Search Documents

The estimation of the spatial variation of the b-value of the Gutenberg- Richter relationship is important for both the general interpretation of the mechanism of rock mass response and seismic hazard assessment. The interpretation of b-value as a parameter of rock mass response is discussed in this paper. The methods applied to evaluate the spatial variation of b-value and the algorithm for obtaining the magnitude of completeness and b-value for subsets of data are presented with some verification analyses. The algorithms presented enable the automation of a spatial evaluation of b-value.

Jan 1, 2014

By J. Jacob

Diamondiferous linear beaches in Mining Area No. 1 have been the mainstay of Namdeb?s diamond production for more than 80 years. Most of the onshore beaches have been mined out, but in recent years mining has been extended offshore into the surf zone through a process of beach accretion. A total of 61.6 million carats has been produced from the gravel beaches since their discovery in 1928, and Mining Area No. 1 is considered to have great remaining potential from areas currently submerged under water. To date, the surf zone has remained largely unexplored due to the consistently strong winds, currents, and large waves which make access to this area extremely difficult. This paper describes the processes used in developing a practical methodology for exploration of the surf zone in a domain extending approximately 22 km long in a northwest?southeast direction and 0.3 km wide in a perpendicular direction adjacent to the current Mining Area No 1. The vigorous surf zone poses multiple technical challenges in terms of obtaining geological and diamond information. In order to access the area for sampling, a jack-up walking probe drill platform (PDP) with a 5-inch diameter reverse-circulation drill has been developed to carry out exploration drilling in the dynamic surf zone. The hydraulically driven platform has eight legs, each of which is 18 m long. Four of the legs are in fixed positions on the fore and aft sides of the platform. The other four moveable legs are fitted to sliding frames attached to the port and starboard sides of the platform. The sets of fixed and moveable legs can be raised and lowered by hydraulically powered jacking stations. By alternately lifting and lowering the sets of fixed and moveable legs in conjunction with the frames moving back and forth horizontally, a walking action is performed by the PDP. The platform can walk at a speed of 10?15 m/h, depending on weather and footwall conditions. Optimization of sampling for diamondiferous gravel occurrence in Mining Area No.1 was undertaken through creation of a virtual orebody on which different sample configurations were tested. The input data for the construction of a virtual orebody comprises a set of drilling data, collected from recently accreted areas directly adjacent to the 22 km × 0.3 km target domain. The input drilling data covers only 34% of the domain, and for the purpose of this study, a single realization is deemed to be sufficient. The texture obtained from using only the drilling data to construct a simulation did not make geological sense; hence it was necessary to make use of analog data in order to improve the simulation. The first analog data used consists of the gully patterns found in the metasedimentary Precambrian bedrock footwall. Gullies are, in general, gravel filled and it is fair to assume that gully patterns form a subset of the total gravel occurrence. Total gravel occurrence includes marine terraces (governed by sealevel stands) above bedrock peaks, together with gravel within gullies below bedrock peaks. The second analog ?data? introduced is through the use of ?expert interpretation?. The indicator drilling data is interpreted by expert opinion and the 2-dimensional result is hand-sketched, digitized, and then pixelated. The pixelated data set is then used as input for variogram calculation. This study cannot provide a single definite optimization result as the nature of the data does not permit this. The use of different validation approaches (conditioning data, where available; expert interpretation; and gully pattern data), however, can give a very good indication of how to balance sampling effort with de-risking aspects related to geological continuity. Work undertaken by sampling the simulation will give an assessment of the relative probabilities of determining gravel occurrence in the study area. This study showed that a 50 m × 400 m cross-configuration will be a good initial sample spacing for highlighting areas where gravel may be absent, and further infill drilling may be required. The relative efficiency of a 50 m × 400 m cross off-set sampling configuration has been demonstrated using a trumpet curve versus sampling effort when using kriging as the estimation method. Keywords sampling configuration, marine diamonds, orebody simulation.

