Search Documents

By Tracy E. Chantson, Brian R. Green, Kenneth G. Ashurst

Work that has culminated in the manufacture and testing of a old-selective resin on a pilot-plant scale is dcscribed. Following a brief discussion about the nature of commercially available resins which identifies them as poor candidates for a gold extraction application, the improved properties of the new type of resin are illustrated using results from comparative loading tests. Further results from continuous countercurrent extractions using synthetic leach liquors and elution work using thiourea as the eluant demonstrate the superiority of the new resin over commercial resins and hence, its potential for use in a resin-in-pulp process for gold.

Jan 1, 1989

By N. Arbiter

During the first four decades of flotation practice, close to 200 machine designs were patented, although only about a score were ever used commercially. By the end of that period, the rigors of use had resulted in obsolescence of most pneumatic cells, with a few mechanical cells dominating the field. After World War II, newer designs began to appear but most were modifications in varying degrees of older designs with special features added. Of the dozen or so most recent developments, almost all are pneumatic, relying on compressed air instead of impellers for motive power, although in several cases pumps supplement compressors. Table 1 lists a few of the more fully documented new cells, with their significant characteristics, along with similar characteristics of a widely used mechanical cell. New designs in general are emphasizing: bubble size control; in several cases, methods for delivering feed directly to the froth; methods for introducing and dispersing air through nozzles, eductors, packed beds, or permeable walls; and variable cell volumes, relative to capacities, ranging from very small, with less than a second of retention time, to the largest, with retention times of over 20 min. An important question is the extent to which any of the newer designs are based on locating weaknesses in current mechanical cell designs and then using these as a starting point for innovations. In the present study, the key subprocesses which must take place in a cell are outlined; mechanical cells are analyzed to establish where weaknesses may exist; and then alternative subprocesses are considered which could effect improvements. COMPONENTS FOR CELL DESIGN It is assumed that mineral surface chemistry has been modified as necessary to provide optimum potential floatability. While the cell process may affect this to a degree, cell design is primarily concerned with actualizing the existing potential floatability. The cell design problem is to provide more effectively for the following: 1) Dispersion of air to obtain an optimum bubble size distribution at an optimum ratio of air volume to feed volume. 2) A hydraulic environment which permits most effective contact of potentially floatable particles with bubbles: [Table I - Cell Comparisons* Cell Type Mechanical Column Deister Miller ASH No. of units Multiple Single Single Single Retention time min.10/20 17/27 3.8 ca. is Capacities mt/m3s 0.022/0.066 0.066/0.20 0.11 10.4 st/ft3d 1/3 0.3//0.9 m5.0 469 Air hold-up % 15/20 20 n.a. 50/80 Air escape velocity m/s 0.015/0.0200.020/0.025 n.a. n.a. ft/m 3/4 4/5 n.a. n.a. * References: Mechanical (Harris, 1976,1985), (Bassarear, 1985); Column (Travis, et al. 1987); Deister (Zipperian and Christophersen, 1985); ASH (Air-Sparged Hydrocyclone) (Miller 1989).]

Jan 1, 1989

By B. W. Lawrence

Shaft alignment requirements are consistently met using conventional shaft sinking methods. Little attention has been given to achieving similar alignment accuracies using rotary drilled shaft methods. Alignment of these shafts is difficult to control and guarantee. Bare shafts and shafts that use drum hoisting systems can accept some deviation. However, combining drilled shafts with Koepe hoist installations presents new accuracy requirements for drilled shafts. This paper describes the importance of verticality with practical examples, and discusses various methods of measuring verticality and their respective limitations.

