Search Documents

By Guodong Li, Chenlin Wang, Zibiao Yu, Bo Xu

Abandoned coal mines have many underground space resources, such as roadways, shafts, and gobs. Among them, abandoned roadways are the best gas storage space for underground compressed air energy storage (CAES). However, CAES caverns have high air pressure and strict sealing requirements. Therefore, the stability and sealing of abandoned roadways under high internal pressure must be analyzed. Afterward, the suitability of abandoned roadways used for CAES caverns should be evaluated. In this study, the numerical simulation software FLAC3D was used to calculate the stress, deformation, plastic zone volume, and pore pressure of surrounding rock in an abandoned roadway under 10 MPa internal pressure. The influence of buried depth, surrounding rock grade, and in situ stress state on roadway stability and the effect of surrounding rock permeability on roadway sealing were analyzed. Results showed that the stress, displacement, and plastic zone volume of surrounding rock were affected by high internal pressure when the buried depth was less than 300 m, but high internal pressure had little effect on them when the buried depth was more than 300 m. The suitable range of buried depth was more than 300 m. The optimal choice of surrounding rock grade was I and II, followed by grades III, IV, and V. The optimal choice of in situ stress state was σH > σh > σv, followed by σH > σv > σh and σv > σH > σh. The sensitivity of the stability evaluation parameters was ranked in descending order as follows: buried depth, surrounding rock grade, and in situ stress state. When the surrounding rock permeability was less than 1 × 10− 14m2, the 24-h air leakage rate of the roadway was less than 1%. The suitable range of surrounding rock permeability was less than 1 × 10− 14m2.

May 23, 2023

By C. Newman

"Over the past decade, as conventional underground deposits have been depleted, mining operations have been forced to produce at greater depths and in more geologically and geometrically challenging conditions. As such, there has been a global increase in the application of cemented paste backfill (CPB) in tabular deposits utilizing open stope mining method with a delayed backfill placement. Despite the extensive use of CPB, many fundamental factors affecting the design of safe and economical fill structures are still not well understood. A critical issue in the design of backfilled stopes is the determination of stress states within the fill material itself as well as the surrounding rock mass. Analytical equations provide a means of quickly evaluating the effectiveness of a given design. However, in developing these equations large assumptions are implemented to simplify the design problem. It is important that one understands these simplifications as well as their effect on the overall design. This paper investigates common analytical equations utilized in the evaluation of single vertical backfilled stopes and their assumptions through comparisons to numerical modeling results. INTRODUCTION AND BACKGROUND As the mining industry continues to produce at greater depths and in more geometrically and geologically complex conditions, cemented paste backfill (CPB) has gained traction as a means of providing localized ground support in modern stope-and-fill mining operations. The application of CPB in stope-and-fill mining as a ground support material has led to the reduction of mine waste costs, while increasing both mine production and stability. In an attempt to achieve total extraction of the mining reserve, stope-and-fill mining operations often employ a primary-secondary excavation-support sequence (see Figure 1). In this practice, primary stopes are initially excavated and then backfilled in a two-stage pour; plug and final pours. During the first stage (plug), a CPB material with increased cementitious content is placed at the bottom of the stope providing a strong base from which to build a backfill structure as well as protect mine works from material breakthrough. Following placement, the backfill plug is allowed to cure to a given strength as designated by the mine design. Upon achieving the required cure strength, a less cementitious CPB material is used to backfill the remaining stope area. This is referred to as the final pour stage. With all primary stopes excavated and supported using backfill, the extraction of the secondary stopes commences as primary stopes are utilized as artificial pillars. While the application of CPB in a primary-secondary extraction-support mining sequence allows for a substantial increase in reserve recovery, it is imperative the mining personnel and planning engineers have a clear understanding of the material’s behavior and stress interaction with the surrounding rock mass to ensure the most efficient, cost-effective, and safe extraction of underground deposits."

