Search Documents

By Colin J. Booth

Hydrogeological impacts of active longwall mining were studied at two sites in Illinois. At the site with the more transmissive sandstone aquifer, aquifer permeabilities increased an order of magnitude due to subsidence. Piezometric levels declined with subsidence due to increased porosity, and ahead of mining due to a transmitted drawdown. Levels recovered rapidly at first and fully over two years. At the site with the less transmissive aquifer, impacts were similar except that recovery has been limited. Local aquifer enhancement through increased yield can occur, but only where the aquifer is transmissive enough for recovery.

Jan 1, 1986

By J. P. Fitzgerald

This paper is an accumulation of information on the geology, mineralogy and mining of the Hectorite clay deposit owned by NL Chemicals (U.S.A.), Inc. The mine is located in San Bernardino County, California approximately 35 miles east of Barstow and 1-1/2 miles south of U.S. Highway 40. The region is known as the Mojave Block which is a region bound by the San Andreas fault zone to the southeast and the Garlock fault zone to the North. The faults of both zones are active, vertical faults along which movements are mainly horizontal. Most of the faults within the Mojave Block are high angle faults which trend northwest. They are considered part of the San Andreas fault system and are a result of the right- lateral movement characteristic of this system. The east-trending faults are also high angle faults, along which movement has displaced rock units vertically. Manix fault is the only mapped fault that shows evidence of left slip which is characteristic of the Garlock sys tem to the North.

Jan 1, 1986

By Robert A. Cummings, Madan M. Singh

In April 1984 a subsidence depression formed directly beneath a two-story frame residence, near Linton, IN, causing 2 ft of separation between the floor and walls, and damaging both the foundation and interior of the building. The Office of Surface Mining undertook the rehabilitation of the area under its emergency response program. This paper describes the investigation performed to determine the cause, severity, and extent of the problem. Abandoned mine workings were found approximately 55 to 60 ft below the house. Based on the findings, remedial measures were prescribed. An abatement program consisting of grouting the mine voids was recommended, and specifications prepared. These were implemented, and the area has been successfully stabilized.

Jan 1, 1986

By Robert W. Bruhn

Ground movements associated with high extraction underground coal mining, such as pillar retreat and longwall, are some- times large enough to disrupt the ground water regime as well as damage buildings and other surface structures. A U.S. Department of Energy Bureau of Mines- sponsored subsidence study at Kitt Energy Corporation's Kitt No. 1 Mine near Philippi (Barbour County) , West Virginia has provided an opportunity to monitor the ground water response above a mine panel during both developmental and pillar re- treat mining. Findings concerning ground water effects presented in this paper indicate that total extraction mining produced significant water level declines in deep-lying strata but had little effect on water levels at shallower depths. Post-mining values of hydraulic conductivity were typically somewhat higher than pre-mining values. Changes in water chemistry associated with mining were not sufficient to render the water unfit for human consumption.

