Search Documents

By H. S. Rathor

NTPC (National Thermal Power Corporation), a multi-unit organization, is generating 26% of India’s total power. This power is produced from its 14 coal based stations and 7 gas based stations. NTPC is entering into the business of power-distribution, power-trading, setting up of coal mines and diversification in non-conventional energy sector as well. For achieving the goal of the country “Power for All” NTPC has taken a giant stride by entering into Hydro Power generation which is also the cheapest and the cleanest renewable source of energy. In its pursuit for excellence, 800 MW Koldam Hydro Power Project is NTPC’s first venture in hydro sector. In Koldam, hydropower potential will be harnessed by constructing a 163m high earth and rock fill dam in a narrow gorge at upstream end of Bhakra reservoir. The river diversion is envisaged through two parallel, 14m finished diameter ‘horseshoe’ tunnels of length 901m and 934m at village Kian on the right bank, where the river forms a 180° loop. The diversion tunnels are designed to accommodate a flood of 6500m3/sec, taking into account the maximum probable discharge of 200 years return period. The tunnels pass through dolomite and limestone rock formations. The excavation of tunnels was done with drill and blast method. The excavation was attempted from both inlet and outlet faces. During geological investigation a rock fault was located at the outlet area. The location of the fault was such that it was passing through the edge of the Tunnel-1portal and around 30m away from the face of the Tunnel-2 portal. The quality of the rock at Inlet was also poor. To save the portals from slips, excavation of the tunnels was planned to start after the completion of the open excavation and its support system both at inlet and outlet. The tunnel excavation at inlet was envisaged by approaching the tunnels’ portal by constructing a road through 540EL bench and meeting the inlet portals on the upstream end, which would have been ready by mid2003, only after completion of the open excavation and its support system. To save time and cost, it was felt necessary to modify the planning by starting the tunnel excavation simultaneously along with open works both at inlet and outlet. The excavation at the inlet face of the tunnels started in December 2002 after rerouting the approach road to inlet portals through haulage road on the downstream and similarly Tunnel-1 at the outlet was started in the low cover area before completion of open area works. Thus the tunnel—heading excavation was started nearly 06 months early with the change of methodology.

Jan 1, 2005

By J. Changsheng, Z. Youdi

Based on the criteria of maximum net present value per ton of reserves and on the optimum matching of some other essential parameters, a comprehensive optimization model of surface-mine production rate is developed using system- engineering approaches and using the theory of economy of scale. A mine is then selected to demonstrate the application of the model.

Jan 1, 2000

By Sizhe Tan

An open pit mining operation can be considered as a production system with at least two products: ore and overburden (waste). A primary mine planning task is to schedule the production of ore and waste over its life span subject to several technical and economic constraints to maximize some objective such as the overall profit from the operation. Two major constraints are (i) the feasible combinations of ore and waste productions and (ii) the limiting function for ore production as a function of mine life. The task in scheduling production and stripping ratio (ratio of waste to ore production) is to find an ore production curve below the upper bound function of ore production, and a stripping ratio curve within the feasible domain of ore production and overburden removal while maximizing the defined objective. Zn this paper, feasibility of developing computerized optimization models to perform such a scheduling process is explored. Two optimization models are proposed for the task. In the first approach, a linear programming (LP) model is employed and in the second, a dynamic programming procedure (DP) is outlined. In these models, in addition to the consideration of the two major constraints mentioned earlier, various other contributing factors such as interest rate, equipment purchase cost and installation schedule, operating cost, and equipment idle cost are incorporated. An example is provided to illustrate the LP model application.

Jan 1, 1992

By R. K. Mehta, K. N. Han, P. B. Queneau, V. Dieudonne

A study based on a statistically designed sets of experiments (central composite design) was conducted to determine the optimum conditions for leaching a subbituminous coal (7.0 % ash) from the middle Wyodak seam in mild sulfuric acid solutions. The statistical analysis was conducted with the ash content and ash removal as the dependent variables and with the coal loading, acid concentration, ferric ion concentration, and temperature as the independent variables. Treatment of the experimental data via a simple genetic algorithm (GA) revealed that acid concentration and temperature are the two most critical variables. Unlike the case with bituminous coal, the ferric ions addition shows no beneficial effect. The optimum "macro response" predicted by GA was verified experimentally; the ash content was reduced to 2.7%, which is close to the value predicted by GA. The ash content was further reduced to 1.7% in a two-stage leaching process devised by incorporating the optimization results with that of leaching kinetic studies.