Jan 1, 2018

By T. Patten

A method for stabilizing mercury containing waste for landfill disposal would be a very cost effective solution for industry. A mercury polythiocarbonate material which is made via a metallurgical process passes a traditional TCLP for mercury. The mercury polythiocarbonate material was subjected to a more thorough evaluation, the Integrated Leaching procedures as described in Kossan (1) and Sanchez (2)The procedure involves leaching the mercury polythiocarbonate material at varying pH and sample size to liquid. The procedure had to be adapted for small sample sizes and finely divided materials due to the product characteristics and available material. The leachates were evaluated and found to be stable within common environmental pH values. The performance details on how Inter-Mountain Labs met the leaching requirements of the procedures and the analysis of mercury are presented.

Jan 1, 2012

By Abhishek Kumar, T. G. Sitharam, Surender Singh

The height of tailings pond (TP) embankments is frequently raised to accommodate the ever-increasing volume of tailings released by the mining industries. Excess pore water pressure (EPWP) may develop during the height-raising operations, which can affect the overall stability of TP. This article presents a detailed stability analysis for the embankments of an existing TP, the height of which was increased twice utilizing downstream (D/S) and upstream (U/S) construction techniques. A rigorous two-dimensional transient fully coupled-stress-pore pressure analysis is performed in the finite element-based package RS2 to examine the build-up of EPWP during different stages of construction. Furthermore, an attempt is made to investigate the feasibility of future height raising, with due consideration given to the influence of embankment raising rates. Results from the analysis show a development of higher EPWP within the tailings deposit in comparison to the embankments of TP, indicating the development of an undrained-like condition. The study further reveals that the development of EPWP is highly affected by the rate at which embankments of TP are being raised. A higher rate of embankment-raising results in the development of greater EPWP in comparison to a lower embankment-raising rate, which may lead to the ultimate collapse of TP. Furthermore, based on the stability analysis, the height of existing TP can be further raised by 4 m (two lifts of 2 m height) utilizing the U/S construction technique. A thorough cost and benefit analyses are however required before implementing the results of the current analysis since the storage capacity of TP is reduced while raising by the U/S method.

May 16, 2023

By P. R. Sheorey, D. Barat, B. Singh

Presented is a stability analysis for a trial stope in a lead-zinc mine. The trial scope would have an excavation width of 20 m with an initial height of 3 m. Filling would commence when the scope was heightened to 6 m. A two-pronged approach to predict the stability of such an opening was used viz. the finite element method and the rock mass classification method. Corroboration is shown to exist between the two methods. Deep borehole extensometer observations during stope extraction have been compared with predicted displacements.

Jan 1, 1981

By M. Akram

Stability assessment of entry roofs is an essential precursor to all underground design. Both multi-seam interaction and longwall mining can subject entries to radical changes in the surrounding stress field. Such loading changes frequently produce instability and failure in the roof, floor and pillars. Roofs are shown to be vulnerable to stress-induced failures, particularly when the load is unsymmetrical. To predict the effects of changes in stress field, roof failure conditions under increasing loads were studied using finite element analysis and body loaded photoelastic models. A large range of geologic conditions were evaluated and incorporated into the model using Monte Carlo methods. Entry analysis using the model showed the roof to be particularly vulnerable to shear with the location of the failure site changing to meet loading and geologic conditions. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Based on this research a roof stability model SESAME was constructed for roof stability evaluation under specified loading conditions.

