Search Documents

By Craig E. Burson

This paper discusses the relationship between frother types and coal flotation as a function of particle size. It has been found that each frother has a unique size fraction that it will float effectively. This fact is very important when it comes to selecting a reagent scheme that will provide maximum recovery of both coarse and fine particles. Improvements in recovery can be attained when the chemical relationships between frother type and particle size floated are understood. Data from plant evaluations using commercial and developmental frothers are presented to verify the importance of frother types versus size fraction floated.

Jan 1, 1987

By C. R. Jenkins, G. S. Taylor

Three sedimentation ponds had their performance evaluated before and after installation of modifications. Each pond had a floating baffle installed, two had siphon outlets, and one had a floating outlet device. Baffles inhibited short circuiting, and the outlet devices retarded flow following a rainfall event and drained the pond, creating a large storage volume to maximize detention time. Total suspended solids and settleable solids tests were measured on samples of influent and effluent to evaluate pond performance. Particle size analyses were conducted on samples containing measurable amounts of solids. Performance improved in each pond, with baffles providing the major improvement.

Jan 1, 1987

By Edward J. Miller

Explosions and fires are without a doubt two of the most feared occurrences in modern underground mines. When they result in loss of life or substantial property damage, they usually gain world-wide media attention and have, on occasion, provided the impetus for legislative action. The very involvement of the Federal Government in mining was the result of a series of explosions which resulted in the loss of hundreds of lives. Fortunately, explosions of this magnitude are rare. Fires and explosions of lesser consequence are, however, more common and their severity may be more a matter of luck than anything else. The publicity which these events receive is usually restricted to the area immediately surrounding the mine and a1 though MSHA and sometimes the state prepare reports of their investigations, the general mining community is quite often aware of the circumstances surrounding these occurrences. This paper will discuss some of these "lesser" explosions which have occurred recently. These explosions have sometimes occurred in sealed or otherwise inaccessible areas of the mine involved, where conventional ignition sources such as electrical power were not present.

Jan 1, 1987

By R. Houot, C. Leschevin, G. Gillet

In mineral processing, conventional magnetic separators are equipped with traditional magnetic circuits (magnetic iron yoke with copper coils or iron-clad solenoid) that develop magnetic fields of less than 2 T'. For minerals of low magnetic susceptibility, use of these circuits has many disadvantages. Only a separator with a superconducting magnet can contribute to solving the problems and produce a high magnetic field. This paper presents and describes a magnetic separator having a superconducting magnet with integrated closed circuit for helium liquefaction. The system generator and maintenance are simplified by extensive automation realized by a versatile program- mable autocontrol unit. A comparative study if the results on concentration and purification of different raw materials with the new and with conventional separators is described.

Jan 1, 1987

By A. W. Mitchell

Mining of a bedded barite deposit exposed highly pyritic siliceous sediments which have weathered and degraded subsurface and surface waters. The ph, sulfate, and total dissolved solids are the most seriously affected parameters. Several solutions were tried and eventually horizontal holes were drilled into the mine wall to draw down the water table and decrease the movement of groundwater through oxidizing zones opened up by the mining operation. Areas of surface disturbance were capped with layers of soil, bentonite, and gravel to decrease the infiltration of water into the disturbed areas. These actions have begun to decrease sulfate and total dissolved solids concentrations and increase ph values.

Jan 1, 1987

By Photios G. Ioannou, Guillermo F. Salazar, Herbert H. Einstein, Yeong W. Kim

The MIT tunneling group has developed, over the past decade, a number of decision support tools for the geologist and engineer, planner and designer, owner and contractor involved in underground construction. These computer based tools can be used in the planning and exploration stage of a project, in predesign and design, in construction planning and during construction. Tasks as different as optimizing information collection during exploration and during construction, as selecting major design alternatives in predesign and modifying design during construction, as providing cost and time estimation and considering social and physical environmental constraints, can be handled. Output can be in the form desired by the user ranging from geologic profiles (cross sections) to management reports.

