Search Documents

By Earl L. Rau

At the present time, whether an electric utility uses high-sulfur coal is largely determined by geographical location, clean air legislation, and the age of the power plant. Acid rain legislation may well be the new force to change the use of high-sulfur coal. A number of coal papers were presented at the SME Fall Meeting in St. Louis, MO, Sept. 1986. These papers discussed high-sulfur coal in relation to its economics, trends and prospects, value of cleaned coal, and coal-cleaning technology. The Clean Air Act of 1970 required the reduction of SO, emissions from most stationary electric-generating plant to 0.5 kg (1.2 lbs) SO2, per million Btu of heat input. It was possible for many plants to utilize lower-sulfur coal or a mixture of high-sulfur and low-sulfur coal to meet this emission requirement. This 1970 act greatly increased the use of low-sulfur western coal. The 1978 amendment to the Clean Air Act required all new plants to use Flue Gas Desulfurization (FGD) to meet a requirement of 70% reduction of potential SO2 emissions to 0.3 kg (0.6 lb) SO2 per million Btu of heat input. With the requirement to use FGD, there was little or no demand for low-sulfur western coal in new eastern power plants. If' new acid rain legislation is enacted, it likely will require sizeable reductions in SO2, emissions by existing coal users. There might then be a shift to greater use of low-sulfur coals. The low-sulfur coals could come from either western or eastern mines or from cleaned eastern coals. Economics will dictate the approach older power plants will take to meet new regulationsuse FGD or low-sulfur coal. Coal use for electric power generation has changed from 1970 to 1985. Table 1, (Land, preprint 86-333) shows the change. The table shows that in 1985, US utilities used about 255 Mt (280 million st) of high-sulfur coal. Some 45 to 54 Mt (50 to 60 million st) of high-sulfur coal is being used in plants equipped with FGD and most of this use is in eastern states. This leaves 200 to 209 Mt/a (220 to 230 million st) of high-sulfur coal being used without FGD treatment. These plants are at risk if acid rain legislation is passed. Most of these plants are in the east and are more difficult to supply with low-sulfur coal. Estimates range from $20 to $30 billion capital investment and from $5 to $9 billion dollars per year operating costs to reduce SO2, emissions from those old medium-to-high-sulfur coal-burning plants. G. W. Land, (preprint 86-333), also presents tables relating to power generating costs and coal types. The author's tables are extracted from Land's tables IV and V. Table 2 here presents costs for a new plant. This includes the impact of different heat rates, fuel costs, fuel qualities, operating and maintenance costs, labor costs, and waste disposal costs. Table 3 compares estimated costs to retrofit an older plant with a limestone scrubber versus switching the same plant to low-sulfur eastern or western coal. Costs of switching include upgrading the electrostatic precipitator and - with western coal - costs of derating. Bhagwat, (preprint 86-325), details the trends in high-sulfur coal markets from 1974 to 1984. He also gives some prospects for high-sulfur coal markets, 1984 to 1994. The prospect depends mostly on whether acid rain legislation is enacted. By 1994, if New Source Performance Standards (NSPS) continue to be applied, high-sulfur coal demand from six mid-west and eastern states is expected to increase by 27 Mt (30 million st). • L. A. Khan and J. W. Baxter, (preprint 86-373), discuss several coal cleaning technologies such as froth flotation of fines, bulk oil separation and oil agglomeration, oil agglomeration/flotation, and air-floc flotation. ? (Space limitations preclude listing references. A complete list is available from the author.)

Jan 1, 1987

The following errors were inadvertently included in "How millisecond delay periods may enhance or reduce blast vibration effects" by R.M. Wheeler in the September issue of Mining Engineering.

Jan 1, 1987

By S. G. Malghan

This paper reviews uses of sodium sulfide in the flotation of oxide minerals of copper, lead, and zinc. The activation and depression effects of sodium sulfide are of particular importance because of their applications with oxidized lead and copper ores. In spite of its industrial importance, the nature of the heterogeneous reactions between sulfide ions in solution and the surface of oxidized minerals has not been fully understood. Hence, proposed mechanisms of the sulfide action in flotation, methods of measuring and monitoring sodium sulfide in flotation pulps, and variables influencing the sulfide addition are analyzed. Recent studies on sodium sulfide addition to flotation pulps, monitoring its concentration, and the optimum dosage control using platinum and/or sulfide specific ion electrodes are discussed.

