Search Documents

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.

By Joseph M. McCann

The Brightwater regional wastewater treatment facility, under construction in King County, WA, includes an extensive conveyance system that will feature deep, soft-ground tunnels and shafts. Excavation of the Ballinger Way Receiving Portal to 65.8 m (216 ft) below grade through challenging geology was accomplished by means of artificial ground freezing. This paper discusses freeze design development, system installation and monitoring, and the contractual and construction challenges that were overcome, including work sequencing and excavation means and methods, together with lessons learned.

By John F. Beesley

INTRODUCTION This paper discusses the design of the subsurface nuclear waste repository at Yucca Mountain, Nevada; and possible concepts for construction of the subsurface facility. Subsurface construction at Yucca Mountain is planned to last for 20 or more years, and may be accomplished using tunnel boring machines (TBM), drill and blast methods, raise bore machines, and roadheaders. The design of the subsurface facility includes approximately 107 km (66 miles) of tunnels and drifts. The vast majority of the repository will be excavated with TBMs. Design and construction concepts for the subsurface repository discussed in this paper are based on the License Application that was submitted to the U.S. Nuclear Regulatory Commission (NRC) by the U.S. Department of Energy (DOE) on June 3, 2008. The License Application was subsequently docketed by the NRC in September 2008. When a Construction Authorization is received from the NRC, notices to proceed with subsurface construction at Yucca Mountain will be issued by DOE. The Yucca Mountain site is located in the Mojave Desert approximately 150 km (90 miles) northwest of Las Vegas, Nevada. The site is on federal land in southern Nevada and is shown in Figure 1. Yucca Mountain is a ridge of volcanic rocks com-posed primarily of solidified volcanic ash. Previous underground construction work at Yucca Mountain included excavation of two tunnels using two different TBMs. The first tunnel, the Exploratory Studies Facility (ESF), is a 7.62 m (25 ft) diameter tunnel that is 7,877 m (25,843 ft) long and was described by Morris and Hansmire at the Rapid Excavation and Tunneling Conference (RETC) in 1995. The second tunnel, known as the Enhanced Characterization of the Repository Block (ECRB), was a TBM drive of 5.0 m (16 ft, 5 in.) in diameter and 2,681 m (8,796 ft) long. The second tunnel was excavated in 1998 and was described by Fulcher, Eastlund and Copeland at RETC 1999 and is named the East?West Cross Drift in that paper. (These previously excavated tunnels are shown in Figure 2.) In the volcanic rock formation where the vast majority of the planned repository will be con-structed, previous tunneling conditions were generally very good.

By Lorenzo Pellegrini

The respect of EPB reference pressure during TBM advance and hyperbaric activities, the complete and effective filling of the annular gap between tunnel lining extrados and the excavation section and a well organized monitoring system, to control surface settlements and ground distortion, are items of utmost importance in EPB tunnelling process. The paper describes how these concepts have been applied while excavating in the difficult underground conditions found at Sao Paulo (Brazil) during the execution of the Sao Paulo Metro Line 4-Lot 1. In this project, the annular gap has been filled by two components type, cement grouting. The back feed of the extensive monitoring campaign carried out to check the surface settlements during the excavation and hyperbaric maintenance operations will also be described in the paper.

By None None

Use this month wisely — go online and take advantage of your new member benefit. As an SME member, you can read and download for free all of the full-text papers of the Mining, Metallurgy & Exploration (MME) journal, including the 22 papers in the launch Special Issue on Mineral and Metallurgical Processing in Honor of Professor Emeritus Douglas W. Fuerstenau as well as the archived articles of Minerals & Metallurgical Processing (MMP), all the way back to Vol. 1, No. 1. Just follow the instructions on this page.

By Brian E. Gombos

During early stages of the detailed design for Detroit?s Upper Rouge CSO Tunnel Project, a Value Engineering Recommendation suggested the design team investigate alternative concepts to the usual cast-in-place or precast concrete lining system for the Project?s many smaller diameter Deaeration Vent Shafts. The resulting design investigation produced not only an alternative lining system, but lead to a proposed non-conventional approach to shaft installation means and methods through soil and rock necessary to construct the permanent shaft lining system. This paper will outline and summarize the technical issues, contractual restrictions, and cost considerations that eventually lead to the final shaft design