Jan 1, 1989

By LeEtta M. Shaffner, John R. Marks

The Homestake Gold Mine in Lead, South Dakota, commenced operations in 1876. As is the case with old, deep, continuously developing mines, a ventilation improvement is periodically required to maintain acceptable underground environmental conditions. Recent historical improvements at Homestake include a 5.2m diameter air shaft driven in the 1960's and a 2.1 MWR (580 ton) chilled water plant installed in 1978. By 1983, it became apparent that yet another ventilation upgrade would be needed to keep pace with accelerated development in the deepest mining sections. A study was therefore undertaken to project ventilation requirements for the next ten years and to select the method(s) most suitable to meet those requirements. The study called for a two-phase approach in which air flow and air conditioning were carefully balanced. Phase I, the installation of a new 2240 kW surface fan and several underground circuit changes, was completed in 1986. This paper describes Phase 11: the planning, design, installation and initial performance of the air-conditioning portion of the upgrade.

Jan 1, 1989

By Stanislaw Wasilewski, Zdzislaw Krzystanek, Boleslaw Firganek

The experimental system for mine venti1ation control in Staszic colliery has two - level structure. In the lower - measuring 1evel the existing computer - based early fire detection system has been used completed with a number of additional sensors needed for ventilation parameters monitoring. The higher 1evel is a secondary computer equipped with a suitab1e dedicated software performing data processing according to the control a1gorithm. Direct control of air flow in a selected mine district is performed by means of a remotely controlled automatic regulator. Apart from functional tests of the system and its elements some research work has been carrying out in the colliery based on observations of transient effects caused by changes in air flow distribution.

Jan 1, 1989

By Terence G. McCusker

Precast concrete segmental tunnel linings have been used since at least 1903. More serious attention was devoted to them in England during the World War II steel shortage and they have become increasingly common since that time. They are now coming into common use in the United States, especially as primary linings for soft ground tunnels and for rock tunnels in poor ground, although they have also been used as final lining, especially in rock tunnels. The developmental logic, design considerations, and current practices are examined. Particular attention is given to unbolted linings, with and without secondary linings. Probable future developments are considered.

Jan 1, 1989

By M. R. Peterson, C. R. Ferguson, T. H. Jeffers

The ability of microorganisms such as yeast, bacteria, and various aquatic flora to sorb metals from dilute aqueous solutions is well documented. Although microorganisms have significant potential in decontaminating waste waters, techniques and equipment suitable for bioassisted decontamination are limited. The Bureau of Mines has investigated the use of microorganisms immobilized in porous polysulfone beads for extracting toxic and heavy metals from dilute waste streams. The minus 8- plus 12-mesh beads were fabricated from high-density poly- sulfone dissolved in dimethylformamide (DMF). Dried, thermally killed yeast, algae, duckweed, xanthan gum, and alginates were blended into the polysulfone-DMF, and spherical beads were formed by injecting the mixture into water. Microscopic analysis revealed microorganisms immobilized within the bead pores. The beads had excellent handling characteristics and were tested in stirred reactors, fixed bed columns, and fluidized bed columns for their ability to remove metal contaminants from several waste waters. The effluents resulting from these waste waters met or exceeded the National Drinking Water Standards for cadmium, copper, manganese, and zinc. Other heavy metal contaminants readily sorbed by the beads included arsenic and mercury. Elution of metal values from the beads was accomplished using dilute nitric acid or sodium carbonate.

Jan 1, 1989

By H. A. Kortmann

Blast furnace operators have been steadily increasing their quality requirements on burden material. These requirements include a high reduction rate of the ore burden as well as good strength at the beginning and during the whole blast furnace operation. Special requirements are made on the softening and melting behavior which ensures an optimal formation of the cohesive zone in the blast furnace. On the whole, the self-fluxed and olivine-based pellets meet these higher requirements due to their chemical composition, especially in the pure pellet operation. In the mixed sinter/pellet operation partly-fluxed and acid iron ore pellets can be appropriately used. The paper describes the demands on, and characteristics of, different kinds of pellets used in the Federal Republic of Germany.

Jan 1, 1989

By H. Zhu

Qualitative and interpretative information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system pro-vides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data.

