Search Documents

By H. L. Ehrlich

Processes involving biological solubilization of metal values from ores, or removal of mineral constituents that interfere with metal value recovery from ores by abiological means, published mostly in the last 10 years, are reviewed. Many of them, though promising, have yet to be tested on a pilot scale or applied industrially.

Jan 1, 1987

By Michael J. Martinson, John R. Larsen, J. Warren Andrews

Measurements reported in the paper were recorded in an active Green River, Wyoming, trona mine, partly as a teaching exercise and partly to provide the mine in question with additional input data for its ventilation network program. Measurements were made: - in representative three-entry intake airways in room and pillar sub-mains; - between the lower portion of a vertical down-cast hoisting shaft and the start of an intake airway system established in a room and pillar main; - in a representative downcast section of a divided vertical shaft, and of the collar entrance loss at the top of the same compartment. Pressure differences were measured with manometers and trailing hoses, air flowrates with calibrated anemometers, and barometric pressures and wet-and dry-bulb temperatures were recorded for density determinations. Where possible, results are quoted as Atkinson friction factors, and relevant measurements are recorded in some detail to show the magnitude of fluctuations in observed pressure differences.

Jan 1, 1987

By Russell G. Slayback

Feasibility investigations for prospective gold mines too often neglect to consider ground water. Simple observations and tests during drilling exploration can provide useful data on probable water conditions. As the prospect becomes more serious, more detailed investigation of ground water and dewatering needs may be warranted. Ignoring ground-water conditions can lead to costly mistakes.

Jan 1, 1987

By Greg Struble

The Homestake Gold Mine is one of the deepest and most extensively developed hardrock mines in North America. The mine is divided into five divisions which produce a total of 1.7 million metric tons of ore per year. In the past, labor intensive mining methods such as open cut-and-fill, shrinkage, and timber stoping were utilized. In recent years there has been an extensive change to the more productive methods including Vertical Crater Retreat and Mechanized Cut-and-Fill. Also, the percentage of production from the lower divisions below the 4850 level is increasing while upper level reserves are beginning to decline. Combined, these factors have strained the ventilation resources to the limit. By early 1984 it became clear that future production trends would require a detailed study of future ventilation resources. By November of 1984 the Ventilation Department completed a study to project these future requirements. This paper will detail the first phase of a scheduled two phase upgrade: the installation of a new surface fan.

Jan 1, 1987

By A. E. Strakele, M. W. Springett, S. N. Watowich, W. F. Matlack, E. Yeomans, S. L. Manske, B. Yeomans

The Mesquite gold deposit is a large, low-grade "disseminated" ore body located in the Chocolate Mountains 65 km (40 miles) northeast of El Centro, CA. The deposit is tabular in geometry with a gentle southwest dip, concordant to a sequence of quartzofeldspathic to mafic gneisses. The host gneisses are amphibolite grade and intruded by synkinematic leucogranite and pegmatite. Reset potassium-argon (K-Ar) dates of 32 to 38 m.y. on mineral separates from gneiss in the ore body are suspected to reflect the age of mineralization. The hypo gene mineralization was introduced with siliceous breccias and -quartz veinlets and consisted of argentiferous native gold associated with minor pyrite and other base metal sulfides. Fluid inclusion study of gangue quartz indicates that the hydrothermal system contained a 225°C (437°F) boiling, 1 wt % NaCl equivalent solution with a small amount of CO2-A high degree of post-mineral faulting and fracture has resulted in deep oxidation and has obscured the original geometry and hypo gene mineralization of the ore body.

Jan 1, 1987

By C. E. Ekburg

Gold Quarry is a sediment-hosted, epithermal disseminated gold deposit located along the Carlin Trend. Gold, hosted by allochthonous Ordovician siltstones and cherts, is localized at the intersection of structures sympathetic to the major Good Hope and Gold Quarry faults. The magnitude of Gold Quarry was discovered in 1979 by surface exploration and by percussion holes drilled near the Maggie Creek orebody. Four years of development drilling delineated an open pit mineable gold deposit that contains 130 Mt (144 million st) of ore at an average 1.68 g/t (0.049 oz per st) of gold and includes a high-grade core of 46 Mt (51 million st) that average 2.64 g/t (0.077 oz per st) gold. Milling of the higher-grade portion began in 1985.