Jan 1, 1987

By H. J. Sohn

Systematic studies were carried out on the adsorption of the silver thiourea complex on activated carbon. The experimental isotherm data fit the Freundlich isotherm equation. The adsorption rates increased with increasing temperature and decreased slightly with the increase of free thiourea concentration. The concentration of sulfuric acid had little effect on the adsorption rate. Adsorption kinetics correlated well with the Elovich equation, indicating adsorption is the rate-determining step.

Jan 1, 1987

By M. Ghiani

Biohydrometallurgy originated, some forty years ago, from an environmental problem, namely the serious pollution of the Ohio river by acid drainage water coming from neighboring subbituminous coal mines. Studies aimed at elucidating the cause of the intensive oxidation of the iron sulfide (pyrite) inclusions of those coals, led to the discovery of a bacterium, Thiobacillus ferrooxidans (Temple and Colmer, 1951), capable of acting as a catalyzer, accelerating the otherwise very slow chemical oxidation of iron sulfide to rates many orders of magnitude higher. However, it is now recognized that the biotechnology of microbial mining dates back to 1963, when the ability of this bacterium to solubilize copper from sulfide ores was ascertained (Razzell and Trussell, 1963). Much research has been carried out on biohydrometallurgy over these last 25 years and is still being actively conducted all over the world. The interdisciplinary nature of this young branch of science and technology is reflected by the variety of experts involved: microbiologists, mining engineers, hydrometallurgists, physico-chemists, mineralogists, solid-state physicists and biochemists. This intensive research effort has provided a solid background on the fundamentals of this technology, although many important issues have still to be solved, amongst which the enzymatic mechanisms controlling biocatalysis of mineral sulfides dissolution, the influence of bulk- and surface solid-state physics of metal sulfides on dissolution mechanisms, the interaction of the various strains composing natural microbial floras. Their elucidation should permit the rationalization of biohydrometallurgical techniques and the optimization of commercial processes. Biohydrometallurgy has already achieved satisfactory results: copper recovery from submarginal copper sulfide run-of-mine ores (i.e. assaying less than 0.3% Cu) by in-situ, dump and/or heap leaching is successfully practised in many countries and uranium recovery through bioleaching is competitive with other leaching processes.

Jan 1, 1987

By R. V. Ramani, R. Bhaskar

While the National Academy of Sciences has stated that gravimetric sampling technology for compliance purposes is adequate, research into various aspects of respirable dust control require data on many other parameters of airborne dust. These, in turn, have created the need to use many instruments, other than personal gravimetric samplers, in mine environments for dust measurement. There is a need to evaluate the performance of these instruments under conditions of potential use. As part of research in the Generic Technology Center for Respirable Dust, cascade impactors, gravimetric personal samplers and gravimetric samplers collecting dust using isokinetic sampling principles were employed for dust measurements under identical conditions in a mine airway. During the course of the experiments, 8-stage cascade impactors and gravimetric samplers drawing air isokinetically were located in the center of a mine airway at various stations. Two types of data were examined - concentration of dust and size distribution of the dust collected in the samplers. The data show that the amount of dust collected by an impactor is less than half the amount collected isokinetically. The size distributions of the dusts collected from the two instruments, though comparable, show a consistent difference in median diameters. The cause for this bias is examined. The paper presents and discusses the results of the tests, including the concentrations and size distributions obtained from the two instruments for different experimental conditions. There is a need to document the performance of various dust measuring devices in mine airflow conditions.