Jan 1, 1986

By Wolfgang R. Wawersik, Charles M. Stone

INTRODUCTION Hydraulic fracturing was applied in horizontal drill- holes in the Salado salt formation near Carlsbad, New Mexico. Tests were performed approximately 650 m be- low surface to validate the design of a Waste Isolation Pilot Plant (WIPP) for the disposal of radioactive waste from defense activities of the United States. Hydraulic fracturing was performed primarily to determine whether the virgin in situ stress state at the WIPP site is isotropic and whether the magnitude of the virgin in situ stresses corresponds to the weight of the overburden. Beyond these limited objectives, however, measurements are now being reviewed to evaluate the usefulness of hydraulic fracturing in salt formations in general. Such measurements are desirable to determine stresses induced by mining and to monitor time-dependent stress changes around underground excavations in salt masses. Hydraulic fracturing was chosen because it is the only technique that can be readily applied in virgin ground far from existing mine openings. The method also appeared to yield directly the magnitude of the least compressive principal stress, regardless of the mechanical properties of the rock mass. A knowledge of the least principal compression was deemed sufficient to establish the isotropic character of the virgin in situ stress field under two conditions: (1) the Salado formation was mechanically isotropic, i.e., the fracture toughness did not vary normal and parallel to bedding so as to permit preferred fracture paths, and (2) pressure measurements were combined with determinations of the orientations of hydraulic fractures and, more generally, with observations of the characteristic hydraulic fracture patterns. The latter was possible by locating the drillholes for hydraulic fracturing along the axes of drifts that were mined several months later. The success of general stress measurements by hy- draulic fracturing of salt subjected to anisotropic stress conditions was and remains less certain. While the smallest in situ compressive stresses should still be equal to instantaneous shut-in pressures, there may not exist any unique relationships between the greatest and intermediate in situ principal stresses on one hand and the primary breakdown and fracture reopening pressures on the other. This problem would be a consequence of stress relaxation due to salt creep around any drillhole in which hydraulic fracturing tests are conducted. Moreover, lab- oratory measurements suggest that creep and stress relaxation could be so rapid that it might not be possible to interpret the measurements for anisotropic stress conditions even if hydraulic fracturing were performed as soon after drilling as possible. The primary objectives of the stress measurements in the WIPP were met by combining hydraulic fracturing tests with finite element analyses of the effects of salt creep, observations of hydraulically induced fracture pat- terns, and laboratory hydraulic fracturing tests on oriented core. In situ hydraulic fracturing tests in long drillholes were preceded by several trial tests to establish the best test methods and to demonstrate that salt could be fractured. The resolution of anisotropic stresses and special problems, e.g., in the identification of instantaneous shut-in pressures, are currently being addressed in hydraulic fracturing tests in a mine pillar, in tests following different delays between drilling and fracturing, and in tests with different frac fluids. This paper will review the main results of the analyses above and of one group of hydraulic fracturing tests at different distances from existing excavations. The paper will conclude with a brief description of the geometry of the hydraulically induced fracture patterns. Because of space limitations, it will be assumed that the reader is familiar with hydraulic fracturing or will first consult other sources (e.g., Cleary, 1980; Gronseth and Detournay, 1979; Zoback and Haimson, 1983; Nemat-Nasser et al., 1983; Kim et al., 1984)

Jan 1, 1986

By G. V. Borquez

For many years drilling and blasting has been considered more of an art than a science. This is still true in some respects, but today scientific approaches to drilling and blasting design must be used to plan an efficient operation which achieves desired fragmentation within constraints. These constraints involve minimizing damage to the wall or nearby permanent structures and avoiding undesirable fragmentation and mine dilution which can adversely affect operation costs. The degree of fragmentation by blasting is the most important single factor in any attempt to optimize the overall cost of the mining operations. The mining cycle begins with the drilling and blasting operations, which result in a given blasted rock size distribution. While this operation represents only about 20% of total mining costs, the efficiency and costs of the subsequent operations are strongly dependent on the fragment distribution obtained.

Jan 1, 1986

By W. M. Ma, W. L. Zhong, Syd S. Peng

In a longwall section that consisted of 7 longwall panels, there were two high pressure gas transmission pipelines across the panels burying from 3 to 10 ft. below the surface. One pipeline was 20 in. in diameter while the other was 24 in. in diameter. In order to investigate the stress conditions sustained by the pipelines during underground longwall mining, strain gages were mounted on the pipelines above panel #3, #4, and #5. Survey monuments were also installed along but near the pipelines. This paper presents a subsidence prediction method and the preliminary results of the pipelines' stress conditions as affected by underground longwall mining.

