Search Documents

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Cameron Mitchel

Brow hazards are a significant concern in coal mine ribs and form when weak coal sloughs out of a rib face and exposes an overhanging block of more competent rock or coal. Of 36 rib failure fatalities in the last two decades, 36% resulted from rib brow failures. This highlights the need to better understand the mechanisms driving brow formations and failures to mitigate this hazard and eliminate potential fatalities. The research team at Missouri S&T worked to enhance the current CPRR system and include the potential for these brow hazards. We employed physical modeling methods to build a scaled model from critical brow cases observed in the field. The dimensions and properties of the models were scaled down by 14.4 times from the field cases. The results of the physical modeling efforts were used to assist in calibrating distinct element numerical models vital to understanding brow formation and failure mechanisms. Subsequently, three physical models were created and tested to provide data on an otherwise impossible-to-capture event at the field scale. The results of these tests provided formed brow dimensions that agree well with those observed at the field scale. The brow dimensions were 1.25 inches deep into the rib, equivalent to 1.5 feet when scaled up. Similarly, the numerical modeling efforts provided good agreement by capturing a brow forming 1.55 inches deep into the rib. The physical model results further validate the applicability of physical modeling efforts for capturing otherwise difficult and dangerous phenomena in a controlled lab setting.

Feb 22, 2026

Previous models describing the aggregation of polymer coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called ?active? sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1987

By A. McCombs

Previous models describing the aggregation of polymer-coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called "active" sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1988

By A. Yehia, M. I. Al-Wakeel

Flotation behavior, of magnesite and dolomite pure minerals was studied separately. Rice bran oil (a source of fatty acid ) was used as a collector for both minerals . The aim of this study is to find a separating zone in the flotation of these pure minerals to be used in the separation of their mixture. Factors affecting the flotation process, such as pH and collector, were studied. It was found that magnesite can be separated, from its mixture with dolomite, in the pH range of 5-7. At this pH range flotation recovery of dolomite reaches~98% where magnesite reaches ~20% only. Besides, the effect of collector concentration on the flotation shows that the separation of magnesite from dolomite is feasible at a collector concentration of 3x10-4 M. At such concentration, dolomite recovery reaches ~98%, where magnesite reaches 25%. The differences in the flotation behavior of dolomite and magnesite were investigated by studying the adsorption isotherms of rice bran oil on magnesite and dolomite surfaces. The adsorption study indicates that while there is an excessive adsorption on dolomite surface, the adsorption density on magnesite was restricted to be lower than monolayer capacity. The adsorption behavior of dolomite and magnesite was discussed in the light of their solubility and crystal structure. It was found that due to the higher solubility of dolomite than magnesite, Ca2+ and Mg2+ ions are available and more reactive on dolomite surface increasing collector adsorption. In addition, it was indicated that dolomite mineral has a crystal lattice structure more compatible to the geometry of the fatty acid carboxylic group than magnesite. However, the adsorption of collector on dolomite surface is more compact and more regular than on magnesite surface.

Jan 1, 2000

By M. Misra

A sample of thorium-contaminated soil from Kirtland Air Force Base (AFB) was subjected to froth flotation for removing thorium contaminants. A series of flotation tests were conducted to screen and evaluate the reagents. Among the collectors used, sodium oleate exhibited to show the promising results. Preliminary tests showed that a concentrate having activity as high as 5300 pCi/g can be obtained from the contaminated feed soil having activity 800 pCi/g. The volume reduction obtained was 89% and the activity recovery in the concentrate was 68%. The paper discusses the physico-chemical characterization data and the potential physical separation decontamination schemes for the thorium contaminated soils.

Jan 1, 1996

By Victor S. Sazhin, Alexander Kostenko

The hydrochemical method, which is based on the separation of aluminium oxide and silicon oxide by the hydrothermal decomposition of aluminosilicates by alkaline solutions in the presence of calcium oxide, can be effectively used for the complex processing of high-silicon aluminium ores. In this case, the silica is bound to a slightly soluble compound: Na20.2Ca0.2Si02•H20 (under the conditions: [&k]= 9, CaO/SiO2 = 1.05, alkali concentration in the solution: over 300 g/l Na20, T = 240...300 °C). If alkaline solutions of 100...150 g/l Na20 concentration are used, Ca0•SiO2•H20 or 2Ca0•Si02.0.5H20 compounds, depending on calcium oxide dosage, are formed at 280...320 °C. New methods for the crystallization of Na20.Al203.2.5H2O from concentrated alkaline solutions rand low-concentration solutions are proposed to isolate aluminium from solutions. The hydrochemical method, which involves no sintering process allows one to decrease the expenditure of heat by a factor of two, to reduce the investment and to exclude the pollution of the ambient air by dust-laden gases. The expansion of the raw-material resources base of