Jan 1, 1987

By B. H. Johnston, B. N. Doyle

Introduction In 1983-84 Kidd Creek Mines Ltd. in Timmins, Ontario, started up the second commercial zinc pressure leaching plant based on the Sherritt Gordon Mines Ltd. direct pressure leach process. The first plant using this process was that of Cominco Ltd. at Trail, B.C. (Parker, 1981; Martin and Jankola, 1985). The Kidd Creek plant was constructed to take advantage of the extra capacity that the existing purification, cell house, and casting sections had in comparison to the roasters and acid plant. In addition, pressure leaching offered flexibility in other areas such as treatment of low grade concentrates. The process design package and the detailed design of the autoclave system was carried out by Sherritt. The detailed design for the rest of the plant was done by Cambrian Engineering Ltd. under the direction of Kidd Creek. The construction and commissioning of the plant has been described earlier (Johnston, 1983). This paper describes, briefly, the application of the direct pressure leaching process for zinc concentrates and the integration of the pressure leaching plant into the main zinc plant at Timmins. It discusses some of the startup problems and changes made to the plant. The damage following a fire inside the autoclave is also described. The subsequent repair and recommissioning of the autoclave has enabled Kidd Creek to demonstrate the originally sought advantages of pressure leaching and to take advantage of their extra cell house and casting capacity to produce more zinc. Process principles The development of the direct pressure sulphuric acid leach of zinc sulphide concentrate at temperatures above the melting point of sulphur and at elevated oxygen pressure has been described in detail in a number of papers (Martin and Jankola, 1985; Johnston, 1983; Veltman and Bolton, 1980; Kawulka et al., 1975; Veltman et al., 1977). The most significant aspect of the process is that sulphidic sulphur is converted to elemental sulphur in reactions that can be simply described as follows. ZnS + H2SO4 + 1/2 O2 ZnSO4 + S° + H2O (1) FeS + H2SO4 + 1/2 O2 FeSO4 + S° + H2O (2) The rates of these reactions increase with temperature. However, at temperatures above the melting point of sulphur, 12°C, the presence of a surface active agent is necessary to prevent the occlusion of the sulphide particles by elemental sulphur and the consequent termination of the leach. The zinc that is dissolved according to reaction (1), after purification of the zinc sulphate solution, is recovered by electrowinning. The iron that is put into solution according to reaction (2) is further oxidized to the ferric state and subsequently, as the acidity decreases, precipitates as hematite or as complex basic sulphates. MINERALS AND METALLURGICAL PROCESSING Examples of this are shown below. 2FeSO4 + H2SO4 +1/2O2 - Fe2(SO4)3 + H2O (3) Fe2(SO4)3 + 6H2O - Fe2O3.3H2O + 3H2SO4 (4) 3Fe2(SO4)3 + 14H2O - 2(H3O)Fe3(SO4)2(OH)6 + 5H2SO4 (5) (hydronium jarosite) The conventional zinc process involves concentrate roasting to produce zinc oxide and sulphur dioxide. The zinc oxide is leached in spent electrolyte and the sulphur dioxide is converted to sulphuric acid. The pressure leaching process can, therefore, be used to replace conventional concentrate roasting, sulphuric acid manufacture, and atmospheric leaching with one unit operation. Integration of pressure leaching into the Kidd Creek flowsheet A block flowsheet of the Kidd Creek zinc plant, with the new pressure leach plant integrated, is shown in Fig. 1. The original plant, which was constructed in 1972, is based on standard electrolytic zinc plant technology. Concentrates are dead roasted to remove sulphur. Sulphur dioxide is treated to produce sulphuric acid. Calcine is leached in two stages using cell-house electrolyte. Iron is precipitated as jarosite and solutions are purified to remove copper, cobalt, nickel, and cadmium to provide feed for a partially mechanized cell house. Zinc is plated from solution, and the resulting cathode is melted, cast, and sold (Johnston, 1983). The integration of the pressure leaching plant into the main zinc plant is relatively simple. As shown in Fig. 1, a fraction of the zinc concentrate and spent electrolyte are fed to the pressure leach autoclave, while part of the calcine from the roaster is used as a neutralizing agent in the oxidation step along with. the jarosite leach solution. The main exit stream from the pressure leaching plant is the slurry discharged from the oxidation step, consisting of neutral zinc sulphate solution, unreacted calcine, and precipitated iron oxides. This slurry is transferred to the neutral leach step in the main zinc plant. The leach residue from the pressure leaching step, consisting of basic iron sulphate and elemental sulphur, is washed and impounded along with the jarosite residue produced in the main plant.

