Search Documents

By Klaus Stoss, Bernd Braun

The sinking and lining of a large mine shaft with 8.0 m i.d. and 1,133 m total depth is described in detail. The ground freezing method was applied to safely sink the shaft through unstable, waterbearing strata. Following a brief introduction to the geological and hydrological conditions and the owner's shaft requirements, is the general technical concept to sink and line the shaft. Particular emphasis is put on the lining system which has to provide stability and absolute watertightness for the lifetime of the shaft, even though mining takes place in its immediate proximity. Machinery and equipment used to execute the work are mentioned and commented. Furthermore, the excavation and lining of the large filling stations using rock anchors and shotcrete are described. Details on performance rates are given.

Jan 1, 1983

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerks-dorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7,988 acres or 12.5 square miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26 feet diameter down-cast shaft and a 22 feet diameter up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month.

Jan 1, 1964

By F. J. Klingler, R. Hausmann, K. M. Swaffar, J. C. Neyer

This paper presents the results of a study of case histories of projects on which sinking caissons were used to construct shafts for tunnel construction and other underground works. Design methodologies are reviewed with respect to the impact of soil and groundwater conditions on the performance and constructability of sinking caissons. Factors which have led to success or failure are reviewed and evaluated, and recommendations for future investigation, design and construction activities are presented. Cost data for five recent projects are reviewed and compared to the cost of shaft installation by other means.

Jan 1, 1997

By A. G. Provost

On April 3, 1981, Harrison Western Corporation was awarded a contract by Amax Alloy - A Division of Amax Inc., to sink the Henderson #5 ventilation shaft. The project was located on the Henderson Mine site 88 kilometers west of Denver near the town of Empire, Colorado (Figure I). The Henderson No. 5 Shaft, located in an Alpine environment at an elevation of 3145 meters, was a 9.8 meter diameter concrete lined shaft with a total depth of 793 meters. Work started and continued with Harrison Western employees until January 15, 1982. At that time, Amax made the decision to continue the shaft-sinking with their own labor, and with Harrison Western providing supervision under a management service contract. Shaft sinking continued under this arrangement to October 1, 1982, at which time Amax put the Henderson No. 5 project on standby status until further notice.

Jan 1, 1986

By Bruce A. McKinstry

For many major mining projects the time frame from initial planning to production can be measured in terms of decades. Hecla's Silver Shaft project, which is scheduled to go into production by the end of this year and includes a complete surface facility, shaft with an ultimate depth of 2,348 meters (7,700 feet), complete ore pass and loading pocket system, and 610 meters (2,000 feet) of development drifting and stope preparation, was initially concieved in the Fall of 1979. This duration of a mere four years from conceptual engineering to production is a testimonial to what can be accomplished when a progressive mining company and an innovative contractor work together as a team rather than developing into two warring camps as often happens.

Jan 1, 1983

By F. Cappel

Except in a few special cases, it is necessary for solid fuel direct reduction in rotary kilns that iron-bearing materials be charged with a minimum grainsize of approx. 5 mm. For fines not usable in such form, the combination of sintering - as agglomeration step - and direct reduction were investigated. During reduction of sinter in rotary kilns prevail dependencies on sinter quality and varying reaction parameters, owing to the use of different coals, which led to a definite statement as to what quality sinter must have and which coals can be used.

Jan 1, 1983

By Richard C. Corson

The new 9300 TPD sinter plant being built for China Steel Corporation is incorporating the latest computer technology for plant control systems. The control system will use a central computer and distributed micro-processors to control instrument loops and switching logic in the blending yard and sintering plant. All plant functions, including combustion and fan controls, will be controlled by remote microprocessors located throughout the plant, and connected by a communications link to the centrally located computer and control room. The design, programming, construction and operation of a microprocessor based control system presents new challenges to the control engineer. With microprocessors in the control system, more power exists in the individual control loop and many supervisory functions may be added at the loop level. The specification of the microprocessor system and the resolution of hardware design and control system design can lead to development of powerful systems capable of higher level control and optimization functions

Jan 1, 1981

By H. E. Rowen

I hope my title is not confusing; even more so that I am not. Actually pelletizing and sintering, meaning both the formation of pellets and the hardening of them, are closely related to each other and to phenomena of nature. Figure. 1 This many-celled porous structure, frozen as it was at the fusion temperature and was being frothed by fast-moving gases, may be considered a typical piece of sinter. The same structures have been found in natural ores.

