Search Documents

By YOUNIS S. MUSTAFA, GHORASHI ZAIN, ABDEL-ZAHER M. ABOUZEID, AHMED A. S. SEIFELNASSR

The present paper attempts to characterize the breakage properties of a brittle rock, quartz, at different size fractions when compressed at various loads in a confined piston die.  This is to understand the interaction between the various parameters affecting the breakage behavior of a brittle solid in a confined zone. Application of the results may lead to improving the energy efficiency in the size-reduction units, which use compression as the main stressing force. 

By Hiroshi Yamazaki

The paper describes prediction, control and validation of face pressures, and special TBM features for the bored tunnels of the New Metro Rail City Project, Perth, Australia. The selected EPB-TBM passed below a heritage bridge and the operational Perth Railway station in ground conditions consisting of fully saturated uniform sand combined with shallow overburden and a horizontal alignment radius of only 135m. Therefore, strict control of volume loss, TBM operations and ground movements was vital requiring continuous evaluation and adjustments to TBM operation parameters. The paper discusses the effectiveness of applied TBM face pressures and the used foam/polymer soil conditioning which was measured against achieved volume loss and the predicted range of ground settlements.

By Stephen M. Smading

Unique onsite assembly of a 12.43 m Main Beam TBM and back-up system was completed on September 18, 2008 in the remote mountains of the Sichuan province of China. The equipment was assembled onsite, without previously having been assembled and tested in a factory, utilizing a method called Onsite First Time Assembly (OFTA). The Jinping-II hydroelectric project features four parallel headrace tunnels approximately 18 km long, two of which will be excavated by TBMs and two by drill and blast. A nearby fifth tunnel is being excavated by a 7.2 m TBM to draw down ground water in advance of excavating the headrace tunnels. This paper addresses the following topics: ¦Project description including geology and terrain; ¦The decision process leading to onsite first time assembly, the assembly process and logistics, and lessons learned; ¦Design features of the TBM and back-up system; and ¦Operational history from startup to the writing of the paper.

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits; thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium.

By Tony Peach

Project Description The Ok Tedi Mine is located approximately 18 km east of the Papua and New Guinea-Indonesia border, on the southernmost extremity of the Star Mountains Range, it is situated almost equidistant from the north and south coastlines. The headwaters of the Fly River system are in the Star Mountains. The open pit mining activities are on Mt Fubilan with a (pre-mining) elevation of 2,095 metres (6,871 Feet) in the Western Province. The mine is in an area characterised by very steep topography and dense tropical rainforest. The pit has been free draining but will cease to be so in the first quarter of 2009. Ok Tedi Mining Limited (OTML) required a drainage tunnel to be driven under the mine, if possible before free drainage was no longer possible. The tunnel was required to be at least 5 m in diameter and 4,200 m (13,776 ft) long, with a possible extension of 1,100 m (3,608 Feet) if the mine decided it was required for additional drainage and underground exploration. The tunnel is being driven up grade at 0.67%, and will be connected to the pit by the raising boring of two 1.1 m (3 Ft. 6 In.) diameter shafts from the tunnel level 250 m (820 Feet) below to the pit. In Tabubil, the adjacent township at an elevation of 640 m (2,100 feet), air temperatures range from a mean at night of 20 (68°F) degrees centigrade to a daytime aver-age of 27 (81°F) degrees. Extremes of 12 and 39 (54°F?102°F) degrees centigrade have been recorded. Rain falls, on average, 339 days each year and totals 8,000 mm (315 inches), and have been known to approach 12,000 mm (472 inches) making the area one of the wettest places on earth. The portal site is at an elevation of 1,200 m or 4,000 ft and the air temperatures are a little cooler and the rainfall a little greater. Access to the mine is by air for personnel and light freight and by ship for heavier goods and materials. The port is at Kiunga on the Fly River 153 km from the portal site. The program for the project was tight, the decision to purchase the required TBM was made in July 2007 and the final decision to go ahead with the construction of the tunnel was made in November 2007.

