Search Documents

By J. R. Woolsey, B. G. Noakes

A prototype remote placer drill (RPD) has been designed and successfully tested in the offshore gold district of Nome, AK. The RPD system is unique in its design and in the cooperative support that was provided during its development by industry, academia and government. The RPD was conceived as a low-cost, rapid drill sampling system for the reconnaissance of marine precious metal placer deposits. The drill functions as a counter- f lush system. It incorporates a dual wall casing and a rotating percussion bit driven by way of a drill rod through the central eductor casing by a heavy duty pneumatic rock drill. The cost of drill sampling in the exploration of marine precious metal placers has traditionally been high due to the technical difficulties imposed by the environment and the remoteness of the sampling target. The objective was to reduce capital and operating costs of a drilling program through the development of a portable system incorporating drill compoments having a high power-weight ratio that could be deployed from work vessels of opportunity. A principal design requirement was to operate the system remotely from the sea floor with only flexible connections to the surface. This includes cable for deployment and retrieval and hoses for air supply and sample recovery, thus making the drill system semi-independent of the vessel's sea-induced motion. The prototype RPD underwent full operational test off Nome, AK in late summer 1988. It was deployed from the landing door of a modified LCT vessel, and rigged for a single pass of 5 m (16.5 ft). More than 50 holes were drilled in a wide variety of bottom materials typical of the off shore Nome submerged beach placers. The prototype RPD proved to be an overall success, recovering representative samples throughout the section in all but the heavy boulder ground. Compared with a conventional drill system on board that was assigned to a production drilling system, the RPD was capable of reliably sampling moderate ground less than 6 m (20 ft) in thickness, using a smaller crew and operating in higher sea conditions.

Jan 1, 1991

By S. Anderson

Advances in inexpensive computer automation led to the development and utilization of a computerized ore control system at Cyprus Coppers tone Gold Mine near Parker, Arizona. These new ore control practices improved accuracy, performance, and productivity of the ore control effort. An automated system for data collection, including bar coding of blast hole samples, laboratory analysis, data management, grade estimation, cut delineation, and ore zone stakeout, plays a major role in ore control practices. This is of particular interest because of the large amount of blast hole information being processed, analyzed, and reported daily.

Jan 1, 1991

By Francis B. Gularte, James E. Monsees, John-Paul Whyte, Gary E. Taylor

In a short section of the Los Angeles Metro Rail system approximately 222.5 m (730 ft) of 6.4 m (21 ft) diameter twin-tube tunnels separated by a 1.8 m (6 ft) narrow pillar were designed to pass under a major eight lane freeway and a metropolitan intersection with only 3.7 m (12 ft) to 5.8 m (19 ft) of loose fill and alluvium cover. The design considerations and the chemical grouting program used to stabilize the alluvial materials is discussed. Also included is a discussion of the novel shield used for tunnel excavation and the effects of the subsequent fire.

Jan 1, 1991

By Perry M. Jones

An important operational and environ-mental concern associated with in situ leaching activity is the balance between solution injection and recovery. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. The Bureau of Mines is investigating the factors that affect solution balance in an unsaturated ore deposit, as part of ongoing in situ leaching hydrologic investigations at the Cyprus Casa Grande Mine. Flow conditions in 58 injection and recovery wells at the Casa Grande In Situ Leaching Test Facility were monitored daily over an 18 month period. Changes in the balance between injection and recovery occurring during this period were evaluated using analytical and statistical methods. The results permit estimation of solution distribution and the volume of solution stored in microfractures and interstitial pore spaces within the deposit following 18 months of leaching. Approximately half of the difference between well injection and well recovery can be accounted for by solution movement through macrofractures into nearby drifts. Estimates of solution storage within the ore deposit at the end of 18 months of leaching range from 3.5 to 6.9 pet. of injected solution. These results also suggest that 13 to 26 pet. of the fracture/interstitial pore space in the deposit was saturated with solution after 18 months of leaching.

