Search Documents

By Thomas R. Yanske, Jonathan E. Carmack, Lyndon M. Clark

In order to maximize the extraction of high grade pillars at The Doe Run Company, artificial pillars are created using cemented rock fill (CRF). CRF pillars aid extraction of pillars in two ways. One is to offer back support for the immediate area where pillars are being extracted. The second is to increase the post failure residual strength of pillars surrounded by backfill. The CRF is produced using a combination of minus 1.0 m run of mine (ROM) rock and minus 5 cm crushed rock. Depending on the operation the CRF slurry is either produced in an underground or a surface batch plant. The slurry and rock are transported to the fill area by truck where they are mixed and placed in 1 m lifts. To reduce the amount of CRF needed, fill fences are constructed around the perimeter of the CRF pillar. Within these fences ROM CRF is placed in lifts until within 0.6 m of the back after which minus five centimeter CRF is slung tight to the back utilizing slinger trucks. In constructing these artificial pillars a number of set procedures have been established to ensure that the work is done both properly and safely.

Jan 1, 2001

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies key problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2001

By R. D. Hagni, P. A. Shivdasan

Cathodoluminescence microscopy (CLM) is uniquely applicable to the study of carbonatite-related fluorspar ore deposits. The mineralogy of the carbonatites, sodic and potassic fenites, marbles, quartzites, and fluorite ores are readily determined and characterized. Calcite, dolomite, apatite, fluorite were deposited dominantly under high temperature conditions and they exhibit strong cathodoluminescence (CL). Three types of carbonatites have been recognized at the Okorusu, Namibia carbonatite complex and fluorspar mines by field mapping and laboratory CLM. The main carbonatite intrusion is fine grained and consists mainly of calcite. A later phase of pegmatitic carbonatite consists of calcite, magnetite, Fe-rich pyroxene, apatite, and pyrochlore. Pyroxene carbonatites were recognized mainly through their study by CLM.

Jan 1, 2001

By Bryce T. Tripp

Utah produces a wide variety of industrial rock and mineral commodities, valued in 1998 at $534 million (28 percent of the total non-fuel mineral production of Utah). Major commodities produced in 1998 include: halite; potash and magnesium chloride; Portland cement; sand and gravel; car- bonates including lime, limestone, and dolomite; phosphate; crushed stone; clays; perlite; gypsum; and sulfur and sulfuric acid. Commodities produced in lesser amounts include: diatomite; pumice; silica; lightweight aggregate; gemstones, ornamental stone, and mineral and fossil specimens; byproduct sulfur and sulfuric acid; silica; and building stone. The years 1993 through 1998 were a period of steady growth in industrial rock and mineral production. However, some commodities have grown much more rapidly than others. The robust western U.S. economy has stimulated production of construction-related commodities like sand and gravel, raw materials for Portland cement, lime, and building stone, resulting in exploration for raw materials, development of new quarries, and expansion of existing plants. Noteworthy specific developments include: (1) opening of new aggregate operations and buyouts of small aggregate operations by large national and international firms, (2) expansion of a lime operation and two cement plants, and (3) development of several new gypsum mines. The future of the industrial minerals industry in Utah looks promising despite a more restrictive regulatory environment and a growing anti-development attitude among its citizens. While Utah has become less pro-development than it was prior to the 1990s, it is still moderate compared to strongly anti-development states, so companies have some motivation to choose Utah in their strategic mineral development plans. As long as the western states' economies continue to grow, Utah's industrial minerals industry should thrive.

Jan 1, 2001

By James P. Cooney

The global mining industry is in the process of redefining its activity and purpose in terms of sustainable development. This process is impelling a growing number of companies to engage their stakeholders on environmental and social issues. Nongovernmental organizations (NGOs) have customarily acted as critics of the mining industry's performance. A new relationship between mining companies and NGOs is emerging in the context of sustainable development, ranging from dialogue to joint action. If positive interaction among mining companies and NGOs is to succeed, clear terms of engagement must be articulated, and measurable progress toward achieving both corporate and NW objectives must be demonstrated. The experience of Placer Dome is illustrative of the rewards and challenges of engaging with NGOs.