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By Michael Gilbert

In the world of tunneling the glamour is in the large diameter, long tunnels, but perhaps the number of projects for small diameter and short length tunnels are greater and generally have higher risk factors. Reasons for these higher risks include both the ?boiler plate? contract provisions used on these types of contracts, the technical specifications related to the tunnel work (versus the pipeline construction), the bid practices including measurement and payment and the construction. This paper reviews and comments on some of the key issues the authors have observed in recent major pipe-line projects that involve a small percentage of tunneling footage of the total contract.

By M. H. Morcali

Pistachio nut shells, an agricultural waste biomass, and Lewatit TP 214, a commercial sorbent, were investigated as adsorbents for the adsorption of platinum from dilute hexachloroplatinic acid solutions. Before the pistachio nut shells were carbonized, adsorption percentage was 65%, whereas Lewatit TP 214 ensured almost 100% adsorption. However, after the pistachio nut shell was carbonized at 1,000° C under an argon atmosphere, the platinum adsorption (%) increased two-fold. The effects of such parameters as sorbent dosage, contact time, temperature and solution pH on adsorption were studied in detail in batch mode. The adsorption equilibrium data were best fitted with the Langmuir isotherm model. The maximum adsorption capacities, Qmax, at 25° C were found to be 38.31 and 33.22 mg/g for the carbonized pistachio nut shell and Lewatit TP 214, respectively. The adsorption of platinum on both sorbents was found to be described by the pseudo-second-order kinetic model. The results indicated that the activated carbon prepared from pistachio nut shells can be effectively used for the removal of platinum from acidic solutions.

By Dean Brox

The use of Tunnel Boring Machines (TBMs) for tunnel construction of long tunnels in the Andes of South America has been of mixed success in the past due to a variety of reasons and key lessons can be recognized. A review of past TBM tunnel projects in the Andes has unveiled some interesting findings for different TBM tunnel approaches with both world records of progress as well as nearly in-completed projects with machines being abandoned. Key considerations for the use of TBMs for tunnel construction in the Andes include geological issues; (faults, rock type, rock strength, rock abrasivity, durability, groundwater inflows),depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, intermediate access possibilities, minimum tunnel size, support requirements, contractor and labour experience, and project schedule demands. TBMs offer highly recognized schedule benefits(high progress, no concrete lining) for a project if intermediate access adits are limited as well as hydraulic benefits for water conveyance projects. Minimum specifications for TBMs can be easily developed to suit the unique requirements of any project so as long as all factors are carefully considered. The overall conditions and factors associated with some projects may suggest that it is not appropriate to use TBMs due to a perceived high risk. Finally, access for geotechnical investigations by drilling in the commonly steep terrain of the Andes is typically difficult and often not impossible. Alternative approaches for geotechnical investigations for TBM tunnels including comprehensive mapping, high-resolution airborne electric-magnetics for delineation of possible fault zones, and rock block sampling is presented and discussed.

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By Hasan Nizamoğlu, Z. Abidin Sarı, Aslıhan Demiraslan, M. Deniz Turan, Tolga Depci

In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using HCl. The chemical composition of the solid was as 29.3%, 9.7%, and 13.3% for Cu, Fe, and S, respectively. Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp = 4.43 × 10−10) was performed by conventional leaching in the presence of HCl. The optimum leaching conditions were determined as 5 M of HCl concentration, 318 K of leaching temperature, 120 min of leaching time, 25 ml/g of liquid–solid ratio and 400 rpm of stirring speed. Under these conditions, approximately 77% of copper and 3% of iron were taken into the solution. According to the characterization of the leach residue that was obtained, the oxalate structure was degraded. Moreover, the results of XRD analysis showed that the sulfur (S) and cubanite (CuFe2S3) phases were mostly observed in leaching residues, and this was supported by the SEM-EDX data. Based on the results, it may be stated that selective copper extraction can be obtained from a chalcopyrite concentrate by a two-step leaching method using a conventional hydrometallurgical technique.

