Search Documents

By S. P. Banerjee

There has been a phenomenal increase in production of coal from opencast mines in India. At the same time environmental problems caused by mining are receiving greater atttention. Deterioration in ambient air quality due to increased concentration of suspended particulate matter (SPM) in and around an opencast project is a major problem. Some measured values of SPM level around opencast mines in diff coalfields show that in many cases the TLV of 500 ug/m^3 is exceeded. The impact of dust emission from a mining project on surrounding areas are estimated by using computer models for air pollution dispersal but such treatment suffers from errors in predicting the dust load and failure to take into account the terraced nature of the opencast mine site. The haul roads have been identified as the most prolific source of dust and some recent trials on haul road dust consolidation in Indian mines are mentioned in the paper. Statistics regarding pneumoconiosis cases in Indian coal mines for the last decade are presented to show an increase in reported cases and a gist of the recently amended regulations on the subject of precaution against dust is mentioned.

Jan 1, 1991

By J. A. M. Cano

An extensive research work was developed by Samarco Mineracao S/A to study the quality characteristics of blast furnace pellets produced with high content of MgO. Comparative blast furnace simulation tests were conducted both in Samarco and foreign laboratories. The objective was to evaluate the behavior of high MgO and normal Samarco pellets in the blast furnace operation. Additives such as dolomitic hydrated lime, dunite and magnesite were used for increasing pellet MgO content. The test results showed that pellets produced with high MgO content are similar in quality to normal Samarco Pellets.

Jan 1, 1991

By L. A. Morley, S. C. Gambrell

Behavior of a jour-leg shield design used on a soft floor in an operating longwall system is presented. The shield examined in this study was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the magnitudes of typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments required to produce the deformations are calculated based on the mechanical properties of the material. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1991

By Jin Anshi, Wang Dai, Wang Zingshen

Both fire and gas problems in Fully Mechanized Sublevel Caving Coat Face are quite different from those in common fully mechanized coal face. Pouring N2into the goaf would be the best method to prevent fire in the goaf. In this paper how to determine parameters of pouring N2 is discussed. Comparing distributions of gases and temperature before pouring N2into the goaf with those after pouring N2 into the goaf, the effectivenesses of preventing the fire by pouring N2 into the goaf are testified. Some special gas problems appear in Fully Mechanized Sublevel Caving Coal Face, which are proved to be serious and interrelated with pouring N2 into goaf. Finally, a few methods adopted to deal with gas problems are described simply.

Jan 1, 1991

By Dale C. Matthews

Pressure oxidation of refractory gold ores is becoming more popular in what has become an environmentally sensitive society. This article discusses some specific process problems and solutions involved with starting up and operating an autoclave circuit. The Getchell gold deposit is located about 72 km (45 miles) northeast of Winnemucca, NV. The deposit was discovered in 1934 and first production came about in 1938. The oxide portion of the ore body was mined and milled from about 1936 through 1950. Refractory arsenic-bearing sulfide ores had long been known to exist in the Getchell deposit. These ores had been mined concurrently with the oxides since 1938.

Jan 1, 1991

By Enrique Farjeat P.

Mexico City's growth has encourage development of underworks to meet drainage and transport requirements. Deep Drainage System has been constructed through a complex tunnel network, 108 km in total, varying from 30 to 12 m in depth and 6.24 or 4.00 m in diameter. Wide range of stability conditions presented in soils has forced the use of several tunnelling methods, going from the manual procedure by the use of pneumatic tools, to slurry shields, or open face shields, with the aid of or without compressed air. For transport, subway tunnels have been excavated in very compact silty sands, 9.15 and 9.51 m in diameter, with the use of open shields one of which was designed by Mexican engineers as a prototype machine. This paper tries to describe evolution of tunnelling methods used in Mexico City during last 20 years.

Jan 1, 1991

By Neal Rackstraw, Mamo Meaza

Washington Metropolitan Transit Authority Section E8a consists principally of twin tunnels 1,713 meters (5,620 ft) long, excavated to a diameter of 6.35 meters (20.83 ft) using an open face shield, with a primary lining of four unbolted precast concrete segments expanded at the crown, and a full circle unreinforced concrete final lining with a finished tunnel diameter of 5.08 meters (16.67 ft). The tunnels, constructed in Cretaceous age sediments, are mostly in stiff to hard clay except for a few areas along the alignment that contain dense to very dense fine sand in the upper portion of the tunnel that created a mixed face condition. At two locations unexpected heavy water inflows produced very serious problems in both tunnels. Water flows in the interface area were generally more than 378.5 1pm (100 gpm) and reached as high as 2,649.5 1pm (700 gpm) in the mixed face ground. The nature of the tunnel inflows, the consequences, and the corrective measures adopted will be the subject of this paper.

