Search Documents

By C. J. Pritchard

As productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity, a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The tailgate development continuous miner section has been since transformed from a low productivity part-time function to a high productivity development/retreat panel and is available for long term mine development duties also.

Jan 1, 1989

By R. A. Paul

WIDCO, operator of the Centralia Coal Hine, chose dredging, a method not commonly used for overburden removal, as the fastest, safest, and most economical method for mining through an alluvial filled valley. Now that the work has been completed, how did the cost and schedule compare with the original estimates? What would we do different next time in preparing for a dredging contractor? What are the potential pitfalls working with a dredging contractor? Would we do it again? When should dredging be considered as an overburden removal option?

Jan 1, 1989

By Jörg Weidemann, Peter W. Kuchar, Paul Burgwinkel

The West German Ruhrkohle AG and the engineering company BEDIA have developed an emission control system for diesel engines that is suitable for use in underground coal mining, consisting of a granular catalytic converter and a dry cooling system. Its first ever application was to a diesel mining locomotive. In the catalytic converter the exhaust gases pass over porous, platinum-covered ceramic balls in a double tube, oxidizing CO to CO2. Simultaneously, soot particles in the gases are subjected to afterburning. Laboratory tests carried out by BEDIA and at Aachen University of Technology showed that there was a reduction of over 80% in the CO content of the exhaust gases and over 30% in soot emission. The dry cooling system fulfills all the requirements demanded of exhaust cooling underground and does not have the disadvantages of conventional systems. It needs little maintenance, and it is light and compact. The most important components are a waterjacketed exhaust manifold, a tube and shell heat exchanger, a new type of flame arrestor in a stacked crimped ribbon design and a Venturi diluter. The system has its own thermostatically-controlled cooling circuit to keep the exhaust temperature between 120° C and 150° C, thus effectively preventing the tubes becoming blocked up.

Jan 1, 1989

By E. P. Gustafson

Demand by precious metals explorationists for cost effective means to target subsurface geologic structures worthy of evaluation by means of drilling has led to the use of the predictor-correlator technique. To locate polarizable targets, the predictor-a localized inhomogeneity in electrical properties-is placed at various locations in the computer-simulated subsurface region, and correlated with the potential distribution observed in the field. The correlation coefficient obtained is assigned to the subsurface location. IP targets are extracted by calculating a second correlation section based on higher-frequency illumination and subtracting it from the first. The locations of correlation difference correspond to the locations of polarizable mineralization.

Jan 1, 1989

By T. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, ship-lap, etc. to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1989

By Boris M. Vorobjev

The paper in question discusses a wide range of topics related to computerized coal mine monitoring systems starting with the history of development and application of computerized monitoring coal mine systems and finishing with modern trends in the design and updating of such systems. The paper focuses exclusively on methodological and technical aspects of computer-based coal mine monitoring systems and their applicability in both surface and underground coal mining operations.

Jan 1, 1989

By Peter N. Calder, J. L. Workman

There are many opportunities for computers to assist in dragline mine planning. Three important areas particularly lend themselves to computer assisted study. These are overall mine design and planning, the computation and display of range diagrams and the calculation of production and production variability. The computation of range diagrams is of particular interest because of the importance of matching the dragline and site geometries. This paper examines the uses of range diagrams in dragline mining and illustrates the application of computer techniques to the computation using one such program as an example. The use of computer generated range diagrams for machine selection, pit design and in parameter analysis is discussed. Directions for further development are also provided. There is a great deal that can be done to additionally enhance the ability to provide accurate designs for the dragline operation. One area that needs special attention is the dumping of overburden around access ramps into the pit. This situation is one of the most difficult dumping sequences and affects machine selection and pit operation. It is also suggested that programs that simulate the production schedule of the drag-line would be useful. It is concluded that large overall mine planning programs are very important in dragline mining. However, smaller programs designed for a specific, task are also important tools in many cases. These are easy to learn and use, well adapted to the PC environment and provide useful information, both for design and for daily planning.