Jan 1, 2014

Models are used in engineering to reproduce reality as faithfully as possible so that the expected response of a system for given actions or inputs can be determined. In the field of rock engineering, both empirically based and numerical models are widely used to determine the likely response of the rock surrounding excavations. Many of the empirical models are developed from statistical analysis of case histories or from direct observation; however, empirical models are limited because they should be used only within the range of conditions of the observational database. Synergy exists between empirical and numerical models, because empirical models can be used to calibrate and validate numerical models. The empirical approach can benefit from the capability of numerical models to investigate specific mechanisms, which would not be possible using observations alone. Two cases are presented in which the synergy between empirical and numerical models is demonstrated. The first case examines the analysis of discontinuity effects on the strength of slender pillars in limestone mines, and the second case evaluates the effects of stress orientation on coal mine entry stability. It is concluded that numerical model calibration and verification comprises an important first stage in the successful application of models in rock engineering design. Application of numerical models allows mechanisms and interactions of various parameters to be analysed, greatly improving the understanding of the system. The improved understanding can be used to extend the application of empirical design methods, resulting in improved safety and efficiency of rock engineering designs.

Jan 1, 2014

By S. G. Mgenge, J. D. Steenkamp

Tronox Namakwa Sands operates two ilmenite smelters for the production of high-titania slag and low-manganese pig iron. Slag or metal is tapped from one of two product-specific, bi-level tap-holes. In this paper the refractory design specific to the tap-hole refractory layout is described, as well as practices for slag and metal tapping and refractory maintenance. Further developments planned are briefly described.

Jan 1, 2014

By J. H. Cloete, S. M. Bradshaw, D. K. Chibwe

"The primary function of a tundish in the steelmaking industry is to serve as a buffer tank, accepting molten steel from the batch ladle process and allowing it to be cast continuously. However, modern steelmaking has more stringent demands for the quality of the steel product, requiring increased control over the properties of the molten steel before casting. For this reason tundishes have been developed as metallurgical reactors to serve as the final step in refining of the molten steel by removing non-metallic inclusions, preventing the formation of new inclusions, and promoting chemical and thermal homogeneity. In this study the flow behaviour in a four-strand tundish was investigated by means of a half-scale water model as well as numerical modelling. Both the numerical study and physical model were used to characterize residence time distribution (RTD) in the vessel and calculate properties pertaining to the tundish flow regime. Three different tundish configurations were investigated: a bare tundish with no flow control devices, a tundish with a turbulence inhibitor and a tundish with both a turbulence inhibitor and a dam.The physical and numerical models showed that a tundish without flow control devices was prone to significant short-circuiting. A tundish with a turbulence inhibitor was shown to be successful in preventing short-circuiting and provided surface-directed flow, which aids inclusion removal in the slag. Despite the benefits of the use of turbulence inhibitors, it was observed that the upward-directed flow increased the maximum turbulence kinetic energy near to the surface by approximately 120% compared with the bare tundish. Therefore the potential for slag entrainment should be considered during the design and operation of tundishes utilizing turbulence inhibitors."

Jan 1, 2014

By D. Seke

Metal inventories are usually reported in financial statements of mining companies. However, the value of these inventories can be reliable only if the metals in stock are measured within acceptable tolerances. Reliable metal balancing requires accurate mass measurement, sampling, and chemical analysis. Many mining companies are usually unable to validate the accuracy of metals in inventories at the end of their financial year. This is mainly due to poor mass measurement, sampling, and chemical analysis practices. This has an adverse impact on metallurgical accounting and metal valuation. In addition, it puts a lot of stress on external auditors, who have the duty to recommend the approval of the financial statements to the board of directors. Although a full value chain of metal reconciliation includes the accuracy of Mineral Reserve definition and grade control at the mine, this paper discusses the implementation of best practices for mass measurement, sampling, and chemical analysis at processing plants. This is an important aspect of sampling and reconciliation that is required in order to improve the reporting of inventories in the financial statements of public mining companies. Keywords metallurgical accounting, corporate governance, sampling, analysis.

