Search Documents

By P. K. Songfack

The transport of slurry within the ball mill depends on the peripheral velocity and porosity of the ball charge. Residence time distribution and mill hold up are of-ten used as indicators of the mode of transport. In this work, the transport problem is tackled via direct simulation of the three dimensional motion of the ball charge. In doing so, the following quantities are calculated: (i) ball size distribution as a function of the distance from the feed end of the mill (ii) mean peripheral and longitudinal velocity and longitudinal velocity of balls of different sizes, and (iii) the spatial distribution of porosity within the ball charge. Hence, the problem of transport is handled as a motion of part of the slurry with the ball charge and part as hydrodynamic flow through the porous structure.

Jan 1, 1993

By Y. Guan

The dissolution behavior of silver and copper from silver/copper alloys in ammoniacal solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of composition of alloys, concentration of lixiviants, stirring speed and temperature on the overall dissolution kinetics has been studied. Silver / copper alloys of three compositions were used in this study. The atomic percents of silver in these alloys were 76.9, 46.9 and 24.1. The results on the rate of dissolution obtained for these alloys have been compared with that of pure silver and copper under the same testing conditions. A particular emphasis has been given to the galvanic effect on the overall dissolution rates.

Jan 1, 1993

By Kerry Spickelmier

With the dissolution of the former USSR and a welcoming of foreign, minerals expertise by a host of developing countries, a "new," more international, world of minerals is open to the mining industry. However, even in the new frontier, the old laws of nature still apply. For those attendees of the 98th annual Northwest Mining convention, the adage "survival of the fittest" commanded particular attention. Miners, engineers, geologists and other unique species traveled to Spokane in December to learn of adaptations they can make to assure, or at least prolong, their place in the mineral industry's land of the living. You have heard the tales of the spotted owl and the desert tortoise, but add to this endangered list the North American mining industry. During a session on international investment criteria, D. Silver of Balfour Holdings (Littleton, CO) blamed excessive environmental regulation, 1872 Mining Law revision and the anti-mining-and-business attitude of our government for migrations from and extinctions within the domestic mining population. "We've been on a death curve for some time," Silver said, "with a lower birth rate and a higher death rate. In the last four years, we've lost 60% of the gold producers in North America, and we're down to 110 companies. The entire industry has lost about 400 companies and is now down to 2800." Unreasonable regulation founded on emotion rather than scientific fact has been the chief cause of death, according to many of the convention speakers. B.J. Kennedy, president and chief operating officer of FMC Gold (Reno, NV), emphasized, "We have accepted a regulatory environment - but we oppose being strangled to death by unreasonable regulations."

Jan 1, 1993

By Tetsuji Hirato, A. J. Monhemius, Yasuhiro Awakura, G. W. Warren, E. Peters

An electrostatic pseudo-liquid membrane technique, in which extraction and stripping take place simultaneously in a single reaction vessel using an electrostatic dispersion, was applied to recover Ni(II) from aqueous 0.1 kg m-3 Ni(II)(as NiSO4) – CH3COONa solutions, and the Ni(II) ions were concentrated by a factor of 9 into an aqueous 1.0 kmol m-3 HCI solution using D2EHPA as an extractant at the applied voltage of 3.7 kV for the dispersion. When the process of ESPLIM proceeds favorably, the concentration of Ni(II) in the upper part of the organic phase of the reaction vessel is lower than that in the lower part. In addition, the concentration of Ni(II) in the organic phase of the extraction chamber is higher than that in the stripping chamber. For the stable operation of this process, the stripping rate must be greater than the extraction rate to prevent the excess accumulation of Ni(II) in the organic phase which leads to the poor dispersion of the aqueous phase.

Jan 1, 1993

By F. D. Wicks

This paper summarizes the direct operating cash costs for the Barrick Mercur open pit gold mine. A comprehensive, detailed system of cost management has been in effect for the life of the Mercur operation. This system provides the basic data for operations control and is the basis for drafting budgets as well as analyzing impact of change on operations costs. The ore body is complex geologically and metallurgically, requiring operators to pay close attention to mining and processing costs. The cost history provides data which enables analysis of changes in production levels, aging of the mine production fleet, and the impact of specific cost changes through time.

Jan 1, 1993

By J. A. Bradbury

N. A. Degerstrom, Inc. has constructed and operated a processing plant approximately five miles north of Soda Springs, Idaho for processing a byproduct phosphate treater dust from Monsanto's elemental phosphorus plant, also located in Soda Springs. The plant is designed to produce agricultural-grade phosphoric acid, gallium, and silver. The design capacity of the plant is 54.4t (60 st) of treater dust per day, which can produce 16,326t (18,000 st) of phosphoric acid, 6,600 kg of gallium, and 6,033 kg (194,000 oz.) of silver per year.

