Search Documents

By C Katongo

Ground condition at No1. Shaft varies across the mine. The different ground conditions arise as a result of the differences in the rock strength and structure, seismicity and induced stresses in abutments areas. Apart from being a major cause of Fall of Ground incidents/accidents, adverse ground conditions where encountered has affected the rate of development advance as well as production. This implies that for support to be cost effective Geotechnical section has to ensure that support is designed to prevailing ground demand to ensure the safety of personnel and minimize loss of production. We have also seen changes in mining methods as a result of change in ground conditions. To avoid incurring unnecessary costs through remedial works resulting from ground deterioration and collapses of development openings due to inadequate support, the principle in engineering design is ?Do it right the First Time?, and this can only be achieved through good understanding of Geotechnical environment. The paper discusses the different ground conditions encountered in various development ends at No.1 Shaft. It also discusses the principles of ground support, failure mechanisms, types of ground support systems employed, and the different techniques used to select support systems, and quality control techniques in underground support installation.

Jan 1, 2005

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005

By E. Yalçin

The data set often contains one or more secondary variables. These secondary variables are usually spatially cross correlated with the primary variable. The addition of the cross-correlated information reduces the variance of the estimation error by using the cokriging method. The grade estimation results of ordinary kriging and cokriging methods are evaluated and it was found that the estimation variance of cokriging method is slightly lower than ordinary kriging. The effect of variation of block dimension on the estimation results is also investigated and it was seen that the cokriging estimation variance values also decrease as the block dimension increases.

Jan 1, 2005

By Paul Fouchè, Danie van der Merwe

Contents ?Purpose ?Introduction ?Development of RF tracers ?Test procedure ?Results ?Conclusion ?Way forward ?Acknowledgements

Jan 1, 2005

By André Fouché

GFWW Bulk Sample Prep Plant INDEX ?Features ?Flow Diagram ?Pictures of Plant

Jan 1, 2005

By R. Butcher

Mud rushes are hazardous occurrences that have occurred frequently in mines in South Africa, and have been the cause of numerous fatalities in the past. Mud rush incidents not associated with accidents are believed to be common occurrences that are not generally reported. Many such incidents are probably associated with the operation of chutes and box fronts. This paper describes the conditions necessary for mud rush occurrences, postulated mud rush mechanisms, and methods of combating the mud rush hazard.

Jan 1, 2005

By C. Sahyoun

The influence of microwave treatment on copper flotation has been investigated. Comparative batch flotation tests carried out on ore treated at 5?12 kW for 0.1?0.5 s showed that improvements in copper recovery of between 6?15 % could be achieved compared with untreated ore. Both recovery and cumulative grade increased with increasing treatment time and power. A preliminary economic analysis showed that microwave treatment will be economically viable if recoveries similar to those determined on laboratory scale can be achieved on a plant. Keywords: microwave treatment, copper ore, flotation, liberation, recovery

Jan 1, 2005

By SHM Harkema, MKG Vermaak, D R. Groot

Surface Plasmon Resonance spectroscopy (SPR), combined with cyclovoltammetry, has been successfully used to study the interactions between ethyl xanthate, heptyl xanthate, dithiophosphate and propyl trithiocarbonate flotation collectors and a gold surface. Large, easily measurable responses have been obtained in the potential areas where the thiol collectors are known to interact with gold. The four collector types lead to differing SPR maximum values, with longer alkyl chains resulting in higher SPR responses, and the trithiocarbonate leading to the highest response values. The SPR responses differ considerably from the current density response at very anodic and cathodic potentials. There are indications that thiols might still be adsorbed at potentials as low as -300 mV (vs SHE). Keywords Flotation collectors; thiol collectors; cyclovoltammetry; surface plasmon resonance spectroscopy.

Jan 1, 2005

By Dave Deglon, Andrévan der Westhuizen

Objectives ?Survey typical Met Accounting streams at the Zincor refinery ?Determine Precision in Metal Conc?s Measurements for Monthly Met Balance ?Determine the Components of Variance in these Met Acc Values (Sampling, Preparation, Analyses) ??Common plant practice? should be mirrored even though not always in perfect agreement with ?laid down procedures? or ?good practice? ?Mass Measurement and Inventory Measurement was considered in less detail ?not reported here

Jan 1, 2005

By M. Matema

Paper written on project work carried out in partial fulfilment of BSc (Eng.) Metallurgy and Materials Engineering Small and large welded aluminium specimens were tested in fatigue and the results compared with design curves for aluminium in specification BS8118. Metallurgical tests were also performed on the specimens in order to correlate microscopic and macroscopic phenomena. The small-scale fatigue test results were in reasonable agreement with results in BS8118, whereas the large-scale fatigue tests showed that BS8118 is conservative.

