Search Documents

By M. Baumann

Operating and maintaining the heavy equipment used in open-pit mining operations is an ongoing challenge for mines. Typical operations employ a combination of shovels, wheel loaders, and haul trucks to excavate and transport the material for further processing. As this is the first point of contact for the material after blasting, it is often a bottleneck of all downstream processes, thus, equipment uptime and efficiency is crucial. Automated systems for bucket tooth monitoring, payload measurement, proximity detection, and rock fragmentation analysis will be examined. The impact of these systems on operation safety, efficiency, and reliability, in real-world scenarios will be investigated. The process of managing all the above fleet of equipment in a mine can be streamlined by connecting the equipment monitoring systems to a central server. Using the central server, the distribution of this information can be automated to ensure that the right people see the data in a timely manner, improving both proactive and reactive responses to threats to safety and productivity.

Feb 23, 2014

By C. Patrick

Annually, the US coal industry generates and must dispose of over 200 million st (180 million t) of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks with refuse blocks for use in ventilation stoppings in underground mines. Refuse, collected from three active preparation plants in eastern Kentucky, was used as the primary as aggregate in the preparation of concrete cylinder. Stress-strain analyses on the refuse cylinders yielded compressive strengths of from 59% to 77 % of the control-group strengths. Low variability within the groups was found while significant differences between the groups existed. On-going determinations of the effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1997

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By H. Akgun, J. J. K. Daemen

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. Presented in this paper are the results of push-out tests on two types of expansive cement grout plugs emplaced in rock salt. The average interface shear strengths range from 2 to 12 MPa. Peak shear stresses (assuming an elastic stress distribution along the interface) are up to eight times higher. Dissolution along the interface may be enhanced by clay inclusions in the salt and appears to reduce bond strengths. Application of the results to the design of plugs for larger openings (e.g., shafts, drifts, or boreholes) is discussed.

Jan 1, 1995

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By Syd S. Peng

Is the laboratory sized coal specimen much stronger than underground coal pillars? The answer to this question has a profound implication to many coal operators. It will decide how much of the coal reserve can be recovered. Or, in many cases, it will determine whether it can be mined economically. Recent trends in several eastern states to establish regulations regarding coal pillar design to prevent surface subsidence long after mining heighten the debates. And, in some cases, these trends highlight the existing practices that seriously question the conventional wisdom. Currently, nearly all researchers and practitioners agree that as the size of rock specimens increases, its strength decreases. This concept has been universally adopted as the basic principle for coal pillar design in the United States. Several formulas have been derived to account for this effect. The reduction factor for underground coal pillars ranges from one-half to one-sixth of the strength obtained in the laboratory, depending on the formula selected. Recent case studies indicate that the reduction factor is not justifiable, at east in some cases. The use of a reduction factor is based on the assumption hat smaller rock specimens as tested in he laboratory contain none or fewer fractures or planes of weakness than larger specimens or underground coal pillars. In other words, the larger the rock materials, the more fractures it contains and subsequently weaker in strength. Do all underground coal pillars have more fractures than laboratory sized coal specimens? Not necessarily. All coal contains cleats. Some are con¬spicuous but others are not. In terms of cleat density (number of cleats per unit area), there is no difference between an underground coal pillar and a laboratory sized specimen, provided the specimen size is larger than the cleat spacing, which is mostly 25 to 75 mm (1 to 3 in.).

Jan 1, 1993

By James I. Mathis

Should an arbitrary reduction factor be applied to laboratory compressive strengths when designing pillars? The answer is, as is the main contention of Peng's article, probably not. Many factors affect the strength of the material remaining in the pillar. On the other hand, outside influences will influence the strength testing results from the lab. This is not the first article, nor the last, to discuss the discrepancy between the two strengths. As was discussed in the article, actual pillar strength is affected by several factors. The two mentioned were: • The scale effect of discontinuities. How large must the pillar be so that the increase in discontinuity count with size will not decrease the strength. • Non-uniform strengths and lithologic units within the pillar. The scale effect of discontinuities is important. What size block must be tested so that the rock mass strength is actually measured? For a highly fractured rock mass, or coal with a high cleat density, this sample may be quite small. Conversely, if an unaltered, moderately jointed, quartz monzonite was examined, the sample block would likely be very large. This is the subject of ongo¬ing research. More to the point, if the tested sample is sufficiently large to model the rock mass strength, then no reductions should be made in the lab strength based on this factor alone. Non-uniform strengths and variations in lithologic units will also affect the pillar strength. I am not an expert in coal mines, having gained my experience in hard rock metal mining. These problems, though, are commonplace. However, strength sampling for pillar strength determination involves sampling material from within the lithologic unit that will form the pillar, not from pieces of material found on the floor. In addition, this sampling should cover the entire range of strengths of the material in the pillar-hard units (such as the partings described by Peng), as well as soft units. Testing results should then be included in the pillar design. Contrary to statements in Peng's article, at least one rock mass rating system (Laubscher, 1990) allows for the compositing of strong and weak units into a design rock mass strength that can be used for pillar design.

