Search Documents

By I. Iwasaki, H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothabiliry tests and SEM observations. In the absence of sodium silicate, Ca I+ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: 1) the removal of impurity minerals and calcium-bearing precipitates from quartz surfaces by dispersion, 2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and 3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1991

By J. Hanna, H. R. Gonzalez

Four Ca-bentonitic clays from Alabama were evaluated for use in diammonium phosphate (DAP) or urea ammonium nitrate (UAN) fertilizer suspensions. The viscosity and gel strength of suspensions prepared with different proportions of a Western bentonite clay and sodium-exchanged Alabama clays were measured as a function of clay content and dispersant concentration. The results obtained suggested that three of the Alabama Ca-bentonites would replace about 40% of the more expensive Western bentonite in UAN and DAP fertilizer suspensions. The performance of the Nu-modified clays, prepared according to the Tennessee Valley Authority soda ash method, was as good or even better than those observed for the Mg-, NaIMg- or K-modified clays. The TVA clay modification procedure appears to be reliable and cost effective.

Jan 1, 1991

By Maureen D. Carmen, Joseph L. Zaluski, Gladys Beck Green

The Federal Surface Mining Control and Reclamation Act (SMCRA) requires a surface mine operator to post a performance bond before a mining permit can be issued to that operator. Release of that bond is contingent upon the completion of all required reclamation, restoration, and abatement work on the permit area. This paper explores the requirements of each of the three phases of reclamation under SMCRA, as well as provisions of four exemplar state regulations of four states that have been granted "primacy" under SMCRA. Successful completion of these requirements is a condition pre cedent to the release of performance bond liability. Failure to secure a timely bond release will have an ad verse impact on an operator's other mine permitting activities throughout the United States.

Jan 1, 1991

By H. G. Stephenson

Canada and the United states are both developed countries with economies which are extremely dependant on oil. Canada exports 37% of its production (to the United states) and imports 35% of its consumption (mainly into Eastern Canada), making the country self-sufficient in oil. Canada is attempting to increase its oil production so as to simultaneously reduce its dependence on foreign oil while producing more oil for export. The United states -imports no less than 50% of its total consumption of 17 million barrels/day. Canada's exports to the United states form only 7% of the United States total imports. The United States would clearly prefer to achieve self-sufficiency in oil. Consequently both countries are dependent on foreign oil. The united States is however in the sensitive situation of depending, for its imports, on countries which are susceptible to destabilizing political events. It is the author's hypothesis that recent developments in underground oil recovery from the Athabasca oil Sands of Alberta may well, for both countries, form part of the solution to these problems.

Jan 1, 1991

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By G. G. O. O. Uwadiale

Starting from a crude ore assaying 45.6% Fe, a fine-grained oolitic iron ore was concentrated by the oil agglomeration technique to 90% Fe recovery and 65% Fe assay. The ore required grinding to minus 5 µm to effect adequate liberation, and the technique yielded optimum results at pH 9. The roles of pH, collector, and bridging liquid concentrations on selectivity and yield of iron minerals in the concentrates are discussed.

Jan 1, 1991

By C. J. Bise

Continuous mining accounts for about 69% of the nation's underground coal production. This level is not expected to change much in the near future. This is because continuous mining represents the primary means of under- ground coal production. It is also the primary means of driving development entries for underground coal mines, including longwall mines. The continuous miner worksite contains many characteristics that can lead to personnel accidents. It continues to be an area of concern for mine managers, safety engineers, and training coordinators. In an effort to assist mine management in attempts to reduce the number of accidents and injuries sustained in this area, this paper presents a loss-control-based, non-intrusive strategy for conducting safety evaluations at continuous miner worksites.

Jan 1, 1991

By Gordon F. Revey, Dan Harrison

Hanging Lake Joint Venture recently excavated two conventional 12.8 m (42 foot) diameter highway tunnels in the difficult ground conditions of Glenwood Canyon, Colorado. This paper outlines the type and success of the various Controlled Blasting Techniques that were used to minimize overbreak in the portal and tunnel excavations. The different Smoothwall and Cushion Charge loads used in the different ground types are described in detail. Delay Timing and Drilling Pattern variations are also discussed.

Jan 1, 1991

By D. III Earley, R. L. Blake

The Bureau of Mines is investigating the potential for in situ mining (ISM) of gold and silver mineralization. This preliminary study examined samples from several types of deposits. It used light optical microscopy and the electron microprobe to characterize the ore and gangue minerals and textural features of these samples. This included the spacial relations between the target minerals and likely natural fluid channel ways. Low-grade disseminated deposit types from the western US were found to contain fracture- hosted or matrix-hosted gold and silver minerals, some of which are encapsulated by quartz or pyrite. Successful ISM application to gold and silver deposits needs this data in order to understand potential problems of the lixiviant reaching the ore minerals.