Jan 1, 1993

By Charles L. Karr

Grinding is a necessary component in the processing of a number of minerals, and improvements in this area could provide substantial cost savings for the minerals industry. Optimizing the process of grinding, however, is a difficult task because there are multiple objectives; i.e., several aspects of the process are important including the fineness of the ground product, the energy consumed in the process, and the viscosity characteristics of the final slurry. Genetic algorithms (GAs) are search algorithms based on the mechanics of natural genetics and have been proven capable of solving multiple objective optimization problems. These robust search techniques are able to rapidly locate near-optimum solutions across a broad spectrum of very difficult optimization problems. In this paper, two varieties of GA are used to optimize a grinding process as it is described by a computer model: (1) a simple genetic algorithm (SGA) and (2) a micro genetic algorithm (MGA). The performance of these techniques is compared to the performance of a more conventional search technique, a simplex algorithm. Results indicate that the GAs are efficient, versatile, quite capable of improving the grinding process, and easily incorporated into the toolbox of today's process engineer.

Jan 1, 1993

By Ronald J. Roman

A mathematical model was developed for the grinding and flotation section of Union Carbide's Bishop mill and this model was used to indicate how variations in grind, retention time, and calcite and fluorite content effects the mill capacity, tungsten units produced, and the grade and recovery of the scheelite concentrate. A model such as this is a starting point in determining the economic optimum running condition for a mining and milling operation and an example of this is given.

Jan 1, 1969

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

By A. Ghalambor

The objective of this investigation was to determine the sensitivity of three selected input parameters in the operational control of continuous bottom-fed thickeners used for the treatment of coal refuse slurries. The three variable parameters were "Feed Flow Rate," "Feed pH," and "Feed Solids Concentration." These three input parameters were studied under three polymeric conditions which were cationic polymer, anionic polymer, and a combination of cationic-anionic polymer. For each polymeric condition, two mathematical models were developed: one for overflow response, the other for underflow response. The combination polymers produced the best desired quality of overflow and underflow. For this polymeric condition, changes in the feed solids concentration was the most sensitive factor in the maintenance of the overflow quality, and the feed pH was the most sensitive factor for the maintenance of the underflow quality. The mathematical models generated a set of plots which would allow an operator to control and/or adjust any of the three variables to achieve optimum conditions.

Jan 1, 1989

By V. Ramirez, M. Mankosa, G. Luttrell, E. Wasmund

"The performance of column flotation is strongly influenced by the effectiveness of the gas sparging system. Unfortunately, field studies suggest that gas injector systems used for column sparging are not always optimized. This unfavorable condition can create a number of issues within the concentrator including lower recoveries, poorer metallurgical upgrading, decreased capacities, increased circulating loads, higher reagent consumption and inefficient energy usage. To help overcome these problems, techniques have been developed that can be adopted by plant operators to improve sparger performance. These techniques include (i) design modifications to sparger components such as nozzles, distributors and internal parts and (ii) operational improvements such as proper balancing of gas/water flows, elimination of unnecessary pressure drops, and staged injection of frothing agents. This article reviews the important criteria that govern sparger operation and provides data showing how simple low-cost improvements can positively impact column performance. INTRODUCTION Column flotation cells have become the most popular machine design for industrial applications that require high purity concentrates. The superior metallurgical performance of column cells can be largely attributed to their unique geometry, which readily accommodates the use of froth washing systems. The wash water minimizes the nonselective entrainment of ultrafine gangue minerals that would otherwise be hydraulically carried in the water reporting to the froth concentrate. The larger height-to-diameter ratio of columns allows a deep froth to be maintained, which is essential to achieve even water distribution. Due to these unique features, column cells can provide impressive levels of metallurgical performance closely approaching the ultimate separation curve predicted using the flotation release analysis method (Kohmuench et al., 2007). Another very important feature of column cells is the design of the gas sparging system. One popular choice in the minerals processing industry is the Eriez SlamJet® sparger. As shown in Figure 1, this type of sparger operates by passing compressed gas through a small discharge nozzle. Fluid turbulence created by the exiting gas disperses and distributes small bubbles into the flotation pulp. The sparger is equipped with an internal moveable rod that is attached to a pressure diaphragm in the back housing of the sparger. The internal rod automatically moves back/forward and opens/closes the nozzle outlet when the compressed gas is switched on/off. This patented design effectively eliminates the accidental backflow of flotation pulp into the injection tube during shutdowns. The sparger can be operated as a gas-only injector or with the introduction of a small amount of high-pressure sparger water (Kohmuench et al., 2010)."

