Search Documents

By Jock McGregor, Deepak Malhotra, Leonard Harris

After more than 100 years, alkaline cyanide leaching of gold and silver ores, either directly in the case of oxidized ores, or after pretreatment of refractory ores by roasting, pres­sure leaching or bacterial leaching, remains the dominant r leaching method to extract the precious metals f om ores. Leaching with halides (chlorine, bromine and iodine) and with thiourea and thiosulfates is less common but prac­ticed in some cases to dissolve the precious metals both from ores and jewelry and electronic scrap. Cyanide solutions can contain from 1 ppm Au to 30,000 ppm Au. According to the source, i.e., agitated tank leach­ing, heap leaching, eluates from stripping activated carbon or waste electroplating solutions. Similar variations occur with silver which can have a profound influence on the recovery method. The presence of other elements in the leach solu­tions, particularly mercury and copper, likewise play an important role in the procedures required to recover the gold r and silver values f om solution. The same circumstances are found when lixivants other than cyanide are used to dissolve the precious metals. For decades, the preferred method of recovering gold and silver values from alkaline cyanide leach solutions was by zinc dust precipitation according to the Merrill Crowe process developed in the late 19th century. Finely ground gold and silver ores or concentrates were either leached directly or after roasting, in agitated tanks or Pachucas and subjected to solid/liquid separation by filtering or by treat­ment in counter-current-decantation washing thickeners (CCD). This solid/liquid separation step was often very dif­ficult especially when ores containing high quantities of clay were treated which caused filtration or thickening problems. Following testing and development by the U.S. Bureau of Mines (USBM) in the late 60s, the introduction of carbon­in-leach (CIL) or carbon-in-pulp (CIP) plants to recover gold and silver from leach pulps was one of the greatest opera­tional and cost saving improvements made in the industry in South Dakota and quickly spread around the world to be the most common process to recover gold and silver from cyanide solutions.

Jan 1, 2000

By M. Li, J. D. Miller

During the past decade, considerable effort has been made to develop improved flotation strategies for the sedimentary phosphate resources from Florida, particularly the dolomitic phosphate resources. New flotation equipment and alternate flotation strategies have been evaluated. These developments are reviewed for both traditional siliceous resources and future dolomitic resources. Most process strategies involve variation in the reagent sequence and/or the use of depressants/dispersants. Further research and development efforts in flotation technology are needed to increase flotation plant capacity by elimination of the conventional double float process, to improve the recovery of coarse phosphate, and to achieve the desired selectivity with respect to carbonate minerals, particularly dolomite.

Jan 1, 2000

By R. Fred Pena

The Tower Mill has proven to be a grinding machine with a demonstrated application flexibility. Variations in applications have proven to be numerous. This mill was originally intended for fine grinding applications. Subsequent testwork and installations have demonstrated the mill can be utilized in place of ball mills as secondary mills. The following lists a few of the circuits tested: 1. Tower Mill secondary receiving feed from a primary SAG mill grinding stage. 2. Tower Mill as tertiary grind unit following a rod mill/ball mill. 3. Tower Mill as secondary grind unit following a primary ball mill. 4. Tower Mill as a limeslaker. 5. Tower Mill grinding as a primary unit taking limestone crusher discharge. Applications demonstrate the mill is energy efficient and is sensitive to the following consideration: 1. Circuit chosen. 2. Top size of feed. 3. Product size required. 4. Classification equipment performance. 5. Media size required. 6. Media type required.

Jan 1, 1986

By V 9. 0 / 300 dpi

In the time period from the early 1980's to the present, longwall roof support technology has evolved tremendously. Chock supports and caliper shields were replaced by 2-leg or 4-leg lemniscate shields. The lemniscate linkage for which the support is named offers numerous advantages to the sup-port both as a fabricated structure and to its performance in the mining application. The hydraulic system, which is the dynamic element of the roof support, was essentially unchanged in early lemniscate shields with the exception of the complexity of additional hydraulic circuits to power a canopy tilt cylinder and canopy side-seals. The control of these fluid-powered functions was provided by direct manual control of valves energizing individual functions onboard the roof-support or the adjacent roof-support. This control valve-gear was comprised of multiple individual valves arranged in a "bank" or integrated into a single hydraulic distribution block with a single operating handle to select any independent function.

