Search Documents

By T. J. Driscoll

The effect of coatings on the incendive properties of aluminum alloy 6061-T651 in air-6.4%CH4 was studied for collisions between rusted steel and both uncoated and coated projectiles with incident energies as high as 300 J (220 ft-lb) and velocities as high as 200 m/s (660 fps). These conditions were intended to simulate the rough handling of equipment in coal mines. The ignition probability using uncoated alloy projectiles increased with increasing relative humidity and appeared to be influenced by atmospheric ozone content. The incendive properties of both the uncoated and coated alloy depended on the type of rust used, but the dependence of the coated alloy was very different from that of the uncoated alloy. A number of coatings developed in the last 25 years were found to offer protection from ignition and to remain largely intact for occasional collisions or collisions randomly distributed over the coating surface, but probably not for repetitive collisions at any given point on the coating. These protective coatings utilize a hard anodized aluminum alloy surface coated with one or more layers followed by heat treatment of the coating. Coatings containing Teflon and MoS2 and thicker than 50 µm (2 mils) appear to be most effective.

Jan 1, 1987

By Rudolf E. Greuer, Xintan Chang

Mine fires have always been of great concern to mining engineers and their behavior has been studied for a long time. Although an abundance of observations exist, no satisfactory mathematical model for their interpretation and extrapolation has become known. The paper presented here tries to close this gap, making use of the laws of chemical kinetics, energy and momentum conservation. To overcome the mathematical difficulties, the fire zone is axially divided into segments and radially into sections, each one with an extension of only a few inches. Conditions in segments and sections are updated in time intervals of one second or less. To solve the large number of resulting equations, a numerical solution is performed. The model has so far been tried on timber fires. It confirms experimental observations on the ignition phases and equilibria of these fires.

Jan 1, 1987

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987

By J. T. Ryan, Wayne H. Griffin

Solutions to typical leaky ventilation circuits such as multiple entry headings and ventilation tube or brattice face ventilation are obtained using the discrete continuous simulation language SLAM II. While the continuous aspect of the language allows exact numerical solution of leaky systems, the particular discrete-continuous interface of this language is easily adapted to space varying geometry and flow parameters encountered in mine ventilation. The ease with which this simulation system is adapted to ventilation problems and the availability on personal computers encourage its wider application in the field.

Jan 1, 1987

By M. K. McMullen

Mineral Development Agreements (MDA?s) are a cooperative mechanism in Canada by which the federal and individual provincial governments can coordinate their scientific, techno- logical and market development resources in order to implement measures designed to stimulate mineral exploration and development by the private sector; the objective, ultimately, being to increase the mineral industry?s contribution to provincial economies. In the latest round of MDA?s, which was initiated in 1984, a significant number of planned activities relate to industrial minerals. This paper will describe the nature and importance of MDA's in Canada and will outline the wide range of activities taking place with respect to industrial minerals.

Jan 1, 1987

By L. W. Teal

The Paupers Dream Property is located in the northern Boulder Mountains, southwestern Montana, 30 km southwest of Helena. The property is situated in the central portion of the Butte-Helena gold belt, a NE trending lineament marking a zone of recurrent, late-Cretaceous to mid-Tertiary volcanic activity. Geology consists of a plutonic basement of late-Cretaceous quartz monzonite overlain by a pre-volcanic basal conglomerate and a complex sequence of Oligocene rhyolitic volcanics. Gold mineralization occurs in fracture-controlled quartz veins, silicified stockwork, and brecciated shear zones as auriferous pyrite, arsenopyrite, and disseminated free gold. An estimated 60,000 tonnes averaging 2.5 g/t was produced from the Porphyry Dike, Venus, and Paupers Dream Mines on the property. Current drill indicated reserves (May, 19861 are placed at 6,946,000 tonnes averaging 1.45 g/t gold.