Jan 1, 1962

By Stephen J. Crittenden

Deep gas and oil production has been substantially increased over prolonged periods through the use of sintered bauxite propping agents. Since its inception in 1976, over 170,000,000 pounds of high strength ceramic proppants have been employed. Recent field evaluations and economic analysis demonstrate the superiority of sintered bauxite proppant over quartz sand. This paper describes the development, application, field results, and product evolution of sintered bauxite.

Jan 1, 1983

By Shinzaburo Kato

In 1977 Kawasaki Steel Corporation (KSC) built No. 6 BF (Blast Furnace) with an inner volume of 4 500m3 as part of our program to produce 8.5 million tons of crude steel a year at Chiba Works. As the primary raw material to be used in No. 6 BF, we decided to use sintered ore, because we were confident in the obvious advantages of our technology developed by that time on sintering and BF operation using sintered ore. At Chiba Works, however, we had no space for the construction of a sinter plant, so we decided to build it abroad. Sintered ore is easily crushed and degradated. Producing sintered ore at a point far away from the blast furnace and transporting it across the ocean was the world's first attempt. To successfully realize it, we conducted a series of fundamental surveys and studies with special stress on the real aspects of degradation of sintered ore caused by long-distance transportation and handling and the ways and means to prevent the degradation. As a result, we decided to build a plant on the Mindanao of the Philippines.

Jan 1, 1982

By E. D. Stephenson

As part of the British Steel Corporation?s development plan during the 1970?s, it was decided to concentrate its bulk steelmaking processes based on the BOS at 4 major Works with access to deepwater ore terminals, for the supply of high-grade imported ores. These 4 sites were at: - 1. Rarenscraig Works in Scotland where the ore terminal would be hilt at Hunterston on the west coast some 50 miles away. Bavenscraig was already an integrated Works but suffered from having to discharge ore 27 Glasgow tenxinus on the River Clyde, which could only accommodate vessels up to 25,000 tonnes. In the future, ore was to be unloaded at Runterston and shipped by a rail-link into Ravenscraig, The new ore terminal would have the potential to unload vessels up to 300,000 tonnes. - 2. Port Talbot Works in south Vales where the existing harbour was developed to discharge large ore carriers. This again was an existing Integrated Works and the benefits of the new harbour also applied to Llanwern Works which was another integrated Works some 50 dies to the east, which would now receive ore from Port Talbot.

Jan 1, 1980

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By Rob Dorey

The disposal of mine waste continues to be one of the main controlling factors in the economics and feasibility of project development. Particular to gold and precious metal mining, waste disposal is further complicated by the environmental and political implications of the use of cyanide. Regulatory compliance criteria have partially dictated and can be anticipated to further dictate the approach and methods of tailings disposal. To develop practical, economic, and environmentally acceptable tailings disposal systems within these criteria requires the use of common sense approaches and the application of available technology. Waste disposal is typically considered during the pre-feasibility stages of project evaluation. At this time, the main emphasis is on the economics and practicality of extracting the metal values from the ore. Frequently, the result of this is that the nature of the tailings and the ability to dispose of the tailings is prejudged. It is also frequently the case, however, that during the feasibility stage and project permitting, the requirements for tailings disposal become paramount.

Jan 1, 1998

By D. D. Potter

ABSTRACT OF ORAL PRESENTATION Extraordinary conditions are often encountered when designing large blasts for in situ mining methods and spatial or innovation techniques are sometimes required. Some of the considerations in designing these large blasts will be discussed with emphasis on those factors that concern powder factor, rock movement and fragmentation. Sources of basic data will be described, along with some of the methods for obtaining these data.