Jan 1, 1991

By R. C. Bryan, D. B. Jamison

This paper describes a procedure for minimizing the operational costs associated with blending sodium in coal at a surface mine in the Powder River Basin. Mine site blending is performed by adjusting daily production rates for high- and low-sodium pits. These adjustments are designed to produce a consistent sodium value called the blending target. The mine's contractual limit for sodium is sufficiently close to the field average value that any decrease in the sodium blending target may result in an opportunity cost, if the number of potentially minable tons is reduced. Conversely, any increase in the blending target may result in a higher sampling cost if more information is required to keep the blend within contractual limits. Blending parameters were defined using a geostatistical block model of sodium content that was based on analyses of hundreds of in-pit sample holes. Variograms for these data were used to compute the marginal costs of opportunity and sampling for a series of hypothetical in-pit drilling patterns. These marginal costs provided a basis for selecting optimum values for key parameters such as the blending target, production variance and in-pit sampling density. The benefit of implementing these optimized parameter values is that operational costs of sodium blending will be minimized over the long-term. At the mine where this procedure was developed, each dollar spent to increase the sampling density to the optimum value was shown to generate a $10 savings in opportunity cost.

Jan 1, 1991

By Svante Lundbrink

A new generation hydraulic rock drill featuring more than 50 percent higher performance than other drills has been introduced by Atlas Copco. In conjunction with the new rock drill, control systems have developed and refined to handle the higher drilling output, and to maintain an acceptable service life of drill string components. These improved features are built into the Rocket Boomer, a new high-performance drill rig, used at the recently completed Hanging Lake project in Colorado. Experiences from this project will be reported together with results from a highway tunnel construction project in Italy.

Jan 1, 1991

By N. P. Reddy, L. Adler

The valuable Maximum Utilization Factor (MUF) concept has been extended to other rotating excavators beyond Stripping Shovels and Draglines. In this concept the boom reach and bucket capacity are multiplied to get an MUF, then normalized by dividing by the equipment weight. Statistical analyses were applied to the remaining shovels (hydraulic and cable), draglines, and backhoes. Positive correlations were found. Stripping Shovels and Draglines were also re-examined. The results provide an estimate of equipment diggability and encourages versatility by the interchange of the boom and the bucket. The concept further clarifies the existing equipment classification by delineating General Excavating, Loading, and Stripping kinds. The results also forecast trends, and noted innovative advances and possible retrogression. Extension to other boom excavators, such as front-end loaders, is recommended. The MUF concept provides one of the few indices of gross external characteristics available to the engineer-user of equipment.

Jan 1, 1991

By J. G. Groppo, B. K. Parekh

A series of performance studies were conducted using countercurrent column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia using a 150-mm (6-in.) inside diameter column that was 5.8 m (19 ft) high. Both thickener feed and classifying cyclone overflow with a typical size distribution of 150 µm (100 mesh) X 0 were tested. The percent solids of the column flotation feed varied from 1.5% to 15% while the ash content ranged from about 30% to 60%. The concentrates produced contained 2% to 10% ash with Btu recoveries of nearly 90% using 0.12 to 1.25 kg/t (0.25 to 2.5 lbs per st) fuel oil and 0.12 kg/t (0.25 lbs per st) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from seven different seams are discussed as well as scale-up relationships used to design a full-scale installation presently in operation.

Jan 1, 1991

By V. Rajagopal

Corrosion and abrasion properties of a series of chromium-containing cast iron balls with Cr contents ranging from 0 to 29% was evaluated and compared with austenitic stainless steel and mild steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite with either 5% pyrrhotite or 5% chalcopyrite under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynamic polarization curves under abrasion. An offset in their electrochemical activities was observed somewhere between 16 and 26% Cr. In fact, 26 and 29% Cr cast irons showed an excellent corrosion resistance approaching that of austenitic stainless steel. Flotation recoveries were estimated on a 95% quartzite + 5% pyrrhotite sample ground with various cast iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with corrosive wear obtained from marked ball wear test and with flotation results.

Jan 1, 1991

By M. F. Gleason, S. Burns, J. R. Arnold

In 1986, Gold Fields began negotiations with a large Nevada electrical power utility to supply power for its Chimney Creek mine in northern Nevada. After the long negotiations reached an impasse over various costs associated with the power line, a decision was made by Gold Fields to generate its own power. Self-generation is not uncommon overseas, but it is rare for any but very large or very small operations in the United States. Surprisingly, under certain conditions a mine can generate its own power profitably, and Gold Fields has found that the associated operating and maintenance problems are minimal. The following report details what factors went into this decision and how it works. Hopefully, it can serve as a guideline for those who may find themselves in a similar position. History In the spring of 1986, Davy McKee Corp. was contracted by Gold Fields Mining Corp. to provide design engineering and construction management for the chimney Creek Mine. Chimney Creek is located about 50 mi northeast of Winnemucca, NV in a remote part of Humboldt County. The nearest industry using utility power was the Pinson Mine, about 13 mi from the proposed plant site. The existing electric line was not capable of carrying another mine the size of Chimney Creek, which required 29 million kwh per year. There were three options available to Gold Fields for the power supply: 1 )Power could be supplied by the public utility from a coal-fired plant about 30 mi away by constructing a new line to the mine,

Jan 1, 1991

By W. Swisterski, G. Romaniszyn, S. A. Lukasiewicz

The present paper analyzes the motion of a particle of material in a horizontaly rotating tumbling mill. The sliding of the particle under action of dynamic and friction forces and its free flight fall are analyzed. It was found that mechanism of free-fall occurs at supercritical rotations of the mill.

