Search Documents

By L. G. Austin, R. C. Klimpel

Batch breakage kinetic tests were performed in a mill of 0.3 m diameter for a range of mill conditions. Accurate simulation required the measurement and use of factors which accelerated the specific rates of breakage of the top sizes as finer material accumulated in the slurry. These factors depended on the size distribution expressed relative to the top size, not the absolute size, suggesting that they are due to a packing effect not a rheological effect. The data simulated correctly a series of steady-state continuous tests in a mill of the same diameter providing values were corrected to the hold-up, ball load, slurry density, and size distribution measured in the continuous mill tests.

Jan 1, 1990

By Bruce R. Sutherland, Jim B. Ramsden, Gerry L. Bolton

Conductive metal powders are important building blocks for today's micro-electronic circuitry. Formulated into inks, they provide the interconnects needed to complete a complex integrated circuit and the means to enter the world of miniaturization. Traditionally, the inks have been based upon expensive metals such as silver, palladium, platinum and gold because of their excellent electrical conductivity and resistance to corrosion and oxidation. The use of a copper based ink, as an alternative to precious metal inks, recently has received considerable attention. Instability in the prices and limited supply of certain precious metal systems have driven up production costs, making the development of a lower cost copper system more attractive to manufacturers. However, lower production costs are on1 y real ized if performance and reliability can be maintained. While the development has been driven by cost, copper does offer some significant performance advantages over noble metal systems: conductivity as good as silver and 4W better than gold; leach resistance better than silver and equal to gold; stability at high frequencies better than gold or silver; strong film bonding characteristics; and compatibility with most solders. These benefits, however, do not come without cost. The inherently reactive nature of pure copper, while providing unique performance properties, makes it difficult to process. Unl i ke precious metals which can be fired in air, copper would oxidize and so requires special furnaces and atmospheres. Despite these difficulties, the transition from precious metal thick film systems to copper is gaining momentum. Manufacturers of high density, high performance circuitry are exploring the performance advantages of copper over gold and silver and the manufacturers of consumer products are considering the potential cost savings of copper over silver-palladium. Sherritt has developed a fine copper powder for this industry. Through association with the ink manufacturers, it has been found that performance properties of the ink vary with the physical and chemical characteristics of the powder. Production Process The production of very fine copper powders at Sherritt is based upon the disproportionation of cuprous ions as outlined in Equation [1] (1).

Jan 1, 1990

By V. K. Karra

Based on extensive investigations on the effect of design variables on process performance from 1982-85, Nordberg developed a 746 kW (1000 hp) cone crusher with the objective of boosting crushing productivity in existing plants. The MP1000 fits on the same foundation as the 2 m (7 ft) SHD Symons cone but is designed to give two times the capacity of the 2 m (7ft) The economies of scale involved give the customer substantial cost savings. In this paper, process performance of the Nordberg MP1000 relative to the 2 m (7 ft)SHD Symons cone while crushing the same ore, will be presented. Also, implications of such a crusher scale-up to associated cost savings will be addressed.

Jan 1, 1990

By Samuel B. Romberger

During the formation of most epithermal precious metal deposits geochemical changes can be characterized by the introduction of large amounts of silica, minor amounts of sulfur, and trace quantities of gold, silver, and other metals. During the same process, large amounts of alkalis and alkaline earth elements, such as sodium and calcium, and sometimes aluminum are removed from the rocks. In deposits hosted by carbonate sedimentary rocks large amounts of carbonate may be removed before or during the silicification process. Small amounts of iron may be introduced by the mineralizing solutions, however, in most epithermal deposits this may be a relatively immobile component and is locally derived. The results of these changes are deposits consisting of up to 90 to 95 percent silica as quartz veins, breccias, silicified host rocks, and jasperoids containing a few percent sulfides, mostly pyrite, and a few parts per million gold and silver. Other minerals commonly but not always present are barite, arsenic, antimony, or mercury sulfides, and tellurides. Often gold shows a spatial, and therefore an apparent genetic, relationship to pyrite in primary ores. Alteration and gangue assemblages sometimes include sericite and/or adularia, and parts of the deposits may contain alunite and/or clay minerals. Even though the value of these deposits usually lies in their gold content, silver is usually present in larger quantities than gold (Romberger, 1990). Based on these general characteristics observed in a large number of epithermal deposits, together with processes occurring in active geothermal areas to which they are often genetically linked (Henley, 1985), a model is proposed whereby deposition occurs along a subhorizontal zone separating environments of contrasting chemistries. The upper environment is characterized by oxygenated acid waters and the deeper environment by a reducing near neutral aqueous system. The model describes the chemical changes occurring as a result of mixing and/or boiling within this zone. It builds upon the physical models proposed by Romberger (1988a) for disseminated gold deposits and Bonham (1988; 1989) for volcanic rockhosted deposits.