Jan 1, 2001

By B. S. Pierce

The National Coal Resource Assessment – 2000 project was a multi-year effort by the U.S. Geological Survey to identify, characterize, and assess the coal resources that will supply a major part of the Nation’s energy needs during the 21st century. The purpose of the USGS National Coal Resource Assessment (NCRA) was to (1) digitally assess selected coal beds and zones that will be the most important in the next few decades, (2) create publically available stratigraphic, geochemical, and geographic information system (GIS) databases to answer a variety of questions of importance to government, industry and public decision makers, and (3) provide interpretive geologic and geochemical information for the primary coal resources of the Nation. Five priority regions were assessed: the Appalachian Basin, Illinois Basin, Gulf Coast, Illinois Basin, and Northern Rocky Mountains and Great Plains. The NCRA was a cooperative effort between the USGS and a number of State geological surveys in these coal-bearing regions. A study of coal resources on Federal lands was also conducted. Adequate energy supplies and the efficient use of those supplies are critical to the economic well being of a country. Affordable and reliable coal supplies are essential to the interests of our national and local policymakers. Policy makers require a range of information on the energy supply, as well as the economic and environmental issues associated with that energy source and its use. Formulation of an effective national energy policy and development of energy resources requires that we understand the geology, distribution, quality, and size of the national energy endowment.

Jan 1, 2001

By Edgardo Fogli, Mario Lampiano, Antonio Nicola

The project is located in the northern region of the People’s Republic of China and was awarded to Impregilo, as sponsor of the Wan Long Joint Venture, in September1997. The project consists of four tunnels for a total length of 88,700 m, with an excavation diameter of about 4.9 m. The lining is made of honeycomb pre-cast segments, connected by PVC dowels and the joints are sealed with elastomeric gaskets. The geology is mainly Limestone, Dolomite and Sandstone. Karst cavities are abundant and are often in-filled with plastic red clay. This has adversely affected the TBM’s progress. Four double shield telescopic TBMs were mobilized to cope with the very tight construction schedule and, at the end of November 2000, more than 80% of the tunnel has been bored. The article analyses the TBMs’ productions in the various geological conditions and the results of different technical solutions adopted at the project.

Jan 1, 2001

By H. Reed

The precious metal mining industry in Nevada handles and generates a certain amount of hazardous materials and waste on a regular basis. These products range from processing material additives to wastes from laboratory testing, heap leaching, and hydrocarbon treatment and disposal. The volume of materials and wastes is dependent upon the amount of ore processed. Handling, treatment and disposal is dependent on the type of material handled and the waste generated. Owing to the health and safety concerns and due to the existing regulations that control handling and disposal of hazardous materials and wastes, the mining industry is obligated to comply with all applicable requirements for proper handling of these products. Plus, in an effort to minimize any impacts from this effort, the industry is continually looking for alternative methods to accomplish these requirements and to also minimize costs. This paper will discuss the general, and in some cases the specific conditions, by which the industry is coping with the issue and efforts to minimize any impacts from handling, treatment and disposal for hazardous materials and wastes. The subject of compliance with the Toxic Release Inventory (TRI) requirements and bio-treatment of wastes and other technologies will be discussed.

Jan 1, 2001

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90-wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct resulting in attempts for magnetic separation. These separations are desirable in the notion that there is no waste product generated from this type of processing and consequently an opportunity for complete utilization of the waste material. Conversely, the pre-separated material could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Critical assessment of the recovery sequence chosen for the products has been described based on economics.

Jan 1, 2001

By Steven W. Hunt, Gregory C. Baker, Glen J. Rorison

Microtunneling methods were utilized beneath pile-supported clarifier basins to replace settlement damaged sludge drain lines at the Jones Island Wastewater Treatment Plant in Milwaukee, Wisconsin. To minimize the risk of blockage and expensive recovery of a microtunnel boring machine against pipe piles or construction debris, a Soltau RVS 80 was utilized. This machine allowed the alignment to be initially bored with guided 114-mm diameter rods to ensure proper alignment and lack of obstructions. Casing pipe was then installed by jacking 1-m long, 305-mm diameterclay pipe along the rods and behind an auger head. This case history also discusses how 2.4-m diameter precast concrete pipe was used as a one-pass sinking caisson for workshafts and new cleanout manholes.

Jan 1, 2001

By Steve Klein

Weak rock is an important consideration in tunnel design and construction due to the difficult ground conditions that are often encountered. Nevertheless, when conditions are favorable high advance rates can be achieved leading to economical tunnel construction. Successful construction of a tunnel in weak rocks depends on correctly anticipating the behavior of these unique materials. The objective of this paper is to provide guidelines that can be used to accurately classify the performance of weak rock in tunnels.

Jan 1, 2001

By I. Yildirim

Water contact angles of talc powders were determined from the values of the heats of immersion measured using a flow microcalorimeter. The results were used to calculate the contact angles using a rigorous thermodynamic relation. In the present work, the calculation was carried out using the temperature coefficient of the contact angles determined experimentally using another method. The results obtained in the present work on several different talc samples are compared with those obtained using other methods.