Jan 1, 1987

By R. Dewey

WHAT IS AI? It's very hard to say. Most researchers and practitioners disagree with nearly any attempted definition, but most would agree that A1 does deal with the development of computer-related methods o f problem-solving. Artificial intelligence is a discipline which seeks to emulate human anatomy and/or thought processes by applying computer science, electronics, and mechanical engineering to the development of natural language processing, machine vision, robotics, and knowledge-based expert systems. Integration of these four fields will someday produce the robots of today's science fiction. A1 addresses problems of structuring large amounts of knowledge and representing relationships with rules and semantic frameworks rather than with mathematical equations. A1 is convergent rather than divergent - - conventional conputer applications use relatively small quantities of input to generate large output, but A1 generally reduces large amounts of information to establish a few major conclusions. The development of A1 has prompted greatly increased efforts on the part of scientists and engineers to understand just how humans think, organize information, approach problem-solving, and form conclusions. Some of the more exciting and possibly far-reaching advances in A1 are coming in this more-or-less soft-science area. Thirty years of A1 research (dating from a 1956 conference at Dartmouth College at which the term A1 was coined) has already spawned many widespread, almost ordinary, products: window graphics, hand-held controllers (mouse). function menus, etc., all in an attempt to make computers and people more compatible. WHAT IS AN ES? A1 can be used to develop EXPERT SYSTEMS, which are computer programs or systems which contain knowledge and rules by which problems can be solved. or at least by which possible solutions can be suggested for very complex problems. A1 can be used to better define problems so that solutions can be found. An ES is designed not to process numbers, but to process information according to rules and logic derived from actual practice and experience. WHY AI? WHY ES? Companies are increasingly aware of the value of accumulated knowledge and experience in designing, building, operating, and maintaining the increasingly complex or expensive physical plants in any business. As knowledge branches out and becomes more specialized, the accumulated learning of a veteran operator or manager or engineer becomes a scarce resource well worth preserving. EXPERT SYSTEMS offer a means of doing that, reinforcing, not replacing, human capabilities.

Jan 1, 1987

By J. Keng, S. T. Chen, T. M. Shih

Kwanyin Tunnel is presently the longest (7.7 km) railway tunnel in Taiwan. Due to heavy railway traffic, a pass-by station will be built inside the tunnel to increase the traffic flow. Since the concentration of toxic gases released by the locomotives may reach dangerous levels, a research program was conducted for the purpose of designing a ventilation system which could dilute and/or remove the toxic gases to maintain an acceptable pollutant level. The program consisted of two parts. The first part was field measurement during which the concentrations of pollutants and wind velocities were measured at various points inside the tunnel to acquire basic data regarding ambient air quality, piston effects for the different types of trains, and existing ventilation conditions. Weather data (temperature, humidity, atmospheric pressure, wind direction and velocity) were gathered at many stations, both on the surface and inside the tunnel. The amount of pollutants released by each type of locomotive for various conditions were also measured. The second part of this study involved establishing mathematical models for predicting the air quality of the various proposed ventilation systems. Three different models were used for this work. The first one is a piston effect model which assumes that the gases and air undergo immediate mixing inside the tunnel. The second one is also a piston effect model which assumes that the diffusion ability of the gases is zero. The third one is a conventional ventilation model which was used for natural and mechanical ventilation conditions. From the result of field measurement and mathematical model studies, a ventilation system was chosen with consideration of both ventilation effects and construction costs.

Jan 1, 1987

By J. A. Dille, J. P. Hand, J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Co. to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the company's main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received additional attention in recent years. An objective that no coal shipment should exceed any contract or company-imposed coal quality specification has been successfully met. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed.

Jan 1, 1987

By James M. Prudden, Jon C. Sprague

Valdez Creek Mining Co. properties consist of multiple intersecting paleo-placer channels containing appreciable quantities of coarse gold. Reverse circulation drilling, combined with geophysics, is used for both exploration and development reserve determination. Classical drill-blast-load-haul open pit mining techniques used for the 22,000 cubic yard per day production schedule required modification to compensate for arctic winter operating conditions. High wall stability problems within the glacial sediment overburden necessitated developing multiple dewatering methods and variable pit slope designs to eliminate unstable pit wall conditions. Processing mine run fluvial gravels utilized a classical winter protected screening plant-sluice box recovery system enjoying high metallurgical recoveries and zero discharge tailings disposal.

Jan 1, 1987

By William Mayrsohn

IMTRODUCTION The marketing aspects of a new precious metals property is often not considered until the mine actually begins production. At this point in time it is often too late or too expensive to change the mine's final product and not enough time to do an effective marketing program. MINE PRODUCT The rule for determining the mine's final product: The higher the gold and silver content, the greater return of metal at the lowest post-mining cost. . Dore Bullion: Most advantageous Advantages: - Highest return of metal. - Lowest refining cost per ounce of gold and silver. - Very compact and easy to ship in small quantities. - Easy to assay. - Assays between mine and refiner are comparable. - Melt losses are very small at the refiner. - Outturn of gold and silver 20-30 days for quick cash flow. - Gold/silver refiners can return or purchase metal soon after arrival at a nominal financing cost.

Jan 1, 1987

By John E. Urosek, Mark L. Mott, Gary E. Smith

One function of Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center's Ventilation Division is to provide assistance to MSHA enforcement and industry personnel for maintaining adequate fresh air to all areas of an underground mine. In fulfilling this objective, total mine venti1ation pressure-air quantity distribution on investigations are conducted to measure the air pressures and quantities necessary to describe and analyze the existing ventilation systems. Various ventilation parameters are calculated from these measured pressures and quantities. Some of these parameters are: pressure drop in intake and return airways, air leakage, percentages of air reaching active sections, average regulator drops, and fan pressures. The purpose of this paper is to present and compare values of ventilation parameters calculated from investigations at twenty underground coal mines.