Jan 1, 1990

By Paula N. Wilson, W. T. Parry

Carbonaceous and metalliferous black shales occur in close proximity to Mercur-type gold deposits in the southern Oquirrh Mountains, Utah. These shale units, the Manning Canyon shale and the Long Trail shale, have undergone regional hydrothermal alteration. Hydrothermal solutions oxidized organic matter and pyrite, replaced shale by hydrothermal phyllosilicates and silica, and replaced fossils by phyllosilicates. The shales are depleted in organic carbon, calcium carbonate, alkali and alkaline earth metals, and enriched in aluminum and hydrogen. Hydrothermal veins containing illite, chlorite, pyrophyllite, kaolinite, Fe-oxides, and sulfides are present throughout the study area.The illite in veins is an ammonium illite that contains up to 2 % NH4 and is correspondingly depleted in K. Correlations among Au, As, Hg, TI, Sc, and rare earth elements indicate that hydrothermal fluids responsible for formation of ammonium illite were gold bearing. K/Ar ages of illite veins and illite-rich, clay-size separates of altered shales indicate hydrothermal activity occurred in the time range 193 to 122 Ma. Several ages from clay-size separates within the Mercur district cluster near 160 Ma. These ages are coeval with thrust faulting recognized to the north and west.

Jan 1, 1990

By M. G. Hester

The inadequacy of traditional geostatistical methods for estimating some precious metals deposits has become apparent in the last few years. New methods or estimation such as Indicator, Probability and Multigaussian Kriging are difficult to understand and apply. Case studies using a new method of variogram calculation proposed by Srivastava show the method valuable for variogram estimation in precious metal deposits. Some simple, sometimes unorthodox. estimation methods that have proved useful in Some situations are presented.

Jan 1, 1990

By Chen L. Lin, Luis R. M. Bittencourt, Jan D. Miller

Recently research efforts have been made to obtain a high-purity gibbsite concentrate, suitable for first-class alumina refractories, from a Brazilian bauxite ore containing gibbsite (50%), quartz (35%),and kaolinite (15%). Detailed polished-section microprobe analysis was used to describe the liberation characteristics of the ore. Experimental results suggest that the kaolinite liberation characteristics can be described by King's liberation model and that only about 11% of the kaolinite is expected to be liberated at a particle size of 75 µ. Bench-scale experiments for the flotation of gibbsite/kaolinite from quartz using alkyl sulfates as collectors were particularly successful at pH 2, and under appropriate conditions a concentrate containing 93.0% A1 0 (calcined basis) was obtained 2 3 at a gibbsite recovery of about 96%. Subsequently, the more difficult separation of kaolinite from gibbsite was accomplished by kaolinite flotation from the alumina concentrate with a quaternary ammonium salt at pH 6 to produce a high-purity gibbsite product, 97.4% A12O3 (calcined basis), at an overall gibbsite recovery from the bauxite flotation feed of about 90%.

Jan 1, 1990

By K. V. Viswanathan, P. Sornasundaran, S. E. El-Mofty

Dolomite is found to undergo preferential dissolution in aqueous solutions and this is found to be strongly dependent on the solid to liquid ratio (SIL). Electrokinetic studies done under the sump conditions revealed that the mineral surface charge is also affected markedly by the solid content in the suspension. Conditioning of the dolomite at low SIL ratios for short time intervals showed preferential dissolution of calcium leading to a magnesium-enriched dolomite surface. At higher SIL ratios and longer conditioning times, calcium depletion from the solution and a calcium-enriched dolomite surface resulted. The results are discussed in terms of surface precipitation and/or bulk precipitation and surface conversion of dolomite to the calcium-enriched phase (calcium carbonate and/or magnesian calcites).