Jan 1, 1991

The Coal Utilization review arrived too late to appear in the May issue. Coal utilization technology is improving due to the urgency with the 1990 Clean Air Act and the incentives provided by the Clean Coal Technology (CCT) program. Advances in the CCT are the subject of this report because of their broad industry application, support and involvement. Clean coal demonstration program Projects in the $5 billion Clean Coal Technology program are jointly funded cooperative agreements - not contracts - between government and industry. The industry participant in each project contributes at least 50% of the total cost. The participant takes primary responsibility for the project and is awarded any patent rights for inventions that may occur during the demonstration. The government, on the other hand, ensures that schedules are met, costs are controlled and project objectives are met.

Jan 1, 1991

By A. Vien

MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling development, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law. This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance.

Jan 1, 1991

By J. P. Hedlund

Molycorp's gravity type panel-caving operation employs a system of short raises to transfer ore from the Grizzly Level to the Haulage Level. The raises have normally been developed using a conventional drill-and-blast method or a combination conventional/raiseboring method. A new method was needed that would be less labor intensive, provide a safer work environment for personnel, provide a stable raise that could be self-supporting and a method that would be cost competitive with the conventional system.

Jan 1, 1991

By S. D. Van Nort

Editor’s note: This is the first of two MINING ENGINEERING articles about the Grasberg deposit. The second, focusing on open pit mine development, will appear in the April issue of the magazine. The Grasberg porphyry copper-gold deposit of Freeport Indonesia Inc. lies within the Ertsberg Mineral District in central Irian Jaya, Indonesia. The Grasberg deposit was discovered during a drilling campaign initiated in the mid-1980s. Production at the open pit de- posit commenced in December 1989. The Grasberg copper-gold ore body is contained within a young igneous complex of dioritic composition that intrudes limestones of the Tertiary New Guinea Group. Alteration is typical of porphyry copper deposits worldwide except that higher grade primary chalcopyrite with significant gold values is associated with a centrally located zone of strong quartz stockwork. Irian Jaya comprises the western half of the island of New Guinea. The Ertsberg District lies 70 km (43 miles) inland from the Arafura Sea at an altitudeof3500 to45OOm (11,480to 14,764 ft). It straddles the Papuan fold belt. This belt forms the east-west trending chain of mountains that extend the entire length of New Guinea and is the site of numerous mineral districts.

Jan 1, 1991

By L. A. Taylor

The production of oxygen on the Moon utilizing indigenous materials is paramount to a successful lunar colonization. And several processes have been put forth to accomplish this. The LLOX generation schemes which have received the most study to date are those involving?: 1) the reduction of ilmenite (FeTi03) by H2, C, CO, CH4, CO-CI2, & Cl2 plasma, 2) magma electrolysis, both unadulterated and fluoride-fluxed, and 3) several others, including carbo-chlorination, HF acid leaching, fluorine extraction, magma oxidation, and vapor pyrolysis. The H2 reductions of ilmenite and magma electrolysis processes have received the most study to date. They are both feasible schemes with various pros and cons, including their feedstock requirements. However, all processes should be addressed at least at the onset of our considerations. There is an obvious need for considerably more experimentation and study. Some of these requisite studies are in progress, and this paper reviews several of the most studied and feasible processes for winning oxygen from lunar materials.

Jan 1, 1991

By Raja V. Ramani, Sachin Shankar

Re-entrainment refers to dislodgement of particles deposited by both atmospheric and nonatmospheric processes and their subsequent insertion into a flowing field. Formation of sand dunes, snow drifts, soil erosion and fugitive dust emissions are a few examples of the natural occurrence of re-entrainment. Re-entrainment studies have been done for the estimation of potential hazards from nuclear fallouts. The phenomenon of re-entrainment has been utilized for the cleaning of wafers and filters. Re-entrainment is associated with both surface and underground mining activities. However, studies on dust re-entrainment in mine atmospheres are limited. Understanding the re-entrainment phenomenon is important because dust particles lying seemingly harmless on the ground and adhering to numerous surfaces can get re-entrained and become a health and safety hazard. There are significant differences in the kind of re-entrainment encountered in underground mines and those in other fields of interest. These major differences are air velocity, direction of air flow, particle size, amount of particles, and time of exposure. While numerous studies have been done in other fields to identify the role of interacting variables and their contribution to the mechanisms of re-entrainment, no similar reported work is available for dust in mine atmospheres. In this paper, recent research efforts on re-entrainment are reviewed. The most suitable form of representing re-entrainment in underground coal mine atmosphere is presented. Various approaches to studying re-entrainment phenomenon in mines are also outlined.

