Search Documents

By R. C. Dunne, C. T. O'Connor

Flotation practice on eighteen South African flotation plants is described. The plants are categorized as those treating reclaimed tailings, those treating material which has already been subjected to cyanidation or uranium leaching, and those treating milled ore. The similarities and differences are highlighted.

Jan 1, 1998

By Stephen Young

The continuous monitoring of free cyanide levels is an important part of gold recovery operations. Accurate and up to the moment knowledge of the free cyanide concentration can result in substantial cost savings by allowing reduced concentra­tions with lower fluctuations, while maintaining or increasing gold recovery. Reduced free cyanide levels also result in lower detoxification costs at the mill discharge which translates into further savings while meeting environmental requirements. As can be seen from the upper curve in Figure 1 (which is based on in-service measurements), without accurate monitoring and control, cyanide concentration fluctuates during the produc­tion cycle, and is maintained at a high level to err on the side of caution. The lower curve illustrates the improved control permitted by the installation of a CY ANCOR, giving a more consistent concentration over the process cycle, and safely allowing use of a lower concentration.

Jan 1, 1995

By Gordon V. lewis

The Penjom gold mine treats highly preg-robbing carbonaceous ore by using relatively inexpensive gravity and hydrometallurgical methods. The mine is a joint venture between Avocet Gold Limited, a subsidiary of Avocet Mining PLC, a U.K listed mining company with interests in gold and tungsten, and the Pahang State Development Corporation (PKNP) who receive a 2% royalty. The operating team at Penjom embarked on a programme of innovation during 1998 following a realisation that almost all of the primary ore in the gold deposit was highly carbonaceous in nature. Earlier attempts at desliming and leaching the deslimed product through a normal CIL circuit had failed, and through shear necessity, the team turned to new technologies which were considered most suited to the ore characteristics indicated from pre­feasibility testwork. Between April and September, 1998, the mine introduced three key processes, which combined represent the elements of "The Penjom Process". The gravity circuit was boosted to maximise the capture of leachable sulphide and free gold from the relatively carbon free cyclone underflow stream, kerosene and diesel blanking was introduced to treat the cyclone overflow and RIL (resin-in­leach) technology utilised to replace the existing CIL (carbon-in-leach) circuit. Further experimentation with selective resin in partnership with Mintek of South Africa yielded a significant improvement to the process during 1999. Minix­Dowex resin was introduced mid year to replace a non-gold selective resin, which had been used in a flotation/batch leaching circuit for about nine months. Lower carbon levels in the feed at that stage led to the abandonment of flotation and the introduction of continuous RIL, which has been adopted as the major chemical process at the Penjom gold mine since September, 1999. Given the proven performance of the circuit to date, this process may be considered as a low cost option for the treatment of highly carbonaceous ores, particularly those which are not refractory and contain a reasonable percentage of free gold.

Jan 1, 2000

By Scott W. Beckman, Leslie C. Thompson, Joseph A. Kizis

Heap leaching of ore with cyanide is a common and economical means of extracting precious metals (gold and silver) from mined ore. The use of cyanide, and the heap leach process, can seriously impact the environment. In the worst case, catastrophic failure of containment structures can release toxic levels of cyanide into receiving bodies of water, resulting in toxicity to ecological communities and contamination of public water supplies. Furthermore, cyanide degradation products such as nitrates can also impact local streams, lakes, and aquifers. Even if cyanide can be removed, the crushed residual ore may generate acid solutions that can release toxic heavy metals into the environment. Pintail Systems, Inc. (Pintail) of Aurora, CO, in conjunction with technology partners Science Applications International Corporation (SAIC) and Fairmile Gold Corporation (Fairmile), have developed a microbially-based precious metal lixiviant that can be used as an alternative to cyanide. The microbial process, called BioLix, is Pintail's second-generation biotechnology product for the recovery of precious metals from ore. The BioLix process is based on the enzymatic induction of organic lixiviant compounds using proprietary inducing agents and microorganisms. The process operates at near neutral pH and ambient temperatures using non-pathogenic microorganisms and food-grade chemicals. Precious metal extraction is also enhanced through the employment of microorganisms that facilitate mineral-solution reactions such as surfactant generation (improved wettability), and oxidation of gangue minerals that expose mineral surfaces to leaching. In order to demonstrate the effectiveness of the BioLix process, results from laboratory bench-scale experiments and a column study are presented. In addition, new applications for this enabling technology are discussed and include re-leaching of spent ore heaps, in situ leaching, and cyanide replacement for heap leaching.