Jan 1, 1990

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed to improve the metallurgical efficiency of the concentrators with a view to improve the production of concentrates both qualitatively and quantitatively.

Jan 1, 1990

By C. Maltesh, P. Somasundaran

The ever increasing need for treating fine complex mineral bodies has led to the evolution and rapid development of advanced processing techniques for fine grinding, classification an if mineral separation and purification. With the introduction of these new technologies and understanding of underlying fundamental principles, mineral processing is now being applied to materials ranging from ceramics and composites to superconductors. In this review, current and potential applications of mineral engineering techniques to advanced materials processing are discussed. Particularly, material processing involving ultrafine grinding, dispersion and flocculation and thin film formation is examined. Novel techniques of solid/liquid separation involving manipulation of interfaces and use of high intensity high gradient superconductor magnetic equipment for solid/solid separation are discussed.

Jan 1, 1990

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By D. Robert Weir, M. J. H. Ruscoe, R. M. Berezowsky, M. A. Clegg

The metallurgical processing involved in the produc-tion of the new Canadian one dollar coin is reviewed starting with the hydrometallurgical production of pure nickel powder, followed by the powder metallurgy process for the production of nickel strip and coinage blanks, and concluding with the Aureate bronze electroplating and heat treatment procedure. Coinage requirements are then reviewed with regard to economic, public acceptance, and service requirements. Finally the properties of Aureate nickel coinage are presented in the light of the many and varied coinage requirements, and it is concluded that the new Canadian dollar coin exceeds the requirements admirably.

Jan 1, 1990

By D. Nilsson, B. Aaro

To find out if there are any potential savings in "in-the-wall haulage for open pits," the Swedish companies ASEA and Kiruna-Truck in 1984 gave us financial support to study this solution in more detail. In the study, the use of in-the-wall haulage was studied for three hypothetical open pits with different sizes and shapes. Annual ore production rates also varied. A part of this thorough study was published by the Swedish Mining Research Foundation (see Report F 8444, "The Use of Electric Trucks and In-the-Wall Haulage in Open-Pit Mining," in Swedish with an English Summary). Although in-the-wall haulage is of interest in some open pits, the local terrain is important for profitability. The authors do not think in-the-wall haulage is of any major interest for the mining industry. The following is a summary of some of the author's findings. To place the haul road in the wall is not of interest in open pits with declining metal contents in the bedrock. In such mines, the volumes from the haul roads will not yield revenues. The cost per m3 for an underground haul road is much higher than for a haul road in the pit. This means that it is only of interest to place the haul road in the wall when mining gets deeper than about 50 m (165 ft). In-the-wall haul roads will reduce flexibility in the pit, and it will make necessary the use of smaller equipment with lower productivity and higher costs per ton. As Hustrulid, et al. show (Table 4), excavation savings of material hauled are very low, $0.10 to $0.25/t (0.09 to 0.27 per st). The extra operating cost, due to lower productive equipment, will normally be much higher and thus destroy the whole idea with in-the-wall haulage. If electric trucks are profitable for in-the-wall haulage, it is normally also profitable to use electric trolley assist for trucks on the haul road in the pit. But the profitability of using electric power is different in different countries, and depends on the relation between the cost for electric power and diesel fuel. In the US, diesel fuel is inexpensive compared with electricity, but in a country like Sweden, diesel fuel is much more expensive. In most open pits, the trucks have to move a considerable distange from the loader until they reach a final haul road in the wall. A trolley line along such temporary haul roads will be exposed to flyrock. It is normally less expensive to perform rock support from the open pit than from underground ramps in the wall. In Fig. 8, Hustrulid et al. gives the impression that the underground haul roads will be very close to each other. This is seldom the case. Figure 1 shows a haul road in the wall. The haul road passes through each cross-section only once. Arranging a reliable dewatering and rock support system from only one underground ramp is probably impossible. Many more drifts are therefore necessary. In our report, we also studied what would happen if the final pit slope is increased by 5°, using underground drifts in the wall. Our conclusion was that, the extra cost for drifts, rock support, pumps, etc. destroys the whole idea, and that it was better to accept a higher stripping ratio with the haul road in the pit and to use conventional low-cost open pit equipment. Finally, we think it is would be difficult to try to reduce the safety factor when determining the slope angle by moving the haul road in the wall. Minimizing the risk for pit wall collapse is also important with in-the-wall haulage, primarily because men and equipment will be working in the pit, but also to guarantee many accesses between the pit and the haul road in the wall.