Jan 1, 1993

By Ebrahim Ghasemi, Mohammad Hossein Kadkhodaei, Mosareza Jalilian

Entry-type mining methods, such as cut and fill method, play a significant role in underground mining, and they are still suitable methods for extracting deposits with irregular shapes and with weak host rocks. In these mining methods, the stability of the open spans is important for improving worker safety and increasing ore recovery. This study focuses on the application of six data mining classification methods, namely multinomial logistic regression (MLR), classification and regression trees (CART), logistic model tree (LMT), decision tree (J48), multivariate adaptive regression spline (MARS), and gene expression programming (GEP), in order to develop predictive models for stability assessment of underground entry-type excavations. For this purpose, a database containing 399 case histories of entry-type excavations from seven Canada underground mines was used. These models predict the stability status of entry-type excavations based on two input parameters, dimensions of the span and rock mass rating (RMR). The performance of developed models was evaluated using six performance metrics namely accuracy (ACC), sensitivity (SE), precision (PR), Matthew’s correlation coefficient (MCC), area under the receiver operating characteristic (ROC) curve (AUC), and performance index (PI). The results showed that all developed models can be used to predict the excavation stability, but the comparison of models indicated that the J48 model provides the highest performance with ACC = 0.900, SE = 0.869, PR = 0.922, MCC = 0.835, AUC = 0.891, and PI = 4.417. Thus, the proposed J48 model can be applied to identify the susceptibility of span instability in the entry-type mining, and if instability has been predicted, the necessary measures, including the use of suitable support systems, can be considered to reduce the casualties resulting from span instability.

Feb 26, 2024

By Gy. Deák

The Romanian mining industry, especially salt mining, is going through a restructuring phase taking into account the Environment Acquis of the European Union1. In order to preserve the centuries-old salt mines and to develop new ones, in the same salt rock deposit, the long term stability assessment of the saline complex is very important. This case study refers to the Praid salt mine, which includes old salt mines, with impressive sizes, located above the new mines, with activity in progress, in order to provide the means and solutions for efficient conservation and sustainable exploitation for the salt resources. The DKRControl method and FLAC 3D code were used in order to assess the confidence level for the computed prediction of the stability of the salt mine complex salt.

Jan 1, 2008

By S. S. Peng, V. Z. Sun

One of the major concerns of ground control in a coal mine is the prevention of roof, pillar and floor failures of the mine entry. To better design and evaluate the stability of a mine entry within a certain level of confidence, a reliability approach is introduced. The advantage of using the reliability approach, rather than the conventional safety-factor (SF) method, is that it not only takes variability of both rock/coal properties and stress into consideration but also assesses the stability of each component and the mine entry as a whole. Therefore, it is anticipated that by using this approach the current ground-control technology in a coal mine will convey a better sense of confidence. The results of a case study show that there is a significant difference in mine entry stability between the current design method and the reliability approach.

Jan 1, 1999

By V. Z. Sun

One of the major concerns of ground control in a coal mine is safety against failure of one of three components (i.e. roof, pillar, or floor) of the mine entry. In order to better design and evaluate stability of the mine entry with a certain confidence, a reliability approach is introduced rather than using the conventional safety factor (SF) method only. Advantages of using the reliability approach is that it not only takes variability of both rock/coal properties and stress distribution into consideration, but also assesses the stability of each component and mine entry as a whole system. Therefore, it is anticipated that, by using this approach, the current ground control technology in coal mine will convey a better sense of confidence. The results of a case example show a significant influence on the current design concept and stability evaluation of mine entry.

Jan 1, 1997

By C. E. Brechtel

Bench cut-and-fill stopes with heights between 85 and 105 ft are being excavated in the lower levels of the B-NEATH Zone. Estimates of pillar strength and pillar loading indicated a high probability of pillar failure. Some changes in mining practice were made to minimize impacts of pillar failure and a rock mechanics instrumentation program was employed to monitor stability during mining of the first stopes. Limited pillar failure, in the form of destressing, was observed in the initial stopes; however, global stability during mining was good. Instrumentation data indicated that predictions of pillar strength and stress were quite close to field results.

Jan 1, 1989

By K. G. Sutterer, P. T. Wang, R. Sweigard

One possible alternative for the disposal of flue gas desulfurization (FGD) by-products is to use it as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation in stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48% and the peak stress could be decreased by about 58%. The study indicates that fairly weak FGD materials can eventually lead to the stability of backfilled highwall adits.