Jan 1, 1987

By J. D. McKay

Continuous column flotation parameter testing, to improve operating methodologies, using coarse bubbles on fluorite ore from Nevada, revealed that retention time is the predominant factor affecting column flotation fluorite recoveries. Column height and feed injection location affected fluorite grades and recoveries because they affected particle retention times in the collection and cleaning zones. Other parameters tested, including froth depth, wash water addition, and axial mixing, showed varying results. Four defined zones within the column were found to have characteristic rates of upgrading per vertical foot. Fluorite-gangue separation was more efficient in a column than in a conventional cell at all particle sizes.

Jan 1, 1987

By M. J. Hart

Today, aggregate producers in the Denver Metropolitan area, herein defined as Denver and surrounding communities in Adams, Arapahoe, Boulder, Douglas and Jefferson Counties, are scrambling to secure their future reserves. The Denver market is somewhat unique among the larger metropolitan markets in that the source of needed aggregate for the future is very much undecided. 2. Present Aggregate Resources Presently, the annual consumption of aggregate resources in the Denver Metropolitan area amounts to approximately 16 million tons of sand, gravel and crushed stone of which the later accounts for about 20%. Based on population growth projections for the front range, by the year 2000 the annual rate of consumption for aggregate in the Denver Metro area could be in the 25+ million ton range.

Jan 1, 1987

By D. A. Rice, R. G. Swanton, A. May, O. C. Carter

As part of a cooperative effort between the US Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input from the phosphate industry, the conversion of phosphogypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: (1) thermal treatment to volatilize sulfur. and (2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1987

By P. S. Parobeck, T. F. Tomb, R. S. Ondry

From October 1980 through August 1982, surveys were conducted on 19 longwall mining operations to obtain data relative to respirable dust levels associated with particular longwall operations and occupations, to make recommendations for enhancing dust control, and, where applicable, to evaluate the effectiveness of new technology implemented to control dust. The paper summarizes the data collected during these surveys and, where possible, draws conclusions and discusses actions that can be utilized to reduce exposures to respirable coal mine dust on longwall mining operations.

Jan 1, 1987

By David J. Starbuck

For small precious metals mining to show a comeback a different perspective must be taken than that of larger mining companies. This perspective must be much the same as that of past successful smaller mining enterprises such as when the US had a need for Uranium. Abandoned mines and environmental concerns in older mining districts have discouraged many from entering with the attitudes of why try there if so many unsuccessful mines exist. A small mining venture can be successful there but must have a "think smart'' attitude. There must be a thorough understanding of deposits, utilization of advanced technology and a properly managed mining operation. "THINK SMART" MINING The small mine operator is usually looking for small high grade deposits, consequently, long term success depends on a series of small successful mining operations. The small miner must succeed right-off or credibility and future project funding will suffer. No veteran of even a few years in the mining industry needs to be told that a dollar spent on production today fails to yield as much as it once did. More efficient equipment and techniques have helped soften the problem, but there is little likelihood that a mining company can do much to control inflation, wages, regulations, or grade. That leaves the small miner to "think smart" as one area where operating dollars can still be stretched to produce more than they presently do (Gardner. 1981). In the planning stage of a mining venture, when most options are still open, the main controllable elements are market timing, deposit selection, cutoff grade, mining method, mine design, mining sequence, rate of production build up, process design, project financing structure, project management, and project ownership structure. During planning, optimum criteria can be established for each of these. Once a mine is in production, these options are foreclosed or at least severely constrained. The more thought given to a mining program using all information available the less the risk of encountering disabling surprises. Thus the intent of this paper is to suggest the "think smart" attitude most small mine operations use for long term success. If one looks at a number of successful mining ventures, whether large or small, there is a general logic most have followed to be successful. They have used proven exploration, mining and processing techniques along with economic evaluation and experienced personnel to improve their odds. LOGIC IN DEVELOPING A FEASIBLE VENTURE Most successful small mine ventures achieve positive cash flow as quickly as possible by seeking out those deposits which require the least time and expense on activities leading up to production. To do this they look for deposits that are the most accessible, easily investigated, mined and processed with the cheapest fundamental methods. The general sequence of events starting with district selection are deposit selection, preliminary feasibility, exploration, detailed economic feasibility, mine planning, development and production. Each successive step becomes more costly requiring intermediate decisions along the way. District Selection Small operations should look for known deposits which favor the occurrence of the type deposit sought rather than efforts in unproductive areas. Known deposits in developed areas have some advantages over remote areas: 1. More alternative methods of transportation are available. 2. A larger stable work force is available. 3. The area is usually more pro-mining. 4. Power, water, housing, technical services, skilled services, schools, recreation and shopping are available.