Jan 1, 2000

By S. R. LaBrooy, J. Avraamides

Thermal reactivation of eluted carbon is an essential part of most carbon-in-pulp gold recovery plants. The effectiveness of the reactivation procedure depends on the nature and level of contaminants adsorbed on the carbon, the efficiency of the elution and the temperature, residence time and atmosphere within the kiln. The most commonly used kilns are evaluated in terms of their operating parameters and performance. Data obtained both in the laboratory and in the field emphasize the importance of carbon feed moisture content, kiln atmosphere and carbon conditioning on the activity of the kiln product.

Jan 1, 1998

By Julia R. Budden

The role of bacterial oxidation in the mining industry is becoming more widely accepted. Western Australia has accepted the technology as a pretreatment for refractory gold concentrates more readily than most. The third of such plants has been completed at the Y ouanmi Gold Mine. This is situated approxi­mately 500 kilometres north east of Perth, in the Yilgarn mineral field. Y ouanmi concentrates are produced from underground ore and contain arsenopyrite and pyrite as the main sulphide miner­als. Refractory gold from this deposit is generally associated with the arsenopyrite portion of the material. Gold Mines of Australia Ltd ("GMA") initiated pilot scale testing at the BacTech premises in November 1993. The decision by GMA to use BacTech's technology was announced in February 1994. Design and construction commenced at this time. Bacterial growth on site was initiated in July 1994 and continuous opera­tion began in the October. Concentrate was added at 0.5 tonnes per hour and this has increased to 1 tonne per hour.

Jan 1, 1995

By James L. Hendrix, Michael R. Straka, Emil B. Milosavljevic, Ljiljana Solujic, Neil P. Gallagher

Analysts that utilize the classical distillation procedures for cyanide analysis are often frustrated by the poor reproducibility and repeatability of these techniques. Capital intensive business decisions and environmental management regulations are exas­perated by the fact that the EPA/ASTM approved cyanide deter­mination methods produce data of questionable quality. Reliable cyanide values are important in monitoring the effec­tiveness of the cyanide detoxification procedures. Efficiency and cost of gold and silver cyanidation recovery can also be improved by precise cyanide monitoring in the process itself.

Jan 1, 1996

By Mike Jahraus

The topic I would like to throw out for discussion this morning concerns the metallurgical solution management of operating a valley fill leach facility where ore depths approach 250 feet and deeper. We are currently beginning to experience solution transport times through our heaps on the order of 60 to 70 days as our heaps approach 250 feet. Incorporating a two-stage leach scenario, or solution enrichment, these times are nearly doubled. Concurrent with the increased solution transport times, the solution tenors being produced by our heaps are being diluted slightly as percolation occurs through the lower lifts. I feel the best way to handle these situations is to closely monitor solution application rates, and carefully manage ore stacking. Also, as heaps become deeper, metallurgical and hydrologic characteristics of the ore become inter-related, i.e. if channeling or preferential flow is taking place, lowering cross-sectional flow rates to older leach panels with help re­institute capillary flow while helping to prevent solution tenor dilution.