Jan 1, 1989

By Meliton M. Garcia, Satya Harpalani

This paper discusses the results of an investigation carried out in an underground mine to characterize the volatile by-products adsorbed on airborne particulates following the detonation of four common explosives including ANFO. The primary objective of this study was to determine if any organic amine compounds, particularly nitrosamines, and any polycyclic aromatic hydrocarbons were produced and trapped in the dust that a miner might inhale during the workday. The production of these substances is of great concern because of their suspected carcinogenic nature. The results of the study indicated that a large variety of the by-products are adsorbed on the particulates generated, and thus remain airborne following the detonation of explosives. The major by-products retained by the dust were bis(2-ethylhexyl) phthalate, and aliphatic hydrocarbons with carbon chains ranging from C12 to C28. One explosive, a water gel, produced the polycyclic aromatic compound, trimethylnaphthalene. No nitrosamine compounds were detected.

Jan 1, 1989

By Frank W. Pereira

The Montana Talc ore body was discovered in 1983 in Montana's Gravelly Range, about 40 km (25 miles) south of Ennis. Initial drilling indicated a 910-kt (1-million st) ore body of high purity talc. Preliminary analyses on ore cuttings included chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. Results indicated it was similar to talc currently being marketed from Montana and it would probably have good commercial value. Based on the positive test results, a test pit was made and a 180-t (200-st) sample of ore was mined. A portion of the ore was ground to various particle sizes and evaluated to determine its strengths, weaknesses, and other characteristics. The deposit is located close to the Cyprus Yellowstone deposit. It was therefore believed that Montana Talc ore may possess many of the same characteristics. Testing and analyses showed the talc to have a high purity and an extremely large surface area, even for Montanatype tales. The ore was also situated in a massive deposit, indicating low cost mining. While the lab analyses were encouraging, the true evidence would be obtained from commercial tests in the marketplace. About 91 t (100 st) of ore were ground to product specifications for pitch control, paint filler, and plastics filler. Consumers were contacted and requested to evaluate the sample talc products. A major trial for the talc as a pitch control agent was arranged at a Northeast paper mill. The trial indicated the new Montana Talc product performed as well or better than the current standard in the industry. In fact, due to a minor modification in the compaction process to make the transport of the talc easier, the product had substantially less dust than the currently used product. The operating people at the paper mill requested that management purchase this talc. Trials were also run at paint plants for use as a pigment filler. And the talc was fabricated into a number of plastics compounds. The initial product tests were largely positive and provided encouragement to proceed with the project. Different grinding mills were used and their performance evaluated. Significant data were generated by the custom grinders. They indicated how the Montana Talc ore ground and the particle size distributions produced at different grinding settings. Encouraged by the positive marketing tests, a prefeasibility study was commissioned. A talc grinding plant and mine plans were designed and capital and operating costs estimated. Initial economics showed an attractive return. The operating costs were among the lowest in the industry. The positive economics, along with the excellent results by the products in the marketing tests to the paper, paint, and plastics industries, led to the recommendation to proceed with the project. Plant construction began in June of 1985. The Montana Talc Co. (MTC) analyzed the data from the commercial tests. Based on the product's outstanding performance and the uniqueness of its high purity and platy structure, a strategy was developed to position the company as a premium talc supplier.