Jan 1, 1993

By Fred T. Towne

There are a number of air classifiers manufactured throughout the United States and the rest of the world. The classifiers manufactured by Alpine, A. G. of Augsburg, Germany, are unique in their abilities. It is this uniqueness that I wish to delve into and in this respect we will limit this discussion primarily to the classifiers as manufactured by Alpine. It has been reported in the past that these classifiers were introduced into the. United States in the late 50's. Until the introduction of the Alpine Classifiers, air classification seldom produced a satisfactory fractionation of a product below 45 microns (325 mesh) or above approximately 22 mesh. It has been a common practice to classify fine materials which used water as a carrier medium The use of centrifuges are today producing thousands of tons of finely partitive powders in the very small particle size range. The use of centrifuges in connection with wet grinding mills has increased the rates of production of these mills considerably.

Jan 1, 1965

By S. C. Tadolini

The use of resin-grouted cable supports to control large ground movements in several types of underground mines has increased substantially since being introduced in 1991. Cables offer several advantages over traditional support systems, having large support capacities coupled with the flexibility to be used in low openings. Cable slings have been designed to be installed on-cycle using no-spin technology or a two-piece unit that can be placed with hand-held drilling equipment. Additionally, yielding cable supports have been developed and are being used to control large amounts of movement in coal and evaporite deposits.

Jan 1, 1998

By Takahide Wakamatsu

In Japan all the complex sulfide ore deposits of base metals have been developed as underground mining. The underground mining cost is extremely high as compared with open pit mining case. Therefore, in milling section of base metal mines, technical advance for maximum recoveries of valuable constitutents in ore has been required all the time to utilize as much ore mined as possible. At present, in mill plants treating "Kuroko", complex sulfide ore, concentrates of copper, lead, zinc, pyrite and barite are produced, with gold and silver contents in the copper, lead, and zinc concentrates being estimated as extra profit. As in the case of Kuroko milling plants, gold and silver contents in the lead and zinc concentrates of lead-zinc ore milling plants are also varuable from an economical viewpoint. Silver content is very high in Kuroko crude ore as well as lead-zinc ore.

Jan 1, 1982

By James Wm. White

Computer based dispatching in open pit truck haulage operations yields many benefits of current interest to mine management. The key tangible benefit is a substantial productivity increase with a given fleet of equipment or, alternately, a significant reduction in equipment required to meet production quotas. Other tangible benefits, depending on the operation, include minimizing rehandle, meeting several blending constraints simultaneously and ensuring a target plant feed rate. Intangible benefits include production forecasting, performance comparisons of trucks or shovels of different manufacture and extensive on-line report generation. Recent advances in mini and micro computer hardware and software and solid state electronics permit design and implementation of system features not feasible even a few years ago. Here we discuss many of these recent developments with emphasis on system aspects and dispatching algorithms.

Jan 1, 1983

By R. Robertson

Dense medium cyclones are the preferred means for cleaning 112 in. x 14 Mesh to 28 Mesh (12.7 mm x 1.0 mm to 0.6 mm) raw coal and are becoming a common choice for cleaning raw coal from a nominal top size of 2-1/2 in. to 3 in. (63.5 mm to 76.2 mm) down to 14 Mesh to 28 Mesh (1.0 mm to 0.6 mm). During the last ten years, dense medium cyclone circuitry design has undergone changes which have combined to improve process efficiency. This paper describes these improvements and compares present day design with the design used prior to the mid 1980's. Improvements in the following areas are described: Raw coal desliming, cyclone configuration, drain and rinse applications, dilute medium circuitry, and instrumentation and control.

