Search Documents

By Steve Lloyd, Mary Anne Antonioli, Byron Darnton

The Pegasus Gold/Montana Tunnels Mine is a high­tonnage, low-grade, base and precious metal operation in Jefferson City, Montana. Gold heads are typically 0.02 opt with the dominant gold mineral being a native metal electrum quite rich in silver. Early research and development indicated the ore to be amenable to gravity concentration at a 10 to 14 mesh grind. Although full flow gravity preconcentration was considered as a flowsheet alternative, flotation was chosen as the main recovery process due to its apparent lower cost for capital and operating. At this early juncture, the option or concept of recovering coarse free gold by gravity was deemed unnecessary or irrelevant. The intermittent loss of free gold has been observed in the flotation tailing since mill start up. A comprehensive research program was initiated in 1990 to identify the magnitude of this loss and investigate alternatives for its recovery. Batch and pilot plant testing has ultimately led to a permanent gravity circuit being installed at the cyclone underflow. The circuit is designed to scalp out the liberated coarse gold contained in the ball mill circulating load. The final flowsheet consists of: a pinched sluice to upgrade cyclone underflow; a Tyler doubledeck screen to remove over­size from sluice concentrate; Knelson concentrators for roughing and cleaning of screen undersize; an Eriez wet drum separator to remove tramp metal from Knelson concentrate; a Sweco screen to size Knelson cleaner concentrate for tabling; and a Wilfley table to produce final concentrate for direct melting.

Jan 1, 1992

By Laura L. Damon, Alastair McNeillie

The use of calcium peroxide for enhanced heap detoxification has been investigated on the laboratory scale using heap leach columns. The addition of calcium peroxide to the ore prior to leaching resulted in a significant increase in the rate at which the leached ore was detoxified and this led to an overall decrease in the total heap leach cycle time. This decrease could allow a minesite to increase the ore throughput or gold leaching time and generate additional revenue. The process is of particular relevance to reuseable leach pad operating though pennanent pad systems could also benefit.

Jan 1, 1992

By Matthew J. Hrebar

A comparison of hydraulic shovels (HS) versus front-end loaders (FEL) is commonly made when an excavator with some degree of mobility and medium reach is required. These applications are often found in hard rock open pit and surface coal mining applications, among others. The purpose of this paper is to present a comparative economic study of the two excavators. Production data was collected from both HS and FEL manufacturers as well as operating mines. Availability, operating costs, and estimated operating life were gathered from operating mines, while capital costs were obtained from manufacturers. The data was limited to studies and operations which included both types of mid-size excavators. The economic study is followed by a discussion of other factors considered by mine operators in excavator selection. The study was originally made for a presentation at the 23rd Intermountain Minerals Conference at Vail, CO.

Jan 1, 1992

By Vernon F. Swanson

The expansion of a fluidized bed of carbon depends on fluid velocity, fluid temperature (viscosity) and particle size of the carbon. This paper presents a mathematical model which can be used to calculate the necessary fluid velocity. It will allow the design of sufficient freeboard in the column to accommodate expected operating conditions. Although this paper is keyed towards the use of activated carbon in precious metals adsorbtion from water solutions, the model is.valid with any fluid. Additionally, the method of calculating the required suspension velocity in CIL or CIP pulps is described.

Jan 1, 1992

By Julia R. Budden, Peter A. Spencer

Bacterial oxidation processes have often been repo1ted as releasing large amounts of energy so that a large scale operation would require cooling to maintain the required operating temperature for the bacterial culture. These reports are based on the chemical heat release which in some eases has been adjusted for the energy required to fonn the mass of bacterial cell matter per unit volume of solution. There are two flaws in this approach for calculating energy release in the fonn of heat. The first flaw is that it only considers the bacteria in solution. The second assumption is that the only bacterial reaction is the fonnation of cell material and others such as energy for respiration and locomotion are not considered.

Jan 1, 1992

By John O. Marsden

Process selection is the systematic development of the optun.m metal extraction route for a particular feed matenal and has two main objectives: (1) to optimize project economics, principally a function of gold recovery, throughput rate and processing costs, and to develop a process that satisfies all of the proct requirements including, for example, political and environmental considerations.

