Search Documents

By K. L. Whitehead, R. A. Jankowski, N. I. Jayaraman

Most continuous miner sections utilizing flooded-bed scrubbers also use blowing face ventilation. Blowing ventilation, however, interferes with dust capture and minimizes scrubber effectiveness. To enhance the efficiency of the scrubber system and reduce dust concentrations, the Bureau of Mines tested various combinations of operating parameters. Experiments for system efficiency took place in a full- scale model mine at 3.05 m roof height. In general, higher values for scrubber and face airflows resulted in lower dust concentrations. In addition, optimum dust controls would include a face ventilation to scrubber airflow ratio of one. When the airflow ratio was either less than or greater than one, the dust levels in the return and at the operator locations increased. No single dust control technique was the most effective one at all locations due to mutual interaction among techniques.

Jan 1, 1992

By Roland Hoet, Jim Patilla, Nick Madison

Increasing conveyor capacity and reliability is a common goal for many underground mines. This task is especially challenging when you must work with existing structure, belt, etc. Meeting this challenge, The Pittsburgh & Midway Coal Mining Co. North River Mine switched from constant fill to actively controlled fluid couplings, realizing a capacity increase from 2,100 tons per hour (2,300 stph) to 2,550 tons per hour (2,800 stph), with improved reliability. This paper will present a case study of The Pittsburgh & Midway Coal Mining Co.'s North River Mine underground conveyor haulage system. These conveyors included the main line conveyors as well as a tension controlled tripper booster panel conveyor. Characteristics and performance of the coupling and control system will be illustrated, demonstrating the systems controllability, simplicity, and dependability.

Jan 1, 2002

By David J. Kruse

Although it may be perfectly acceptable to neglect the belt's elastic behavior for many conveyor designs, this can lead to disastrous consequences for others. So how can a designer know in advance if a dynamic analysis is required? Unfortunately, in many cases it is impossible to foresee or predict dynamic problems prior to performing the actual analysis. However, a basic understanding of the principles of conveyor dynamics, as well as knowledge regarding common problem areas, can significantly help the designer make more educated decisions during the initial design stage. This paper will demonstrate how static calculations alone can incorrectly represent the true behavior of the conveyor system. It will also discuss the importance of correctly sizing and locating the take-up system to provide the most economical conveyor design. The use of capstans will also be discussed followed by two examples demonstrating their proper operation.

Jan 1, 2002

Exploration for SX-EW copper deposits and plant operation depend largely on the copper and gangue mineralogy inasmuch as? they govern the feasibility of leaching. Mineralogical parameters are pivotal in identifying if an ore is suitable to dump, heap, thin layer, vat or agitated leaching and/or if the ore requires curing, bioleaching or alternate lixiviants. Problems in metallurgical testing, production leaching and recovery forecasting are very often related to lack of mineralogical data. This presentation will illustrate the use of quantitative mineralogical analysis for exploration, acquisition assessment and optimization of copper leach operations.

Jan 1, 1996

By Tim Haldane

Cyanide consumption at the Gold Fields Operating Company Mesquite Mine has shown a steady decline since the heap leach operation started up in 1986. A series of solution strength changes and equipment design improvements have resulted in a reduction of sodium cyanide consumption from peak levels above 1.0 pounds NaCN per ton of ore in 1986 to current levels at 0.15 - 0.20 pounds NaCN per ton of ore. Aside from the obvious cost benefits associated with this reagent consumption reduction, the property has also enjoyed environmental benefits which go hand-in-hand with these cost savings.

Jan 1, 1990

By Robert A. Jankowski, John J. McClelland, Charles Babbitt

The purpose of this study was to develop guidelines to enable mine operators to maximize longwall dust reductions, while optimizing the use of ventilating air and shearer water consumption. A recent investigation by Foster-Miller Incorporated, under a Bureau of Mines contract, quantified the effect of increased face airflow and shearer water supply on face dust concentrations. A 70 pct reduction in respirable dust levels was achieved at the shearer operator's position during tail-to-head cutting by an incremental increase in average face air velocity from 83.8 m/min (275 fpm) to 123.4 m/min (405 fpm), while holding shearer water consumption constant. A 60 pct reduction was achieved through an increase in shearer water pressure and flow from 9.1 kg/cm2 (130 psi) at 0.19 m3/min (50 gpm) to 19.7 kg/cm2 (280 psi) at 0.28 m3/min (75 gpm), holding airflow constant. The combined effects of increasing both parameters produced an 85 pct reduction. Optimal usage of ventilating air and shearer water consumption can be achieved by defining a "point of diminishing returns" above which further increases no longer reduce dust concentrations, proportionately .