Jan 1, 1999

By Mike Rhodes, Paul Miller, John W. Neale, Vishal Deeplaul, Barrie Hancock, Tony Pinches

The Beaconsfield underground gold mine is one of only a few new Australian gold projects to come into operation in the current climate of low gold prices. Up to 200,000 tonnes per annum of Tasmania Reef ore will be mined and processed over a minimum eight-year life to a depth of 900 metres below surface. The Tasmania Reef is a gold-bearing quartz-carbonate-sulphide vein occupying an old fault structure which transgresses a series of sedimentary beds. The sulphides are predominantly pyrite with lesser arsenopyrite, and also minor copper as chalcopyrite. Drilling to date below this level clearly indicates that the high-grade orebody is open at depth and that the mine life should be extended significantly over time. Since redevelopment of Beaconsfield mine began in the 1980's, extensive exploration has identified a resource of 1.5 million tonnes within a 450 vertical metre zone beneath the old workings, which extended more than 450 metres below the surface. Installation of an 800 litre per second capacity pump station 180 metres below the surface has been critical in overcoming one of the major hurdles experienced during previous operations in the early 1900's. A multi-stage development program, designed to bring the mine into full production, and incorporating construction of the on-site gold treatment plant incorporating bacterial oxidation, has now been completed. Prior to execution of a detailed engineering design of the Mintek-BacTech bacterial oxidation process, a programme of bacterial oxidation testwork was completed to provide a basis for fixing the process design criteria. A flow diagram of the Beaconsfield treatment plant is shown in Figure l. It comprises:

Jan 1, 2000

By J. G. Dunn, A. S. Ibrado, D. J. Hollbach

Gold production is one the most important mineral process­ing industries in Western Australia. The gold is usually found in either weathered oxidised zones, or associated with sulfides. In the latter case, oxidation is achieved by some form of chemical processing, such as roasting or more recently bacterial leaching. In all cases, gold is dissolved out of the oxidised matrix by cyanide solution. Pyrrhotite is an iron sulfide generally represented by the formula Fe1_,S where O x 0.125. Three different structural forms ofpyrrhotite are known to occur naturally, stoichiometric FeS (troilite), hexagonal pyrrhotite Fe1_xS and monoclinic pyrrhotite Fe7S8 [I]. Substitution of iron atoms within the pyrrhotite structure by other ions of similar atomic radius such as nickel, copper, cobalt and manganese is also possible [2], and often observed in natural pyrrhotite samples. Pyrrhotite is abundant in Western Australian sulfide mineral deposits which are commonly associated with gold bearing ores. It is generally believed that pyrrhotite has a detrimental effect on gold recovery from such ores, as it is commonly claimed to decompose in alkaline, aerated cyanide solutions to form iron cyanide complexes, thus consuming free cyanide, and to form sulfur/oxygen containing species such as sulfate, through oxidation of sulfur in pyrrhotite, which thus consumes oxygen. From information gleaned from the literature, claims about the high reactivity of pyrrhotite in cyanide appear to be based on early cyanidation studies performed on gold ore samples which have been poorly characterised, and contained impurities such as pyrite, arsenopyrite and chalcopyrite, which may have also contributed to the levels of species observed in solution [3-5]. In addition, the investigations do not take into account that iron atoms in the pyrrhotite structure may have been partially substituted by other atoms that influence the solubility of pyrrhotite in cyanide solution.

Jan 1, 1995

By M. J. Virnig, J. M. W. Mackenzie, M. W. Johns

The properties of Henkel's Aurix® resin which uses a guanidine functionality to recover gold by ion exchange have been described in publications of the International Mineral Processing Congress and Randol International (1)(2). The purpose of this paper is to provide an update on the results of further testwork using Aurix®. Specifically, this paper presents the first results of resin in pulp testing, all the results previously reported were for testwork carried out using synthetic gold leach solutions.