Jan 1, 1989

By S. Henley

There is much in common between the requirements of open-pit mining and quarrying operations. Both involve the extraction of large volumes of material from surface excavations. The principal differences are of degree: open-pit mining of materials such as coal or gold generally involves the extraction of only small volumes of 'mineral' and large volumes of waste-they are operations with very high stripping ratios, and are made viable only because of the high unit value of the extracted mineral. In quarrying operations, the unit value of the mineral - sand, aggregate, limestone, or clay - is much lower, but stripping ration Are also lower. Thus the same techniques of geological modelling, reserve estimation, and pit planning are applicable, as is shown in two examples from the British quarrying industry. In each case, a primary requirement is the definition of production volume or tonnage. Sometimes, this need may be addressed simply by the use of a survey data processing package. However, in other cases, such as the two examples addressed in this paper, of sand and clay quarries, detailed assessment of the variation of mineral grades is a vital part of the exercise, and simple volumetric modelling cannot in itself be sufficient. In these cases, a block model approach using simple logical and numerical post-processing is also required to obtain required parameters for commercial classification of the products to be extracted. Pit designs themselves may be optimised by use of algorithms such as Lerchs-Grossmann, but the value of mineral produced can be dependent on factors other than its grade in any one part of a single pit, and the 'optimised' pit itself must be considered only a good sub-optimal. Given the right degree of healthy skepticism, and a software package with sufficient flexibility to be adapted readily to the rather different requirements of the quarrying industry, there is no reason why the quarrying industry should not benefit from the many years of investment in mining software technology.

Jan 1, 1989

By Ronald C. Bethard, Kenneth W. Ely

The liberation of methane during underground coal mining causes serious safety concerns. During a mining cycle, with mechanized mining equipment, thousands of cubic feet of methane are released from coal seams, discharged to return air courses, and vented to the atmosphere through mine fans. This has been the traditional way of removing the explosive hazards of methane gas from the mine. Through horizontal and vertical degasification techniques, this hazard can often be handled in an equally safe and much more profitable manner. Basically, degasification allows for the controlled reduction of inseam methane content of coal prior to its mining. It is the responsibility of mine management to evaluate these degasification programs and ensure that the program itself does not introduce some new risk to the mining process. The removal of methane gas from underground coal mines using horizontal and vertical degasification is a relatively new concept. Products and systems used in degasification continue to evolve. Site conditions vary also, so no one system or equipment can be said to be the safe answer for degasification in all situations. A constant process of cooperation and evaluation by mining and degasification management should result in a safer and more profitable mine.

Jan 1, 1989

By Jr. Neudecker

Rock melting technology can provide in-situ glass liners in nuclear waste package emplacement holes to reduce permeability and increase borehole stability. Reduction of permeability would reduce the time and probability of groundwater contacting the waste packages. In-creasing the stability of the storage boreholes would enhance the retrievability of the nuclear waste packages. The rock melting hole forming technology has already been tested in volcanic tuff similar to the geology at the proposed nuclear waste repository at Yucca Mountain, Nevada.

Jan 1, 1989

Relatively lower recoveries (60%) of coarse phosphate (-16 +35 mesh) particles are attributed to the difficulty in transportation of coarse particles from the pulp to the froth column and rapid drainage of these particles from the froth column to the pulp. Increasing the hydrophobicity of coarse particles by higher, more efficient coating of the collector and using larger froth volumes have been suggested to overcome these problems. In this study, the role of emulsification of the fatty acid-fuel oil collector on the flotation recovery of coarse particles was examined. It was determined that emulsification can not only increase the coarse particle recovery, but do so at higher fractions of fuel oil in the collector, thereby reducing the reagent cost as well.

Jan 1, 1989

By D. L. Johnson

A number of small but rich copper sulfide (chalcocite) ore deposits are located on Michigan's Keweenaw Peninsula. These deposits are considered too small to warrant the capital investment required for conventional mining. However, they are being considered for in-situ solution mining as a way to revitalize the area's once prosperous copper extraction industry. Geology, mineralogy and geohydrology of the deposits have been investigated to determine their suitability for leaching; Three conclusions were drawn from the work. First, the sulfide mineralization is found primarily in fractures (65%) and, therefore, is accessible to injected leach solutions. Second, the ores are shallow, occurring from surface exposure to about 200 meters depth; injection and recovery wells would not have to be excessively deep. Third, the rock was found to have low permeability, in the neighborhood of thirty millidarcys or less. However, preliminary hydraulic fracturing experiments indicate that this will be an effective method for permeability enhancement. In one experiment a permeability increase of 100 times was achieved using a very low injection pressure at shallow depth. Additionally, fracture aperture spacings measured from drill core were correlated with fair success to field permeabilities.