Jan 1, 1987

By B. J. Scheiner

The presence of organic materials in gold ores cyanidation. The presence of organic materials interferes with gold extraction by The carbon contained in the ore has been shown to adsorb gold cyanide complex from solution. Removal of the carbon content by roasting or chemical oxidation prior to cyanidation results in gold extractions of 85 to 95 pct. This paper by the Bureau of Mines, U.S. Department of the Interior, discusses how the mineralogy of the carbonaceous gold ores affects gold recovery by cyanidation. It also discusses the advantages and disadvantages of roasting and chemical treatment to render the ore amenable to cyanidation.

Jan 1, 1987

By J. Andrew Leach, Robert T. Tape, Thomas G. Harper

A practical approach to elope stability design of heap leaches up to 90 m (300 ft) high is presented based on recent experiences with heaps throughout the Western U.S. Shear strength parameters for foundations, ore and liner systems are considered, with particular attention given to frictional contacts between geomembranes and clay or geotextiles. Stability of both ore and containment dikes is discussed including the effects of seismicity, staged dike construction, progressive heap development and in-heap solution levels. Design criteria and methods of analyses are presented along with techniques for improving stability.

Jan 1, 1987

By Richard Crawshay, Duncan Hutchison

Continuous Mining Systems Limited have developed an efficient, high-capacity, in-line loading unit capable of handling shot rock in tunnel driveages at extraction rates up to 970 tonnes (1,000 tons) per hour. A smaller 408 tonnes (450 tons) per hour loader is also available These in-line loading units called "Osciloaders"® provide a continuous flow of material from the muck pile to an anciliary conveyance eliminating the cyclic or interrupted movement noramlly associated with gathering arm or bucket type loaders. The osillating lip fluidizes the material, reduces the penetration force required and facilitates and regulates the material flow onto the adjacent conveyor. The conveyor is wide and accommodates very large material with ease, transporting and elevating it to a height suitable for a waiting conveyance at the rear of the machine. The "Osciloader"® is currently being utilized for production mining by a major company in Sudbury, Ontario. Both truck and conveyor anciliary haulage are being utilized. The paper describes the development of the loader and how it may be applied in tunnelling applications.

Jan 1, 1987

By K. C. Vories, C. D. Elifrits, F. F. Haston

The required reclamation of land disturbed by surface coal mining often results in the creation of some oversteepened slopes that are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has shown that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations are summarized in this paper, and field results are shown.

Jan 1, 1987

By D. J. Torpy

With copper at its host depressed price in several years, producers are looking at every opportunity to cut costs in order to continue operating. Some of the measures that have been applied by different companies include reduction in manpower, high grading, and in some cases partial shutdowns. The most beneficial cost cutting measure implemented by Southern Peru Copper Corporation was to steepen the slope of the final pit limit from a conservative 37 degrees to an average of 48 degrees. By doing so, substantial cash outlays were saved. Southern Peru Copper Corporation (SPCC) operates two open pit copper mines and concentrators in the southern part of Peru, about 150 kilometers from the Chilean bordar. The Toquepala Mine went into production in 1960 and the Cuajone Mine in 1976. Both mines use shovel, truck and train operations. The trains, which haul ore to the crusher or waste to the dumps, are loaded either directly by shovels or by a transfer system. The Toquepala Concentrator treats an average of 43,000 tons per day and the Cuajone Concentrator an average of 55,000 tons per day. Concentrates are shipped via a 200 kilometer railroad to the port city of Ilo where the SPCC smelter is located. The annual production in the smelter from both mines is 290,000 tons of blister copper.