Jan 1, 1995

By Paul Hamilton, Brian Jones

Traditionally,relatively large gold mines in developing countries have relied on imported process plant engineering, design, pro­ject management and advisory skills. In 1995, there was a significant departure from this in Zimbabwe, when a locally based engineering company under­took and completed the construction of a one hundred and twen­ty thousand tonne per month capacity gold extraction plant for the treatment of sands/slimes residues integrated with run of mine ore. This paper describes the challenges of designing, construct­ing and commissioning a Carbon in Leach (CIL) gold extraction plant in a developing country, and discusses the various con­straints associated with it. In addition, the paper reviews the application of technology which is innovative to Zimbabwe, including the use of dewatering cyclone clusters, and two and a half tonne capacity elution/electrowinning convection units.

Jan 1, 1996

By Joe Hudson

The successful heap leaching of tailings as illustrated in the two photographs below, requires special provision. These will be enumerated in the presentation. The two illustrations show the project as it evolved. Note the bermed pads and the conveyor materials handling system which provides for agglomeration of the feed material.

Jan 1, 1998

By William G. Pariseau, Mark K. Larson, Heather E. Lawson

Rational design based on engineering fundamentals is essential for the layout of safe, stable shafts and tunnels. Shafts and tunnels including winzes, raises, adits, and crosscuts are lifelines to the underground and must be secure. The contribution of this paper describes a significant extension in existing software previously developed for five important design problems in strata-bound mines such as coal, trona, salt, potash, and some large, lead-zinc mines. This extension in software allows analysis to proceed in three easy steps: (1) preparation of a strata properties file, (2) generation of the finite element model, a mesh, and (3) finite element program execution. Circular, elliptical, and rectangular shaft sections are available for a single shaft, twin shafts, and shafts in a row. Spacing of twin shafts and shafts in a row is a free parameter (pillar width). Tunnel shapes are the same as shafts but include the conventional arched back section. Dipping strata of variable thickness, depth and orientation relative to the excavation of choice are allowed. The analyses are three-dimensional. An elastic-plastic material model based on associated rules of flow and an N-type yield condition for isotropic, transversely isotropic, or orthotropic rock are used for all strata. Example analyses from several hardrock mines are provided to illustrate the three-step process including mesh plotting and plotting of selected results. The goal of this software is to advance mine design technology for improved miner health and safety.

By R. G. Hite, R. G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, devel reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mechanics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1992

By Harry M. Castrantas

Caro's acid (peroxymonosulfuric acid-H2SO5) is used to destroy cyanides in tailings slurries due to its rapid reaction and low capital and operating costs. Due to its instability, Caro's acid is generated at the mine site using a hot or cold process. The majority of gold mines that use Caro's acid use the FMC hot process. In the FMC hot process, it is not necessary to cool the Caro's acid to minimize decomposition since it is used immediately upon generation. In contrast, the cold process uses a chiller to cool the raw materials and product. This paper will show, using laboratory and field data, that there is virtually no difference in Caro's acid yield between the cold and the FMC hot processes. Caro's acid yield depends on the mole ratio and concentration of sulfuric acid and hydrogen peroxide and is independent of operating temperature.

Jan 1, 1997

By Richard H. Johnson

The Castle Mountain Mine (CMM) is located in the eastern por­tion of San Bernardino County, Southern California, 70 miles south of Las Vegas. The CMM is a joint venture between Viceroy Gold Corp. (75% and operator) and MK Gold (25%). The CMM initially started gold production with an 8,000 tpd cyanide heap leach operation in February, 1992 when the first ore was crushed and delivered to the leach pads. Even during construction and commissioning, design work was under way to engineer and construct a 1,200 tpd Mill circuit to process the higher grade fraction of the ore through use of pulp agglomera­tion. The need for a grinding circuit became evident with the quantity of high grade material delineated during drilling and the amount of visible gold that the geologists were finding in the drill core and R.C. cuttings. Viceroy did not want to stack the higher grade ore on the heap, and it was clear that permitting a tailings pond would, at best, be a long drawn-out affair. An alternative to a tailings facility had to be found.

