Search Documents

By Keith G. Wallace

The effect of face resistance on ventilation air leakage through stoppings was measured in a twin development heading. Face resistance was varied by alternately tightening or loosening the face line brattice to change the line brattice leakage. Results indicated that tight brattice lines are necessary to maintain acceptable airflow at the face but result in higher leakage throughout the entire system, reduced overall ventilation efficiency, and higher operating costs. Conversely, a low face resistance which simulated an auxiliary fan/duct system gave reduced stopping leakage losses, higher quantities of air at the last open cross-cut and greater entire system efficiencies

Jan 1, 1984

By H. Bradley Johnson

A number of Federal laws affecting safety and health in the mining industry has been enacted and revised over a period of many years. We have tended to classify these laws and their applicability into three categories: 1) coal mines, 2) metal and nonmetallic mines, and 3) mines with Federal supply contracts. With the growing attention which is being given to mine safety by the Federal government, the entire mining industry should keep aware of all developments in the administration of each of these laws.

Jan 1, 1970

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990

By M. Misra

The processing strategy for the effective separation of bitumen from low grade (< 10 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1979

By Donald P. Spitzer, Peter V. Avotins

The flow properties of thickener underflow slurries can be characterized by their rheological parameters. Most of these slurries exhibit Bingham plastic behavior, characterized by a yield stress, to, and a Bingham viscosity, nB. Red mud is generated as a leach residue in the Bayer process. The use of new Bayer process flocculants which contain hydroxamate functional groups leads to muds which are qua1itatively considerably more fluid than muds generated with conventional polyacrylates or acrylatefamide copolymers. A variety of rheological tests confirm lower yield stresses and less extended floc structures with the new flocculants, at the same solids levels. Conversely, under given viscosity restraints, the new polymers make it possible to operate at higher solids levels, which offers major benefits in processing red muds.

Jan 1, 1992

By R. P. Benson, D. H. MacDonald, D. R. McCreath

1 - INTRODUCTION The Canadian Shield is well known as being among the older exposed areas of the earth&apos;s surface. Except for local zones, its extent from the Arctic to central North America is characterized by strong and durable crystalline rocks. It is generally regarded as highly competent for tunnelling and underground excavation and, as a result, many openings are excavated in it with minimal temporary support. If hydraulic efficiency is not a factor, tunnels do not usually require continuous concrete linings. A high percentage of the crystalline rocks of the Shield are of metamorphic origin and as such one of the dominant characteristics is their foliation. Zones of sheared or faulted rock are common in the Canadian Shield, particularly in association with foliation. These zones may be created during the late stages of the metamorphic process, leaving shear zones as an integral feature of foliated rock. As foliation is a preferred direction of weakness, deformation and rupture during subsequent tectonism may also create parallel shear zones. These "foliation shear zones", as described by Deere (1973), are an adverse feature of the otherwise durable rocks of the Canadian Shield. The zones may range from faults of major proportions to seams only a fraction of an inch thick. If fault gouge or alteration products exist in the zone the strength of the rock mass may be great1y reduced. As foliation is usually continuous, large unstable wedges of rock may be created if the opening is subparallel to the foliation. The effect on the construction of underground openings in terms of excavations, support and scheduling can be significant.

Jan 1, 1974

By F. G. Miller

To improve coal flotation Bethlehem Steel Corporation&apos;s Research Department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies5 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the bas is for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14M x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level.

Jan 1, 1968

By J-P Franzidis

A study was undertaken to determine the effect of five industrial frothers on the relationship between entrainment recovery and water recovery. The experiments were conducted using a Batequip rectangular 60 liter steel cell which was run in parallel with the first cell in a copper/silver prefloat rougher circuit. The concentration of the frothers ranged from 2.5 g/ton to 8.4 g/ton. The experiments were repeated at three different froth depths. A power function was found to fit this relationship with no discontinuity in the relationship caused by the changes in frother type and concentration and froth depth.

