Search Documents

By V. Matthews

"INTRODUCTION Typical grinding electrification requirements are defined by high power, constant torque and slow speed. Dual pinion mills also include a need for tight tolerances in torque between the two motors, to avoid overloading any single motor. Standard induction (asynchronous) motors have often been used but only in combination with mechanical gearboxes (reducers), required to reduce process speed to the correct level for mill pinions. The gearbox introduces added system complexity, capital cost, maintenance and energy cost due to mechanical losses. SYNCHRONOUS AND ASYNCHRONOUS MOTORS Elimination of the gearbox requires a motor designed to operate at a very low speed (rpm). Traditionally, mill motor requirements were best served by synchronous motors. The benefits of synchronous motors include- • Higher Efficiency (no conductor losses in rotor) • Very high power at low speed • Flexible Power factor (leading or lagging) • Constant speed (not load dependent) • More accurate speed control Synchronous motor cost is higher due to construction complexity, need for exciter and excitation panel, brushes, brush lifters. Figure 1 represents the equivalent circuit for a synchronous motor.Asynchronous motors, also known as squirrel cage induction motors, are singly excited, per Figure 2, the resulting equivalency circuit is less complex and only in need of a single voltage source.Commonly, a DC voltage supply is connected to the rotor (both physically and electrically) via brushes. The DC voltage enables the production of flux in a single direction. The brushes are connected to rings. The slip rings encircle the rotor but are insulated from the rotor. The slip rings are connected to a rotor winding known as a field winding. On large motors, brushless exciters are often used. A brushless exciter is a small AC generator whose field circuits are mounted on the stator and armature circuits are mounted on the rotor shaft. The exciter generator’s 3-phase output is rectified to DC by a 3-phase rectifier (mounted on the shaft) and fed into the main DC field circuit. It is possible to adjust the field current on the main machine by controlling the small DC field current of the exciter generator (located on the stator). [1] Brushless synchronous motors are often preferred over the traditional brush design but introduce additional complexity to motor construction in the form of additional windings and rectifiers comprising the excitation circuit. It stands to reason that because of the additional complexity, a synchronous motor will be higher in cost than an equally rated asynchronous induction machine."

Jan 1, 2015

By Nick A. Hasenack

A full survey of the laboratory and blast-furnace tests on 2 types of acid pellets is given. From the laboratory tests, carried out in an atmosphere containing hydrogen, it appears that type B, produced out of 100% magnetitic ores, has a far better low temperature disintegration index and a lower reducibility index than type A, produced from a hematite/magnetite mixture. The swelling index, chemical composition and mechanical properties of both types of pellets do not differ significantly. From the blast-furnace test, carried out with a burden consisting of 45% of pellets and 45% of sinter with basicsty ratio about 2.2, and at constant driving rate, it follows that there is no significant relationship between the disintegration value of the pellets and the blast-furnace permeability. If also is concluded that the lower reducibility of the type B pellets leads to a significantly higher coke consumption.

Jan 1, 1975

By Huaiyang Zhou

"Hydrothermal systems are a major component of the processes that shape the composition and structure of the ocean crust, providing a major pathway for the exchange of heat and elements between the Earth’s crust and oceans, and a locus for prolific biological activity on the seafloor and underlying crust. On the other hand, the structure and composition of hydrothermal systems are the result of complex interactions between heat sources, fluids, wall rocks, tectonic controls and even biological processes.Ultraslow spreading ridges, including the Southwest Indian Ridge and the Gakkel Ridge, are most remarkable end member in plate-boundary structures (Dick et al., 2003), featured with extensive tectonic amagmatic spreading and frequent exposure of peridotite and gabbro. With intensive surveys during the last decades, it was suggested that ultraslow ridges are several times more effective than faster-spreading ridges in sustaining hydrothermal activity. This increased longevity can be attributed to deep mining of heat and even exothermic serpentinisation (Baker et al., 2004).Distinct from faster spreading ridges, one characteristics of hydrothermal mineralization on seafloor in ultraslow spreading ridges, including the active Dragon Flag hydrothermal field at 49.6 degree on the Southwest Indian Ridge, is the abundant and pervasive distribution of lower temperature minerals (such as Fe-silica or silica, Mn (Fe) oxides, sepiolite, pyrite, marcasite, etc.) in the hydrothermal fields. Structures formed by lower temperature activity in active and dead hydrothermal fields can also be identified. High temperature minerals such as chalcopyrite are rare or very limited in hydrothermal chimneys at ultraslow spreading ridges. The distribution of diverse low temperature hydrothermal activity is consistence with the deep heating mechanisms and hydrothermal circulations in the complex framework of ultraslow spreading tectonics. On the other hand, deeper and more extensive mineralization at certain locations along the ultraslow spreading ridges can be reasonably presumed."