The National Mining Hall of Fame and Museum (NMHF&M) will induct its the 2014 National Mining Hall of Fame Class on Sept. 13, 2014 during its 27th Annual Induction Banquet and Ceremony at the Westin Hotel in Denver, CO. Representing the domestic and worldwide metal production, education, and health and safety sectors of the industry, this year?s four inductees cover a diverse cross-section of the mining industry. Harry M. Conger III, Günther Franz (Frank) Joklik, Ellen Swallow Richards and Dr. Alfred Weiss will join 223 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame. They were selected for being visionaries, leaders and ambassadors, both within their own sectors and across the industry at large. Conger was a great role model and strong advocate within Homestake Mining Co. and among his industry peers on behalf of environmentally responsible, safe, profitable and high-performance operations. As chairman and chief executive officer, Conger was instrumental in revitalizing and rebuilding Homestake into an industry leader in technological advances and environmental protection. Through his contributions in exploration, project development and operations management as Kennecott president and chief executive, Joklik did much to strengthen Kennecott as a company and assisted in restoring the competitiveness of the U.S. mining industry. Richards is generally recognized as the founder of ecology. She was the very definition of a pioneer in such diverse fields as chemistry, geology and mineralogy, mining and metallurgy, environmental science, public health, home economics and education. Weiss was a true visionary in using quantitative methods and digital computers to aid mineral exploration, plan and design mines, operate mineral production facilities and integrate the disparate information resources throughout a mining company into a modern management information system. NMHF&M Board of Directors Chairman, Paul C. Jones, said, ?Again this year we are honored to be able to induct an outstanding group of deserving individuals who have made exceptional contributions to the mining industry in the United States. Included are two living inductees who have made significant contributions to management in the industry. One inductee was the first female graduate from the Massachusetts Institute of Technology, its first female faculty member and the first female member of AIME who had an outstanding career as a mineral investigator in the United States. Another inductee was a lifetime innovator in bringing digital technology into common use in our industry. Each of our 2014 inductees made significant and lasting contributions to our industry and are well deserving of becoming a member of the National Mining Hall of Fame.? The Hall of Fame Induction Banquet and Ceremony is a marquee event for the National Mining Hall of Fame and Museum each year. The 27th Annual Induction Ceremony and Banquet will be held at the Westin Hotel in Denver, CO on Saturday, Sept. 13, 2014. For banquet reservations, contact the NMHF&M office at 719-486-1229. More information is available on the NMHF&M website at www.mininghalloffame.org.

By Crystal Poon, Paul Matlashewski, John Morkeh, Kathryn Dorfschmidt, Jose Carvalho, Chad Williams

Rockfall hazards are ubiquitous in mining environments making their control critical for safe mining operations. The complex processes involved in rockfall events necessitate a probabilistic modeling approach with well-calibrated material properties. The controls designed to mitigate rockfall hazards need to be reliable, efficient, and safe to deploy to meet the constraints present at an active mine. This paper presents an innovative solution to rockfall at Rio Tinto’s Bingham Canyon Mine. The solution incorporates the site-specific calibration and creation of a predictive rockfall model with the design, field testing, implementation, and monitoring of the rockfall controls.

What decision making tools and methods are available to a project owner when there is no clear differentiator between construction alternatives? A team led by a joint venture of Parsons Brinckerhoff and PGH Wong Engineering (PB/Wong) has been providing preliminary engineering services to the San Francisco Municipal Transportation Agency (SFMTA). The SFMTA and PB/Wong team developed several alternative construction methods for the tunnels and stations of the San Francisco Central Subway Project, none of which could be judged clearly better than another using traditional approaches and metrics. The team employed a risk assessment and analysis frame-works as a means of comparative analysis, drawing upon the knowledge of industry experts in the geotechnical, tunneling and construction fields to assist in the effort. This paper presents the approach and results of a cost and schedule risk analysis for two such analyses designed to answer two different questions regarding the advisability of different construction approaches. These assessments paved the way for key decision making in the preliminary engineering phase of the project and formed the foundation for continuing risk management efforts on the project. The focus of this paper is primarily the first two stages of risk management?identification and assessment?and some of the organizational dynamic issues that arise in such efforts.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By Tom Martin

Mega projects present unique challenges with regard to estimating costs. With such projects, which may span decades, these challenges often begin as soon as a project is conceived. The importance of having a sound, resource based estimate avail-able early in the process cannot be overstated because it provides the basis for ongoing project decisions. For the final phase of providing an updated cost estimate, often while bidding by contractors is underway, the Engineer?s Estimate (EE) must incorporate present market conditions; account for possible volatile material price swings; be based on actual labor and fringe costs; rely on meaningful productivity rates; and accommodate any recent technology advances while identifying and allowing for risk factors. This paper explains the benefits associated with consultants adopting a contractor?s estimating approach when preparing the Engineer?s Estimate on mega projects like the various tunneling projects in New York City.