Jan 1, 2014

By H. Gumede

The challenges of noise emission in the mining industry are well known. These challenges are exacerbated by the increasing trend towards mechanized mining, and there is general consensus that an effective industry-wide Buy Quiet initiative (BQI) will significantly assist in reducing noise-induced hearing loss by minimizing noise at its source. In its endeavours to improve the health of workers, the MOSH Noise Team has facilitated development of a proposed strategy and structure for a BQI. Extensive consultation with stakeholders resulted in support for the initiative. The MOSH Noise Team was advised to solicit the contributions of consulting mechanical and electrical engineers (CM&EEs), whose support is viewed as critical for realization of the initiative, since elimination of noise at source is an engineering challenge, and most procurement standards and specifications are set and managed by engineers. A workshop with CM&EEs and their representatives, as well as group environmental engineers (GEEs), confirmed the urgent need for the initiative and provided valuable insights. The workshop used obstacle based planning techniques to identify the factors on which the success of this BQI will depend. Most potential obstacles to the implementation revolved around proper scoping, leadership commitment, and companies? adherence to the initiative. Lack of involvement by the relevant stakeholders and economic issues were also identified as potential obstacles. Delegates at the workshop felt that the successful implementation of the industry-wide BQI, will depend on the mining industry addressing the specific obstacles. The most critical and urgent issue was identified as the formation of a properly constituted industry-wide BQI task team that includes representatives from critical stakeholder groups and which is mandated and empowered to drive the initiative.

Jan 1, 2014

By N. Mphathiwa

When slope angles are designed during open pit optimization, there is a risk factor applied in steepening the slopes. The steepening of slope angles has implications for the safety and economics of the mining operation. The steeper the slope angles, the greater the probability of slope failure. Although a slope failure will result in added costs, the challenge is to compile an accurate cost-benefit exercise optimizing the economic benefits of the project without exposing mine workers and equipment to unacceptable risk of rockfalls. A balance between the safety of the operation and the economics of the investment is therefore required. The ideal situation is to have a slope monitoring system that will predict slope failure by detecting any ground movement before the actual failure occurs. This early warning will allow the risk factor to be applied with a high degree of confidence, knowing that the risk will be adequately mitigated. The objective of this paper is to provide guidelines on how to design an optimal survey slope monitoring system. It is the authors? view that for a survey monitoring system to yield desirable results, it should adhere to survey principles such as working from the whole to part and consistently cross-checking. The case study used is Jwaneng Mine, and the design strategy outlined can be used as a guideline for developing a new slope monitoring system or to optimize an existing one.

Jan 1, 2014

By J. H. Zietsman, W. J. Leipoldt

"To be able to responsibly develop a multiphysics model of the steel belt sintering (SBS) process used to sinter chromite fines, it is important to have a comprehensive understanding of the process. This understanding was gained through a site visit, observation of the process in operation, and interaction with the operators. Material characterization will also reveal much about the process that is not yet fully understood. A well-defined and representative mass and energy balance will also give valuable insight into the process. The plan for the multiphysics model aims to combine a computational fluid dynamics (CFD) model with a discrete element method (DEM) model.To obtain a more accurate mass and energy balance representation of the SBS process, it was decided to develop a dynamic distributed parameter model of the mass and energy balance. This model will be used to gain better understanding of the SBS process so that a more complicated multiphysics model can be developed later. The reason for this is because the SBS process is very dynamic, with a large temperature distribution throughout the length of the process. In its current state, the mass and energy balance model is capable of handling solid and gas material packages and exchanging heat between these packages where they are mixed, and is able to model the heating of the gas by burning CO gas. The next step in the development of the model will involve enabling it to handle evaporatoin of liquid water, burning of solid carbon in the pellets, reduction of iron oxide in the pellets with the CO gas formed from carbon combustion, and then oxidation of the reduced iron in the oxygen-rich cooling zones."