Jan 1, 1991

By Randy J. Mikula

Cleaning of low-rank coals can have several meanings, depending upon the definitions of the terms "low rank" and "cleaning." In general, low-rank coals would be lignite or subbituminous according to the ASTM classification. For the purposes of this summary, cleaning is defined to be any process which materially reduces the proportion of inert material in the coal. For low-rank coals, this often means a reduction in moisture content since moisture is the major inert component in these coals. A brief discussion of conventional cleaning processes is included, as is an extensive reference list.

Jan 1, 1991

By Edward F. Divers, J. Drew Potts

Powered dust-filtering helmets (dust helmets) have become increasingly prevalent in the underground mine environment in recent years. Many longwall operations use dust helmets to reduce the respirable dust exposures of miners required to work downwind of crusher, roof support and shearer operations. While continuous mining sections are usually less dusty, use of diesel equipment represents a new potential health problem. The U.S. Bureau of Mines recently conducted a study to determine the efficiency of a dust helmet on diesel-size particulate. Two underground evaluations were conducted on continuous mining sections that were using diesel haulage vehicles. Model No. AH21 Racal airstream helmets equipped with AS22-3 prefilters, AS23-3 main filters and AS60476 tyvek full-face seals were tested. Helmets were placed on mannequin heads and mounted in the ram car cabs. Andersen Model 298 (eight-stage) personal cascade impactors were used to sample air inside and outside of the helmet. Impactor stages 8 and the final filters were analyzed to determine submicrometer (0 - 0.93 µm) particle concentrations. Results from this study showed that the dust helmet was 94% (± 3% at 95% confidence level) efficient on submicrometer particles. Typically, very little coal dust is observed in the submicrometer size range, therefore, these particles were assumed to be from diesel exhaust. Results from this study indicate that proper use of the dust helmet on continuous mining sections that are using diesel haulage vehicles may be beneficial to the health of miners.

Jan 1, 1991

By Yu Qixiang, Wu Yanyun, Guo Junfeng

The experience of mining coal and gas outburstprone coal seams shows that the degree of outburst danger in various coal seams and even at different parts of the same seam are quite different, and that to deal with them respectively in different ways will not noly be significant to safety but bring us remarkable economical profit, Based on the statistical data,including elght static and dynamic factors, gathered from coal and gas outburst spots at Nantong colliery in Chong Qing district of China, this paper has partitioned the degree of outburst danger of the No. 5 seam there by means of Fuzzy Clustering method. Because in the evaluation multiple indices have been considered, the result of partitioning is identical to practice and more efficient in applications.

Jan 1, 1991

By Richard B. Muter

In determining the layout or combination of unit operations to be utilized in a modem preparation plant, several factors must be taken into account. Among these are the washability data, size consist data, the particular market or markets for the coal, the mining method used, the degree to which the coal must be prepared, expected fluctuations in raw coal and markets, and the overall economics of the process. In addition, there are the health and safety aspects of coal utilization and preparation. Chapter 1 of this book discusses the characteristics of coal and coal markets, while Chapter 2 deals with the design of preparation plants. Once the unit operations for a particular plant have been decided upon, these arrangement may be depicted by using a flowsheet. A coal preparation plant flowsheet is a two-dimensional graphical representation of the sequence of operations, the arrangement of machinery, and the flow of materials for a particular coal cleaning operation. The flowsheet is usually qualitative in nature, becoming more quantitative as material balances, water balances, numbers and sizes of various pieces of equipment, etc. are added. The usual convention in preparing a flowsheet is to show the feed flowing from left to right, starting at the top left and working down as in an all-gravity process. Various symbols are used for each unit operation as depicted on a flowsheet, and Fig. 14-37 is a compilation of the commonly accepted international standard symbols for each unit operation. Fig. 14-38 through Fig. 14-40 are flowsheets of various coal cleaning processes as published in the January 1976 issue of Coal Age. Each process has its own unique features which, among others, depend upon the coal being cleaned, the coal market, and the mining operation. Fig. 14-38, for example, is a flow diagram for a jig plant preparing steam coal from two strip mines located a few miles apart. In addition to the jig washer, cyclones are used to treat the finer size coal. Fig. 14-39 is a flowsheet of a heavy media plant using a heavy media washer for + %-in. (+6.3-mm) coal, froth flotation for -28 Tyler mesh (-0.6 mm) material, and dewatering phase units (dwp) for Y, in. x 28 Tyler mesh (6.3 x 0.6-mm) cleaning of steam coal. In addition, thermal drying, centrifuge drying, and the use of vacuum disk filters and thickeners for dewatering are depicted. Fig. 14-40 is a flowsheet of a plant producing metallurgical coal. In addition to the heavy media and froth flotation circuits, a tabling circuit is also employed. These flowsheets are intended to give the reader an example of how the various unit operations for coal cleaning may be linked together. Figs. 14-41 and 14-42 illustrate the conversion of block diagrams into an IS0 prescribed set of symbols.