Jan 1, 2000

By Qun Wang, Elena A. Alonso, Janusz S. Laskowski

Primary normal long-chain amines are insoluble in saturated brine. Their colloidal solubility (dispersion) in concentrated electrolyte solutions is strongly affected by the presence of surfactants (frothers). This paper shows that a better usage of alcohol type surfactants, which are commonly used in potash ore flotation as frothers, can significantly improve the flotation of both coarse and fine sylvite particles. A new process of potash ore flotation is developed, which includes premixing an effective frother with an aqueous solution of amine or emulsion of extender oil containing amine. With such a combination of flotation reagents, KC1 particles up to 5 mm in size float very well in the short flotation column, and particles up to 2 mm float in a mechanical cell; when used to treat fine fraction-containing sample, this method may as well provide an improved concentrate grade.

Jan 1, 1995

By V. N. Kelly

The ability to link geological sections on a graphics screen to form three dimensional geology representation was implemented at Kidd Creek in 1987. This technique affords an opportunity to optimize metal estimation in ore at the Kidd Creek copper, zinc and silver mine, by applying enhanced interpretation methods. On a series of geological sections varieties of ore are outlined. These are linked from section to section to form polyhedra which closely simulate the three dimensional shapes of the different ore types referred to as mintypes. The orebodies are divided into zones, referred to as domains, that approximate the function of variograrns, for which&apos; preferential continuity of mineralization has been estimated for distances in the width, strike and dip directions. These distances define ellipsoidal volumes of influence. The domains are also linked into polyhedra. Both types, coded by ore variety and zone, are mapped into the block model. Tonnage and metal values are calculated for ten-foot cubical cells of the block model by any of several estimation methods under domain control. In estimating the metal grades for a cell the predetermined search ellipse is applied to select only those drill hole assays of the same mintype as the cell designation. Once grade estimations have been determined for the cubical cells comprising the model, a wide range of stored information can be viewed. For example, in plan at any row elevation or on vertical section at any azimuth, as either printed values for the cells or as contoured data. This flexibility is of particular value in checking and refining the geological interpretation to better conform to ore types and grades actually mined. Combined with three dimensional geological modelling, and correctly chosen domains, the use of mintypes implants essential geological control into the system and prevents assays for one ore type from affecting grade estimation in adjacent ore types. The three dimensional geological modelling and block model segments provide information which is effectively applied to the stope design, production, planning and control parts of the system.

Jan 1, 1989

By L. A. Baker

The presence of goethite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18 inch deep bed of green balls the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1972

By Mary E. Learmont

Grinding with steel media adversely affects the flotation response of galena. Electrochemical measurements, flotation tests, and AES, XPS, and STEM examinations were employed to identify interactions between galena and mild steel. Iron oxide, hydroxide, or sulfate species that formed on the galena surface upon contact with mild steel decreased its floatability, with the time of contact and aeration condition affecting the severity of the flotation depression.. Parallel tests performed with an active metal, magnesium, indicated that floatability was also affected by the presence of a surface coating involving lead species.

Jan 1, 1984

By R. W. Bruce

The normal practice for processing complex sulphide ore has been to grind with steel balls and/or rods in steel mills before flotation. Little thought had been given to the effect of grinding media on flotation selectivity of copper-lead -zinc ore until 1960 when Rey and Formanek(1) published their experiments on sphalerite floatability after grinding in a porcelain mill with ceramic pebbles. The studies by Rey and Formanek had a pronounced effect on the milling of copper-lead-zinc ores in Canada and possibly throughout the world at a time when autogenous grinding was creating a great deal of interest. The impression was created, and possibly still exists with some mill men, that grinding an ore in the absence of steel will result in a loss of selectivity between copper, lead and zinc minerals. This is in spite of the fact Rey and Formanek&apos;s experiments showed that the "naturall floatability" of sphalerite was not apparent after grinding in a porcelain pebble mill in an alkaline pulp.

