and pulp percentages of solids. The theoretical formulae are incorporated in the BILMAT package for mass balance calculation and illustrated on various flowsheets involving grinding, classification and flotation. The validity of the proposed method is discussed by a comparison to a Monte Carlo approach, for a simple processing circuit.

Jan 1, 1986

By Robert A. Bauer

Geology and weather effects produce natural ground movements that may be misinterpreted as mine subsidence. Weather, local geology and vegetation clearly influence the elevation of the ground surface through frost action and changes in groundwater levels and soil moisture content. Common practices of monument and benchmark design and placement do not address the problem of natural ground movements. Monuments can be designed to minimize some natural ground movements. Differential displacements can be reduced by knowledgeable placement of benchmarks and monuments which are of similar design and construction. Commonly, the threshold values of movement for the determination of mine-induced subsidence are dependent on the closure errors (accuracy) of individual surveys. Accuracy is more than the amount of closure error; it should include the range of elevation changes (error band) determined for each monument over a period of time before it is disturbed by mining. Multiple baseline surveys of the entire monitoring system, conducted before the onset of subsidence, should be used to establish subsidence detection limits.

Jan 1, 1986