Jan 1, 1993

By Bruce W. Cavender

In an effort to lower production costs and improve profitability, mining companies have adopted a variety of management practices emphasizing productivity and cost containment. One set of practices that has been used successfully in the manufacturing and electronics industries is "world-class manufacturing" (WCM). It is applicable to mining as well. World-class manufacturing is based on the twin concepts of "just-in-time" inventory practices and total quality control. A few mining companies have implemented quality control programs that are similar to WCM in some ways and substantially different in others. This article considers the use of WCM in the processing environment, although the techniques are applicable throughout a mining operation. The article is also mindful of the variety of customers to whom mineral products are sold. Industrial minerals producers may sell brand-name products to specific customers with exacting requirements, while metals producers often sell their fungible output on a faceless commodity market. Customer requirements are emphasized in WCM, and so the range of these requirements must be recognized. World-class manufacturing In any milling process, specific goals are set for product and process characteristics - concentrate grades, minimum daily throughput, moisture content, etc. WCM has two overriding objectives: the reduction of deviation from these standards, and the reduction of variability in all aspects of the process and product. By definition, reduction of deviation also includes minimizing plant downtime for repairs or process changes. WCM plants use just-in-time inventory practices and total quality control. WCM plants use these techniques to simultaneously improve productivity and reduce costs.

Jan 1, 1993

By Thomas E. McNider

On July 20, 1990, a Spontaneous Combustion Control Plan was approved by MSHA for Jim Walter Resources, Inc. No. 5 Mine. The mine operated under the plan for twenty-nine shifts before MSHA revoked the plan. A total of fifty-five seals were constructed during the process of implementing the plan. The major difficulty in applying the control concept resulted from problems controlling leakage at the numerous seals. The number of seals was a direct consequence of attempting to merge the traditional bleeder system, used in all the Blue Creek Mines, with the bleederless system Jim Walter Resources proposed as a means of controlling the spontaneous combustion hazard. This paper discusses Jim Walter Resources experience with spontaneous combustion control and the new safety standard which applies to underground coal mines that demonstrate a history of spontaneous combustion and how this standard would apply to our No. 5 Mine. The new Ventilation Standards were published in the Federal Register on May 15, 1992, and scheduled to go into effect August 16, 1992.

Jan 1, 1993

By Michael G. Nelson

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993

By John Turner, David Carey

The Robbins Mobile Miner demonstrates the successful combination of hard rock excavation technology and the latest electronic control technology. The mobile miner, a partial face hard rock tunneling machine, features a fully integrated control system relying on a Programmable Logic Controller (PLC). This PLC controls all functions: tramming, steering, boom swing, cutting depth, conveyor operation, air scrubbers, hopper loading and unloading, etc. The machine is fully instrumented allowing the PLC to monitor the results of all commands on a continuous basis, to record data, to evaluate developing problems, or to shut the machine down if necessary. The paper describes the development of the Robbins - Pasminco automated mobile miner and early testing at Pasminco Mining's Broken Hill Southern Operations, New South Wales, Australia.

Jan 1, 1993

By J. Hanna, J. Jung

Researchers at The University of Alabama have recently developed a two-step method for the treatment of phosphorus sludge. The process includes the bulk removal of phosphorus by physical separation techniques followed by the remediation of the residual P4 in the sludge using a novel, wet, air-oxidation technique known as "HSAD." Tests made on electric furnace, phosphorus sludge samples have demonstrated that an essentially complete and fast removal of the contained P4 can be achieved by the HSAD wet oxidation treatment. Further studies were made to determine the applicability of the two-step process to sludges of different origins, pretreatments, storage conditions and P4 contents. The present work discusses the mechanisms and factors controlling the HSAD, wet, air-oxidation remediation approach.

Jan 1, 1993

Using a Mark IV surface force apparatus, adsorption of dodecylamine hydrochloride on mica has been studied at pH 5.7 in the presence and absence of octanol. With amine alone, the repulsive forces between mica surfaces are reduced due to charge neutralization and attractive hydrophobic force; however, the latter is of relatively short-range with its decay length less than 2 nm. In the presence of amine and octanol, the hydrophobic force becomes more significant, its decay length being extended up to 6.5 nm. The increased hydrophobicity in the presence of octanol is attributed to the co-adsorption of the neutral surfactant with dodecylamine, which increases the packing density of hydrocarbons on the mica surface. The increased hydrophobicity due to co-adsorption is reflected in the improved floatability of silica when using octanol as an extender.

Jan 1, 1993

By T. P. Smirnoff, R. J. Redmond, K .. N. Murthy

To minimize disruption to the Hollywood District of Los Angeles, a mined station using the New Austrian Tunneling Method (NATM) was developed. This paper presents the key factors contributing to the settlements and dynamic behavior of the unique binocular station design.