Jan 1, 1976

By H. Evans

It is well known that iron-ore pellets are considered one of the best blast-furnace burden materials used today. The demand for pellets is demonstrated by the increase in pellet output from one million tons in 1955 to approximately 37 million tons in 1964. This growth continues as new plants are placed on-stream each year. The consumer generally specified (1) the acceptable content and range of chemical constituents, (2) a minimum strength determined by some standard testing procedure, (3) the size range of pellets, and (4) perhaps a measure of reducibility.

Jan 1, 1966

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By Corale L. Brierley

The effect of hydrogen peroxide (H2O2) on growth and respiration of Thiobacillus, thiooxidans, and Thiobacillus ferrooxidans, organisms involved in acid leaching of copper sulfide minerals and uranium oxides, was examined. Oxygen uptake and growth by T. thiooxidans were inhibited after contact with 0.82 mM H2O2. Inhibition of oxygen uptake by T. ferrooxidans occurred at 8.24 mM H2O2, and growth was inhibited after 6 hours exposure to 2.06 mM H2O2. Higher concentrations of H2O2 can be used without detriment to thiobacilli if it is dissipated prior to reaching the oxidation pond or dump surface. INTRODUCTION In recent years, hydrometallurgical processes for recovery of metal values from low-grade ore minerals have played an increasingly important role. Dump leaching of low-grade copper waste materials in the western United States now yields 11.5% of the total U. S. copper production. Although scavenger operations in uranium leaching have been successful, the state-of-the-art of in-situ

Jan 1, 1977

By R. Stocker

Flotation recovery of molybdenite particles finer than 15 micrones sharpy decreases with decreasing size. A totally hydrophobic latex agglomerant (UBC-1), which was previously reported to be very efficient in agglomerating hydrophobic fine coal, has been found to agglomerate fine molybdenite particles. The agglomeration takes place only in the presence of MIBC which is commonly used as a frother in molybdenite flotation. Adsorption tests confirmed that MIBC is adsorbed onto molybdenite. The effect of the agglomeration on flotation has been studied by floating fine molybdenite from mixtures with quartz using the UBC-l agglomerant and the MIBC frother. A significant improvement in the flotation of fine molybdenite has been observed in the presence of the UBC-l agglomerant. The best results have been obtained around pH 5.5 which corresponds to the iso-electric-point of molybdenite.

Jan 1, 1997

By Hassan El-Shall, M. N. Ahmad, Ponisseril Somasundaran, C. R. Holland, G. M. Walker, N. Iles, R. D. Chandler, Regis Stana, B. Duddy, Patrick Zhang

Phosphoric acid is a major raw material for the production of ammonium phosphate (AP) that is used as an intermediate in fertilizer production. Impurities within commercial grade wet process phosphoric acid are important in producing a fertilizer granule with good handling properties. The impurities identified as being important are; iron (III), aluminium and fluorine-containing compounds. Results show that the viscosity of the AP slurry produced increases by increasing the amount of impurity in the acid. Bench scale tests have been successfully replicated on a plant scale leading to a better understanding of the composition of impurity levels within phosphoric acid required to produce a high quality, free flowing, hard, spherical and non-caking granular fertilizer.

Jan 1, 2002

By T. S. Spicer

Inflammability and crossing point apparatuses were used to study the influence of increasing amounts of such inerts as ash, fly-ash, pyrite, limestone and Portland cement with several pulverized bituminous coals. The results indicate that it requires large proportions of inerts to substantially suppress the ease of ignition.

Jan 1, 1962

A large lab apparatus was designed using a scale-down methodology based on the design legacy of the current FLSmidth commercial forced air flotation machines. This new apparatus, along with a new test methodology, was used to evaluate new rapid prototype concepts. The apparatus was designed to monitor bubble size, power, pumping capacity, Jg, velocity profiles, froth character, and tip speed. The methodology developed follows a sequence that goes from hydrodynamic tests and solids suspension tests to a flotation kinetic test. This methodology has been demonstrated to be a good tool to determine the effect of machine design changes on flotation.

Jan 1, 2012