Jan 1, 2005

By N. Singh

Merensky Reef is mined extensively within the Bushveld Complex. In previously mined-out areas on the Merensky Reef horizon there are pillars, potholes and remnants that have not been mined. These unmined blocks of ground on the Merensky Reef horizon can influence the mining of the underlying UG2 Reef. The extent of the influence will depend on the size of unmined ground and the middling between the two reef horizons. This paper quantifies the influence of partially extracted Merensky Reef on mining of the UG2 Reef, and aims to provide recommendations for mining strategies, as well as regional and local support to achieve efficient and safe extraction of the UG2 Reef, for various middlings beneath the Merensky Reef horizon. In some cases it was found that relatively shallow UG2 Reef mining could encounter conditions similar to those experienced in deep and ultra-deep mining environments.

Jan 1, 2005

By R. M. Lamya

The kinetics of copper cementation during atmosphere leaching of a Ni-Cu matte in CuSO4-H2SO4 solution was studied as a function of initial copper ion concentration, initial acid concentration, temperature, stirring rate, particle size distribution and pulp density. It was found that all these process variables influenced the rate of cementation. A two-stage rate of reaction was observed inmost of the experiments, with the rate of cementation in the initial stage being slower than that of the subsequent second stage. The increased rate of cementation in the second stage was attributed to the enhancing effect of the surface deposit. The cementation process was found to take place by two different rate-controlling mechanisms. At a temperature range of 50?70°C, an activation energy of 74.6 kJ/mol was obtained, indicating a surface reaction controlled process. At higher temperatures (70?80°C) a lower value of activation energy was observed (18.2 kJ/mol), indicative of a process controlled by diffusion through surface layers. The structural characteristics of the cemented deposit could not be determined in the investigated system where the deposit was mixed with the leach solid residue.

Jan 1, 2005

By H. J. Le Roux, W. B. Drummond

1. INTRODUCTION We have a moral responsibility towards the world to reduce the harmful deposits we emit into the environment arising from beneficiation technologies. Industry has not willingly spent money to limit these emissions because it affected their profit margin with the end result of emitting harmful elements into the environment. Governments have thus rightly stepped in and enforced systematic reduction of these emissions through legislation. In the past beneficiation of sulphur bearing ores was typically done through hydro-metallurgical concentration, smelting, followed by Sulphur removal by converting processes like the Pierce Smith converter. The latter two processes emitted substantial quantities of Sulphur into the atmosphere. Spiralling costs and legislation have resulted in the quest to develop more efficient and environmentally friendly processes to achieve the same end results. New hydro-metallurgical processes like the ActiVox process has completely eliminated the pyro-metallurgical processes. Kansanshi are also operating a similar process. It however elicits other ground water and spillage pollution hazards and problems of it?s own. Various improvements has also been made to the pyro-metallurgical stages, examples being combined smelting and converting with the Noranda reactor, the Codelco CMT furnace, one step flash smelting/converting or the Mitsubishi continuous smelting, converting and slag cleaning process. The new converting processes are also normally enhanced using oxygen leading to higher SO2 gas strength with only a marginal increase in off-gas volume. These processes have led to better efficiencies and a more controlled environment that reduces pollution, but does not eliminate it completely. The fact that there are still more than 70 existing Pierce Smith converter plants throughout the world that needs to be replaced or upgraded at tremendous capital cost, means that we will have the environmental problems for some time to come. The need thus exists to cost effectively get these existing plants into a state where they meet the new environmental regulations, community and safety requirements. This paper will concentrate on just one aspect of this quest, i.e. reduction/removal of off-gasses emanating from the converting of non ferrous sulphur mattes to achieve higher or specialised grades of refined metals.