Sep 1, 2014

By J. Trouw, W. de Bruijn, A. van Sandwijk, R. H. Heerema

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically prepared hematite powder evenly doped with 1 % by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous theimogravimetric and dilatometric analyses were performed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process. The results indicate that the degree of expansion or shrinkage of hematite during reduction is highly dependent upon impurities associated with the original material; marked differences in reduction rate and microstructure were observed as well. An important finding is that the influence of a particular additive can also strongly vary from one reduction stage to the next. The reduction behavior appears to be affected by the physical and chemical nature of the associations formed by the added elements.

Jan 1, 1990

By W. de Bruijn

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically pre-pared hematite powder evenly doped with 1% by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous thermo-gravimetric and dilatometric analyses were per-formed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process.

Jan 1, 1988

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By F. Bourgeois, J. A. Herbst, R. P. King

The ultrafast load cell (UFLC) has proved to be an exceptionally good device for the study of the fundamental processes associated with the impact fracture of particulate material. A new high- sensitivity UFLC has been commissioned at the Utah Comminution Center for the study of low-impact energy single-particle fracture. The force-time histories of individual fracture events have been measured. The force and energy absorbed at crack initiation have been measured at several particle sizes. The mass specific energy for fracture and the associated breakage function have been determined. The distributions of particle breakage energy and particle strength have been measured as a function of particle size.

Jan 1, 1992

By Andrew J. Petruska, Austin F. Oltmanns

The paper proposes a capacitive load cell for detecting changes in material and tool wear conditions for conical picks used in underground mining. The current process is dangerous and subjective, relying on human operators near the cutting interface. The new sensor aims to improve worker safety by allowing operators to perform their functions from a greater distance.

Aug 1, 2023

By Andrew J. Petruska, Austin F. Oltmanns

This work proposes a capacitive load cell for conical picks to enable underground continuous mining machine operators to perform their roles away from known hazardous regions near the machine. The load cell is embedded in commercially available flexible printed circuit board, integrates with the target tooling, and demonstrates in situ force sensing of vibration signatures for continuous mining cutting tools. Changes in material constitution, tool mass, and tool geometry cause modal variations in vibrational response measurable with force sensors at the cutting interface. Time-series measurements are captured during rock cutting tests using a linear cutting machine. These measurements are segmented into small windows, less than 0.25 s, and are preprocessed using the fast Fourier transform, which highlights the modal variations. The transformed measurements are then classified into different material and wear categories using support-vector machines with the radial basis function kernel. Different normalization schemes and Fourier transform methods are tested for signal preprocessing. Results show that the power spectral density measurements with normally distributed coefficients give good results for material classification, while the normalized time-domain measurements give better results for wear classification. Under laboratory conditions, this technique is shown to classify material and wear categories with F1 score above 0.85 out of 1.0 for our experiment. This technology could be used to assist operators in assessing material and wear conditions from a safer distance. It has applications in the coal mining industry as well as other applications which use conical picks such as road milling.

Mar 25, 2023

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal&apos;s organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors&apos; recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal&apos;s organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors&apos; remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By Hans G. Machel

In low-temperature diagenetic environments (0 c T c 60 - 80°C), elemental sulfur forms by six common processes: via (1) inorganic oxidation of H2S by molecular oxygen, (2) inorganic oxidation of H2S by ferric iron compounds, (3) polysulfide disproportion- ation; and via the microbial metabolic actions of (4) colorless sulfur bacteria, (5) colored sulfur bacteria, and (6) some types of thiobacilli. Economically viable deposits of native sulfur usually are formed by only one process: inorganic oxidation of H2S by molecular oxygen. The amount of elemental sulfur is also limited by three common processes that destroy it in low- temperature diagenetic environments: bacterial reduction, bacterial oxidation, and inorganic oxidation. In high-temperature diagenetic environments (80 - 10o°C c T c 150 - 200°C), particularly in sour gas reservoirs, there are seven common processes forming elemental sulfur: (1) SOdH2S reaction, (2) H2S- hydrocarbon reaction, (3) polysulfide disproportionation, (4) catalytic H2S decomposition, (5) C02-H2S reaction, (6) chlorinification, and (7) exsolution of physically dissolved elemental sulfur. Natural processes that destroy or remove elemental sulfur in such settings are hydrocarbon sulfurization, polysulfide formation, and advection. In most sour gas reservoirs, relatively small quantities of elemental sulfur occur as a free phase (solid or liquid). However, elemental sulfur often precipitates in copious amounts from the reservoir fluids via exsolution and polysulfide disproportionation during production of sour gas reservoirs. By extension, elemental sulfur may precipitate from reservoir fluids in relatively large quantities upon uplift and erosion of deep sour gas reservoirs, or from advection of sulfurous fluids into shallower settings via faults or other high-permeability pathways.