Jan 1, 1993

By Bernard Amadei, Michael J. Robison

The purpose of this paper is to present the results of 102 mu1tiaxial tests conducted on cubical specimens of Indiana limestone using the mu1tiaxial apparatus available at the University of Colorado at Boulder. These tests include (1) uni-axia1 compression and tension, (2) bi-axial and tri-axial compression, (3) biaxial compression- tension and (4) tri-axial compression-compression- tension. The applicabi1ity of existing failure criteria to predict the strength of the tested materia1 is discussed.

Jan 1, 1986

By Nelson Alonso Portal Ravichaua, Melissa Esther Mendoza Tirado, Raúl Arévalo Saavedra

This study analyzes the implementation of an integrated strategy for environmental education and community awareness in Cajamarca, Peru—an Andean region affected by climate variability and the public perception of miningrelated water shortages. In collaboration with the Interactive Water and Earth Museum and the Newmont ALAC Foundation, three-month campaigns were conducted in schools and local communities. Key topics included the water cycle, climate change, and water availability, linked to urban infrastructure projects that improved flow rates through strategically located tubular wells tapping underground aquifers. The initiative addressed the challenge of communication in a context where mining is often blamed for scarcity, fostering scientific understanding of contributing factors. The study highlights how science-based outreach and institutional collaboration can strengthen resilience and promote sustainable water stewardship in mining-influenced regions.

Feb 22, 2026

By Syd S. Peng

In the past few years, the numbers of underground coal mines in this country using longwa11 mining method have been dramatically increased. In the latest count there are approximately 90 10ngwa11 faces amounting roughly 8% of the total underground production. Meanwhile, shortwall mining adapting longwa11 powered supports to 'coal mining and handling systems in room and pillar mining is also gaining importance in the Appalachian coal field. Although there are only 7 operating shortwall faces so far, indications are that it will be increasing steadily. Modern longwall faces are highly mechanized and productive. One of these key elements that contribute to the success of modern longwall mining is self-advanced powered supports. There are several types of powered supports. Frame type is two sets of one to four hydraulic legs supporting beam-type roof canopy and floor base. However, chock type is more popular and connected to broad roof and base structure. Shield supports were introduced recently but proved to be highly successful (1). A shield support consists of two hydraulic jacks mounted between a base plate and a gob shield. The base plate is hinged to gob shield which is in turn hinged to roof canopy.

Jan 1, 1977

By Ching L. Wu, Joseph Penzien

An analytical procedure is presented for evaluating the stresses in linings of bored tunnels caused by kinematic soil-lining interaction. Three cases of interaction as produced by the following conditions are treated: (1) relaxation of in situ soil stresses near a lining following its installation; (2) overburden pressure at the soil surface; and (3) free-field soil response resulting from an earthquake. Non-dimensional formulas and graphs resulting from parametric studies are presented for practical tunnel design applications. The procedure is applied separately to a steel lining and a concrete lining for a site located at the lower end of Market Street in San Francisco through which a BART (Bay Area Rapid Transit)tunnel passes.

Jan 1, 1997

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By G. Bylapudi, A. Bhagwat, K. Mondal, A. J. S. (Sam) Spearing

Minimizing the effects of corrosion improves the long-term performance of the rock anchors and ground control systems in underground mines, which is fundamental for safe operation over the design period. The primary objective of this study is to explain the problems due to stress corrosion cracking (SCC), strain-induced corrosion cracking (SICC) and other forms of corrosion, and why the mining industry’s ground control professionals should take this into serious consideration. It is important to clearly determine the kind of SCC mechanisms that causes roof bolt failures in order to suggest the necessary action plan to mitigate or eliminate the possibility of the cause. Pertinent literature and studies around the globe on this complicated subject are reviewed. The secondary objective is to encourage the use of corrosion-resistant ground control products in the underground mining industry in areas of high corrosion potential. Characteristics of SCC on high strength steel are also reviewed. The literature and preliminary studies to date indicate that research work is necessary in United States.