Jan 1, 1987

By K. A. Brame, L. G. Austin, R. S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-ordering grinding studies in a laboratory ball mill according to the Austin, Klimpel, and Luckie procedures. The results were scaled to five larger mills of 0.56, 0.82, 8.36, 4.41, and 5 m in diameter assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distributions and capacities for batch grinding in the smaller mills and open-circuit grinding in the larger mills. The predicted capacities were in approximate agreement with experimental values except for the 5-m diam mill. The Bond method gave capacity predictions that were 4570 to 150% too high.

Jan 1, 1987

By Dirk van Zyl, Clint Strachan

A study was conducted to assess the feaeibility of increasing the heap height above one lift at the Alligator Ridge Mine. This study concentrated on the physical aspects of the heap and liner performance. Two principle aspects were addressed during this investigation: (a) the adequacy of heap permeability under present and future loading conditions; and (b) the adequacy of the liner to limit seepage losses. Field and laboratory test a were performed and their details and results are presented. It was concluded that the permeability of the heap would remain adequate for higher heap. The geometry of the heap will be the major constraint. It was also concluded that the liner would perform satisfactorily beneath higher heap.

Jan 1, 1987

By A. I. Arol, I. Iwasaki

Clay minerals adversely affect the selective flocculation of iron ores. The effect of montmorillonite on a hematite-quartz mixture was studied. Montmorillonite, particularly in the presence of Ca++, caused indiscriminate dispersion of the pulp. Three possible mechanisms were postulated, namely, card-house structure formation, adsorption of dissolved species from montmorillonite, and montmorillonite- hematite interaction. It was determined that hetero- coagulation of montmorillonite on hematite was responsible for the behavior. Flocculation tests, montmorillonite abstraction tests, starch adsorption tests, zeta potential measurements, and surface analysis techniques were used to ascertain the montmorillonite-hematite interaction and to account for the manner in which it affected selective flocculation.

Jan 1, 1987

By Phoebe L. Hauff, Jeffrey P. Kurtz, Paul D. Chamberlin

Clay minerals can be a source of problems in heap leaching operations. The ore for many heap leach operations is commonly acid-sulfate alteration zone rocks which may be found in hot springs deposits as well as the supergene zone of other near- surface gold deposits. Clays can be important constituents of these ores. Swelling clays, such as smectite, can come loose from the agglomerated ore, migrate within the heap, concentrate in pore spaces and often plug up flow channels in the heap Cement is often added to the ore as a binder during the agglomeration process. Lime is added for pH control. Their presence, combined with the sodium cyanide commonly used to leach, can raise the pH of the leach solution to 10 or even 12. This very alkaline solution can cause dissolution of some mineral Some clays, such as kaolinite, are not very stable in high pH solutions. They can be dissolved and reprecipitated as other clay species if sufficient silica and the appropriate cations are available in solution. Silica gels and amorphous materials can also be created from the dissolved kaolinite and other minerals and act as retardants to the flow of leach solutions in the heap. Therefore, before a heap leach operation is built, the operator should evaluate the clays in the ore and test the agglomeration procedure. It is important to know not only the mineralogy and the chemistry of the leach environment but how the minerals and solutions interact and what the products of this interaction are. A hypothesis is presented in this paper that expanding smectite- bearing clays can be generated within the heap. How and why this happens will be explained.

Jan 1, 1987

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987

By J. Bartrum, A. Bowler, G. Butcher

The purpose of this paper is to outline the design, specification, and operation of the 8.5-m- diam (28-ft-diam) SAG mill commissioned at Kidston Gold Mines during January 1985. Amenability of Kidston ore to SAG milling, coupled with substantial cost advantages, led to the specification of this mill, equipped with variable speed drive to overcome the large variation in ore hardness. Operation of the mill is effected via a number of automatic control loops. Problems experienced with automatic control plus other electrical and mechanical failures have led to design changes and the formulation of future operating strategies.

Jan 1, 1987

By D. S. Holmes

Biological processes for metal solubilization and ore beneficiation are in widespread use today. There are also some promising new applications of biotechnology in the areas of metal concentration and toxic metal cleanup. Recent progress in genetic engineering promises both to revolutionize the existing biological process and to expedite the adoption of the new biological applications. But before it can do so effectively, progress must be made in many areas of fundamental research and in biochemical engineering. These issues are addressed with special reference to the biotechnology of semi-enclosed containers (bioreactors), dumps, heaps, in situ and under- ground leaching, and with respect to the biotechnology of metal concentration. Finally, certain biological considerations for bacterial strain improvement are discussed.