Jan 1, 1989

By Y. J. Wang

Along with the inexpensive availability of computing hardware, a proliferation of powerful personal computers is being realized throughout the mining industry. People from every arena within the industry are designing, developing, and/or applying mining specific software, which is increasing at a rapid rate. In this section applications (or potential applications) that are being made in the analysis and design of mine systems are discussed, including the design of compressed air networks, the simulation of hoisting operations, analysis of longwall face maintenance, and a summary of computer and software applications for analysis and design of coal operations. In "Computer Aided Design of Mine Compressed Air Networks" the authors describe software, called CompAir, and the underlying theoretical and mathematical foundations of it that can be used to make accurate, cost-effective designs of compressed air systems for mines. It includes algorithms for network analysis and the optimization of pipe diameters. The techniques embodied in the software replace traditional rule-of-thumb approximations which have been used in the past and avoid the operating problems that often result from using average, steady-state parameter values, estimated for ideal operating conditions. CompAir, coded in Turbo Pascal for personal computer use, bases calculations on compressible fluid theory, which gives more accurate results than incompressible fluid theory whenever high flow rates or long line distances are involved. The net- work and pipe diameter analysis is formulated as a nonlinear programming problem. The solution technique requires a trial and error approach that iteratively applies the unconstrained optimal pipe diameter algorithm to successive solutions of the constrained network problem until the diameters become "fixed." The authors conclude by recommending the use of a mine-wide monitoring system to improve cost control and provide a better understanding of flow regimes in compressed air networks.

Jan 1, 1989

By Uday Kumar

This paper presents details of an availability study for a fleet of diesel engine operated load-haul-dump (LHD) machines used in a Swedish mine. For the purpose of this study, the LHD machines have been considered as a system comprised of many subsystems like engine, brake, transmission, etc., in series. As availability is dependent on both the reliability and maintainability characteristics of the system, together with reliability, the concepts of maintainability are also discussed. The need for exploring the data for the presence of any structure, which is very common in repairable system data sets, is emphasized with suitable examples. Simple graphical techniques are used for verifying the independent and identically distributed (IID) assumption for the data set. The error introduced due to the use of the exponential distribution in place of more appropriate distributions in estimation of availability and reliability characteristics is analysed.

Jan 1, 1989

By E. Fahrenkrog

An intelligent supervisor developed using expert system tools and applied to a crushing plant is presented in this paper. The structure of this supervisor, based on a model of a human operator, consists of a Knowledge base containing a qualitative model of the process, and a Rules base with the heuristic logic used by an operator when supervising a plant. The simulation results obtained show the potential of this type of systems to supervise the automatic operation of a plant.

Jan 1, 1989

By Vljay K. Chhipa

Artificial intelligence is" an emerging technology in the field of computer application. Expert system have been developed to imitate human intelligence and reasoning process. Expert systems have much scope of application in the decision making process in mineral exploration as such decisions are highly subjective and expert opinions are very helpful. This paper presents a small expert system to analyze reasoning process in exploring for uranium deposits in sandstone.

Jan 1, 1989

By J. Brent Hiskey, Srini Raghavan

The physical chemistry of dissolution of silicate and complex oxide ores in aqueous lixiviants has been reviewed. Particular attention has been paid to the analysis of dissolution mechanisms and kinetic models and to the elucidation of the role of the porous nature of the materials on dissolution behavior. Importance of the physico-chemical characteristics of the leach residues on leaching efficiency has been discussed.

Jan 1, 1989

By C. J. Lewis

Commercial lime plants in the United States and Canada are depicted in Figure 1. The sources of lime available to Nevada and bordering states are rather few. Chemstar Lime has plants at Apex, Nevada and Nelsen, Arizona. Continental Lime, Inc. has plants at Tacoma, Washington, Townsend, Montana and Delta, Utah. However, Continental Lime has a new rotary kiln installation underway near Wendover, Nevada. This plant is scheduled to come on stream in the fall of 1989.

Jan 1, 1989