Jan 1, 1989

By James R. Arnold

Gold Fields Mining Corporation started processing ore from it's Chimney Creek operation in northern Nevada in November, 1987. Since that time production has averaged about 200,000 ounces per year from the milling and dump leaching circuits combined. The events that led up to commissioning of the plant started in January of 1985 when the Gold Fields exploration team drilled their first hole in an area now known as Discovery Hill. The major orebody was located later in the year in what is currently the major focus of activity, the North Pit. Subsequent drilling since plant startup has found another 14 million tons of ore two miles south of the original orebody. This South Pit orebody is currently being stripped and metallurgical testing is underway. Engineering Engineering on the Chimney Creek plant started in earnest in May, 1986. Davy McKee Corporation from San Ramon, California, did both the engineering and the construction management. Before engineering began the entire senior staff of the Plant Department was hired and assigned to the project. Senior staff included the Plant Superintendent, Plant General Foreman, Maintenance General Foreman and Chief Metallurgist. Gold Fields does not employ an internal central engineering staff to design their plants. We feel that the people who design the plant should be the ones who will be required to run it once it has been commissioned. This philosophy affords a continuous accountability from start of design through commissioning and operations. All four of the senior staff spent the most critical phase of the engineering stage at Davy McKee, so the plant is truly a reflection of all four disciplines. In bringing on the Maintenance General Foreman from the start, there was a focus placed on ease of maintaining the plant. Another philosophy that was adopted from the start was that the plant be easy to work in and maintain for both operators and maintenance personnel. Numerous design criteria were given to Davy McKee to ensure this. For example, we required that every piece of equipment could be reached easily with a crane or fork lift. All conveyors were required to have walkways on both sides for ease of maintenance and a minimum of 30 inches of clearance under them for ease of cleanup. Visibility for operators was considered very important and the control rooms and general plant layout were designed with this in mind. A list of about 100 general rules were given to Davy McKee during the early layout meetings and these were held as the general design criteria throughout engineering and construction. While engineering was progressing in San Ramon, California, dump leach test work was being done at the site. Three 6 foot diameter fiberglass columns were constructed and filled to a 20 foot height with low grade ore. Leaching characteristics were determined and the dump leach design was based on information collected from these columns. Construction The major contractors on the project were The Industrial Company for the bulk of the piping and structural, EMKO on the electrical/ instrumentation and Hunewill for most of the earth work and leach pad construction. All plant operating and maintenance personnel were employed eight weeks before startup for intensive training. Instructors were Gold Fields personnel, including foremen, and Davy McKee engineers. On occasion, selected suppliers representatives were brought in to discuss major pieces of equipment. Project completion was targeted for January, 1988 at a projected cost of 78.9 million dollars. Actual startup was about 1 1/2 months ahead of schedule and slightly under budget. Full design capacity was achieved the first full month of operation. Crushing Run of mine ore is delivered to the crusher and dumped into a 90 ton hopper which is topped with a 30" X 30" opening stationary grizzly. Ore is fed to a 50" X 60" Telsmith jaw crusher with a 5' wide apron feeder. The closed size setting of the

Jan 1, 1989

By F. L. Wilke

The prototype of an expert system, designed to assist layout planning of face operations, is presented. By specific combination of knowledge-based and conventional EDP techniques it has been possible to extend the known Kepner-Tregoe method up to the determination of mature layout solutions in difficult planning cases. It has been proven that the presented strategy - which can be applied to any kind of problem with similar structure - is apt to provide efficient EDP support for handling complex mining problems. Such support goes far beyond the purely numeric evaluation of envisaged alternatives.