Jan 1, 2001

By Michael F. Tucker

Dealing successfully with intercultural issues is critical for success on an international assignment. This is true not only for employees but for the accompanying spouses and children as well. This paper presents a set of research-based competencies required for successful life and work in another country, such as open-mindedness, flexibility, and respect for the beliefs of others. Best practices for training employees and their families bound for international assignments are also presented.

Jan 1, 2001

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well approved Tunnel Seismic Prediction System (TSP) has been substantially enhanced for online geological prognosis in underground construction. The method provides high resolution seismic images of the rock mass ahead of a tunnel face via an array of standard anchor rods. These contain3D-geophones and can routinely be installed during the excavation process. A further outstanding feature of the system is the newly developed high frequency repetitive seismic source which can easily be fixed at a tunnel boring machine. A user-friendly software package enables online data acquisition, processing, 3D-visualization, and interpretation.

Jan 1, 2001

PolyMet Mining is developing the NorthMet property near Duluth, Minnesota. Laboratory investigations had led to the development of the PLATSOL process to dissolve in one step the base metals (copper and nickel) as well as the gold and PGM’s. To complete the pre-feasibility study, a fully integrated ten-day pilot plant trial was undertaken, comprising of: high temperature (>220ºC) pressure oxidation in the presence of 5-10 g/L chloride (the PLATSOL process), followed by solid/liquid separation, gold plus PGM’s recovery from solution, conventional Cu SX/EW and recycling of the copper raffinate to the autoclave. The concentrate tested was a NorthMet bulk flotation concentrate assaying 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t Au, 2.2 g/t Pt and 9.9 g/t Pd. Laboratory results were fully confirmed and with minor adjustments of the laboratory PLATSOL® conditions, the following leach extractions were obtained during the pilot plant trial: Cu 99.6%, Ni 98.9%, Co 96%, Pd 94.6%, Pt 96% and Au 89.4%.

Jan 1, 2001

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent upon the application, mineral properties and available instruments. Different instruments produce images that display different features; in order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application.

Jan 1, 2001

By Robert J. Guardia, James Rustvold, Robert A. Robinson, Christopher A. Robertson

In 1999, the Bonneville Power Administration (BPA) replaced approximately 730 m(2,400 ft) of damaged 42- and 36-inch concrete pipe by microtunneling Permalock pipe through sand and partly below groundwater. Microtunneling saved $3.5 to $5 million from the estimated cost of a shored excavation and avoided a railroad and contaminated valley fill. A slurry microtunnel boring machine (MTBM) was used for two segments where groundwater was present and a wheel excavator MTBM was used for one segment where groundwater was not present. This paper describes design and construction of this project that was completed within 2% of the bid and engineer’s estimate.

Jan 1, 2001

By C. L. Wilsey, K. M. Oakes, W. J. Reich, M. J. Protani

The time frame required to complete the National Environmental Policy Act (NEPA) process for a new mine, or for the expansion of an existing mine, can range between 9 months to 24 months, or more. The time frame will vary depending on whether an Environmental Assessment (EA) or an Environmental Impact Statement (EIS) will be completed. Completing properly designed baseline studies to collect natural resource data to support the EA or EIS prior to the start of the NEPA process can shorten this time frame. The two year natural resource baseline study completed by Homestake Mining Company for the Ruby Hill Mine, located in Eureka County, Nevada will be used as the case study to describe how properly designed and executed natural resource baseline studies streamlined the NEPA process.

Jan 1, 2001

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By P. Hickey, J. Spenceley, T. J. DeMull

Development of the Batu Hijau Project was successfully completed in the fourth quarter of 1999 with the final handover and start-up of ore processing facilities. The development project had started more than three years earlier, in August 1996, when the Owner, PT. Newmont Nusa Tenggara (PTNNT), awarded an EPC contract to Fluor Daniel (FD) for design and construction of the project including: copper concentrator, port, power plant, town site, and infrastructure. PTNNT managed the development of the mine and procurement of mine equipment with its own forces. Bringing the Batu Hijau copper deposit into production was the largest mining project ever undertaken. Development of Batu Hijau was a complex project involving the work of tens of thousands of people in all parts of the world to complete engineering, manufacture and deliver equipment, supply materials, and build the plant. The ore deposit is located on the tropical island of Sumbawa in a remote and undeveloped section of Indonesia. The location and environment presented challenges for all phases and aspects of the project. To meet the challenges, the project team combined good planning and teamwork to best utilize the resources available. This approach assured continuity of personnel through construction to operations and minimized cost, resulting in completion of the project ahead of schedule and under budget.

Jan 1, 2001