Jan 1, 1987

By B. H. Richard, P. J. Wolfe, T. G. Holdeman

Guided seismic wave propagation was studied in the Lower Freeport (6A) coal seam in the Oak Park No. 7 mine near Cadiz, OH. Three component geophones were implanted in the coal at distances ranging from 72 m to 183 m from the seismic source. Both Love- and Rayleigh-type modes were observed but the Love-type mode produced the best data. Detailed analysis was performed on the best Love data and a Dziewonski map of group velocity vs. frequency was constructed. This map was in excellent agreement with a theoretical dispersion curve calculated for a model of the coal seam. The Love wave group velocity was found to have a minimum value of 510 m/sec at 275 Hz. Only the fundamental mode contributed significantly to the observed signal and it was observed up to the maximum distance available.

Jan 1, 1987

By R. E. Weeks, D. J. Millenacker

Utilization of true in situ technologies for mining copper in Arizona will involve a complex environmental permitting process. This process is a key factor in determining the feasibility, costs, and implementing time- frames required for development of this innovative mining method. The regulatory structure in Arizona is presently changing due to enactment of the Environmental Quality Act (EQA) of 1986 and development of new aquifer protection rules and regulations. The US Bureau of Mines has reviewed the comprehensive hydrogeologic characterization, ground water monitoring, mechanical integrity testing, well construction, contingency planning, and other regulatory elements that will serve as mechanisms to assure protection of ground water resources. The purpose of this paper is to inform the domestic copper industry of the significance of the new Arizona regulatory structure and its implications for prospective in situ operators.

Jan 1, 1987

By S. L. Bolivar

The Prairie Creek intrusion, near Murfreesboro, AR, is the site of the most famous diamond mine in North America. Three major rock types are associated with the intrusion-a hypabyssal peridotite, a volcanic breccia in which the majority of diamonds occur, and tuft. Previous studies, including geological, geophysical, petrological, and whole-rock and mineral chemistry are reviewed. The recent suggestion, by other workers, that this intrusion may be more correctly called a lamproite is examined. This has serious implications for diamond exploration in Arkansas and elsewhere in the US.

Jan 1, 1987

By E. M. - Technical Papers Spokes

A.B. Rushton The work and resulting publications of the Committee on Underground Coal Mine Safety and The President's Commission on Coal were appropriate at the time of publication. The statistics cited in the publications appeared to be valid, and the actions proposed by the committee had merit. Although the actions proposed to achieve further improvements in safety may have been worthy of repeating, to associate statistics (Table 1) that are seven to eight years old with company names is bad. Statistics are readily available from the Mine Safety and Health Administration (MSHA) and are usually within three months of being up to date. A review of the most recent Coal Controlling Co. Report will reveal significant changes in the rankings. The more recent statistics should have been cited, or at least compared with those used in the article. Westmoreland Coal Co. is listed as having a 21.1 disabling injury rate for the period (1/78-12/80). The disabling injury rate for the Company for the year ending 1985 was 7.4 for the underground mines and 6.25 for the total facilities. Through March 1986, the dis- abling rate for the underground mines was 2.86. The management and employees of Westmoreland Coal Co. are committed to safety. The improvements achieved over the past five years attest to that commitment. We are justifiably proud of the achievement and dislike being misrepresented as in the April 1986 article Reply by E.M. Spokes I regret that the lapse of time since the original work gives a picture of safety practice that is no longer true today. That Westmoreland has reduced its disabling injury rate by 65% to 7.4 in 1985 is most commendable, and I congratulate you for this accomplishment. It is typical of the progress sought by the National Academy of Science and National Research Council when they funded the original study and published "Toward Safer Underground Coal Mines" in 1982. If a significant number of companies do as well as Westmoreland, the report will have served its purpose. Since the paper was primarily a condensation of the original report, it would not have been appropriate to seek access to later statistics. The purpose in seeking its publication at the time of presentation was to reach those who might have missed the original report. The fact that publication was delayed has not voided that purpose and may have reminded some who were aware of the original that its recommendations still apply to improvement of underground coal mine safety