Jan 1, 1989

By Pentti Kallio

From the aspect of economic feasibility of mining, ineffective use of expensive mechanization investments is becoming a problem. In many cases, the machinery is in operation only 50 - 60 % of the total working time. The lost time when the machines are idle means a considerable over-investment in machines. The lost time, with LHD equipment in particular, accumulates from the following constituents: - the needs of the person operating the machine trips to the work site, lunch, coffee and other breaks, want for comfort, etc. - deficiencies in the monitoring and control systems for machine operation waiting periods at loading and unloading stations, unnecessary and erroneous actions, inefficient work, etc. - deficiencies in the machine condition monitoring system , and inefficient service and maintenance work The data transfer and computer technology of today provides means for resolving problems in several areas - including the area of underground loading operations. In the paper those areas of automation and data handling are considered which make possible an improvement in the usage and monitoring of LHD equipment. These fields are: remote control of equipment, use of TV cameras and monitors in remote control, locating equipment and data transfer down the mine, measurement of the load and the data storing system, systems for following the condition of the equipment, unmanned operation of equipment.

Jan 1, 1989

By Siegfried Zell

Preface Pipe heading is a customary and proven technology for the underground installation of all types of piping. In over 90 % of all cases, straight pipe sections are used between shaft constructions since, e.g. this follows roadways or it is necessary from the operational aspect due to pipe control methods, e.g. to use a remote control pipe sensor or comparable control devices within sight from shaft to shaft. Frequently, a straight pipeline is impossible, and is replaced by a more or less spatial alignment due to surface conditions, structures in the ground or foundations. This situation applied for the construction of the Nebensammler Neuland (intercepting sewer) in Hamburg-Neuland for sections IV and V. The following paper is not intended as a description of the complete project. It deals mainly with the special features of this pipe heading, with what I believe to be its somewhat unusual route. The task The building authority design issued by the Main Department for Urban Sewerage of the Free and Hanseatic City of Hamburg consisted of the construction of the collector by a pipe heading using NW 1300 pipes in 2 heading sections. One short straight and one long

Jan 1, 1989

By Thomas J. Lien

AMAX Coal Company has constructed the first commercial demonstration sub-bituminous coal dryer at its Belle Ayr Mine south of Gillette, Wyoming. This 215 ton per hour facility is projected to produce 165 tons per hour of dried coal at 10 percent moisture and 10,800 Btulpound (6,000 KCIkg). Approximately 43 tons per hour of water will be removed from the coal and seven tons per hour of coal burned as fuel.

Jan 1, 1989

By Robert A. Jankowski, Charles A. Babbitt, Natesa I. Jayaraman

Today, approximately 31% of underground coal mining operations have designated occupations or areas with more stringent (below 2.0 mg/m3) respirable dust standards in place. Many U.S. coal mines have been able to maintain compliance with very low dust levels, and the Bureau of Mines, in an effort to identify those factors contributing to low dust levels, completed a survey of twelve continuous miner sections which were able to maintain their dust levels at or below 0.5 mg/m3. The quantity and quality of face ventilation appeared to be the most important factor in controlling dust exposure. The results directed Bureau research towards identifying improved face ventilation techniques for reducing quartz dust levels on continuous mining operations. This research has involved the evaluation of a half-curtain face ventilation technique which reduces the cross-sectional area of the entry, thus increasing the air velocity over the operator. The Bureau has also conducted extensive laboratory studies to compare tubing versus brattice, including an evaluation of both systems in a crosscut turn. In an effort to improve ventilation and reduce dust exposures of roof bolter operators working downwind of the continuous mining machine, the Bureau has evaluated two novel face ventilation systems. The first system consists of a fan discharge tubing technique which routes dusty air away from the return entry being bolted. In a technique similar to the fan/tubing concept, exhaust air from the upwind continuous miner face can be scrubbed using a dust collector to capture a portion of the dusty air, clean it, and supply it to the bolter operators as a split of clean intake air. A better understanding of face ventilation techniques should lead to solutions to the problem of more stringent dust standards due to quartz.

Jan 1, 1989

By J. K. Szymanski, Val Srajer

In this decade mining companies in western Canada have searched for reliable and inexpensive ways to improve mine productivity. Truck dispatching systems, equipment vital sign monitoring and sensing, vehicle guidance systems, have all been considered. In this paper the off -highway vehicle monitoring systems used or planned to be installed at surface coal mines in western Canada are described. The monitoring systems are divided according to their function and application; installation and testing procedures are described, as well as the economic benefits to the mining operation.