Jan 1, 1990

By J. B. Hiskey, V. P. Atluri

Resin-in-leach (RIL) cyanidation experiments were performed on a refractory carbonaceous gold ore. The objective of this investigation was to determine if strong-base ion exchange resins could adsorb the soluble aurocyanide complex in preference to natural "preg robbing" organic constituents. Direct cyanidation of the carbonaceous gold ore used in this study resulted in less than 2% gold extraction in 24 hr. RIL cyanidation resulted in about 70% gold recovery onto the resin. Kinetic experiments indicated that 50% of the gold is extracted after 1 hr of leaching. Resin breakage was investigated for as-received and preattrited resins. Similar results were obtained with three different strong base resins.

Jan 1, 1990

By W. V. Harper

The travel path of a freed radioactive particle in an aquifer must be estimated from a limited number of available samples. This paper discusses geostatistical methods that minimize the 'uncertainty' associated with the predicted hydrologic surfaces and the predicted travel path. However, any estimation method will produce a single smooth predicted path. This 'sensitivity' will he evaluated using a geostatistical simulation method. The techniques will be illustrated using published data from the Wolfcamp and Pennsylvanian aquifers in the northern Texas Panhandle.

Jan 1, 1990

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. This paper focuses on the KRS Algorithms that extract key information from lists of time study type event sequences. Because a static system cannot operate effectively in a dynamic mining environment, we are prototyping an index based technique that allows the system to adapt itself to this dynamic environment.

Jan 1, 1990

By D. L. Jones, S. Knoerr, J. Mansanti

The Buckhorn Mine in Nevada currently treats oxide ore using heap leach methods, but exploration has identified sulphide reserves which are refractory in nature. Preliminary testwork was conducted on the sulphide material to screen potential pre-cyanidation treatment methods. Processes evaluated included pressure oxidation, biological oxidation, nitric acid oxidation and roasting. An initial economic and process analysis of the results concluded that roasting was the only viable process, and only if the roaster off-gases were converted to soleable sulphuric acid. Further economic analysis indicated that roasting of the whole ore was more attractive than pre-concentrating by flotation, followed by roasting of the concentrate. These results were generalized to show that for high sulphur ore a roaster/acid plant combination is more attractive that either of the other options, ie. pressure leaching or bioleaching, provided the by-product acid is soleable.

Jan 1, 1990

By Pierre Ollivier, Dominique Morin, Pr. Ivo Toromanoff

Refractory gold ores have been processed by bio-hydrometallurgical process at B.R.G.M. (Bureau de Recherches Géologiques et Minières), Research Centre ,Orleans,France. The liberation of gold has been studied and the following steps for gold recovery improved. The overall process flowsheet has been established comprising different ways of treatment before the final discharge of the effluent. Iron and arsenic are successfully precipitated under well controlled Eh-pH conditions. Long term stability tests have been conducted and the research programme is to be continued with the crystallo graphic studies of the precipitates. Economical studies have been performed on the base of data obtained on parameters studies.

Jan 1, 1990

By C. B. Alcock

The control of high temperature processes requires the ability to measure significant variables during operations. With increasing automatic computerized control there is need for sensors which can provide on-line chemical analyses of all phases present in a reactor without the necessity to withdraw samples from the high temperature reaction zone. Probes using electrochemical cells and conductivity measuring devices have provided the answers to some of these problems, notably the measurement of oxygen in liquid metals, and similar potential systems based on the same fundamental principles for the analysis of non-metallic and metallic elements appear feasible. In this discussion, the state-of-the-art in chemical sensors will be discussed in terms of the potential materials of construction, and, in some cases, the limitations of upper temperature at which some promising systems can, at present, be applied. It is concluded that a new phase of basic research could improve the outlook substantially by providing solutions for some problems in chemical sensors which are now well-defined.

Jan 1, 1990

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equipment, blasting, or water infusion. To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in.- diam). The techniques in detail are somewhat complex and subject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1990