Jan 1, 1986

By Giin-Fa Fuh, Sally A. Shoop

An instrumentation program was developed based on the results of an analytical study of the geomechanical effects of longer longwall face lengths. Boundary element simulations showed that longer face lengths can cause in- creased face convergence and an increase in the shear stresses in the immediate roof. Empirical design methods predict that longer faces will cause little effect on abutment stresses as long as the roof caving is well behaved. On this basis, a longwall face instrumentation program was designed with emphasis on the interaction between face support and ground response for optimizing face conditions. At a 600-foot (183 m) face, five midface shields and two headgate shields were monitored with vary- ing hydraulic pump pressure. The instrumentation included six convergence rods with linear potentiometers to measure canopy-to-toe convergence; fourteen pressure transducers to monitor leg pressures; and two portable data loggers. Similar instrumentation will be in- stalled on a 750-foot (229 m) face for comparison. The results from the 600-foot (183 m) face indicate that a ground reaction curve, as determined from the relationship between the sup- port set pressure and the roof convergence, can be used to optimize the support pressure to control convergence, the key element to ground stability in the face area.

Jan 1, 1986

By Terry L. Logan, Arfon H. Jones, James C. Seccombe

Deeply buried coal seams [greater than 3000 ft (914 m)] are difficult and sometimes hazardous to test and complete due to coal sloughing, formation pressure anomalies and coal fine generation. Data collected while stimulating two deep coalbed methane wells located at the Gas Research Institute/Resource Enter¬prises, Inc. "Deep Coal Sean Project" test site in the Piceance Basin, Colorado, is presented in this paper. A single thick coal seam was completed openhole in each well. Core data, reservoir data, in-situ stress measurements, and pre-stimulation calibration test data were collected at the site to use in the design of the fracture stimulation treatments for both wells. A nitrogen foam fracture fluid treatment was selected for the first well and a linear gelled water for the second well. Treatment pressures were monitored with a downhole quartz pressure transducer. Atypically high treating pressures were observed, possibly indicating coal fines plugging at the fracture tip or increase in fluid viscosity caused by interaction of the generated coal fines with the fracturefl uid. In addition, a comprehensive fracture diagnostic effort was employed during the fracturing of the second well; namely, triaxial borehole seismic, seismic televiewer, hydraulic impedance monitoring, gamma ray log (in conjunction with radioactive additives in the sand), and temperature log. The results indicate a vertical fracture was created parallel to the face cleat as expected.

Jan 1, 1986

By Vladimir Admek, Paul W. Jeran, Michael A. Trevits

It has' been found that lithological conditions over the Pittsburgh Coal bed cause the subsidence coefficient to vary within the area of the subsidence trough. This precludes the use of European developed predictive models, which are based upon a constant subsidence coefficient. Regression analysis of the distribution of subsidence coefficients from 11 Bureau of Mines, U.S. Department of the Interior, longwall panel studies on the location relative to the edge of the panel has yielded a third degree polynomial equation. This equation has been incorporated into a BASIC computer program for use on a personal computer that allows users with no previous knowledge of the theory of subsidence to predict vertical movements over typical longwall panels in the Northern Appa1achian Coal Basin.

Jan 1, 1986

By K. S. Radcliffe

Results are presented for the first phase of an experimental program to study the feasibility of using acoustic velocity for predicting the state of stress in a rock mass. Compressional wave velocities were determined axially in cylindrical samples during uniaxial compression for several rock types conditioned in dry and water-saturated environments. Results indicate that in rocks containing compressible voids or cracks, substantial velocity change occurs with the application of stress in the lower (below 100 MPa) stress regime. The effect norm- ally is nonlinear, however, and diminishes to asymptotic values when cracks or voids become closed or with saturation. Empirical prediction equations were derived for each rock type by linear and nonlinear regression analyses, and correlation coefficients were calculated to determine the equations that best fit the stress- velocity data. The operational range for predicting stress using compressional-wave velocity appears to be within the range of vertical stress expected in most shallow to intermediate depth mining operations (less than 1,000 m). Based on the experimental results to date and theoretical considerations, it appears that the technology can be advanced to predict in situ stress based on acoustic P-wave velocity determinations in most mining situations.