Jan 1, 1997

By L. Watters, R. Terry, D. Placha

Dense medium cyclones are the preferred means for cleaning 1/2 in. x 14Mesh to 28Mesh (12.7 mm x 1.0 mm to 0.6 mm) raw coal and are becoming a common choice for cleaning raw coal from a nominal top size of 2-1/2 in. to 3 in. (63.5 mm to 76.2mm) down to 14 Mesh to 28Mesh (1.0 mm to 0.6 mm). During the last ten years, dense medium cyclone circuitry design has undergone changes which have combined to improve process efficiency. This paper describes these improvements and compares present day design with the design used prior to the mid 1980's. Improvements in the following areas are described: Raw coal desliming, cyclone configuration, drain and rinse applications, dilute medium circuitry, and instrumentation and control.

Feb 24, 1997

By Donald R. East

For many years there has been increasing pressure on mining companies, not without some justification, to design tailings storage facilities which guarantee some degree of protection against process solutions entering local groundwater and surface water flows. A fairly straightforward approach to achieving this has been to design conventional water-retaining type structures, and this has often been reinforced by the need to store large volumes of process water and seasonal run-off within the tailings facility. The conventional design uses naturally occurring geological barriers and a conventional embankment with possibly a grout curtain, or artificial barriers around the entire facility, using either imported low permeability soils, admixtures, or synthetic liners. While these approaches may achieve the primary objective of minimizing seepage, various other factors should be considered. Firstly, by depositing the tailings slurry in a sub-aqueous manner, the tailings, especially if relatively fine grained, will settle to very low densities and little or no on-going consolidation may occur over the operating life of the mine, There have been many cases where measured pore pressures within the tailings mass equal the total overburden stress, i.e., no consolidation and no strength, many years after decommissioning.

Jan 1, 1998

By C. N. Bensley, S. K. Nicol

The major developments in fine coal processing in Australia are reviewed. Emphasis is placed on the approaches taken by various Australian coal producers to improve the recovery of the coarse size fractions (minus 0.5 plus 0.25mm) and upgrade the selectivity of flotation at ultrafine sizes (minus 0.075mm). The effects on fine coal preparation of flotation circuit changes, the influence of physical and chemical variables on coarse coal flotation and the impact of spiral concentrators and column flotation, are discussed. Reference is also made to the development of oil agglomeration technology for the treatment of fine coal refuse and some of the factors which have led to its current demise.

Jan 1, 1988

By I. Weir-Jones

[Currently the cost of carrying out 'in situ' geotechnical investigation programmes or installing and operating monitoring systems at construction or mining sites is rising var." rapidly. This is primarily because of our ever increasing labour rates. As a result of this problem efforts are no,, being made develop techniques for the economical; collection of large quantities of geotechnical data relating, to such problems as done stability evaluation, the behaviour of underground openings, or 'in situ' testing procedures. The efforts to reduce the labour content. are particularly apparent in those procedures which have traditionally been manpower intensive e.g. 'in situ' permeability testing where an entire drilling crew and their associated eguipment have been on standby while testis has been carried out; or data collection in underground construction operations where much tine is typically wasted obtaining or maintaining access to instrument sites. In an attempt to illustrate one specialist consulting company's approach to the problem of reducing investigation costs, this rarer examines four recent developments in the field of geotechnical investigation and monitoring which have come about during the last two Years as a result of cur research and development programme. Although these techniques and devices have been developed for specific projects, they all have broad applications in the geotechnical field and they are indicative of the direction in which this company feels developments will take place.]

Jan 1, 1975

By G. Belardi, N. Sheau, P. Plescia, F. Veglio

A study was conducted to assess a new wet gravity-separation machine, identified as the Multi-Gravity Separator(MGS). Chromite fines, obained from an Albanian chromite and olivine ore and containing 23% Cr2O3 and 18% SiO2, were used in the study. The first step was to determine the influence of various operating parameters. The study indicated that the most important variables for the MGS are rotational speed, tilt angle and shake amplitude. The best treatment conditions for the ore were then identified by investigating a series of circuits designed to produce a marketable product. In open circuit, a concentrate containing 50% CI-203 was obtained with a recovery of 72%.