Jan 1, 2014

By L. M. Sekhukhune

The atmospheric leaching of copper-bearing matte by acidic ferric chloride solution was studied at the laboratory scale. The aim was to achieve maximum copper and nickel recovery by investigating the mechanisms of leaching, as well as identifying the effect of temperature, and concentration of ferric chloride and oxygen. Djurleite (Cu1.96S), hazelwoodite (Ni3S2), and Ni alloy were the primary phases detected in the matte. The quantitative composition of the matte was Cu 31%, Ni 50%, S 13%. Fe and Co constituted 2%, with platinum group metals (PGMs) accounting for 0.5%. A maximum nickel extraction of 98% was achieved using two-stage oxidative leaching at 90°C and 11 g/L Fe3+ as compared to 65% under non-oxidative conditions. A copper extraction of 99% was achieved in the first 45 minutes using two-stage non-oxidative leaching, and copper was recovered from solution by cementation. Three processes took place simultaneously throughout the leaching process, namely: dissolution, cementation/ metathesis, and oxidation. The leaching process was found to be diffusioncontrolled.

Jan 1, 2014

By Sabine Verryn, Johan de Villiers

"Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine analysis. The method however, requires a good initial calibration and periodic checks on its precision and accuracy.Several examples from minerals processing, pyrometallurgy, and materials science show the strengths and applicability of the method. The limitations and sources of error are also discussed.1. IntroductionDiffraction of X-rays by matter has been used for more than 80 years, initially to elucidate the structure of crystalline matter, and to investigate the bonding between atoms. The first development of powder diffraction cameras and the later development of X-ray diffractometers saw the development of methods to identify phases and to try to quantify them in mixtures. A comprehensive database and search-match techniques have been developed over the ensuing years. Effective and accurate quantification had to wait for the so-called Rietveld' analysis where the total diffraction pattern is used and where the crystal structure data for the constituent phases are needed as input. Overlapping of diffraction peaks of different phases is handled without difficulty and reliable results can be obtained in spite of this occurrence.The development of methods for structure analysis from powder data has also progressed rapidly and more and more complex structures are being solved from first principles, i.e. without knowledge of unit cell or space group data. Because of the ease of use of the Rietveld method, it is finding increased application in metallurgy, especially in the quantification of phases of importance in minerals processing, in pyrometallurgical processes, and in materials characterization. This study will examine the principles of the Rietveld method, its application in metallurgy, and finally also the common pitfalls that need to be avoided.2. Rietve1d AnalysisAs the Rietveld method compares the experimental diffraction pattern with one calculated from known crystal structure data, the following data are needed:•,An XRD Pattern with as Iowa background as possible. This should have good resolution and high diffraction peak intensities. With modem X-ray detectors, this can be achieved in minutes rather than hours.•,Instrumental parameters such as goniometer radii and slit sizes are needed. These are the so-called ""Fundamental parameters"". They are used to calculate the shapes of the resultant diffraction peak profiles that are caused by the instrument. The parameters are used to correctly separate the instrumental effects on the diffraction pattern from the sample effects."

Jan 1, 2014

By D. W. Dean, J. A. Ryder

"A computer system designed to assist in maintenance scheduling and costing, and in monitoring the performance of equipment, is described. The emphasis is on the information retrieval and implementation aspects of the system.INTRODUCTIONThe cost of the maintenance of equipment can account for a substantial proportion of the total costs of any large industry. These costs are made up of the following elements:(i) capital expenditure,(ii) maintenance labour,(iii) maintenance spares,(iv) maintenance overheads,(v) production losses.Control of these cost elements cannot be achieved without a system which maintains and retrieves the necessary infor¬mation efficiently.The system should provide engineering management with the information necessary to:(i) establish the cost of maintaining items of equipment,(ii)establish the economic life of equipment,(iii) determine breakdown patterns for the establishment of optimum inspection, service and overhaul frequencies,(iv) establish work schedules for those responsible for the maintenance of equipment,(v) establish the optimum maintenance labour complement,(vi) establish the optimum stockholding of maintenance stores items,(vii) improve the performance of equipment,(viii) justify the selection of a particular type and make of equipment,(ix) establish the reasons for any abnormal usage of materials and labour, and to(x)reduce the dependence on the human element for the control of equipment maintenance activities.Many industries have comprehensive and numerous equipment maintenance records but they experience great difficulty in retrieving the required information in the time available and with the labour available. Many industries do not bother to maintain meaningful records, because of this difficulty."