Jan 1, 1986

By John D. Gardner

This paper describes a process which finds the maximum worth of a mineral deposit. The procedure requires two phases. The first uses a microcomputer evaluation model to find the optimum design input, with minimum attention giving to actual mining constraints that might exist. The second phase runs the first-phase design parameters through a direct simulation model on a mainframe computer. In phase one, financial, economic, and geotechnical data are entered; and an idealized list of design parameters is output. The list includes optimum values for cutoff grade, mine life, mine size, paytons, paygrade, and payvalue. In addition, the model generates pro forma operating and cash flow statements and it indicates the maximum net present value (NPV) possible for the deposit along with the probability of that oc¬curring. The initial results imply perfect mining conditions. In phase two, when actual mining selectivity, sequence, and other practical design considerations are related in a direct simulation model to the optimum criteria found above, the maximum NPV invariably decreases. However, if it is still satisfactory (NPV greater than or equal to zero) then the maximum worth/ optimum design have probably been found in the first iteration. If, on the other hand, NPV is now unsatisfactory, then design compromises must be made and simulated, and the results rerun through the evaluation model. If several iterations fail to yield a positive NPV then the deposit is most likely unfeasible t for the forecast economic conditions used in phase one.

Jan 1, 1986

By Jan Leja

Surfaces of metal sulfides react readily with selected constituents of environment. Two types of reaction products may form: (1) primary, chemisorbed and hydrophobic surface products or primary hydrophilic surface products, and (2) secondary reaction products -- produced during continued oxidation-reduction processes. For flotation, the chemisorbed surface product and the secondary reaction products, elemental sulfur or metal xanthates, must provide sufficient hydrophobicity of the surface to ensure particle-bubble attachment.

Jan 1, 1986

The General Purpose Simulation System (GPSS) is a computer simulation language that has been used for simulations of open pit haulage operations since the 60's. It is easy to learn, simple to use, and has a block-diagram structure that is amenable to load-haul systems. However, due to its lack of flexibility, there are situations where another language should be chosen. This paper reviews the characteristics and capabilities of both GPSS and FORTFAN with regard to open pit shovel and truck simulation. The relative advantages and disadvantages are highlighted and a case study presented along with comparative results from two computer models (one written in GPSS and the other written in FORTRAN).

Jan 1, 1986

By D. A. Curry

This paper describes a study of the influence of non-normal loading on the indentation behaviour of single bit-teeth. Indentation experiments have been performed on a soft, isotropic limestone using both sharp and blunt 60 degree wedge-shaped indentors constrained to penetrate the rock at 0, 15, and 30 degrees to the rock surface normal. For both sharp and blunt indentors, the normal force required to produce a given normal penetration decreased as the offset of the penetration direction from the rock surface normal increased. The crater volume produced by a given normal penetration with the sharp indentor was largely independent of the penetration direction. In contrast, the crater volume produced by the blunt indentor was increased markedly by non-normal penetration at small penetration depths, because the threshold penetration for chip formation decreased with non-normal loading. The crater volume produced by a given normal force was significantly increased by non-normal penetration, and this increase was particularly pronounced with the blunt indentor. The energy required to form unit crater volume was correspondingly reduced by non-normal indentor penetration. A simple method for predicting the reduction in the rock's resistance to chip formation is outlined, which is supported by the experimental data. The implications of these findings for rotary drilling are considered.

Jan 1, 1986

By Tien H. Wu, Pinnaduwa H. S. W. Kulatilake

The concepts of conditional probabi1ity and geometrical probability are used to establish a relation between the probability density of the trace length and the probability density of the discontinuity diameter. The discontinuity is represented as a thin circular disc. A numerical solution scheme is used to obtain the probability density of the disc diameter from the probability density of the trace length. An example was used to illustrate the possibly large difference between the mean discontinuity diameter and the mean trace length.