Jan 1, 1993

By M. J. Virnig, Peihao Qi, J. Brent Hiskey

The mechanism of gold uptake from iodide solutions by carbon has been investigated. Adsorption isotherms for gold and iodine were established. For activated carbon, approximately 300 mg of gold and 1000 mg of iodine were extracted per gram of carbon at maximum loading. Examination of loaded activated carbon particles by scanning electron microscopy reveals isolated patches of gold deposited on the carbon surface. High-resolution transmission electron microscopy shows that fine gold particles (1-4 nm diameter) are uniformly distributed within the carbon. Iodine was also observed throughout the matrix. The uptake of gold by carbon from iodide solution involves a combined reduction and adsorption process, where the gold iodide species is reduced to the metallic state superficially and adsorbed in the porous structure of carbon. A few experiments for the gold-chloride and gold-bromide systems were carried out for comparison.

Jan 1, 1993

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By M. D. Johnson

The San Andres mine, located in the western mountain region of Honduras, Central America, contains epithermal gold mineralization as disseminations, in quartz-chalcedonic veins and stockworks. Host rocks include a thick sequence of Cretaceous to Tertiary conglomerates, sandstones, rhyodacite tuffs and andesites. Mineralization is controlled by northwest and northeast striking, normal faults and fractures which dip steeply east and west. Currently, 500 STPD of 1. 93 Grams/MT gold ore is being open-pit mined from the conglomerate and andesite. The mine is at the west end of a mineralized zone that can be traced over an area of approximately 1.5 square kilometers.

Jan 1, 1993

By Jeanne A. Zimmer, Andrew B. Cecala, Edward D. Thimons

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U. S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations. INTRODUCTION Face ignitions are a concern for many U. S. longwalls and will continue to be until better control technology can be developed or until reliable and accurate knowledge can be provided as to when an explosive concentration is present. Figure 1 shows the number of reported U. S. underground longwall ignitions from 1980 to 1990. The number of longwall panels have remained relatively constant over this time period with 89 reported in 1980, compared to 96 in 1990. In spite of technological improvements in mining over the past decade, no significant reduction in the number of longwall face ignitions has occurred. One factor contributing to this is that the U. S. coal industry is mining gassier seams causing methane liberation rates on the average to be higher (Trevits, 1991; Grau, 1987). Another factor is the development and implementation of more reliable, heavy-duty longwall face systems that are generating higher production rates and higher methane liberation rates. Additionally, the average panel width in 1991 was 714 ft; a 44 pct increase from 1980 when faces averaged a width of 495 ft (Merritt, 1992). Increases in panel width also impact total face methane emissions. [ ] There have been substantial advances in control technology in the areas of methane drainage, methane containment, and methane dilution. In some mines, efforts to drain methane in advance of mining have proven effective, but geological conditions often preclude this approach (McCall, 1984; Ely, 1989). In other cases, ventilation air quantities of over 100,000 ft3/min and face velocities of over 1,000 ft/min have been implemented on longwall panels. Other operations have implemented anti-ignition spray systems which use water sprays behind each cutting bit to quench the hot streaks created from cutting noncoal materials (Courtney, 1990). Other control techniques, such as the modified shearer clearer system and ventilated drum, have been used to increase the amount of turbulence and ventilation around the cutting drums, thus reducing methane levels (Cecala, 1986; Divers, 1987).

Jan 1, 1993

The solution mining review did not arrive in time for publication in the May issue. The term solution mining is commonly used to refer to heap leaching, dump leaching, in situ mining and bore hole slurry mining technologies. The US Bureau of Mines is continuing with research in these areas. Commercial application of these technologies is progressing. There is an ongoing cooperative research project between the Bureau of Mines and the Santa Cruz Joint Venture to evaluate in situ copper mining at a field site near Casa Grande, AZ. The project is currently in the environmental permitting stage. The Bureau is preparing an environmental assessment for the project as part of the National Environmental Policy Act. The Bureau is also continuing with laboratory experiments to study the leaching characteristics of atacamite ore from the field test site, as

Jan 1, 1993

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

By A. J. Monhemius, R. G. Reddy, G. W. Warren, E. Peters

Thermodynamic solubility of chromium in pickling solutions (i.e., HF- HN03-H2O solutions) was determined as a function of HF and HNO3 acid concentrations at 298K. Pure Cr, AISI type 316 and 416 stainless steel were used in this study. The results showed that the solubility of Cr increased with increase in the concentrations of HF and HNO3 acids in solutions. The solubility of Cr increased in the order of pure Cr > 416 SS > 316 SS. The theoretically calculated Cr solubility data were in reasonable agreement with the experimental data.

Jan 1, 1993