Jan 1, 1992

By J. M. Duke

Significant resources grading less than about 1 % nickel occur in magmatic sulfide deposits of two types. In the Mt. Keith type, extensive zones of disseminated nickel sulfides occur in the central portions of certain synvolcanic dunite-peridotite sills of komatiitic affinity in Archean greens tone terranes. In the Duluth type, disseminated copper-nickel sulfides occur near the basal margins of intrusions of flood basaltic affinity associated with intracontinental rifting. In both types, the parent magmas became saturated with sulfide following the onset of fractional crystallization and the separation of the immiscible sulfide melt was accompanied by the precipitation of a relatively large proportion of silicates. The abundant silicate crystals impeded the coalescense and accumulation of the sulfide droplets with the resulting formation of large but low grade deposits.

Jan 1, 1982

By Alix Thierart, Yann Rouillard, Bernard Catalano

Bessac's presence in Singapore started in 2014 with the construction of the Thomson metro line, which includes 18 miles of twin-bore tunnels and 22 stations split into 17 construction packages. Bessac joint venture was allotted the T219 lot. The works include the construction of a new 660-foot (200-meter) long transfer station, two parallel 19-foot (5.8 m) ID tunnels and a pedestrian underpass. The urban context and the very soft ground stratum imposed to utilize unusual tunneling techniques, from upgrading a slurry TBM to a high-density slurry TBM to launch with very low cover and canopy pipe roofing completed with a MTBM without retrieval shaft.

Jun 23, 2024

By B. M. Davis, J. Wilkins

The method of conditional simulation is easily implemented on the personal computer when the LU decomposition algorithm of Davis (1987) is employed. This algorithm is fairly compact, yet can generate moderate-sized simulations in a few minutes on a 80286 or 80386-based personal computer. The application of conditional simulation presented here is to generate possible ore inventories from a limited amount of exploration sampling. The simulations can then he examined to decide if the potential inventories are sufficiently attractive to proceed with further exploration. An example showing one application of this approach is presented.

Jan 1, 1992

By B. M. Davis

Characterizing exploration prospect potential has aspects that differ from those encountered during ore reserve estimation. One problem is determination of the ore reserve potential prior to acquisition of significant volumes of hard data. The evaluation is subjective and data are usually sparse and of uncertain quality. However, estimations of the ore reserve potential are commonly demanded by management before project funding will be approved. The estimations from several prospects, along with the uncertainties inherent to the estimation, are then used to compare and contrast the potential of several prospects, often with widely varying geologic models.

Jan 1, 1990

By Cliff G. Paton, Sheldon B. Bland, Roger E. Melley

This paper looks at four critical lubricants used in the conveyor systems of the northern Albertan oil sand facility. The requirements for the lubricants used in the electric motors and gear boxes of the drive systems, the pulley bearing and the idler bearings are discussed in terms of the applications and the environment. A number of developments that have occurred in recent years are presented. Data from the field and from custom designed testing in the laboratory are used to support the role of simulation testing in problem solving in this area of technology.

Jan 1, 1996

By Edward M. Downs

This paper is a brief review of the lubrication requirements of enclosed gearing on earth moving equipment, particularly as they apply to intermediate and large draglines and shovels used in open pit mining operations. It discusses the requirements of spur, helical and herringbone gearing in both horizontal and vertically mounted applications. The effects of base stock, oil viscosity, additive treatment, quantity of oil and method of application are considered. In addition, a newly designed circulating oil system for enclosed swing gear cases and the reasons for its development are discussed.

Jan 1, 1968

By E. C. Wilson

The knowledge concerning the lubrication of open gearing for mining machinery has contained many unknowns and at its best has relied to a great degree on a "Rule of Thumb" procedure. It will be within the scope of this paper to explain what we have learned to date and what must be learned in the future. The results in the lubrication of open gearing have spanned the spectrum of unsatisfactory to satisfactory. With the advent of larger mining machinery, we are faced with the necessity of a more thorough knowledge of open gear lubrication. We have avail- able, better steels for the gearing, advanced technology and machinery for cutting proper tooth profiles, and better means of aligning the teeth in the gear train. This has made it possible to transmit more horsepower through the same size gear set than ever before, if we have the proper lubrication to complement the factors previously mentioned. We have set up computer programs which can calculate the data fox the tooth forms, the correct operating center distances, the contact stresses, the bending stresses, and the PVT factor of the gear teeth. This program does not, at the present, have sufficient data available to calculate the type of lubricant which should be used.

Jan 1, 1968