Jan 1, 1998

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

As the surface reserves are being depleted, more and more stone operators are seeking underground mining options. Stability of underground openings is a major concern for the safety and productivity. This paper relates to a field study conducted at a large underground limestone mine in Central Pennsylvania. Identification of hazards leading to ground failures and assessment of roof fall risks are important in mitigating injuries. Field observations at this mine were integrated with Roof Fall Risk Index (RFRI) mapping software recently developed by West Virginia University. The system is designed to combine field study data related to geologic factors, mining-induced damages, roof profile, and ground water influx to generate RFRI maps. The mine has adopted a proactive ground control program consisting of comprehensive examination of drilling and bolting logs; precision surveying of roof and rib; accurate mapping of cutters, falls, and geologic structures; and installation of extensometers and microseismic monitoring systems. Investment of time and resources has eliminated fatalities and lost-time injuries due to ground fall. This paper presents the geologic settings, mining conditions, ground control issues along with risk management and control techniques adopted at the study mine.

Jan 1, 2009

By Wang Hongwei, Wu Yongping, Cao Peipei, Jiao Jianqiang

Fully mechanized top caving mining of steeply inclined extra-thick seams with variable angles has complex roof rock movement, failure, caving, and filling mechanisms. Moreover, the variable-angle coal seams make rock–equipment stability control challenging. We analyzed rock deformation and failure mechanisms, overburden bearing structures, and working characteristics of supports through physical simulations, field tests, and theoretical analysis of the no. 120210 working face of Zaoquan Coal Mine. Overburden rock movement has distinct regional characteristics, with a large caving height (to the main roof layer) in the upper area, and lower caving height (to the lower main roof) in the lower area. Support loading is regional and unbalanced along the inclined direction. The critical layer of overlying strata migrates, and bearing structures formed by breaking the critical layer exhibit cross-layer generalization along the inclination. The upper region has a cantilever beam structure in the basic roof rock layer; the lower region has an inclined masonry structure with multistage ladders in the breakage basic roof rock layer. Application of a false-inclined working face layout with the tailgate ahead of the headgate and an arc arrangement (radius 28.65 m, arc length 10–20 m) in variable angle areas, and regional control of support working resistance and top-coal caving amounts, control regional failure overburden. Safe and efficient mining was achieved, with the monthly production and recovery rates reaching 344,900 t and 85.86%, respectively. Our results expand the scope of fully mechanized top caving mining and have important theoretical and technological significance.

Nov 23, 2020

By Hongwei Wang, PEIPEI CAO, Yongping Wu, JIANQIANG JIAO

In the fully mechanized top caving mining of steeply inclined, extra-thick seams with variable angles, the mechanisms of roof rock movement, failure, caving and filling are highly complex. This is due to the varying angle of coal seam in different areas, which makes rock–equipment stability control challenging. In this paper, the surrounding rock deformation and failure mechanisms, bearing structure of the overburden, and working characteristics of the supports are elucidated. The principle and key technologies of rock–equipment stability control are presented and applied to control the overburden of the regional failure and realize safe and efficient mining of the working face.

By T. Carageorgos

The removal of arsenic from process streams as ferric arsenate compounds is being practised by mining industries. Therefore, the solubility and stability of these solids is of considerable importance to the mining plants that have to keep the environment free from pollutants. There is some information on the solubility of the ferric arsenate compounds, mainly on scorodite, obtained from synthetic solution. However, there is not so much work on ferric arsenate compounds formed at high temperatures (175 - 230°C) during the leaching process. In the present work, the solubility of the ferric arsenate compounds formed during acidic pressure oxidation of arsenopyrite is presented. The results of the solubility tests showed that the ferric arsenate compounds formed at high temperatures (200 - 230°C) and high pressures (1034 - 1551 kPa 0,) released arsenic into solution in amounts less than 1.2 ppm and iron in amounts no higher than 1.0 ppm. So, they seem to be potential compounds for arsenic and iron disposal.