Jan 1, 1987

By Sun Guangzhong, Liang Jinhuo

Adverse geological condition is a major factor which makes construction difficulty in tunneling. But if it is predicted and tunnel support is made efficiently in time, the above difficulty can be reduced. It is necessary to develop one or several effective and economical geological methods for prediction of tunnel geology while expensive and time-consuming instruments are used. This paper reviews and proposes several geological methods for prediction of fault, seam, contact zone, and groundwater inrush. These methods have been proved to be effective and economical in tunneling practice in China.

Jan 1, 1987

By Munson R. McKinney, Bryan A. Slim

To date some 1,000 exploration targets (by way of adits, mine dumps, shafts, outcrops and unstoped mine areas) have so far been identified using an interactive data base system to query a digital data base comprising topographic, cadastral geological and mine components developed as a compilation of old plans, records, surveys and recently flown aerial photography. The exploration targets are intended for early follow-up as part of a 1987 exploration programme to investigate the reserve potential of the former producing property located in southern Utah. Of further interest is the unscrambling of old mine plans to provide drill targets for investigation of unstoped reserves with one target being a possible 800,000 tons in part of the lower workings. The project site encompasses about 3,200 acres of mainly patented lode claims covering most of the claims and mines of the Gold Mountain mining district formed in 1889. Turn of the century mining saw several mines operating whose total production was at least 143,000 oz. gold and 460,000 oz. silver from steeply dipping veins up to 20 ft. or more in thickness.

Jan 1, 1987

By M. F. Vancas

The San Manuel oxide ore reserve ranges in depth from being exposed on the surface to lying 1000 ft. beneath a conglomerate layer all of which is confined in the subsidence zone of an active sulfide block caving operation. Present day recovery of the oxide copper values is either by open pit mining-dump leaching, or in-situ leaching of the oxide ore using dilute sulfuric acid solutions and solvent extraction/electrowinning processing of the pregnant leach solutions. Future plans are for continuation of leaching with expansion of reserves and increased processing rates. The state of the mining industry and copper in particular has not been good for a number of years. All of the producers that are still operating have made major adjustments in order to remain competitive. Magma Copper Co. is no exception.

Jan 1, 1987

By Howard J. Brown

The Lucerne Valley limestone mining district is in the San Bernardino Mountains, one of the major ranges in the Transverse Range Province of southern California. Several large limestone mining operations are present along the north range front in Lucerne Valley, and the area is one of the premier limestone mining districts in the country. Resources are contained in Paleozoic carbonate rocks that are part of a thick late Precambrian and Paleozoic sequence that uncomformably overlies crystalline basement. The district has been affected by multiple episodes of metamorphism and deformation, as well as by a complex sequence of late Cenozoic structural events. Detailed studies, however, have demonstrated that these rocks can be divided into formations correlatable with late Precambrian to Permian strata of the Cordilleran miogeocline. The district is the leading producer of white, high-purity calcium-carbonate products in western North America. Pluess-Staufer (California) Inc. mines and processes high-purity white limestone from extensive deposits, and is one of the largest producers of high-quality limestone fillers and extenders in the western United States. Major factors influencing the genesis of economic carbonate deposits in the district include depositional environment, post-depositional processes such as diagenesis, dolomitization and/or silicification, regional and/or contact metamorphism and associated intrusive activity, faulting, folding, uplift and erosion, and preservation from erosion. Regional geologic studies, detailed geologic mapping, intimate knowledge of stratigraphy, and recognition of complex structural relationships have proven to be invaluable tools in the discovery of high quality calcium carbonate deposits in the district.