Jan 1, 1987

By C. Cardoso, G. Bermudez, A. Jalili

Bigger flotation cells can result in larger froth surface areas and longer froth transport distances, this has been credited to impact froth recovery. Thanks to recent advancements, the newer flotation machines can be designed with different launder and crowder arrangements to enhance froth management. Nevertheless, lower head grades, complex ores and even larger mechanical flotation cells can lead to insufficient froth collection, even if the cell is equipped with the most recent flotation advancements like the center launder design. Aforementioned issue can become critical at the end of the flotation row. Increased crowding has been proven to be a solution to overcome inadequate froth recovery. However, scaling-up crowders for larger flotation cells can rise challenges, particularly in terms of structural limits and design for service. This paper presents the development journey for the Spider Crowder Upgrade, an advancement to improve froth collection in large flotation cells that are already equipped with center launders.

Feb 1, 2024

By Kadri Dagdelen

The classification of selective mining units (SMU) and the assignment of grades to those classified SMU are very important in open pit mining, especially for precious metal mining. When the classification is done, the true values of the SMU grades are unknown. These unknown SMU grades are mostly estimated analyzing the geologic data and blast hole assays. To classify the SMU's based on the estimate of SMU grade, without considering uncertainty associated with unknown SMU grade, yields incorrect decision in sending material to appropriate destination. In this paper, a method is developed to classify SMU's considering the uncertainty associated with unknown SMU grades. By using this method, traditional estimate of SMU grade is replaced with conditional probability distribution of SMU grade. The decisions about the destination of a given SMU are performed by minimizing the loss due to misclassification. Also, the asymmetric loss function by penalizing the overestimation and the underestimation unequally is used in assigning grades to classified SMU's. A case study is carried out to apply the traditional ore control techniques and proposed method in classification of SMU's and the assignment of the grades in a hypothetical gold mine.

Jan 1, 1999

By T. P. Meloy

Improvement of grade and recovery requires the use of optimum processing circuits. Critical to an optimum circuit is the set point for separation. With the introduction of the concept of circuit analysis (Meloy, 1982), it became possible to determine optimum circuits for a given task. No analysis, however, has yet been made as to the grade requirements of the larger circuits. Williams and Meloy (1982), reviewed the literature and concluded that, within the operating range, most unit operations involved in particle separation behave linearly. For the purposes of this analysis, linearity will be assumed. Grade, G, is defined as the weight of the coal mineral, C, that appears in the product, divided by the weight of the coal mineral plus the weight of the gangue mineral or waste mineral, Q, which appear in the product.

Jan 1, 1982

By Claude Bazin, Robert Grant, Mike Cooper

An analysis of the Pb recovery as a function of particle size was carried out for the CuPb rougher bank of a complex sulphide mineral processing plant. Results indicate that higher recovery may be achieved by optimizing the flotation feed size distribution. Simulation of the actual grinding circuit has provided guidelines to modify circuit operating conditions in order to improve product size distribution. Plant tests ar

Jan 1, 1991

By Robert J. Brison

The intent of this paper is to try to answer the complex question: "How much grinding capacity should be designed into a new mining - milling project?" Much work has been devoted to the technical aspects of grinding, the "how" of grinding. But, in the writers' opinion, the economically important subject of optimizing grinding capacity in mill design has not received the attention it deserves, at least not in published literature. For the purpose of this paper it is necessary to distinguish clearly between optimizing operation and optimizing design. Optimizing operation involves making the best use of the available plant and equipment. Much excellent work has been done and is being done in this area. In operation, one can make tradeoffs of production rate and recovery, or recovery and grade, to maximize profits. However, this must be done within the limitations imposed in the design stage. Flexibility is limited by the existing plant. In project design, on the other hand., there are no preexisting physical limitations except as imposed by nature itself; the planners and designers have considerable latitude in their efforts to optimize the overall project. They have complete control over a large number of important design variables from the mine to the finished product. The grinding process design is one of these variables. It not only determines the capital cost charges for grinding and the maximum grinding capacity that operating management will have to work with, but also determines the range of capability of the auxiliary equipment, which fixes the degree of flexibility possible in operation. This paper is concerned with optimizing design rather than operation. The terms "optimum" and "optimize" are sometimes used in a technical sense in connection with grinding, recovery or grade. In this paper, these terms are used only in the economic sense. In this age of working large deposits of ever lower grade ores, it is in¬creasingly essential to design projects and plants for optimum economics, based on the most applicable economic. criteria. Since grinding represents a large part of both capital and operating cost of the project, and largely determines percentage recovery of metal, it should be included as one of the factors in optimizing the project design. This paper is written primarily with reference to medium to large copper concentrators employing conventional wet grinding. However, the principles involved should be applicable to other ores and other methods of grinding.