Jan 1, 1989

By Stephen J. Klein, Fernando Orduz, Randall J. Essex

INTRODUCTION The Keystone Tunnel project consists of widening an existing 7.3 m-wide (24 ft) highway tunnel to a width of 13.7 m (45 ft) to provide a three-lane, two-directional highway tunnel. The 13.7 m-wide tunnel was excavated in a staged drill-and-blast sequence through foliated schist, and was supported using pattern rock reinforcement and shotcrete. Notable project features are: the low vertical cover over the tunnel is less than the span of the opening; the project is the second instance where the Federal Highway Administration (FHWA) has accepted rock reinforcement as a permanent support element; and the project is the first instance where the FHWA is accepting shotcrete as the final interior surface of the tunnel. This paper covers the design and construction phases of the project. PROJECT DESCRIPTION The South Dakota Department of Transportation (SDDOT) retained Woodward-Clyde Consultants (WCC) to evaluate the feasibility, prepare construction plans and specifications, and provide construction management services for the widening of the Keystone Tunnel. The tunnel is located in the Black Hills National Forest area of South Dakota near the southwest corner of the state. The Keystone Tunnel is on U.S. Highway 16A, about 0.8 km (1/2 mile) north of Keystone which is approximately 32 km (20 miles) south of Rapid City (Figure 1). Highway 16A serves as an important transportation link between Rapid City and the Mount Rushmore National Monument which is located about 2 miles west of Keystone. The road through the tunnel consisted of two lanes about 7.3 m (24 ft) wide, and is being widened [ ]

Jan 1, 1989

By Wayne Stange

Due to the availability of user-friendly microcomputer based packages, the use of simulation is increasing.. Users have however encountered problems inherent to the structure of sequential-modular simulators. These are the difficulties associated with estimating parameters for arbitrary' models and the solution of design and optimization problems. The implementation of an optimization routine in the simulator MicroSim has facilitated the solution of such problems. The literature indicates that more efficient numerical techniques for solving optimization problems than those presently used in MicroSim are available. These techniques, together with user-interfaces which allow such problems to be specified easily by users, will result in the development of simulators much more powerful than existing ones.

Jan 1, 1989

By Gerhard Sauer, Heimo Gold

The main advantage of the New Austrian Tunneling Method over conventional drill and blast techniques, TBMs and shields is its outstanding flexibility. Many different support concepts help to cope with all but the most adverse conditions. A considerable variety of unique additional support measurements provide a functional tool when dealing with particularly difficult conditions or restricting requirements. The resulting adaptability of NATM with respect to geometric and geologic changes is a cornerstone to providing an economic design and to a safe and unhindered execution of the tunnel work. To take best advantage of this flexibility and to emphasize its cost-saving capacity, NATM explicitly extends the design period into the construction phase. In accordance with corresponding ground classes or other anticipated conditions, a number of basic support categories and an array of additional support measurements are established during the actual design phase. The decision for applying a particular support category at a specific location and for necessary additions to the given support scheme, however, is regularly made on site after each advance, and is determined by the key persons involved in the construction. Contract documents must reflect this approach to facilitate the execution of the work and to curtail construction costs. Biased distributions of risks, however, can adversely effect the envisioned benefits. Consequently, the respective responsibilities of engineer, contractor, and client need to be redefined.

Jan 1, 1989

By John A. Herbst, K. Rajamani

Process improvement is probably the most widespread objective of mineral process plant operators in the late 1980's. An important part of such improvements is dynamic optimization which involves reacting to inevitable plant disturbances in such a way that productivity is maximized at every instant of time. This paper describes the way in which mathematical models can be and have been used in dynamic optimization. Both off-line and on-line model applications are described.

Jan 1, 1989