Jan 1, 1991

The paper presents results of the mineralogical examination on samples from a bacterial leaching test which simulated in situ leaching for 482 days. Rock fragments (15 to 20 cm) were obtained from the top, the middle and the bottom of a bioleach column. Examination of the samples was carried by electron microscopy and image analysis. The surfaces of the rock fragments were studied to characterize the precipitation products, and cross-section cuts were studied to assess the advance of the bacteria leaching front and the dissolution of the different sulphide minerals.

Jan 1, 1991

By N. B. Greninger, M. J. Sapko

The US Bureau of Mines conducted, through joint funding with the Colorado Mining Association, large scale oil shale rubble fire tests to investigate flammability characteristics and different methods of extinguishment. Ignition of large rubble piles was easily accomplished. Foam blankets could be used to control surface flames. The results of these large scale tests confirmed that water was effective but not particularly efficient in extinguishing deep seated oil shale fires. It took up to 1.7 times as much water to extinguish afire as anticipated on the basis of a simple cooling model, assuming 100% utiliza-

Jan 1, 1991

By T. B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores and, for major veins, their great vertical range (>990m). Less well-documented are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine, and volcaniclastic rocks deposited within the diatreme complex. The ore-gangue minerals Here precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate, and oxide minerals along with minor base metal sulfide and precious metal telluride-s. Wallrock alteration is quite limited adjacent to veins and somewhat more extensive within hydrothermal and tectonic breccias.

Jan 1, 1991

By James Barker, Jacques Renault, Chris McKee

Previous XRD work by us (McKee, Renault, Barker; 199Oa, 1990b) showed that by using pressed powder briquettes and a peak deconvolution technique, quartz in perlite can be routinely determined at <0.1 wt. %. In the present report, we discuss two additional methods of standardization: 1) chemical determination of quartz in silicate standards and 2) addition of a large amount of quartz to an unknown mixture. The first method applies the concept of mass balance and is sensitive to the analysis of silica and a monitor element. The second minimizes mixing errors; its equation is non-linear and is derived from the two component case with unequal mass absorption coefficients treated by Klug and Alexander (1974).

Jan 1, 1991

By James C. Norman

The boron review arrived too late to appear in the June issue. The US was the world&apos;s second largest producer and the largest consumer of boron compounds during 1990. Boron mineral concentrate and chemical production in the US totaled 1.13 Mt (1.2 million st), including 565 kt (662,800 st) of boric oxide (B2O3) in 1990, according to US Bureau of Mines estimates. Total value amounted to $404 million. This was slightly higher in production than 1989 but down in value, reflecting a softening in boron product prices. Total world production of boron mineral concentrate and chemical tonnage in 1990 was estimated at 3 Mt (3.3 million st), which corresponds to about 1.3 Mt (1.3 million st) of BO,. World production in 1990 was about the same as in 1989.

Jan 1, 1991

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By William Petruk

Performance assessments are carried out to monitor operations, to evaluate performance and to identify processing problems. The assessment involves collecting and analyzing representative samples from critical points in a flowsheet and interpreting the data. Sample analysis techniques include chemical analyses, mineralogical investigations, mineralogical analyses, and materials balancing. Chemical analyses provide the lowest cost assessment and should be used liberally, particularly in monitoring a process. Materials balances performed on chemical assays for a suite of samples are used as a first step in evaluating a process. Mineralogical investigations are more expensive than chemical analyses but need to be used only at the beginning of mining and metallurgical operations and as a second step in assessing processing problems. Quantitative mineralogical analyses combined with materials balancing provide the most complete performance assessment, but the procedure is expensive. On the other hand, the assessment has the potential of a large payback when carried out where warranted.

Jan 1, 1991

By K. A. Natarajan, M. K. Yelloji Rao

Significance of grinding media wear and its effect on chalcopyrite flotation are discussed. Laboratory marked ball wear tests were conducted grinding chalcopyrite ore and quartzite dry, wet, and with collector added during grinding. The effects of oxygen and nitrogen on ball wear were evaluated by the addition of chalcopyrite mineral while grinding quartzite. The effect of dry and wet grinding on chalcopyrite flotation was also studied. Results show abrasive wear is greater in quartzite grinding than in grinding chalcopyrite. Oxygen increases the corrosive wear of high carbon low alloy steel balls in the presence of chalcopyrite ore. Chalcopyrite flotation was retarded due to wet grinding in the presence of oxygen. Though collector reagent increased the media wear, it improved the flotation of chalcopyrite. Probable electrochemical reactions encountered in a grinding mill are outlined.