Jan 1, 1987

By C. D. Wittreich

The University of Idaho, Department of Metallurgical and Mining Engineering, through the Generic Mineral Technology Center, has been engaged in mine design research at the Lucky Friday Mine, Mullan, Idaho. The purpose of the research is to develop and implement the longwall underhand cut-and-fill mining method for conditions at the Mine. The longwall underhand cut-and-fill mining method involves backfilling mined stopes with a compacted tailings-cement mix. After the backfill has been allowed to cure, mining is resumed from underneath. Horizontal stresses in the Lucky Friday Mine are exceptionally high and rock bursts are a common problem. Beus and Chan (1980) have reported a 2:1 horizontal to vertical stress ratio at the mine with a 65-MPa (9,500-psi) maximum horizontal stress at the 1,295-m (4,250-ft) level. Using this mining method under these stress conditions, it is desirable to have a backfill material that has sufficient strength to safely carry the high horizontal wall loads while minimizing external steel supports.

Jan 1, 1987

By James R. Miller

Recent experience over extensive areas of the Basin and Range Province has demonstrated the importance of the basin's (valley's) geology and geomorphology in locating large quantities of good-quality aggregate. First, a geologic map depicting basic geomorphic-geologic units in a valley is made in the office from aerial photography. Next, derivative maps are made from geologic maps and field-derived information such as parent rock type, source area and depositional environment, relationship to adjacent deposits, and Quaternary geologic history. Studying the derivative maps leads to selection of test sites for potential deposits of high-quality aggregates. Subsequent field studies provide more detailed information about geologic processes and samples for laboratory testing. Combining all information allows the characterization of aggregate potential of very large areas. Favorable areas can be further tested. This phased approach has proven to be cost effective. The methodology used in mapping and characterizing basinfill deposits is applicable over much of the western United States. Map units were developed by focusing on the predominate geomorphic process, grain size, cementation, and relative age. The resulting functional map units are of use to engineers and planners. This study led to many conclusions, including the fact that the best quality basinfill aggregates are found in selected alluvial fan deposits and Pleistocene lakeshore deposits. The best quality aggregates are derived from Paleozoic carbonate and quartzitic parent materials that can also provide high-quality crushed-rock aggregates.

Jan 1, 1987

By Roberto Zaragoza

Historically, the control of flotation operations has been viewed by many as an art. Only recently has process measurement and control come to be viewed not as an ?art? but as a very complex and productive science. In recent years, process control applications to flotation plants have been established and already some gains have been reported for several industrial operations using individual stabilizing control loops including level, pulp flow, pulp density, reagent addition rate and pH (Paakinen, 1979; Hales, 1985). The use of process control computers combined with on-line x-ray florescence (XRF) in industrial flotation circuits has made the application of more sophisticated control techniques feasible in the mineral recovery process. In spite of the availability of reliable instrumentation in modern flotation plants, satisfactory control strategies are difficult to develop and implement. Extremely important factors such as changes in ore type, liberation characteristics, flotability, degree of oxidation on particle surfaces, and specific gravity constitute unmeasured disturbances to the process. Most current control systems cannot adapt specifically to such disturbances.

Jan 1, 1987

By Stephen J. Reynolds

Arizona's geologic history is complex, resulting in a diversity of rock types and earth materials, including those of commercial interest. Regional variations in geologic history gave rise to three geologic provinces and an inequitable distribution of both metallic and nonmetallic mineral wealth. The Colorado Plateau is largely composed of flat-lying Paleozoic and Mesozoic sedimentary rocks and late Cenozoic volcanic fields and sedimentary deposits. Associated resources include gypsum, halite, sylvite, clays, specialty sand, flagstone, volcanic products, and aggregate. The adjacent Transition Zone features a large expanse of Proterozoic rocks, economically important Devonian and Mississippian carbonate rocks, and Tertiary volcanic and sedimentary materials. Nonmetallic resources in this province include facing and dimension stone, aggregate, decomposed granite, chrysotile asbestos, gypsum, clay, barite, fluorspar, zeolites, and limestone used for lime, cement, and railroad ballast. The Basin and Range Province has the most complex geologic history and, therefore, the most diverse assemblage of industrial mineral occurrences. These include halite, gypsum, clay, aggregate, decomposed granite, diatomite, zeolites, perlite, pumice, kyanite, limestone, marble, stone, and others. In addition, young stream deposits yield vast quantities of sand and gravel, Arizona's most economically important nonmetallic mineral commodity.