Jan 1, 1991

By Guillermo P. Salas

The Consejo de Recursos Naturales No Renovables of the Mexican government entered into an agreement with the United Nations in 1964 for the mineral exploration of a large area in Estado de Sonora, Mexico. The agreement called for a systematic exploration for copper in northern Sonora based on photogeologic mapping, aerial reconnaissance, and geochemical stream sediment sampling. The UN-CRNNR investigations resulted in the detection of anomalous copper values in sediment from the Arroyo Cruz de Cafiada. The anomaly was followed upstream to its source, which ultimately proved to be the La Caridad ore body (see Fig. 1). Soil copper and molybdenum values were found over a large area, and further detailed geologic and geophysical investigations were instituted of the anomalous area. David Coolbaugh was largely responsible for the follow-up work. An induced polarization (IP) survey found a roughly circular region of "highs" that coincided with a high soil copper anomaly. The circular anomalies ringed the topographic feature that ultimately was found to contain the Caridad ore body. Soil geochemical copper response over the ore body was subdued, because the soils were derived from a leached capping, whereas leaching in fringe areas that contained less veining was less intense. The ore body was also ringed by the typical high pyrite zone, and this was the anomaly detected by the IP survey. The UN began drilling in the fall of 1966. Eleven holes tested the IP-Cu geochemical high, but none were of commercial interest. The project was returned to the Consejo and was reviewed in the field by G.P. Salas and V.F. Hollister. It was found that the leached capping had not been tested by the past activities, and the Consejo elected to explore that area in 1967. The capping was evaluated by Salas and Hollister and drilling by the Consejo began in 1967. Commercial grade ore intercepts were found in the first hole. The Consejo drilled nine holes, of which eight were commercial. At least 90.7 Mt (100 million tons) of 0.8% copper were indicated by the Consejo in eight holes. The lesson learned in this discovery is that evaluation of leached capping is an important guide to exploration. The general-

Jan 1, 1991

By W. K. Connor, O&apos

The Bureau of Mines is investigating the Co and Mn resource of the West-Central Arkansas District, including field investigations, mineralogical characterization, beneficiation, and hydrometallurgical tests. The deposits occur within the Ouachita Mountains and are con-trolled structurally, occurring along the axes of anticlines making up the mountain ridges. Brecciated novaculite is cemented with a mixture of Mn oxides, primarily cryptomelane and psilome-lane. Cobalt is concentrated within a particular Mn oxide phase, lithiophorite. Chemical analyses on head samples reported up to 25 pct Mn and 0.17 pct Co. Magnetic separation yielded products with up to 41 pct Mn and 0.22 pct Co at recoveries of 95 pct Mn and 93 pct Co.

Jan 1, 1991

By D. K. Steele

The U.S. Bureau of Mines has investigated the recovery of metals from copper industry wastes by sulfuric acid leaching in a semi-continuous, bench-scale system to solubilize arsenic, copper, and molybdenum. Leach residues contained approximately 40 wt pct PbSO4, suitable for processing at a lead smelter. Arsenic and molybdenum removal from leach solution was examined using solvent extraction with tri-n-butyl-phosphate (TBP), and copper was subsequently recovered by cementation. Bleed electrolyte from a copper refinery was determined to be a viable source of acid for the initial leach stage.