Jan 1, 2016

By Lixue Wen, Jun Xiao, Dongping Shi, Yan Xue, Jinmiao Wang

Mine ventilation energy consumption is one of the main sources of energy consumption in mining production, accounting for about one-third to one-half of the total energy consumption. Therefore, reducing the energy consumption of the mine ventilation system is crucial for mining production. With the premise of meeting the airflow requirements of the underground work areas and achieving sustainable development of mining production, this paper establishes a nonlinear optimization mathematical model for the mine ventilation network with the objective of minimizing the total power. Regarding the model, optimization of the decision variables was carried out using the method of minimum spanning tree. The constraints for air flow balance, wind pressure balance, and fan operating conditions were optimized using the exterior penalty function method, thereby transforming the model into a nonlinear unconstrained model. Based on this model, a modified sooty tern optimization algorithm (mSTOA) was proposed to achieve optimization. Improved the sooty tern optimization algorithm (STOA) by using the uniform reverse strategy, fitness value-distance balance selection strategy, and mutation strategy. The STOA, mSTOA, and three other classical optimization algorithms were applied to the optimization of a ventilation system of an actual mine. The experimental results show that after using mSTOA to optimize the ventilation network airflow distribution in the mine, the total energy consumption can be reduced by about 35.06% while meeting the constraints and demands of the ventilation network regulation and usage. This is of great value to mine roadway operation environment safety and clean production.

Dec 20, 2023

By M. E. Volin

Reagent control for optimum concentrate yield was studied by laboratory batch flotation tests simulating the Groveland plant flotation circuit in which a rougher concentrate is cleaned twice. The reagents were a fatty acid collector, a sulphonate collector and sulphuric acid. The study included two types of flotation feed representative of the reground and deslimed tailing from the spiral concentration circuit, one when the ore mineral is predominantly specularite and the other when it is magnetite. The factorial design included three levels of fatty acid, five levels of sulphonate and five levels of H2S04, with the two types of ore in nested blocks, making up a total of 75 tests. Similarity of results and reproducibility were established in preliminary tests. The final tests were performed in random order under closely controlled conditions following the established procedure.

Jan 1, 1965

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is the most popular and practiced mining method in underground hard rock mines. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason is the unavailability of free faces as compared to opencast bench blasting. The geological and geotechnical parameters change gradually even within the stope itself. So, the blast design parameters should be planned according to the scenario of the upcoming ring. The blast design parameters like burden, toe spacing, inclination of blastholes, diameter of blastholes, charge density of explosive, etc., play an immense role in the rock damage. For the proper breakage of rock, the movement of burden is the prime objective. To study this, an explicit dynamic based modeler of M/s Ansys was used. The burden values were varied from 20 to 65 times of blasthole diameter to assess the optimum burden value during the study. The models were simulated for the rock having uniaxial compressive strength as 35 MPa and 102 mm blasthole diameter. Three holes were simulated having depth around 14–14.5 m. Different blast design parameters and respective blast-induced ground vibration have also been measured at the experimental site. The core samples of the rock present at the experimental site have been used for the evaluation of geotechnical parameters. These geotechnical parameters were used in the simulation models. The volume of rock excavated along the free face has been calculated in each model by varying the burden. It has been found that the burden value can varies from 35 to 40 times blasthole diameter (3.6–4.1 m) to achieve a greater volume of rock along the free face for 102 mm blasthole diameter and rock of 35 MPa uniaxial compressive strength.