Jan 1, 1984

By T. E. Bernard

Occupying a refuge alternative (RA) is an accepted practice in mine fires and explosions when escape is not feasible. MSHA has promulgated a final rule on refuge alternatives that includes a recognition that thermal environment is an important consideration. To this end, an environmental index was specified. The question remains about how to test a refuge shelter to demonstrate that it meets the final rule. The analysis followed five activities: A. Provide an estimate of heat generated by an individual refuge alternative occupant; B. Evaluate the Steadman Apparent Temperature criterion of 95°F; C. Discuss simulations based on body temperature or skin temperature limits; D. Suggest method of simulating human heat generation during refuge occupancy; and E. Suggest alternative methodologies/criteria for evaluating heat and humidity survivability inside a refuge alternative.

Feb 27, 2013

By Charles Fisher

When considering the biodiversity of fauna endemic to hydrothermal vents or hydrocarbon seeps one must consider not only the numbers of unique species, but also the physiological diversity (and potential biochemical/physiological uniqueness) of the fauna. The deep ocean ridge system is home to some of most extreme animal habitats found on Earth. In addition to the high pressure, low temperature, and lack of light characterizing the deep-sea in general, hydrothermal-vent environments are characterized by toxic chemicals and temperatures that would be hostile to most other animal life. Perhaps even more challenging than the absolute levels of chemicals, dissolved gases, and temperature with which vent animals contend are the extreme gradients in time and space of all of these parameters. For example, temperatures around some vent animals can fluctuate from ice-water to hot-tub levels over seconds and can exceed 350°C only inches away. Specially adapted animals not only tolerate these conditions, they often thrive under them. As a result, the biomass of many deep ocean ridge ecosystems rivals that of coral reefs and tropical rain forests. In the Gulf of Mexico, hydrocarbon seepage through the sea floor driven by salt tectonics results in environments that are geologically very different from hydrothermal vents, but are geochemically similar enough that closely related animals are found in the two habitats. This includes seep mussels, clams, shrimp, worms, and other animals whose close relatives are found in hydrothermal vent environments. Although many aspects of the biology of the animals from the two environments are very similar, there are also significant differences in their life histories and physiologies that reflect the fundamental differences in the geology of their habitats.

Jan 1, 2008

By C. Vasilescu

Phytotechnologies use plants to remediate various media impacted with different types of contaminants. These technologies can be implemented either in situ or ex situ. The affected media in which phytotechnologies can be applied include soil, sediments, groundwater and surface water. They are best applied at sites with shallow contamination of organic, nutrient, or metal pollutants that are amenable to one of five treatment options: phytoextraction, phytotrans-formation, rhizosphere, bioremediation, phyto-stabilization or rhizofiltration. Phytoremediation can be used along or, in some cases, in place of mechanical cleanup methods. Phytoremediation can be used to clean up metals, pesticides, solvents, explosives, crude oil, polycyclic aromatic hydrocarbons and landfill leachates.

Jan 1, 2006

By M. Guzman, M. Romero, S. Bravo-Thais, M. Flores

The phytoremediation method is proposed to recover valuable metals from polluted soils. In this sense, the objective of this research is to determine if it is possible to use native plants in the recovery of precious metals from abandoned mining liabilities. The tailings samples containing Au and Ag were acquired from the northern region of Peru. Two native plant species, Stipa Ichu and Cortaderia Nitida, were used. Results show that Au was recovery around 19% (1.52 mg/Kg) and 25.43% (1.78 mg/Kg) by using Stipa Ichu and Cortadeira Nitida, respectively. Besides, Ag had a better recovery in the Stipa Ichu reaching a value of 6.83% (0.628 mg/Kg); in contrast, Cortadeira Nitida had an efficiency of 3.6% (0.814 mg/Kg). Bioaccumulation, bioconcentration and translocation factors were calculated by determining the concentration of precious metals in the roots and aerial parts of each plant. Results show that Stipa Ichu had a greater capacity of hyperaccumulated Ag compared to Au; while Cortaderia Nitida tended to have a better performance for Au. In conclusion, both plants are recommended for phytoremediation of mining liabilities.