Jan 1, 1987

By S. R. Hutchins

Several refractory sulfide and carbonaceous gold ores were examined to determine whether microbial pretreatment could be used to enhance gold recovery. Test samples were biologically leached using unique, thermophilic microorganisms to solubilize iron sulfide minerals. Gold recovery from sulfide ores and concentrates was enhanced following pretreatment with the thermophiles; responses varied widely for the individual materials. Although bioleaching had little effect on the preg robbing characteristics of the carbonaceous gold ores, cyanidation of the bioleached residues yielded higher gold recoveries than cyanidation of the native ore. By combining bioleaching with abiotic processes designed to inhibit preg robbing, gold recoveries of 83-98% were obtained from carbonaceous ores yielding 10-50% gold recovery by direct cyanidation.

Jan 1, 1987

By K. E. Burgher

Since World War II, the need for the use of explosives in construction, mining, and quarrying near congested urban areas has increased dramatically. Often times a coal mine, once isolated from a city, finds itself surrounded by residential and commercial structures. The United States Bureau of Mines and others have researched blast design to a point where ground vibration and airblast damage can be avoided. A problem still exists, however. It is the fact that people often react to only the loud noise associated with a blast although it may not cause damage. Most often it is the concussion of a blast, less than 20 hertz and inaudible, that produces damage. Public fear from the "startle" and "fright" of loud blast noise greater than 20 hertz leads to the complaints which are generally unfounded. See Thackray, Touchstone, and Baily (1975) for a further discussion of the startle effects of loud sudden noises. When blasts are designed in accordance with U.S.B.M. specifications, management generally has little to worry about with respect to damage claims. Complaints, however, still arise when the noise is accentuated from the blast. It is meteorological conditions which dictate how the sound levels will propagate. Some mines use small pilot test shots (generally one-two lbs) to determine when atmospheric conditions favor sound travel.

Jan 1, 1987

By George Verley

A new and important task in assisting developing countries is the transfer of microcomputer technology applied to mineral exploration and mining. With this objective in mind, three micro- computers have been introduced in Niger and a training program has been put into place. The core of the program consists of two seminars in Niamey, Niger, after which the attendants will be able to operate a microcomputer and use a small library of application software.

Jan 1, 1987

By G. B. Misra

Heat transfer in partially wet mine airways has been the subject of study for quite some time. Of the available models some are quite empirical while some involve highly complicated computation. Models developed by Amano, Mizuta and Hiramatsu and Banerjee and Chernyak as well as that modified by Misra were evaluated for prediction of the rise in temperature and humidity (mixing ratio ) of partially wet mine airways at four different levels in the Mosaboni Mine of Hindustan Copper Ltd. Measurements of barometric pressure, virgin-rock temperature and changes in dry- and wet-bulb temperatures along a certain length of airway were made. The rise in dry-bulb temperature and mixing ratio of air over the sections were calculated using the three models. The study reveals that calculated values of temperature and moisture content agree within possible rage of experimental error with all the three models in case of three levels with low wetness factor, but the agreement was poor for the relatively more wet airway on the 30th level. Errors in the estimation of fw to the tune of 0.025 can lead to fair error up to 0.94 K in the estimated temperature while alternative ways of estimating the heat transfer coefficient [] can introduce errors up to 1.45 K.

Jan 1, 1987

By Jeffery L. Kohler

The characteristics of mine airstreams, such as their magnitude in the time and frequency domain and their spatial distribution, as defined by isovels, must be considered when making a measurement. The possibility for erroneous measurements is greatly increased when fixed- point sensors for mine monitoring systems are used. However, an a priori understanding of the airstream characteristics can be used to reduce the possibility of erroneous readings. This paper describes the problem, presents data to illustrate the nature of the problem, and provides recommendations for alleviating the problem.

Jan 1, 1987

By Ruiren Jin

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II)-activated sphalerite exhibits a high flotability so that satisfied separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by IR; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitute and polymerization of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1987