Dec 22, 2023

By Dan Nilsson

The Luossavaara "Research Mine" is the First large, offensive effort in mining research conducted by the Swedish state. Over a 5-year period, 1981-1985, the Swedish Mining Research Foundation works in the "Research Mine" on the development of mining systems and equipment. The purpose is to bolster the competitive strength of the Swedish mining and mining equipment industry. The previosly abandoned Luossavaara mine in Kiruna, in northern Sweden, has been reopened especially For the project. Ore is mined and sold during the course of the research project. The income from the sales covers a large portion of the costs for teh research.

Jan 1, 1985

By Xianyang Qiu, Xiuzhi Shi, Chen Xie, Xiaofeng Huo, Yanhai Wang

In upwards medium-deep hole cut blasting, many confinement effects exist due to the small number of free surfaces, which is mainly provided by an empty hole. If the cut blasting effect cannot meet expectations, then subsequent blasting construction will be seriously affected, and large security risks to operators in the stope can be induced. The number of free surfaces is directly related to the layout of the cutting borehole. Therefore, it is necessary to optimize the layout of the first round of cutting boreholes. Theoretical analysis, numerical simulations, and field tests were used to study the formation process of cut blasting and optimize the layout of the first round of cutting boreholes. Based on the blasting parameters in the field, LSDYNA software was used to establish cut blasting models with four kinds of borehole layouts in the first round. The RHT constitutive model was used to simulate the rock-breaking effect. The numerical results show that the cut blasting effect is optimal when Nos. 3, 5, 7, and 9 are charge holes and Nos. 1, 2, 4, 6, and 8 are empty holes. In addition, the greater the number of empty holes, the larger the release space and the better the cut blasting effect. The uniformity of the empty hole distribution, namely, the uniformity of the release space, also affects the cut blasting effect. The field results indicate that a good cut blasting effect can be achieved by optimizing the borehole layout.

Sep 7, 2023

By Efstratios Karampinos, John Hadjigeorgiou, Philippe Morissette

"Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting appropriate systems at the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation.Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights into the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement throughout the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is often not available at mine sites. Even when the expertise is available, it requires a major time commitment and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support.Rock reinforcement is an integral part of all ground support systems used in underground mines. Long, flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This article focuses on the optimization of the cable-bolting strategy in squeezing conditions at the LaRonde Mine in Quebec, Canada by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 4, 2018

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018

By G Luxbacher

Computer simulation of mine ventilation systems is rapidly becoming an essential tool in mine planning and design. This paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve mainly for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria, could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1977

By M. Jawed

Coking coal reserves in India are distributed geographically in Giridih, Raniganj, East Bokaro & Jharia Coalfields (J.C.F.). 97% of prime coking coal in JCF coming through underground mines is credited to Bord & Pillar mining systems inspite of the fact that it results in heavy mining losses. The cost of mining in B & P mines has been much higher due to various factors. In this paper, O.R. model has been discussed with case study for optimizing the cost of production in operational underground mines. Also, a computer algorithm has been discussed using a schematic flowchart, which provides the trend of mining-losses 'in different mining, systems with changing design parameters and finally selects, the optimum mining system for undeveloped seams based on economic appraisal criteria.

Jan 1, 1989

By Michael Fahey, Ravi M. Damodaran, Brij M. Moudgil

The flotation behavior of Florida phosphates was studied using statistical design of experiments to evaluate conditioning parameters and their effect on flotation performance. The solids loading, conditioning time and agitation speed during conditioning were identified as the important variables affecting the reagent coating onto particles. Flotation of the conditioned slurry was carried out at fixed collector dosage and flotation conditions. Phosphate recovery upon flotation was statistically modelled as a function of the conditioning variables. The results indicated that the conditioning variables had an interactive effect on the phosphate flotation performance. Statistical optimization revealed two conditioning regimes in which optimum flotation recovery was obtained. It was determined that optimal recovery can be obtained at lower conditioning energies.

Jan 1, 1995