Jan 1, 1986

By B. Pesic

The recovery of silver and gallium from flue dust with acidified thiourea solutions was examined. The studied parameters were temperature, particle size, thiourea concentration, acid concentration, and the presence of oxidants. The study of the extraction of these two metals was undertaken in sulfuric acid medium. Silver dissolution was dependent on all examined parameters, whereas gallium extraction was only dependent on the initial acid concentration. The experimental results suggest a new very efficient method for recovery of both silver and gallium. Almost complete recovery of silver and gallium can be accomplished within 90 minutes. A technological scheme for recovery of both metals is also proposed.

Jan 1, 1986

By K. C. Ko, M. D. Bunnell

The studied coal mi1e is an underground coal mine located in the northern Wasatch Plateau of central Utah (Figure 1) . Since operation began in 1981, in situ stress conditions have been encountered which differ from the assumed conditions utilized during early mine design efforts. Geologic structures also varied somewhat from those projected during initial geologic interpretations of the area. The encountered geologic conditions combined with the unusual stress conditions prompted a combined study of in situ stress and stress-related geologic structures. The study was conducted in two phases, with phase 1 consisting of detailed underground mapping and analysis of stress-related geologic structures to determine stress orientations from which they originated; and phase 2, consisting of over- coring two sites within the mine to determine present in situ stress orientations and magnitudes. GEOLOGIC ANALYSIS Three types of geologic structures have been encountered in the mine that act as indicators of stress orientations of the geologic past. Two of these structures, faulting, and igneous dikes, are directly measurable in the mine. A third type of structure, photolineation, was detected through remote sensing methods and shoe god correlation to roof conditions in certain areas of the mine. Faults Two major orientations of faulting have been encountered in the studied coal mine, including a system of N 80 W striking normal faults and a system of N 55 to 70 W striking oblique-slip faults. Only data collected from the oblique-slip faults were used for this study due to the fact that these faults offset the N 80 W faults wherever the two systems intersect, indicating that the N 55 to 70 W system was created by a more recent stress field. Figure 2 shows locations within the mine where data were collected from seven locations along oblique-slip faults. Data collection consisted of measurement of fault plane strike and dip, fault slickenside trend and plunge, and slip direction. The data are tabulated in Table 1. The fault data were then plotted on stereo nets to determine the stress orientations present at the td of faulting (Figure 3). The determined stress orientations are 32~0 included in Table 1. The stereo net plots show average principal stress orientations of: 1) [ ] plunge 1 degree. These data suggest that the N 55 to 70 W oblique-slip faults were produced by a nearly

Jan 1, 1986

By G. E. McClelland

Agglomeration techniques have been successfully applied to commerical heap leach cyanidation operations for the recovery of precious metals from low-grade ores, mine wastes, and tailings. The major parameters important for successful agglomeration pretreatment of these feed materials are discussed. Several commercial agglomeration-heap leaching operations are described. Two of the operations converted from conventional heap leaching to agglomeration-heap leaching after coventional heap leaching proved unsuccessful. Heap performance before and after agglomeration is discussed. A fairly recent operation that began production using agglomeration-heap leaching technology is also described. Two operations that processed milled tailings by agglomeration are discussed. The tailings feeds could not have been economically processed by means other than agglomeration-heap leaching.

Jan 1, 1986

By E. E. Jones

The lignites of Arkansas, Louisiana and Texas are typically described as muitiseam deposits which contain quantities of day and sand in thin lenses or in admixture with the fuel itself. These materials are often included in the run-of-mine fuel and can have very adverse effects in the end use. Since May of 1982 the Dow Chemical Co. has operated a pilot plant for the beneficiation of lignites. This facility has successfully removed sand, clays and petrified wood from the lignite producing a fuel comparable to or better than the selectively harvested run-of-mine materials. The design, operation and results from this plant were presented by J. H. Everitt at the 1984 Coal Technology Conference.

Jan 1, 1986