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By C. J. Pritchard

The Office of Mine Safety and Health Research (OMSHR) investigated ways to increase mine airflow to underground metal/nonmetal (M/NM) mine working areas to improve miners? health and safety. One of those areas is controlled recirculation. Because the quantity of mine air often cannot be increased, reusing part of the ventilating air can be an effective alternative, if implemented properly, until the capacity of the present system is improved. The additional airflow can be used to provide effective dilution of contaminants and higher flow velocities in the underground mine environment. Most applications of controlled recirculation involve taking a portion of the return air and passing it back into the intake to increase the air volume delivered to the desired work areas. OMSHR investigated a Nevada gold mine where shaft rehabilitation was in progress and one of the two main fans was shut down to allow reduced air velocity for safe shaft work. Underground booster fan operating pressures were kept constant to maintain airflow to work areas, inducing controlled recirculation in one work zone. Investigation into system behavior and the effects of recirculation on the working area during times of reduced primary ventilation system airflow would provide additional information on implementation of controlled recirculation into the system and how these events affect M/NM ventilation systems. The National Institute for Occupational Safety and Health monitored the ventilation district when both main fans were operating and another scenario with one of the units turned off for maintenance. Airflow and contaminants were measured to determine the exposure effects of induced recirculation on miner health. Surveys showed that 19% controlled recirculation created no change in the overall district airflow distribution and a small reduction in district fresh air intake. Total dust levels increased only modestly and respirable dust levels were also low. Diesel particulate matter (DPM) levels showed a high increase in district intake mass flow, but minor increases in exposure levels related to the recirculation percentage. Utilization of DPM mass flow rates allows input into ventilation modeling programs to better understand and plan for ventilation changes and district recirculation effects on miners? health.

By Colin Barratt

The East Side Access (ESA) project is the largest underground rail infrastructure project under construction in New York City, USA. The Manhattan segment of the project is to be mined through rock and consists of 4.1 miles of Tunnel Boring Machine tunnels for track work and mined excavations to house rail switches, air plenums, and other rail facilities. This paper considers different methods for concrete lining, such as the use of fixed forms, adjustable forms, and pneumatically applied shotcrete. The advantages and disadvantages of these methods are discussed and the basis for considering one over the other are illustrated. Further discussions on design development and preparation of documents to facilitate quality and constructability in the field are presented.

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal mining operations can cause various disturbances to surface structures ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of the travelers and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (e.g., decks, beams, abutments, etc.) are presented. A number of mitigation measures to protect the bridge structures are recommended along with an actual application case.

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By Donald J. Olson

The North 27th St. ISS Extension tunnel will, under present plans, be the last constructed section of Milwaukee Metropolitan Sewerage District?s (MMSD?s) existing deep tunnel system. The 6.5 m (21 ft) finished diameter tunnel is approximately 3,260 m (10,590 ft) long and is located in NE Milwaukee County. When disputes over the pro-cesses to be used in owner-directed pre-excavation grouting in rock threatened the completion date stipulated between MMSD and the State of Wisconsin, the MMSD and J.F. Shea, the contractor, entered into a unique agreement. Shea accepted responsibility for all shaft and tunnel grouting and water control during the project in exchange for settlement of claims related to grout quantities and perceived delays. This significantly reduced risk for the MMSD and helped ensure the stipulated completion of the project.

By William Gleason

During the past five years, mining operations have had access to press technology for piping and joint fittings that can save owners a significant amount of time when installing or replacing pipes by eliminating the need for welding or threading. Viega, with North American headquarters in Wichita, KA, entered the mining sector in 2009, adding to its already expanding industrial sector. Since then, the company?s global engineering department has paid considerable attention to its industrial division, bringing its expertise in plumbing solutions for residential and commercial buildings to the mining and mineral extraction industry. ?We have a lot of applications in the mining industry.?We have a lot of applications in the mining industry throughout the United States, Canada and Mexico and continue to expand in the mining industry,? Tom Shields, Viega?s director for industrial accounts explained. ?Since we made the decision to increase our presence in the industrial markets, we have been aggressive and more than 240 applications have been approved by our engineering department in Germany.? Getting approval from Viega?s engineering department is no small feat. During a tour of the manufacturing facilities in Ennest and Großheringen, Germany, Mining Engineering, as well as a select few other publications and clients, were shown Viega?s manufacturing process. At the Ennest facility, hundreds of millions of fittings are produced, and each one is inspected mechanically and with a laser at the end of the production line. With four production facilities in Germany and one in the United States, Viega is able to ship to anywhere in the world. The company distributes everything from fittings to stainless steel pipe.

By Jacek B. Stypulkowski

This paper discusses the challenges faced by the design team of the under-river crossings of electric transmission feeders in New York City, a densely populated urban area. The under-river crossing of a 345 kV feeder was initially designed as Horizontal Directional Drilling (HDD), but was redesigned as a utility tunnel because of site con¬straints on both sides of the river. Multiple studies addressed location, available tech-nologies and costs. Multiple soil investigation phases addressed design aspects of HDD, as well as tunneling. Contractual issues varied from a design build alternative with Geotechnical Data Report (GDR) to design tender approach with GDR & Geotechnical Baseline Report (GBR).