Jan 1, 1992

By J. S. McAlpine, J. Matousek, W. Muir, P. Downey, K. Major

The Golden Bear refractory gold ore roasting operation is located at Huddy Lake, in northwestern British Columbia, about BO km northwest of Telegraph Creek (see Figure 1). The mine access road, used for supplies delivery, was developed by Golden Bear and consists of a radio controlled 155 km gravel road originating at Highway 114. Hine operations are based on a two week in, two week out rotating shift schedule with personnel transport by chartered aircraft from Vancouver, Whitehorse or the 3 Talthan conmunities. The site runway Is located adjacent to the tailings impoundment.

Jan 1, 1992

By W. J. Garmoe

The Carr Fork mine is located approximately 50 kilometers southwest of Salt Lake City, Utah, in the Bingham or West Mountain District, adjacent to the Bingham open pit copper mine. Applied geology at Carr Fork, by Anaconda Minerals Company personnel, includes detailed geologic mapping and sampling of underground workings, logging and sampling of drill core and cuttings, and the preparation and posting of geologic maps and cross sections for geologic interpretation, ore reserve calculation, mine operations, and long range planning. Accurate and easily understood graphic recording of Carr Fork geology is essential for optimum use by operating and engineering personnel. The design and implementation of exploration, development and definition drilling programs, research into geological spatial relationships, and analysis of structural complexities of the Carr Fork deposit are also integral parts of the applied geology program.

Jan 1, 1992

By W. J. McDonough

Rapid growth and acceptance of engineered materials have changed the way we live. We have come to expect improved performance at less cost. At the same time, our awareness of societal and environmental issues created by these materials during and after their lifetime has been heightened. As a result, material lifecycle analysis is receiving considerable attention. Material lifecycle analysis evaluates the cost/effective tradeoffs at each stage of a material's life: feedstock, fabrication, performance, recycle, and disposal. The U.S. Bureau of Mines investigates a material's lifecycle using technical cost models augmented with decision and impact analyses. Results of these studies are useful in gaining a better understanding of current material selections and illustrating the multifaceted issues associated with engineered materials in today's society.

Jan 1, 1992

By Jeffery Denit, Steve Hoffman, Van Housman

The Environmental Protection Agency (EPA) is in the early stages of developing a national mining waste program. Our goal is to develop a mining waste program that will be state implemented, multimedia in nature, flexible, utilize and enhance existing state programs, and protect the environment. The Agency appreciates the cooperation the mining industry is providing through its participation in the Policy Dialogue committee on Mining and by providing the Agency with technical data. The following is a discussion of what led to the development of a national mining waste program, the agenda initiative to evaluate Toxic Substances Control Act authority in phosphate manufacturing, and the important steps being taken through the Policy Dialogue process to frame and discuss issues. EXTRACTION AND BENEFICIATION OF ORES The Resource Conservation and Recovery Act of 1976 (RCRA) and subsequent amendments created a framework for the regulation of hazardous wastes under Subtitle C and nonhazardous waste under Subtitle D. In 1978, initial regulations were proposed for hazardous waste management units under RCRA. These identified a universe of special wastes that were large volume, low hazard and less amenable to Subtitle C control techniques. EPA noted that waste materials from the "extraction, beneficiation and processing of ores and minerals m fit these criteria. In October 1980, Section 3001 of RCRA was amended. This Bevill amendment excluded solid waste from the extraction, beneficiation and processing of ores and minerals from regulatory control under RCRA's hazardous waste Subtitle C. This was done pending a report to Congress and a regulatory determination regarding the Subtitle C status of these wastes. Thus in November 1980, EPA published an interim final amendment to the RCRA Subtitle C regulations to reflect the Bevill amendment. RCRA requires EPA to perform studies and make reports to Congress regarding the management methods and potential hazards of managing waste. RCRA also calls for a regulatory determination regarding whether Subtitle C (hazardous) or D (non- hazardous) controls are warranted for these wastes. In December 1985, EPA submitted a report to congress entitled, “Wastes from the Extraction and Beneficiation of Metallic Ores, Phosphate Rock, Asbestos, Overburden from Uranium Mining and Oil Shale." In that report, EPA found that some mining wastes exhibit hazardous characteristics, that the range of risk from mining waste is broad, and that waste management practices have caused environmental damage. In July 1986, EPA published a regulatory determination based on information gathered in the 1985 report to Congress and comments from interested parties. In the report, EPA concluded that RCRA Subtitle C regulation of extraction and beneficiation wastes was unwarranted because mining wastes tend to be disposed of in arid climates, waste volumes are high, and facilities and wastes are located in sparsely