Feb 1, 2023

By M. Guzman, S. B. Thais, M. F. Obispo, M. R. Arribasplata

The impact generated by old abandoned mines in Peru have produced mining environmental liabilities, which can generate an impact on the environment. In the search for long-term sustainable solutions, Phytoremediation is presented as an interesting alternative, since it allows the use of Peruvian native plant species for the accumulation of heavy metals. In this paper, we present the results of native high Andean species: Stipa Ichu and Cortaderia Nitida. The final metal concentration in the aerial parts and in the roots of each plant show that Stipa Ichu is more efficient to recover Fe, reaching almost 278 times its initial value. In the same way, this plant is efficient to remove Zn, Cu and Cd, reaching maximum values of 64, 39 and 12 times its initial concentration respectively. Cortaderia Nitida turned out to be more efficient to recover Fe, Zn, Cu and Cr, with highest recovery of 250, 117, 39 and 13 times its initial value respectively. Finally, based on translocation factor, Stipa Ichu has better capacities of hyperaccumulation of Fe, Cu, Zn, Pb and Cr. Cortaderia Nitida only shows hyperaccumulation of Cr.

Mar 2, 2022

By Felicia F. Peng

Flotation process is particle hydrophobic surface-based separation technique. To improve the essential flotation steps of collision and attachment, and reduce detachment probabilities between air bubbles and hydrophobic particles, a selectively designed cavitaion venture-tube can be used to generate very high numbers of pico-nano bubbles to flotation column. Fully embraced by those high numbers of tiny bubbles, hydrophobic particles are readily attracting those tiny bubbles to their surfaces. The results of column flotation of Pittsburgh No.8 seam coal are obtained in a 50 cm ID and 162cm height flotation column equipped with static-mixer and cavitation-venture tube, using kerosene as collector and MIBC as frother. Design of experiment procedure combined with statistical two-stepwise analysis method are applied and attempted to made the optimizing the grade and recovery. The effect of independent variables on response has been explained. Combustible material recovery of 85-90% at clean coal product of 10-11 % ash are obtained from feed of 29.6% ash, with reduced amount of frother and collector than that used in conventional column flotation. The column flotation process utilizing the pico-nanobubbles can also be extended to the lower limit and upper limit of particle size ranges for better recovery minus 75 µm and 300-600 µm, respectively.

Jan 1, 2013

By P. J. Rua

The Piedras Verdes copper mine is a new run-of-mine (ROM), heap leach, solvent-extraction/electrowinning (SX-EW) operation located 21 km (13 miles) north-northwest of the town of Alamos in the state of Sonora, Mexico. The Piedras Verdes copper mine is wholly owned by Frontera Copper Corp. (FCC), a Canadian corporation, through its 100 percent beneficial interest in Cobre del Mayo S.A. de C.V. (CDM), a Mexican registered company. The January 2008, minable reserves were estimated to be 193.6 Mt (213 million st) at a grade of 0.36 percent copper. The overall recovery of total copper was estimated to be 61.9 percent. The property has an additional 17-year life and is designed to produce 31.7 kt/a (70 million lbs/year) of cathode copper. Construction commenced in early October 2005. The first copper cathode was produced 12 months later at a total capital cost of $100 million. Elevations at the site range from 150 to 300 m (490 to 985 ft) above sea level. The area has excellent infra-structure in the form of towns, power, water, roads, rail, airfield and access to the deepwater port of Guaymas (Fig. 1). The surrounding area is also famous for its numerous polymetallic (lead, zinc, copper, silver and gold) epithermal veins. Some of these were mined for more than 200 years and provided the wealth on which the town of Alamos was built. The original village of Piedras Verdes was located in the area of the proposed openpit mine and, consequently, it was necessary to construct a new townsite 6 km (3.7 miles) to the south before project development could commence. The new town site (Fig. 2), complete with power and water supplies, roads, sewer system, schools, clinic and recreational facilities, was completed and occupied by 49 families in September 2005. CDM received its remaining permits from the Mexican environmental authorities on Sept. 20, 2005. This enabled the company to proceed with full-scale development. CDM owns or controls 27 mining concessions covering the resource. Surface rights to the Piedras Verdes project were controlled by four Ejidos (communal agrarian and/or ranching societies) and five individual landowners. CDM has acquired all surface rights necessary for its mining operations and associated facilities either through outright purchase or long term lease agreements.