Jan 1, 2014

By W. P. Roux

Owing to decreasing high-grade ore reserves, there is a need for better understanding of the jigging process to improve the recovery efficiency of finer, lower grade material. The use of positron emission particle tracking (PEPT) was examined as a technique to study the motion of iron ore particles inside a laboratory batch jig. PEPT is a non-invasive method that can provide three-dimensional kinetic data on a particle in laboratory-scale processing units and has been successfully used to study mills, hydrocyclones, and flotation. Experiments were conducted to determine whether PEPT would be a viable technique to study iron ore jigging and what valuable information could be obtained. The results indicated that detailed information on the stratification rate of a particle could be obtained, with adequate resolution to track the particle?s movement through an individual jig pulse.

Jan 1, 2014

By R. G. Coyle

"In an earlier paper the author explored the consequences of price-stabilizing effects, on an industry-wide basis, of various production strategies. These ideas have now been applied to an illustrative case of an individual mine. It is shown that the turning of production and financial policies can affect financial performance over a five-year period by as much as 22 per cent.No generality is claimed for the results and they would differ from mine to mine. It is, however, asserted that the results show that the proper turning of production, reserves and financial policies are more critical determinants of mine performance than has been realised. It is also asserted that the methods of dynamic analysis are the most appropriate means for studying this policy-design problem."

Jan 1, 2014

By Peter N. Calder, Alan Bauer

The complexity of modem open pit load-haul-dump systems is described, and the need for realistic working models is pointed out. Both standard and probabilistic simulation procedures are discussed, probabilistic simulation being indicated as the more powerful and practical technique. Acquisition of the necessary pit operating data required for simulator construction and general modelling procedures are described. Finally, results from a typical open pit simulator are used to indicate the scope of the technique.

Jan 1, 2014

"Chairman: Professor H. S. SICHEL Rapporteur: Miss M. I. WATSONPapers:Unrolling of Copperbelt orebodies by J. H. E. Perry and V. H. WiikAn exploration model for tabular orebodies by G. S. Koch and R. F. LinkHarmonic analysis of copper and gold occurrences in the Arbitibi area of the Canadian Shield by F. P. Agterberg and A. G. FabbriMathematical models of orebodies by M. J. Newton and A. G. Royle Estimation of lateritic-type orebodies by A. JournelIn his presentation Mr Wiik said that unrolling could be regarded as a reversal of the natural process of folding, so that the aim of an unrolling procedure would be the reconstruction of original pre-tectonic conditions. While simply formulated, this aim might not always be achieved. The geometrical relationship between points on the deformed surface and corresponding points on the original surface is process-dependent, and a true reconstruction could be achieved only if the deformation history were known in detail.In this computer unrolling procedure all these complexities were ignored. Referring to one particular marker horizon, Mr Wiik said that it was assumed in the procedure that this marker was deposited as a horizontal stratum and that it had subsequently been deformed by simple flexure-type folding.The procedure allowed the geologist to incorporate his knowledge and conception of the deposit through repeated re-contouring with dummy points. This 'manumatic' aspect of the procedure had proved invaluable, not only in resolving specific unrolling problems but also in making the system more acceptable to the geologists in general.Unrolling served towards removing what might be termed `tectonic noise' superimposed on the primary distribution patterns for regionalized variables such as metal content and orebody thickness. From this point of view, variograms derived on the basis of unrolled-plan co-ordinates should be more meaningful in terms of depositional environment than are variograms calculated from a normal map projection.Mr M. M. Oosterveld remarked that it appeared from the paper that there were problems in applying the unrolling technique to ore reserve calculation, and asked whether there were not other methods that might be used for that purpose.Mr Wiik replied that at present unrolling played only a minor role in practical ore reserve estimation within Roan Consolidated Mines, Limited. The techniques currently in use differed from one orebody to another, but in general they involved projection onto a vertical longitudinal section or a horizontal plan, with subsequent grid interpolation by means of a standard computer contouring package."