Jan 1, 1992

By M. S. Klima

This paper will detail the work that has been done in 1990 and 1991 at the Pittsburgh Energy Technology Center (PETC) on the development of the U.S. Department of Energy's (DOE) patented Micro-Mag Process. This process entails the use of a micronized-magnetite (minus-10 microns) and water mixture for cleaning fine coal (minus-600 microns) in a cyclone, along with the production and recovery of the magnetite. Emphasis will be on the results from micronized-magnetite recovery testing using both conventional wet-drum and high-gradient magnetic separators in which several key operating conditions were varied including feed percent solids, magnetite-to-coal ratio, magnetite grade, and feed rate. Also presented will be selected results from testing done on a 76-mm diameter cyclone at a relative density of 1.50 showing the effects of operating pressure, magnetite grade, and medium-to-coal ratio on separation efficiency. In addition, two methods for producing micronized magnetite, along with the corresponding size distributions, will also be discussed.

Jan 1, 1992

By J. Fuchs

This paper describes the mechanized narrow vein cut-and-fill approach used for the Deep Copper orebody at Falconbridge Limited's Strathcona Mine. Strategies for achieving high productivity while maintaining ground stability at depth and controlling dilution are discussed, including the use of mini-electrohydraulic drilling equipment, containerized truck haulage, consolidated rockfill placement techniques, and a miners' incentive system.

Jan 1, 1992

By J. J. Sammarco

Computer-aided control of a mining machine pl aces its operator in a safe, remote location, thus reducing health and safety risks, Sensing systems that provide machine position (xy coordinate) and heading (yaw), are extremely useful in aiding remote positioning of mining machines. The U. S. Bureau of Mines has developed two sensing systems for position and heading information: A scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system that employs ring-laser gyroscopes. This paper presents a brief background and status of these sensing systems as applied to the remote positioning tasks of a continuous mining machine. Included are field test results of each system operating in a room-and-pillar research section at a cooperating mine in West Virginia.

Jan 1, 1992

By R. A. Metz, Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon 'Yankee Ingenuity,' innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1992

By Van E. Housman, Stephen D. Hoffman

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), also known as "Superfund", requires a listing of sites that have known releases or threatened releases of hazardous substances, pollutants, or contaminants throughout the U.S. When EPA determines that a significant threat exists, it places the worst contaminated sites on the National Priorities List (NPL). CERCLA provides EPA broad authority to clean up hazardous sites that threaten human health and the environment. There are currently 52 sites on the NPL that were placed on the list because of high human health or environmental risk as a result of non-coal mineral extraction, beneficiation, or processing operations. This list covers mining sectors from aluminum to zinc. While some of these sites were abandoned, many are still operating. (There are additional mine sites that have been recently proposed to be included on the NPL that are not included in this paper.) EPA is continuing to develop a mining program to address human health and environmental threats from active non-coal mines. EPA has performed a comprehensive study to assess the waste management practices at all of the 52 mine sites on the NPL. In addition, EPA is continuing to collect information on the specific mining sectors (i.e., gold, copper) that represent many of the NPL mine sites. One of the goals of this effort is to attempt to identify the types of mining practices that lead to human health and environmental problems at the NPL mine site. EPA estimates that there are currently 500 to 1,000 active mines (not including placer operations). While some mining NPL sites began operations before the turn of the century, only a handful of the NPL mines entirely ceased operations prior to 1970. Of the 52 NPL sites studied by EPA, 12 are currently active. By definition, these mines represent current mining practices. Approximately 17 additional NPL mines that ceased operations between 1970 and 1990 represent some degree of current mining practices. Therefore, at best, less than half on the 52 NPL mine sites can be said to definitely represent past mining practices. Although some mining waste management practices have changed over time, the basic technology for extraction and beneficiation of mineral ores have remained fairly constant over the last fifty years. While the use of acid to leach copper dumps, the use of cyanide to leach gold in heaps, and the spread of solvent extraction techniques has changed some aspects of mining, the basic operation of removing ore from the ground and concentrating it through beneficiation has remained fundamentally the same as when most of the non-active