Jan 1, 1996

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral-property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive-industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN `01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN '01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB were expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2003

By T. R. Ellis

A number of important international events took place in 2001 in the development and evolution of mineral valuation standards internationally. In Canada, the CIMVal Committee released a draft discussion paper for public and industry comment on principles to guide the development of the planned Canadian mineral property valuation standard. The International Accounting Standards Board (IASB) received comments on its Extractive Industries Issues Paper. IASB will decide whether the financial statements of public mining and petroleum companies will be allowed to provide the value of mineral and petroleum assets on a current value basis instead of an historic cost basis. The author led the Extractive Industries Task Force of the International Valuation Standards Committee (IVSC) in developing its submission to IASB. IVSC intends to develop an extractive industries valuation section for its International Valuation Standards, which could support the planned IASB standard. In Australia, AusIMM has carried out an in-depth review of its highly regarded VALMIN Code. The AusIMM's MICA subdivision organized the VALMIN ‘01 Conference in Sydney, Australia, with a range of international and current issues papers published in the VALMIN ‘01 book. Considerable support for the IVSC initiative was evident at this conference. The results of the review of the extractive industries submissions to the IASB are expected to be released in early 2002. The CMMI Congress in Cairns, Australia in May 2002 is likely to prove to be an important forum for continued discussion of the development and implementation of international standards and qualifications for mineral valuation. The outcomes and implications of these events are discussed.

Jan 1, 2002

By Paul F. Thiele

The mining industry of Georgia, while not as large as in some other states, is still an important part of the economy. Total value of mineral production in 1966 was $148.6 million.l/ Clays and stone produced the most income, Other minerals included sand and gravel, iron ore, mica, talc, barite, bauxite, cement, feldspar, kyanite, peat, and rare-earth metals, titanium and zircon concentrates. Georgia ranks first among the states in production of kaolin, second in fuller's earth and rare-earth concentrates, third in bauxite and kyanite, fourth in barite and ilmenite, and fifth in feldspar. It is quite likely that phosphates will one day be mined in the south eastern part: of the state, and that alumina will be produced from the extensive kaolin deposits in the central part of the state.

Jan 1, 1968

By L. B. Rothfeld

Two new coal use technologies are on the verge of commercial acceptance by the utility industry: atmospheric fluidized bed combustion (AFBC) and gasification combined cycle (GCC). Generating plants under construction or in planning will replace older pulverized coal (PC) boilers or substitute for new PC boiler capacity. This paper reports recent developments in the commercialization of AFBC and GCC, emphasizing the potential impact on the coal mining industry. The influence of coal quality characteristics on fuel selection is explored by means of preliminary economic calculations for different coals and competing fuels.

Jan 1, 1987

By Leonard B. Rothfeld

For many years, pulverized coal (PC) boilers in utility power plants have been the dominant market for domestic coal. Today, two new coal utilization technologies challenge the PC boiler's dominance. Atmospheric fluidized bed combustion (AFBC) and "coal gasification/combined cycle" (GCC) stand on the verge of commercial demonstration in the utility environment at a scale of 100 MW. Developed over the past decade, these technologies respond to the demands for cleaner ways to burn coal and for more flexibility in fuel supply. In the near term, these are the "clean coal" technologies most likely to have a significant impact, because they are ready for commercial application. As for environmental acceptability, consider that just a few years ago one of the environmental slogans was "no coal in California." Indeed, the only large quantities of coal above ground in California at that time were in transit on the way to Asia. Today, thanks to new technology, we can point to two operational coal-burning plants in California and one in the works: * Cool Water GCC demonstration plant (100 MW) * California Portland Cement AFBC commercial cogeneration, near Riverside (190 000 lb/hr steam) * Energy Factors AFBC commercial cogeneration at Stockton, to be operational 1988 (44 MW)

Jan 1, 1987