Jan 1, 1977

By P. A. Tuzinski, L. J. Dahl, N. R. Adamson, S. E. Brink, R. L. Blake

The US Department of the Interior, Bureau of Mines is developing a process to selectively extract manganese from oxide ores as part of its in situ mining research program. The Bureau is conducting site characterization studies of two manganiferous iron-formation deposits. These studies include: drill core, regional stratigraphic relationships from the existing geologic database, ore body geometry, geologic structure, hydrologic conditions, accessibility of ore minerals to leach fluid, surface subsidence potential and data collected from laboratory leaching experiments. This information is being used to evaluate the technical, environmental and economic feasibility of in situ mining of manganese for these two deposits. This paper will focus on the stratigraphy, mineralogy, ore textures, fractures, permeability and porosity as they relate to in situ mining.

Jan 1, 1994

By Linda J. Dahl

The U.S. Department of the Interior, Bureau of Mines is developing a process to selectively extract manganese from oxide ores as part of its in situ leach mining research program. The Bureau is conducting site characterization studies of two manganiferous iron-formation deposits which include: drill core, regional stratigraphic relationships from the existing geologic database, ore body geometry, geologic structure, hydrologic conditions, proximity of ore minerals to the leach fluid paths, surface subsidence potential, and data collected from laboratory leaching experiments. This information is being used to evaluate the technical, environmental, and economic feasibility of in situ leach mining of manganese for these two deposits. This paper will focus on the stratigraphy, mineralogy, ore textures, fractures, permeability, and porosity as they relate to in situ leach mining.

Jan 1, 1992

By Jeffrey D. Swanson, Martin L. Smith

Smelterville Flats in Idaho's Silver Valley has been designated as a Superfund site due to metals contamination resulting from the use of the South Fork of the Coeur d'Alene river as a tailings impoundment earlier in this century. Tailings average in excess of 4% lead and zinc. Selective mining of highly contaminated zones is being studied as one of several possible remediation strategies. The first step towards remediation is the examination of the stratigraphic, geochemical and spatial characteristics of the site. These characteristics are related to appropriate sampling protocols and exploratory sample grid design. Special problems involved in the geostatistical analysis of tailings are emphasized.

Jan 1, 1992

By Ben L. Seegmiller

INTRODUCTION Site characterization using oriented borehole core is the subject of this paper. Borehole core is a standard source of data for rock mechanics investigations. Oriented borehole core provides data whereby the geometric orientation of various geologic discontinuities (faults, joints, bedding, etc.) may be determined. The orientation and strength characteristics of discontinuities are important in many engineering investigations and in particular, in slope stability analyses. In heavily vegetated or soil covered situations, oriented borehole core may provide the only means of assessing the subsurface planes of weakness which characterize the site. The purpose of this paper is to briefly describe various methods or orienting core, core characteristics which may be logged and the methods of processing and using the data for site characterization.

Jan 1, 1977

By Jiang Shuguang, Zhang Huicheng, Wang Xingshen

Based on the experience about determination of properties of the main fan in mine shaft, this paper relates at length how to reasonablly select test system, test methods and test instruments, how to appraise the reliability of determination results, and how to effectively control the adjusted air etc. The merits and demerits of the two methods of determining air with Nine- Anemometer and Pitot meter are compared.

Jan 1, 1991

By Gennaro G. Marino

During the preliminary design stages of the Illinois Division of Natural Resources(DNR) building, it was discovered that an old coal mine was present some 70 m (220 ft) beneath the building site. The new DNR building to be constructed is 36 m (120 ft)wide and 134 m (440 ft) long. It has three stories above grade and abasement level. The building is oriented north-south and has east and west ponds next to it (Fig. 1). The building is located on the State Fairgrounds in Springfield, IL. Given the history of surface subsidence of these underground coal mines in the Springfield area, there was concern about the potential for future subsidence at the building site. Mine subsidence events in the area have resulted in more than 0.9 m (3 ft) of settlement and have caused significant structural damage.

Jan 1, 2000