Jan 1, 1972

By W. J. Pennstrom, J. R. Arnold

This paper focuses on solution-balance management around heap-leach operations. Experience has shown that increased leach recoveries can be achieved by utilizing various leach-solution recirculation techniques. The most prominent solution-recirculation technique is intermediate leaching. The net effect of intermediate leaching is to increase recovery plant performance by increasing solution concentration tenors, to increase metal recovery by increasing the total leach time and to decrease the overall capital expenditures required for metal-recovery facilities. The adverse effect on the flow of cash from increased metal inventories in the recirculating solutions is offset by increased metal recovery and lower operating costs per unit produced.

Jan 1, 2000

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By G. Duncan

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above..

Jan 1, 1999

By R. K. Singhal

Optimization of a load-haul system for a surface mine involves two processes. The first is proper selection of mining equipment compatible with the minesite job specifications and the second is an efficient utilization of this equipment. All things being equal optimal productivity and cost is achieved when the capacity of the hauling equipment is matched at all times with that of the loading equipment.

Jan 1, 1986

By George Aul, Richard Ray

Short-hole horizontal degasification systems have been utilized in Island Creek's Virginia Division mines since 1986. These systems remove methane from the coal seam in advance of longwall mining. Without an in-seam methane drainage program, methane liberation rates from the longwall faces may exceed 0.47 cu m/s (1,000 cfrn), requiring 47 cu m/s (100,000 cfm) of air for adequate dilution capability. Optimization of the degas systems has enabled methane liberation levels and the associated ventilation requirements on the longwall faces to be reduced by 50 to 80 percent. Since the inception of the first degas system at the Virginia Pocahontas No. 6 Mine, Island Creek has developed an overall methane drainage program designed to maximize gas production and minimize ventilation requirements for methane dilution. Gas production from the degas systems is affected by four main design criteria: (1) hole location, (2) hole length and spacing, (3) collection system capacity, and (4) time available for drainage. Drilling equipment and materials for the gas collection system are selected to meet the necessary criteria while minimizing manpower requirements. Benefits gained from reducing methane liberation rates from the longwall faces are fourfold: (1) improved safety due to lower methane concentrations in the face area, (2) fewer production delays caused by excessive methane concentrations, (3) lower fan operating costs resulting from reduced air requirements, and (4) enhanced worker comfort resulting from lower air velocities and less dust generation.

Jan 1, 1991

By Charles A. Horne

Grinding mill circuits used for particle size reduction of mineral ores commonly use cyclones as primary classifiers. Typically, several individual cyclones are installed in a cluster (Fig. 1) where they can easily be added or valved-out of operation in order to balance classifier capacity with fluctuations in tonnage and recirculating loads as ore grades and hardness vary.

Jan 1, 1993

By Karl Gugel, Dante Garcia, Peter Czel, Eduardo Nunez, Joshua Morales, Boris Sullcahuaman

Real-time operational excellence is achieved through the seamless integration of various components. Key aspects include precise instrumentation, real-time data collection, data analytics, and an efficient optimization platform. Additionally, to ensure success, the real-time optimization platform must be incorporated into the site’s internal process control system (Nunez, 2022). This paper provides an overview of practical lessons and best practices for autogenous (AG), semi-autogenous (SAG), and ball mill (BM) grinding. It highlights the implementation of advanced instrumentation, specifically vibration sensors on the rotating mill shell. The paper also delves into the application of advanced analytics necessary for generating new measurements that accurately represent real-time grinding activity in the mill. These Advanced Analytics Measurements (AAM) are compared with well-known grinding curves to determine the optimal grinding point. The discussion focuses on key industry opportunities using real-time mill shell vibration results to derive new correlations and optimize the grinding process.

Feb 1, 2025

By Robert C. White, Kurt W. Keskimaki

The Henderson Mine is a large underground panel cave molybdenum mine located near Empire, Colorado. Diesel equipment is employed for all development work, as well as production ore handling. Due to fluctuating demand for molybdenum, production rates have varied from 16,000 to 32,000 metric tons per day (18,000 to 36,000 short tons per day) over the last four years. In order to obtain the maximum air flow for minimum power cost the Henderson mine has completed the following modifications to the ventilation system: removal of large intake fans, elimination of underground booster fans, shutdown of tunnel exhaust fans, completion of the number 5 exhaust ventilation shaft, and use of partially debladed main exhaust fans. These changes have reduced the annual cost of mine ventilation at the Henderson Mine by over 80 per cent, a very critical cost savings in today's competitive molybdenum marketplace.

Jan 1, 1989

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015