Jan 1, 2008

By Brian Fulcher, Michael Bell, Shimi Tzobery, Werner Burger, John Bednarski

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft3/sec) of water into Southern California. The 13 km (8-mile) tunneling project is well underway and consists of two, 5.8 m (19-foot) diameter TBM bores through extremely variable geological conditions. The tunnels lie near the base of the San Bernardino Mountains and several significant faults including the San Andreas Fault run within one kilometer (0.6 miles) of the tunnel alignment. Numerous other significant faults cross the tunnel alignment and water pressures in the tunnel have been recorded as high as 20 bar (300 psi). This paper describes some of the problems and challenges encountered and the solutions implemented to advance the two hybrid TBMs under conditions that ranged from hard rock with no water inflows to full-face granular material under 10-bar pressure and in excess of 32 l/sec (500 gpm) inflows. Due to the range and severity of ground and water conditions actually encountered, the Owner-Contractor-Designer team eventually found that adjusting the means and methods to be more responsive—virtually on a day-by-day basis—was needed to suit the conditions

Jan 1, 2007

By David P. Keller, George Podolsky

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The world production of iron oxide pigments is estimated by the authors to be between 350 and 400 kt. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test which now has some 20,000 years of exposure. In addition to abundance, iron oxides (about 7% of the earth's crust) have the advantage of low cost, permanency, and are non- toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when these properties were desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States, the combined production of natural and synthetic iron oxides produced sales of over $97 million in 1980 (Spimad, Jr., 1980), increasing to $138 million by 1990 (Templeton, 1990) NOMENCLATURE With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products that are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a competitive commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and are able to command a premium price over iron ores used for steel manufacturing. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary particles are produced as opposed to the use of comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1994

By Y. Q. Zhang, S. S. Peng

Numerical modeling was used to design the pillars and bolting plan for a mine with weak roof and multi-seam stress condition. Previous mining experience, pillar/roof yielding and in-situ horizontal stress were considered in the models. By modeling the upper seam yielding and vertical stress transfer, a multi-seam influence zone was obtained. Appropriate pillar sizes were designed for conditions with and without upper seam stress influences. Roof support for the track and belt entries, using fully-grouted resin bolts and cable bolts, was proposed and implemented in the model. The bolting plan was evaluated under the weak roof condition.

Jan 1, 2004

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

By D. Krzyszton, P. Czaja

Mining explosions in rocks originate stress waves of great intensity, which crush the surrounding rocks and are then propagated as a seismic wave. Seismic waves are the cause of dynamic loading of pillars and their subsequent destruction. In calculating safe dimensions for inter-room pillars, not only the stresses conditioned by overburden pressures should be taken into consideration, but also the dynamic stresses caused by explosion. This is of particular importance for pillars with great specific acoustic impedance which have been destroyed mainly by the reflected seismic wave. It is possible to take dynamic loading into consideration in the calculation of pillars when the parameters of the propagation wave, the dynamic elastic constants of rocks, the strength properties of rocks, the strength properties of rocks subjected to dynamic loads and the parameters of the blasting charge are known. An example of the calculation for the safe width of an inter-room pillar subjected to the seismic effect of an explosion is given and the possibilities of reducing the dynamic loading of pillars are discussed.

Jan 1, 1982

By K. F. Unrug

Martin County Coal Corporation is located in Martin County, Kentucky in the Appalachian coal fields, near the West Virginia border. The total leasehold covers more than 33 000 acres. Total annual production at Martin County Coal Corporation is currently 2,500,000 tons, but in certain years exceeded 3,000,000 tons. Approximately 45 percent of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal Corporation's work schedule consists of 240 days/year, two nine-hours shifts/day.

Jan 1, 1991

By C. Haycocks

The Appalachian coal fields contain many mineable contiguously placed coal seams. Selection of the mining sequence for these seams, historically and currently, is based primarily on considerations of seam ownership, availability and economics. Mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. The effect is often detrimental to recovery costs and safety of mining in the subsequent seams. The purpose of this paper is to examine the conditions that can develop in an underlying seam due to stress concentrations that can occur below pillars or abutment zones in an overlying seam, and suggest guidelines for avoiding them. This situation most commonly occurs when the overlying seam is mined first, although simultaneous and subsequent mining of the upper seam can also produce such effects. Other interaction phenomena resulting from subsidence or arching will not be considered here. The methodology used in this research utilized both computer and body loaded photoelastic models to study the interaction mechanisms. Field studies are used in both interpretation and analysis of the results. Numerous examples of load transfer from upper workings exist in all parts of the world and many of these have been incorporated into this work. Such interaction problems are quite common and likely to be an ever increasing occurrence as mining activities in old seams are completed and new seams opened up.

Jan 1, 1982