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2013 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration for the year 2013: 1) budgetary statistics expressed in U.S. nominal dollars provided by SNL Metals & Mining (SNL) of Halifax, NS, Canada (formerly Metals Economics Group (MEG); 2) regional and site-specific exploration activities that took place in 2013 as compiled by the USGS; and 3) regional events that affected exploration activities, including economic, social and political conditions, that were derived from published sources and unpublished discussions with USGS and industry specialists. Commodity and regional compilations are presented in this summary. Because multiple sources are used to develop commodity and regional compilations, reported statistics may vary depending on the source and type of data that are being reported. The SNL data summarize planned company budgets for worldwide exploration activities in 2013 for 20 nonfuel mineral commodities based on surveys returned by companies primarily focused on precious metals (gold, platinum-group metals and silver), base metals (cobalt, copper, lead, molybdenum, nickel, tin and zinc), bulk commodities (coal, iron ore, phosphate and potash), and specialty commodities (diamond, lithium, niobium, rare-earth elements, tantalum and uranium). Information on uranium exploration activities was included in the MEG overview for the first time in 2007. MEG included data on the commodities lithium, niobium, phosphate, potash, rare-earth elements and tantalum for the first time in 2010 because of the increased topical significance of these commodities. Since 1999, companies with exploration budgets of $100,000 and greater were included in the MEG and SNL compilations. SNL budget estimates exclude aluminum, coal, and oil and gas. Budget estimates for iron ore have been compiled since 2011 but reported separately. The post-1999 budget surveys by MEG and SNL cover at least 90 percent of world?s reported nonferrous, nonfuel mineral exploration budgets; the 2013 survey is reported by SNL to cover an estimated 95 percent of these budgets. The 5 percent that is not covered is accounted for by companies that chose not to participate in the SNL survey, private companies that do not publish their budget data, and government-funded exploration activities.

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By I. M. Ahmed, R. S. Hassan, M. I. Aly

Extraction and separation of La, Sm and Dy ions from acidic sulfate-phosphate solutions was investigated using a cation exchange extractant, bis(2,4,4-trimethylpentyl) phosphinic acid, CYANEX 272, in kerosene. The influence of shaking time, equilibrium pH, extractant, sulfate and phosphate ion concentrations, diluent type and temperature was studied. The extraction was found to be pH-dependent, and increasing the phosphate ion concentration inhibited the extraction which was found to be endothermic. The stoichiometry of the extracted metal species was found to be MOH.H2OHSO4H2A.A2. Aliphatic diluents were found to enhance the extraction compared to aromatic diluents. The results showed that there was a separation mode between the metal ions when varying the hydrogen ion and sulfate ion concentrations, under the used experimental conditions. The investigated process was used for the recovery of La, Sm and Dy from the acid solution resulting from the leaching of low-grade monazite.

By G. A. Christie

This paper presents a vision system capable of providing an accurate estimate for the volume of stockpiles using 2D images. By imaging a stockpile from multiple viewpoints with a two-camera system, a 3D point cloud of known scale is generated using image-based 3D reconstructions. With a small amount of user interaction, the points that correspond to the surface of the stockpile are extracted and used to measure the volume. The hardware required for the two-camera system is light enough to be carried by a small unmanned aircraft and is a cheaper alternative to LiDAR while still being competitive in terms of accuracy. When testing the volume measurement algorithm on a stockpile of known volume, the measured output was found to have less than a 3% error from the ground truth.

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By C. K. C. K. Gupta

The rare earths in elemental form are required for a variety of scientific and technological purposes. They are not easily obtained in this form, due to the great chemical stability of the rare-earth compounds and the strong tendency of elemental metals to react with everything they come in to contact with, especially at high temperatures. Beginning in the 1950s, when sufficient quantities of separated rare earths became available, as the result of intense research and development, three processing routes were developed to accomplish the preparation of all 16 naturally occurring rare-earth elements. They are chemical reduction of the halide intermediates, the oxides and electrochemical reduction of chlorides and oxide-fluoride mixtures. Not all the processes are effective with all the rare earths. In spite of the celebrated similarity of trivalent rare earths, the physical properties of individual rare-earth elements are sufficiently different that a variety of techniques are required for their preparation. The development of reduction processes for the rare-earth metals are covered in this paper, with focus on the oxide reduction routes. The strong reliance of effective reduction processes on the fundamental science of reduction reactions is highlighted.