Jan 1, 1987

By P. Venkatasubramanian

The aerospace and nuclear industries have been applying systematic techniques for assessing the safety of complex technical systems for many years. These techniques such as fault tree analysis, failure mode, and effect analysis, etc., and more recently "expert systems," were developed to formally evaluate systems safety and to determine how hazards can he reduced. The application of formal methods such as expert systems has the potential for further reduction in both frequency and the consequences of mine accidents. This paper presents a general expert system model of diagnostic reasoning and describes its use as an inference method for analysis and problem identification for accidents due to the presence of an open cycle diesel-powered mine cars in underground coal mines.

Jan 1, 1987

By L. W. Saperstein, M. C. Radomsky, D. L. Passmore, J. D. Bennett

About 60 small surface coal mines in Pennsylvania participated in a program designed to improve safety performance in the workplace. The method involved the use of safety sampling and observation to assess the degree of safety exhibited by workplace behavior and conditions. Data were collected through the use of on-site safety instruments covering seven major occupational positions typical of small surface mines. Workplace events observed (acts and conditions) were assigned a hazard classification. Feedback was initiated to improve safety performance in areas failing to conform to appropriate safety standards. Results suggest that the variety of unsafe acts and conditions associated with the companies observed are extensive. Further, the experiences drawn from this pilot project have proven the need to pursue this behavioral approach. Future research should concentrate on subjecting the present approach to a strict experimental design involving randomly selected “poor risk” mines.

Jan 1, 1987

By George W. Poling

Designing optimal placer gold recovery plants requires a detailed knowledge of the size, shape and surface physical characteristics of the gold particles and the host alluvium in the pay gravel, sand or clay. Results of a recent pilot-scale study of the quantitative performance characteristics of riffled matted sluice systems are presented. For the appropriate non-coherent pay gravel-sand with medium-flat gold, simple sluices can recover gold at greater than 85% efficiency down to 100pm diameter. Alternatives to simple sluices are presented and discussed briefly.

Jan 1, 1987

By Alexander I. Feldman, Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

An extensive geotechnical monitoring program was used to assess ground and liner behavior, provide input to a Disputes Review Board, and verify design assumptions during construction of the Mt. Baker Ridge Highway Tunnel along I-90 in Seattle, Washington. The stacked-drift tunnel liner was constructed with twenty-four 2.9 m diameter concrete-filled drifts forming a semi-flexible compression ring, followed by excavation of the 19.4 m diameter soil core. Instrumentation data was used for monitoring hillside stability, liner deflections and loads, impacts on adjacent highway tunnels, for back analyzing soil properties, and for helping to limit construction-induced settlements to about 6 cm.

Jan 1, 1987

By Kevin R. Burns, William A. Depree, John J. Jansky

This paper presents some of the work associated with the reduction of employee exposure to diesel and blasting contaminants at an underground salt mine. The purpose of the paper is to outline the procedures recommended in resolving the problems associated with these contaminants. The first stage consists of a complete mine ventilation survey. The purpose of the survey is to identify any problems in the mine. The survey consists of air quality, air quality and ventilating pressure measurements taken throughout the mine. After completing the survey, the information is analyzed to identify problem areas and the possible causes. All available solutions to reduce the levels of contaminants are then explored and evaluated for feasibility. The PSU Mine Ventilation Simulator is then used to accurately simulate possible changes to the ventilation system. These ventilation projections are a useful tool to illustrate to the company and union personnel the possible benefits of various ventilation changes. This paper will illustrate the phases involved in making important and sometimes expensive ventilation decisions. Through the cooperative efforts of MSHA, company and union personnel, the levels of contaminants have been reduced by approximately 200 percent. As a result of these ventilation improvements, the company can now safely increase production approximately 25 percent.

Jan 1, 1987