Jan 1, 1991

By W. H. Pailes, V. Castranova, K. Van Dyke, J. H. Kang

Recruitment and activation of phagocytic cells after inhalation of occupational dusts has been implicated in the development of pulmonary inflammation, fibrosis, or emphysema. Plateletactivating factor has been described recently as a potent inflammatory agent. The objective of the present study was to investigate if platelet-activating factor might play a role in the inflammatory response of the lung to occupational dusts. In vitro exposure of alveolar macrophages to cotton dust (4 mg/ml), silica (10 mg/ml), or coal dust (10 mg/ml) results in the release of picomole levels of platelet-activating factor with a potency of cotton dust > silica > coal dust. Time course studies indicate that platelet-activating factor release from alveolar macrophages is maximal approximately 10 minutes after in vitro exposure to silica. In vitro, platelet-activating factor is a direct stimulant of polymorphonuclear leukocytes increasing chemiluminescence 2.3 ± 0.3 fold above control. The maximal response occurs in the dose range of 10-10 to 10-7M platelet activating factor. In addition, plateletactivating factor potentiates the response of polymorphonuclear leukocytes to a second stimulant; i.e., chemiluminescence generated from polymorphonuclear leukocytes exposed to plateletactivating factor (10-9M) plus chemotactic peptide (FMLP, 10-9M) is 88 ± 22% greater than the sum of the separate effects of these stimulants. In contrast, platelet-activating factor is not a direct stimulant of alveolar macrophages in vitro, having no stimulatory effect on chemiluminescence or superoxide anion release even at levels of 10-6 to 10-5M platelet-activating factor. However, platelet-activating factor (10-5M) does potentiate zymosan-stimulated activation of chemiluminescence and superoxide release from alveolar macrophages by 117 ± 56% and 30 ± 4%, respectively. In conclusion, these data indicate that exposure of the lung to occupational dusts results in the release of platelet-activating factor which may activate polymorphonuclear leukocytes and potentiate the responsiveness of alveolar macrophages to dust. The net result would be pulmonary inflammation and hypersecretion of reactive species by pulmonary phagocytes which could lead to tissue damage and pulmonary disease.

Jan 1, 1991

By John T. Cantwell

INTRODUCTION The process engineer usually is responsible for the design operating philosophy and/or day-to-day operations of a process. Since instrumentation is an integral part of the operation, it is essential that engineers understand the general capabilities of the different types of control equipment available. Many "noncontrol" engineers have become involved with instrumentation for machinery monitoring and control as well as other plant applications. The advent of the microprocessor has led to significant changes in control, both in systems configurations and man-machine interfaces. Today's concept is called simply "distributed control." What is distributed control? Distributed control is exactly what the name implies; the control system is divided into several functional segments and spread out to cover a process. The systems are distributed for physical, functional, and risk reasons. Before delving further into the specifics of distributed control, let's look at the evolution of control systems to see how we got here. Instruments initially were located near measurement and control points in the field. Operators physically had to go to the instrument to change setpoints or take measurements. As processes became more complex, it became evident that a central control area was required. This allowed an operator to monitor and control many variables. The operator's effectiveness was increased dramatically, which resulted in greater efficiency, better quality control, and lower personnel requirements. At the same time, plants became much larger, control applications became more complex, energy became expensive, and the industry became more competitive. All of these factors placed pressure on process and production engineers to get the most for the money. The result was a continuing push to put more instrumentation into a central control room to maximize efficiency and productivity and minimize manpower. This chapter deals in some detail with devices for measuring physical and chemical properties of coal; devices for measuring the weight and weight-rate of flow of coal; devices for the monitoring and control of conveyor systems, solids inventory, fluid flow, liquid level, density, and specific gravity. These instruments have a multitude of uses throughout a coal preparation plant. The discussions cover advancements in "on-line analysis," nuclear control devices, and distributed control using microprocessors, mainframes, and soft-

Jan 1, 1991

By C. W. Schultz

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained.

Jan 1, 1991

By Jay Hilary Kelley

A ventilation system is described using dual aircourses: one zone occupied by working personnel, the other at the active working face. The two zones are separated by a partition or Shroud. The occupied zone to the rear of the face zone is ventilated adequately but with considerably less air because little gas, dust, or fumes are present. The face excavating zone is sealed and maintained at slightly more negative pressure preventing dust and gas generating from within to escape. Explosive mixtures within the face zone is rendered non-explosive by the introduction of inert gas therein. Each zone is vented separately to the outside of the mine. Because less total quantity of air is required for human breathing, etc, the total ventilation system can be drastically reduced in tan capacity, development entries, and air shafts, -- a great savings in costs.

Jan 1, 1991