Jan 1, 1991

By R. R. Beebe

When an economic mineral deposit is first discovered, it is almost immediately defined in terms of tonnage and grade. As exploration and assessment continue, the initial definition is ordinarily qualified by such terms as "proven," "probable" and so on. Even at this stage, the fundamental philosophies of the discoverers may manifest themselves in conservative or optimistic views of the deposit&apos;s potential. It is unusual, however, for the philosophies to be expressed in terms of metallurgical performance criteria at such an early stage unless the ore is very unusual in its chemistry or mineralogy. Even before drilling is completed, the first mining plans appear, with or without the benefit of metallurgical test data. This is the point at which management philosophies can have some of their greatest impacts. In ideal cases, where large, uniform ore bodies can be developed and mined according to assay cutoffs, the conventional philosophy of maximizing tonnage while minimizing cost can be followed without much metallurgical difficulty. Unfortunately, such cases are rather uncommon. Even large, low-grade

Jan 1, 1991

By P. K. Sims

Extensive mineralization in the basal part of the Duluth Complex of Middle Proterozoic (Keweenawan) age in northeast Minnesota has been explored during the past 30 years as a potential source of copper and nickel from sulfide-bearing assemblages. Very large resources of low grade and marginal material have been delineated by drilling and by test shafts sunk by at least five private mining companies, but none of the properties has yet been mined. With few exceptions, grade and tonnage figures for specific properties have not been released, but the magnitude of the resources has been estimated by the Minnesota Geological Survey and the Minnesota Dept. of Natural Resources as constituting several billion tons of low grade and marginal copper- and nickel-bearing material - a major combined copper-nickel resource of international importance.

Jan 1, 1991

By R. F. Kovar, R. N. Torbin, R. E. Gundersen

I have to express my .surprise and must send a note of warning concerning the use of polyurethane foam as described in a paper by R.N. Torbin and R.F. Kovar, entitled "Innovative Shaft Lining Method," published in your February 1989 edition. In September, 1986, 177 miners lost their lives when they were exposed to fumes downwind from a fire in a tunnel lined with polyurethane foam. Whilst polyurethane exhibits reasonable fire retardent properties in small-scale tests, mass use in a tubular configuration, exacerbated by the furnace effect of cross-radiation, can lead to a rapid, uncontrollable conflagration. I do not wish these comments to detract from the engineering achievements of the authors but rather to sound a loud warning as to the application of the system. Any shaft designed for human access- be it for transport or shaft work - and any intake airway, should not consider the use of polyurethane foam. It only needs a slip with a cutting torch or an electric fault to initiate a disaster. Many countries have banned or restricted the use of polyurethane foam in the workings of a mine and maybe alternative foams (e.g. phenolics) can be used or developed

Jan 1, 1991

By R. G. Reddy

Viscosities of Feo-SiO2 slags were calculated using the previously developed structural based model. An expression was derived using hole theory and the atomic pair model to relate the NO0 and temperature to the viscosity. The deduced equation n=4.9x10-9 T1/2 NO0 exp (E/RT) poise was successfully applied to predict the viscosity of FeO-SiO2 slags in the composition range of 0.1 < XSiO2 < 1 for several temperatures. The calculated data agrees well with the experimental viscosity data.

Jan 1, 1991

By H. Lyn Bourne

This is the ninth annual tabulation of royalty information. Again this year, some of the older information has been deleted to make room for more than 30 new entries. Several articles and publications crossed the author&apos;s desk this past year that relate to mineral valuation and mineral royalty. Tom Loucks presented a paper, "The Valuation of Hard Rock Mineral Property," at the Rocky Mountain Mineral Law Foundation in Santa Fe, NM in July, 1990. His paper gives an indepth explanation of the definitions and concepts related to mineral valuation. It includes descriptions of numerous legal cases that have dealt with mineral valuation and proper reference is given for each case. Loucks works for the Denver Mining Finance Co. Gold royalties generally range from 5% to 7%, net smelter return. However, Severn Brown sent information that shows a much wider variation. Echo Bay Mines reported in its 1989 annual report royalties that range from 1.5 % to 30% for gold from various gold properties. Brown also sent a copy of an article that appeared in the Dec. 27, 1982, issue of Fortune magazine. This issue carried an article by Walter Guzzardi, Jr. "The Huge Find in Roy Ash&apos;s Backyard." The article gives the history of Newmont&apos;s leasing in Nevada on property that became the Carlin, Bootstrap and Blue Star Mines. The article states that the initial royalty was 10% that escalated to more than 16%. Another property, the site of Gold Quarry, provides an 18% royalty to the same own¬ers. The article makes interesting reading for those interested in mining history.

Jan 1, 1991