Jan 1, 2015

By N. K. Bohidar

Evaluation of the stability of a structure under given boundary conditions requires accurate knowledge of the state of stress as well as the mechanism of failure at the critical state of stress. This paper represents a part of the research done by N. K. Bohidar during 1965-1968 for his Ph. D. research in Mining Engineering at the University of Utah. It summarizes the determination of internal stress and failure phenomena around cylindrical openings in viscoelastic media subjected to lateral restraint and vertical uniaxial load. The conditions of lateral restraint and viscoelastic nature of the media represent conditions associated with subsurface openings in rocks. The financial assistance provided to the project from the University of Utah Research (Uniform School Fund), W. C. Browning Scholarship Fund, Earth Science Research Fund, and D. C. Jackling Loan and Scholarship Fund is gratefully acknowledged. The authors also acknowledge the assistance of S. Siugh, W. Jones, and K. McCarter during the project.

Jan 1, 1970

By S. Bastola

Over 80% of roof falls in Illinois coal mines occur at intersections. Regular intersection geometries with sharp corners have been typically analyzed in literature. This study has analyzed stress distribution around typical field 4-way intersection geometry and compared it with similar data for regular four-way intersection geometry. These analyses were performed using 3-D numerical analyses for a typical lithology associated with No 6 coal seam in southern Illinois. Linear elastic and non-linear analyses, using Hoek-Brown failure criteria for different lithological units, were performed. The 3-D models incorporated bedding planes and pre-mining horizontal stresses. Effect of diagonal widths of the intersection and pre-mining horizontal stresses were examined due to their influence on stability. In addition to stress distribution, contours of safety factors, and displacement analyses were performed to assess stability of intersections.

Feb 27, 2013

By Ke Yang, Kai Zhang, Xiaolou Chi, Xiangyang Zhang, Yingming Li

Based on the research background of 1303 working face return air roadway in Jinyuan Zhaoxian Mine, Shaanxi Province, a method of determining the reasonable spacing of boreholes is proposed based on the stress transfer degree of coal above and between boreholes, combined with the law of plastic zone and energy evolution by theoretical analysis and numerical simulation. After drilling pressure relief, the average daily energy of microseismic events decreased by 70%, and those with microseismic energy greater than 104 J decreased by 99.2%. The research has a strong guiding significance and research value for determining the reasonable distance of borehole pressure relief.

Jun 25, 2024

By Zachary E. Wedding, Zach Agioutantis

Excavation of underground openings results in the redistribution of the in situ stress into the rock adjacent to the opening. Stress redistribution depends on opening geometry, pillar geometry, material properties, possible confinement, and constitutive models describing the behavior of adjacent rock. This paper presents typical pillar stress distributions for elastic and yielding pillars as a function of opening geometry, material properties, and material constitutive models and highlights the differences between them. Stress distributions are compared with empirical strength profiles that have been developed for coal pillars as well as actual pillar geometries documented for stone pillars.

Jul 1, 2023

By Robert Stefanko

Longwall mining appears very attractive from an engineering standpoint because of its simplicity. The use of one long, continuous face can simplify power distribution, ventilation, and supervision, and minimizes or prevents lost time associated with the tramming of equipment in room-and-pillar systems. Since the longwall system is more amenable to automation, it is inherently safer than room and pillar. Remote control of all face equipment from gate roads will obviate the exposure of men in the face area. Considering what has been said, it seems a paradox that more longwall installations are not found in the United States. However, with favorable mining conditions in relatively level seams of adequate height under shallow cover, it has been possible to develop highly productive, mechanized, room-and-pillar systems. Thus there has been no real incentive to employ longwall in the United States. In Europe, mining companies usually have very little choice between the two systems. Pitching seams of low height located at great depth dictate the use of longwall methods. With depletion of its readily accessible reserves, mining conditions will be similar to those now prevailing in Europe, and an increase in the use of longwall in the United States can be anticipated.

Jan 1, 1963

By S. S. Peng

Horizontal stress is an important factor that contributes to roof failure during longwall entry development, especially when the immediate roof is weak. In this paper, the effects of stress angle between the maximum horizontal stress and entry development and stress ratio of the maximum to minimum horizontal stresses on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method. The results have confirmed that stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the stress angle is about 60° to 75° . The stress ratio has also some effects on the roof stresses.

Jan 1, 2000