Jan 1, 1996

By Robert Dunne, John Angove

The physical properties of an ore body require determination for virtually all mining projects, new and existing. The extent and regularity of such determinations being subject to the size and homogeneity of the orebody. Such properties have an impact at the design stage of new plants, with respect to equipment specification, and thus effects capital costs; and also impacts on the operating costs of new and existing plants, with respect to power consumption, production levels and part replacements. All of these can severely alter the bottom line and can be the determining factor in the economic viability of many projects. This paper examines some of the most common properties that are measured, the procedures utilised in determining these properties, and their variability under conditions of reproducibil­ity, and to a lesser extent repeatability. The properties looked at were Impact Crushing Work Index, Abrasion Index, Bond Rod Mill Work Index and Bond Ball Mill Work Index. A number of testing laboratories throughout Australia and the US were utilised in the survey. The results showed up some interesting and important features of the procedures used, all of which have become accepted industry standards, and which had varying effects on the final result. Tests such as the rod and ball mill indices would appear to have reasonably robust procedures which allowed for the determinations of the respective index without the introduction of significant variations, although there were indications that variations could occur. The other tests gave a sufficiently different picture to be able to suggest that an argument could be made for a more intensive investigation to be undertaken, with the possible outcome that a modified test procedure or an alternative test is required.

Jan 1, 1997

By Gary L. Simmons

Many large (refractory) sulfide gold resources exist in Nevada and other parts of the world that are not amenable to conventional flotation concentration using air as the flotation gas medium. Over the past five years Santa Fe Pacific Gold Corporation (SFPG) has investigated flotation process options to economically treat refractory ores and resources of this type at its Lone Tree and Twin Creeks mines. Conventional flotation technology applied to the original high-grade gold resources at Lone Tree and Twin Creeks was initially unsuccessful. Review and analysis of auriferous (gold-bearing) iron sulfide mineralogical characteristics and flotation ..:hemistry provided a fundamental understanding that led to the development of a new flotation process that SFPG refers to as N2 TEC. This paper discusses the development of this technology and compares N TEC results with conventional flotation practice.

Jan 1, 1997

By Richard M. Crowell, John W. Shield, Todd J. Harvey

Facing lower gold prices, gold mine operators throughout the world are seeking ways to reduce costs for treating refractory sulfide ores. Many gold mines, currently producing oxide ores, have underlying refractory sulfide deposits and the operators could extend the mine life by processing these sulfides. Fortunately, oxidation technologies for refractory ores need not be complex nor costly. GeoBiotics, Inc. has developed heap biooxidation technologies (GEOCOAT™) for treatment of refractory gold ores and concentrates. GEOCOATTM uses simple low cost unit operations common to heap leaching of gold and copper ores. The cost effectiveness and flexibility of GEOCOAT™ heap biooxidation allows mining companies to expand operations to include refract01y ore. In addition, GEOCOAT™ can be utilized to supplement or replace existing oxidation processes such as roasting, autoclaving, or agitated tank biooxidation, and to treat a lower resource grade than is currently economic. The GEOCOAT™ technology involves coating sulfide concentrates onto sized support rocks and biooxidizing the sulfides in a heap configuration. After biooxidation the concentrate is stripped from the support rock, neutralized and leached in conventional cyanidation facilities. Ashanti Goldfields Company Ltd. (AGC) produces over 885,000 ounces of gold per year from oxide and refractory ores at its Obuasi operations in Ghana. Refractory flotation concentrates are treated in roasters and in the world's largest stirred tank biooxidation facility. In August 1998, AGC and GeoBiotics jointly constructed and operated a field demonstration heap of the GEOCOATTM process at the Obuasi operations. The heap contained I 082 tonnes of support rock and 125 tonnes of concentrate. The heap was approximately 19 meters square at the base and 3.8 meters high, and ran for 88 days after which the concentrate was reclaimed. Average gold recovery after biooxidation was 91.5% with a NaCN consumption of 8.6 kg/t. Baseline gold recovery by direct cyanidation of the concentrate was 53.8%.

Jan 1, 1999