Jan 1, 1991

By Keith G. Wallace, Malcolm J. McPherson

In order to model accurately a mine ventilation system in an existing mine, it is necessary to determine the resistance to airflow in all main airways. This is accomplished by measuring the airflow and pressure differential in each airway. Gauge and tube methods have been used to determine pressure drops in ramps and level airways. However, it has rarely been used in evaluating the frictional pressure drop in shafts. Because shafts commonly have the highest pressure loss in mines, it is critical that the resistance of these airways be determined accurately. This paper describes the theory and practice of using the gauge and tube method for determining the pressure drop in shafts. The pros and cons of using this method are discussed as well as a comparison between the gauge and tube and barometer measurement techniques. Case studies showing the accuracy of shaft gauge and tube measurements are also presented.

Jan 1, 1991

By Leonard W. III Joseph, William H. Buttermore

Noise control is an important consideration in the design and operation of coal preparation plants. It is essential to understand and control noise sources to provide a safe environment for operating personnel. The average noise exposure levels in a typical coal preparation plant generally range between 95 and 100 db. An operator should not be exposed to noise levels of this magnitude for more than 4 and 2 hr, respectively, according to MSHA (Mine Safety and Health Administration) regulations. The major noise sources in a coal preparation plant include noise from impacting the inside surfaces of steel chutes, vibrating screens, coal crushers, pumps, motors, fans, and blowers. The magnitude of noise varies considerably from one situation to another. NOISE EXPOSURE IN COAL PREPARATION PLANTS Noise regulations established by the Occupational Safety and Health and- ministration (OSHA) are accepted by MSHA relative to coal preparation plants. Fig. 14-43 shows a graph of the time of noise exposure in hours per day to which a worker can be exposed for each A-weighted sound level. According to this graph, a worker is permitted to spend 8 hr in a 90-db noise environment, but that time must be halved when the A-weighted sound level increases 5 db. The noise dosage a worker receives is determined by the ratio of the length of time the worker spends in a particular noise environment divided by the length of time he is permitted to spend in that environment. If the worker is exposed to several different sound levels, his total dosage would be the sum of each of the individual dosages. The equation for determining the dosage is: where C is the actual duration of exposure at a given steady state noise level and T is the noise exposure limit for the level present during the time C According to MSHA regulations, the dosage, D, should not exceed one (1) for any worker for a full day of work. As an example of typical plant noise levels, vibratory screens and crushers emanate noise levels in excess of 90 db at a distance of 3 ft (0.9 m) with no material flow. With material flow, noise level increases 1 to 10 db depending

Jan 1, 1991

By Leo Misagi

THE ROLE OF MANAGEMENT IN PLANT SAFETY Safe Production In plant management, safe production is an ideal. It becomes reality when: 1. Plant employees work in healthful and safe conditions. 2. Plant safety is in harmony with productivity. 3. Worker absenteeism and turnover are low-the work force is stable. Plant management must apply its talents, skills, and resources to build and maintain the foundations of safe production on a system of policies, procedures, and attitudes. It must do so by marshaling all managerial functions - staffing, direction, control, innovation, and representation-toward that goal. Ideally, a plant safety program is proactive. Management should plan and implement safety activities that are aimed at prevention. Past accidents-accomplished facts-should not be the sole guide of future actions. In other words, positive preventive measures, not the fewness of accidents are the criteria for safety production. An ideal safety program is one which is cost effective. Management should view plant safety as part of a broader program-loss control. Loss control includes prevention of fires and other accidents, unhealthful conditions, and occurrences that cause bodily injury, illness, property loss, or damage. Management evaluates the employees' productivity and safety. An effective training program aimed at loss control is the hallmark of safe production. Ideally, both labor and management should be well versed in safety. They believe in the premise that work-related injury and illness, as well as property loss and damage from fire and other accidents, are manageable and preventable. Such belief prompts them to learn more about the work process and potential hazards associated with each job. They also learn how to expect and prevent fues and other accidents, and respond to emergencies at the plant. Plant management determines which individuals or groups of employees are accountable for the following functions:

Jan 1, 1991