Jan 1, 1998

By Ralph P. Hackl

Biooxidation processes for treating arsenical and other types of refractory gold ores are touted by many as being simple, inexpensive and environmentally friendly. One of the advantages claimed by proponents of biooxidation is that arsenic is disposed of as insoluble ferric arsenate which is suitable for long term disposal in tailings ponds. However, there is considerable controversy as to the stability of ferric arsenate with respect to re-dissolution of arsenic. In particular, there is concern that the amorphous ferric arsenate produced at low temperature is not stable, especially at the alkaline pH's required for cyanidation. There is a general lack of published information on the stability of arsenical bioleach tailings. Past work on ferric arsenate stability has usually involved purely chemical systems and the use of synthetically prepared precipitates. Upon completing the Salmita bioleach pilot plant campaign (Hackl and Wright, 1989) the author had the opportunity to test the stability of the arsenical bioleach/cyanide tailings which were produced. This paper summarizes the results of that work.

Jan 1, 1990

By J. F. Lupo

Heap and valley leach operations rely on solution collection piping placed within the heap to enhance both solution recovery and to assist overall solution management. The most common piping used in leaching operations is solid or perforated High Density Polyethylene (HDPE) pipe and Corrugated Polyethylene pipe (CPE). These pipes are widely used because of their low cost, ease of installation, durability, and flexibility. The typical recommended maximum design depth of burial for HDPE and CPE pipes is on the order of 30 meters (100 feet). However, ore heap heights at many facilities exceed 30 meters and some are now approaching 180 meters (600 feet) in height. At very high ore heap heights, the stability and performance of HDPE and CPE pipes becomes a critical issue for leaching facility design and operation. Failure of solution collection piping can lead to poor solution recovery, high hydraulic heads on the liner system, and in some cases, unstable ore slopes due to high solution pressures near slopes. This paper presents a review of methods that have traditionally been used to evaluate pipe stability under high normal loads. A common shortcoming of these methods is the inability to account for beneficial effects of ore arching around pipes and the time-dependent creep (stress relief) behavior of polyethylene (PE) materials. A new analytical approach is developed and presented which includes the effects of ore arching around pipes and creep of PE materials. The results of the new approach show that PE pipes will deform under high heap loads, but can remain stable and functional. Pipe stability is shown to be dependent on the type of pipe backfill and initial backfill compaction. The new approach represents a useful tool for designing applications for PE pipe under high normal loads.

Jan 1, 2001

By N. Sheikh

In galena flotation, lead ethyl xanthate, Pb(EtX)2, is precipitated and is physically adsorbed in the form of multilayers on the chemically adsorbed first layer of Pb(EtX). 1,2) The solid particles are coated with layers of Pb(EtX)2 in heterogeneous manner over surface areas possessing both anodic and cathodic character (3,4) It is anticipated that the mode of formation of Pb(EtX)2 and the number of ions present, together with stable or unstable by-product species, have great influence on the surface characteristics of galena. The information obtained from a study of these parameters may have important practical applications in flotation. Lead ethyl xanthate is sparingly soluble in water. The metal and xanthate ions released to the aqueous solution during its dissolution undergo various types of reactions depending upon the pH values of the system. Extensive work (5,6) has been carried out to elucidate the mechanism involved in acid decomposition of xanthate ions. Different decomposition paths (7,8) have been proposed for the hydrolytic decomposition of xanthate in neutral and alkaline solutions, The concentrations of lead ions vary due to a number of chemical reactions, regulated by the pH and the temperature of the bulk phase. The hydrophobic character of Pb(EtX)2 may change with the nature of chemical reactions. Some of the numerous by-product species in solution may adsorb on the solid and change the properties of surface film either favourably or adversely. The flotation performance of galena, therefore, may depend to a considerable extent on the physical and chemical stabil¬ity of Pb(EtX)2 layers. Since little work has been reported in literature dealing with the stability of Pb(EtX)2 and its correlation with the flotation of galena, attempts have been made In this study to evaluate the behaviour of freshly formed Pb(EtX)2 in aqueous systems at various pH values.

Jan 1, 1971