Jan 1, 1987

By J. G. Smith, L. P. Sheets

Introduction Potential applications that exploit the electrical properties of coal measure rocks include: (1) radar sensing of coal face, floor, and roof for automated mining operations; (2) underground wireless communications; and (3) sensing extent of subsidence, blasting operations, coal gasification bums, and moisture migrations. Impediments to exploitation of electrical properties include: (1) a lack of reliable electrical properties data for in situ conditions and (2) a lack of correlation data between electrical properties and other relevant physical properties. In this paper data are presented for electrical conductivity and permittivity for Appalachian and Illinois shales for a frequency range 2 x 10 to 2 x 10 Hz. These data are useful in establishing in situ electrical property variability, lower limits, and anisotropy. Electrical proper¬ties measurement and values for other coal measure rocks are discussed as well. Laboratory measurement For the frequency range investigated, a capacitance bridge and Q-meter were employed. These instruments are designed to yield bulk values of permittivity and conductivity. Disk samples of thickness 0.396 cm (0.156 in.) and diameter 2.54 cm (1 in.) were machined from cores obtained from the two coal basins. While both the capacitance bridge and the Q-meter must be balanced manually, the bridge has an analog-to-digital interface and an attached computer specifically designed to expedite data collection and interpretation. Sample holders are critical components in the measurement process. A Hartshom-Ward holder was employed with the bridge and a Marconi micrometer jig was used with the Q-meter. Neither commercial sample holder was designed to regulate ambient humidity conditions. Because water adsorbed on sample faces may cause errors approaching 100%, special enclosures were designed for both holders. Each enclosure contains a flush-mounted externally-manipulable carousel, an externally-manipulable rigid arm that can accomodate translational motion and three-dimensional rotation, a compartment for humidity regulating solids or liquids, and a humidity sensor. Each enclosure will accomodate several samples that can be manipulated within the enclosure without opening it. Experience gained during this research demonstrated that humidity regulation was necessary to obtain repeatable results. Grinding and polishing shale to a very thin thickness (about 0.4 mm) was shown to cause changes in electrical properties as well. These latter changes were attributed to alterations in the water content. Theoretical considerations A very comprehensive discussion of the electrical properties of sedimentary rocks is available in literature (Sen and Chew, 1983). These authors reviewed the work of others and proposed modifications to better explain the frequency dependent behavior of the permittivity and conductivity of rocks. A large portion of their article was devoted to explanations of large relative permittivities at low frequencies such as observed in this research. They noted that the electrical properties of formations containing shales and clays are the most difficult to explain. Sen and Chew noted the need for additional experimental data and further refinements in theory. Results Shales, limestones, and sandstones were examined for a single 150-m (492-ft) core from Pennsylvania and for a dark shale from a southern Illinois coal mine. Figures 1 and 2 illustrate the conductivities and relative permitivities for the southern Illinois dark shale at a single location. The differences in electrical properties clearly

Jan 1, 1987

By J. J. Daniels

Advances in borehole geophysical research for mineral assaying and remote detection of mineralization away from the borehole are cited. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and X-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before non-linear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive ore bodies that are not intersected by a drill hole. Hole-to-surface resistivity and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drill hole.

Jan 1, 1987

By D. L. Passmore, J. D. Bennett

The reliability of mine operators' reports to the Health and Safety Analysis Center of the US Department of Labor of days lost from work by injured miners is 0.267.

Jan 1, 1987

By S. Gundiah

Preparation of functionalized polymers from the polymerization of monomers and preformed polymers are discussed with a few illustrative examples. The methods of their characterization, with reference to their application in flocculation, are described.

Jan 1, 1987

By S. B. Bhagwat

Equipment capacities of a sample of Illinois surface coal mines representing about 60% of surface production in the state were studied. Available equipment capacity was compared with the required capacity, as indicated by coal production and stripping ratios reported. Most mines sampled showed surplus equipment capacity, which if avoided, would result in substantial cost savings. The surplus capacity results mostly from market fluctuations that result in underutilization of equipment. Study findings underline the importance of market assessment at the time of mine planning and of communication between marketing and engineering arms of a coal firm.

Jan 1, 1987

By L. B. Rothfeld

Two new coal use technologies are on the verge of commercial acceptance by the utility industry: atmospheric fluidized bed combustion (AFBC) and gasification combined cycle (GCC). Generating plants under construction or in planning will replace older pulverized coal (PC) boilers or substitute for new PC boiler capacity. This paper reports recent developments in the commercialization of AFBC and GCC, emphasizing the potential impact on the coal mining industry. The influence of coal quality characteristics on fuel selection is explored by means of preliminary economic calculations for different coals and competing fuels.

Jan 1, 1987