Jan 1, 2014

By I. Mc Dougall

Water-cooled copper tap-hole blocks provide an effective means of extending the life of tap-hole refractories, as the lower temperature of the refractory material inhibits wear and other damage and promotes the formation of a protective frozen slag layer. This is particularly beneficial during prolonged tapping cycles. The copper block forms an integral part of the lining, and provides mechanical support to the refractory, facilitating rapid replacement of tapping channel bricks without disturbing the surrounding lining. Safety considerations are an important design factor, and the positioning of the water channels is optimized to prevent leaks although the copper is not in direct contact with the molten fluids during normal operation. Water-cooled copper blocks designed by Tenova Pyromet have successfully been utilized on metal, matte, and slag tap-holes for a number of processes, including nickel, platinum group metals, and mineral wool.

Jan 1, 2014

By F. P. Agterberg, A. G. Fabbri

"A statistical analysis was done on the locations of 718 copper and 1 257 gold deposits in Abitibi. This area of about 20 000 square miles is one of the better-explored metal-producing areas of Canada.Patterns of clusters were studied by harmonic analysis. Several two-dimensional power spectra showed a number of distinct peaks. Sets of crest lines for patterns of interfering waves were constructed on the basis of these peaks. They pass through elongated clusters of deposits which are spaced more or less equally. For copper these periodic regularities in location may coincide with geological structures largely of Archean age (major fractures and sedimentary belts indicating synclinal structures). A directional relationship with swarms of diabase dykes of known ages and distinct attitudes indicates that the gold mineralization is, in part, younger than the copper mineralization."

Jan 1, 2014

By Thomas V. Fame, William E. Porter

"As geological and mining conditions become more complex, and as overall mining economics become more marginal, short- and long-range decision-making regarding multiple-seam surface mining becomes more difficult. The decision-making problem involves a study of economics, cut-off grades and ratios, equipment capabilities, sequencing and selective mining practices.This paper is concerned primarily with multiple-seam mining of bituminous coal. The research has led to the development of an economic decision-making model for use as a day-to-day tool to aid mine operators and pit geologists to decide what and how to mine.The model is designed as an aid for feasibility decision-making in multiple-scam situations and for situations where selective mining is needed or desired. In effect, a simulation of the feasibility and preliminary mine planning phases has been developed. The model is divided into four separate segments: decision-making, simulated mining, cost calculations and the determination of the discounted cash flow return on investment."

Jan 1, 2014

By M. van Schoor

Coal remains South Africa?s most abundant and cheapest source of energy, and there is an ever-increasing necessity for optimal and safe extraction of the remaining reserves. Increasing focus on cost-effective mining and zero harm to the environment and miners has resulted in a shift in attitude towards the application of geophysics in local coal mining and exploration. Furthermore, technological advances have contributed to geophysics being embraced more readily by the coal mining industry, compared to a decade or two ago. Predictably, the growing interest in geophysical technologies has also created a need for education and training in the basic principles and application of geophysical methods, as local coal mining companies generally do not have in-house geophysicists. Consequently, the Coaltech Research Organisation?s Geology and Geophysics working group forum compiled a textbook aimed at addressing this need: to produce a guide for applying geophysics to coal mining problems in South Africa. The target audience for such a book would be coal geologists, mine surveyors, mine planners, and other mining staff with limited or no geophysics background. This paper provides a very brief overview of the book by summarizing key sections and selected examples. In doing so, the value of geophysics to solving a range of coal mining and exploration problems is highlighted.

Jan 1, 2014