Jan 1, 1987

By Jerry Grott

Southwest Salt Company is solution mining the Luke Salt Body of probable late Miocene age. The discovery hole, from which the first core was recovered, was drilled in 1968. The deposit was encountered at a depth of 880 feet, and the bit was still in salt at the bottom-hole depth of 4,500 feet. The solar ponds, developed on land formerly dedicated to agriculture, have an annual capacity of about 90,000 tons. Because land values are very high, mining rates and procedures are governed by the need for near-saturated brine to minimize land requirements. Because of the frequency of dust storms, the salt operation uses a unique wet-harvesting method. Most inventory is kept in the ponds under brine and harvested only a few days before shipment. Studies of the nature of crystal growth and the distribution of windblown and brine impurities led to the development of procedures for processing salt of high chemical purity and low insolubles content. Chemical purity exceeds that of most salt produced in fuel-fired evaporators. Salt is shipped from Phoenix as tar east as west Texas and as far west as central California. Occasional shipments have been made to Hawaii and Alaska.

Jan 1, 1987

By Robert A. Jankowski, Jonathan Kelly, Edward F. Divers

Results for the first underground test of the ventilated drum in a U.S. coal mine are presented. Tests were conducted by the Bureau of Mines through a contract research program with Foster-Miller, Inc., to evaluate dust control effectiveness in a western mine and for gas control in a full scale laboratory facility. The ventilated drum is designed to reduce the amount of dust from cutting by drawing dust-laden air from the cutting zone through twelve water- powered "dust capture" tubes built into the shell of the shearer drum. High pressure water up to 1 12.48 kg per cm2 (1,600 psig), released from sprays, induces maximum airflow of 1.89 m3/sec (4,000 cfm) from the face side of the drum and provides cleaning for respirable dust and improved methane dispersion. At the gob side of the drum a deflector plate, attached to the cowl arm, turns the water spray and a proportion of the cleaned air back into the cutting zone. More than 50 ventilated drums have been installed to date in England, and their tests carried out on fixed height and single-ended ranging drum shearers have shown reductions in respirable dust of 60-80 pct, as compared with conventional wet cutting. The U.S. test on a double drum shearer showed slightly lower reduction.

Jan 1, 1987

By Alfred Petrick, Roger Dewey

INTRODUCTION Estimation of capital and operating costs for mines and mills has long been a necessary ingredient of feasibility studies, and though many practitioners have successfully used "rules of thumb" and factor estimating methods for many years, a great deal of work is usually required to prepare an initial estimate and/or to update or revise such an estimate. Development of comprehensive mining and milling cost models during the 1970's by the U.S. Bureau of Mines and by Canadian workers (O'Hara and Mullar) provided the basis for feasibility-level cost estimates, but the numerous equations and the apparent rigor and complexity involved in preparing a project estimate using these models has discouraged many, if not most, potential users. Their acceptance was also hindered by a broad misunderstanding by many engineers in the minerals industries who had little exposure to such procedures, and by a possibly inadequate level of explanation or documentation of the parametric approach to cost estimating. The preliminary nature of most databases, geologic/engineering/ and market, available to the engineer or analyst during the early stages of a mineral project is a universal problem. Basing corporate mega-investment decisions or even individual equipment selection decisions on the usual "SWAG’s has always been a risky practice, but in the current business environment, the "guesstimates" are almost 'verboten', and are certainly becoming antiquated with the advent of both the described models, the ubiquitous microcomputer, and the nearly-ubiquitous hybrid species known as the "computerized engineer". Engineers have almost always sought techniques of cost estimation that can be applied and justified when geologic and engineering information for a mining project is preliminary and incomplete. The answer, in some cases, is the "parametric" approach. Equations, based on actual, past experience are developed to relate capital and operating costs to major physical variables such as the rate of mining or milling, with modifiers for such details as mining method, process characteristics, methods of construction, or types of equipment . Cost Engineering Standards Five major types of fixed capital cost estimates have been defined by the American Association of Cost Engineers : 1. Order-of-Magnitude estimate based on previous cost data and minimal knowledge. usually a "ratio estimate" with no better than +/- 30% accuracy. 2. Factored or ratio estimate based on major equipment costs with probable accuracy in the 25 to 30% range. 3. Budget authorization or Preliminary estimate, based on sufficient project data to

Jan 1, 1987