Jan 1, 1992

By D. C. Shumway

Mining in Cushenbury Canyon began in 1860 when John Cushenbury left his Holcomb Valley gold prospect and discovered a silver vein in the limestones of the present day Cushenbury Mine. Cushenbury Canyon is located along the western boundary of the Mojave Desert in Southern California and on the north slope of the San Bernardino Mountains. The Holcomb Valley, immediately southeast of Cushenbury Canyon was the most prolific gold producer in Southern California. Gold mining dominated the area until World War II when interest in the Lucerne Valley Limestone deposits was peaked by the construction of the Kaiser Steel Plant in Fontana, California. The steel making process required large amounts of metallurgical grade limestone and Kaiser geologists located claims in most of the limestone deposits. Kaiser Cement constructed a cement plant and limestone mine in Cushenbury Canyon in 1956. Kaiser Cement modernized the facility in 1982 to a four stage preheater-precalciner system. Mitsubishi Cement Corp. purchased the property in April, 1988, and through further system modifications have created the most efficient and modern cement plant in the United States.

Jan 1, 1992

By P. M. Pettit

Hydrologic investigations at Gold Quarry began in 1989 and continued through 1991. Hydro-stratigraphic units include Tertiary sedimentary rocks, Paleozoic siltstones and carbonates. These units display complex and variable aquifer parameters as a function of faulting and hydrothermal alteration, creating compartmentalized hydrologic domains. Testing has included step-tests, spinner production logs and constant discharge tests. Two Three-Dimensional Finite Element Models have been developed, one for optimizing the pit dewatering system and the second for predicting regional impacts of dewatering. Aquifer testing and long term pumping have been used to calibrate both Finite Element Models.

Jan 1, 1992

By T. J. Haddon

For the mining industry in general and gold mining in particular the past few years have been difficult. Economic conditions coupled with growing regulatory restrictions have led to increasingly important reasons for managing assets wisely. From a public company perspective this makes sense because it ultimately provides for an increase in shareholder wealth and that's what we're in business to do. Regardless of whether a company is public or not, assets must be managed effectively to remain a player in today's competitive environment. So, as the CEO of a gold mining company, how do we manage our assets to ensure that we are satisfying our obligations to our customer --the Amax: Gold shareholder? Let me tell you. As I said earlier, the gold industry has been under siege. We have just completed our third year of average prices below $400 per ounce. When you add finding and/ or acquisition costs and development costs to operating costs, there isn't much of a profit margin left. What this environment provides, however, is opportunities for growth. In the gold business, you either grow or you die. Today, most North American gold producers have at most a 10 year mine life. We are all scrambling to add reserves so we don't become extinct. As prices remain low, opportunities for increasing diminishing reserves abound. This is the time for the opportunistic company to take advantages of market conditions and that's precisely what we, at Amax: Gold, have done!

Jan 1, 1992

By R. J. Reuss

The ore at this new underground operation is a massive sulfide breccia with high copper values. A major highway and electric transmission line pass directly over the near-surface orebodv. The mining method being used is undercut and fill. A continuous miner together with a single boom, hydraulic jumbo is used for the mining. Backfill is a weakly cemented sand-gravel mixture that is pneumatically placed. The ore is treated by conventional crushing, milling and flotation.

Jan 1, 1992

By J. C. Heter

The P.W. Gillibrand Company has been processing and stockpiling a suite of heavy minerals at its Soledad Canyon Mine as co-products with construction aggregates since 1984. The heavy minerals are composed of ilmenite, magnetitie, apatite and zircon. The source of the heavy minerals is the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. The valuable minerals are readily amenable to standard ore dressing techniques, such as, gravity, magnetic, flotation and electrostatic separation with good recovery and product quality. More than 20,000 short tons of coarse ilmenite were sold in 1990 to the export market for titanium pigment production.

Jan 1, 1992