Jan 1, 2005

By P. J. D. Lloyd

The widely employed IPCC models for the release of methane from underground coalmining operations are reviewed, and put in the context of the South African National Communication on greenhouse gas emissions. Then attempts to calibrate the model via measurements on South African coalmines are described. These attempts failed because it rapidly became clear that the IPCC model, involving methane adsorbed by the coal and released (a) by the depressurization of the strata caused by mining, (b) from the broken coal and (c) from coal remaining in roof, floor, pillars or goaf after mining, was not valid. Instead, measurements showed that the methane release was very variable, sporadically falling to zero. Carbon dioxide concentrations were monitored at the same time as methane, and followed methane concentrations. An alternative model was developed, in which methane was largely displaced from the coal and held in fissures, cleats and pores, which, when intersected by mining, released methane into the ventilation stream. In a key test of this hypothesis, methane concentrations around a continuous miner were monitored both during operation and after shutdown. Even during operation, methane became undetectable. It is hypothesized that heating of the South African coal-seams during the emplacement of the igneous dykes that cut so many of the seams caused displacement of the methane from the coal into the pores. This fissure-held methane, or free methane, is released rapidly once a pathway through the coal into the mine atmosphere is established. In contrast, methane adsorbed in the coal, and measured as the seam gas, desorbs relatively slowly. Measurements suggest that on average about 50%of the adsorbed methane is lost one day after mining. By that time, the coal will have left the mine, so that the remaining seam gas will be released to the atmosphere outside the mine. Attempts to measure methane emissions from surface coal-mining operations showed very little detectable methane. Coal from surface operations, which was milled and exposed to atmosphere, adsorbed gas from the air. It is concluded that methane release from surface operations is probably less than 3Gg/a. It is estimated that the total methane release from the coalmining industry amounts to about 72 Gg/a, as opposed to the National Communication estimates of 323 Gg/a in 1990 and 317 Gg/a in 1994. However, there are large errors associated with these estimates, and it is recommended that the methodology outlined in this report be extended to as many mines as possible to reduce the errors that are inherent in the physical processes underlying the release of methane from South African coalmines.

Jan 1, 2005

By Raphael Banda

1 Initiating Systems ? a definition An initiation system is a combination of explosive devices and component accessories specifically designed to convey a signal and initiate an explosive charge from a safe distance. In the use of explosives, the initiating system performs the functions of transmission and control of the firing signal to each explosive charge. As functional groups, initiating systems may be considered as: Starters Those which provide the initial signal to start the blasting process. Surface systems Products which provide transmission of the starter signal and delay timing (if any) across the surface of the blast outside the blast hole. In-hole systems Products which provide the signal transmission, delay timing (if any) and the initial explosives energy in the blast hole.1 2 Different types of Initiating Systems The initiation systems commonly used in Sub Saharan Africa are: ? Detonating cord and detonating relay systems ? Capped fuse and igniter cord systems ? Shock tube non electric systems ? Electric systems ? Electronic detonators 3 Overview of Electronic Delay Detonator Technology Conventional detonators use pyrotechnic delay elements and the variation of the actual delay periods is at best approximately 1% the nominal delay. The lack of guaranteed precision common to all pyrotechnic systems enhances the likelihood of negative environmental blasting effects.3 For example, take a 500 ms in hole delay. In conventional detonators this means that 95 % of shots fire within 10 ms of the mean. i.e. a window of 20 ms. Taking a fixed interval between shots of 25 ms, with a range of ± 3 ms, a very ragged firing pattern could be expected which in practice would result in non uniform fragmentation.

Jan 1, 2005

Instability in rockpasses at deep levels often initiates as a result of stress induced fracturing of the rock on the walls of the pass. This may then progress to a stage at which the geological structure of the rock mass becomes dominant and permits large joint-defined blocks and slabs to become unstable. In this paper, a technique is described in which jointing parameters and their variabilities?orientations, spacings and lengths?are taken into account in estimating the extent of failure that may develop around a typical unsupported deep level gold mine rockpass. The results of this prediction are compared with the results obtained from a review of pass performance in the gold mining industry.

Jan 1, 2005

By Mike McWha

Drivers to increasing RM use ?Compliance issues ?Section 12 JSE Listing Rules ?Canadian NI 43-101 ?Sarbanes Oxley ?Shortage of African ore reference materials ?Poor perceptions about quality of some local RM?s

Jan 1, 2005

By Gaspard Devos

1. A NEW CONTEXT FOR METAL INDUSTRY Producers and owners of industrial extractive sites are living hard times due to Environmental pressure and liabilities. This is valid whatever the region in the world, it is just a question of time. On one hand, the normative environmental pressure is increasing through more severe regulations and controls on all pollution sources and production materials. [ ] Furthermore, more impurities are extracted and captured, more the volume of the related wastes is increasing. But disposal costs are increasing, disposal areas for wastes are restricted, markets for wastes are limited and technologies for waste treatment are, most of the time, not available. On the other hand, for most of the extractive industries, the costs required to get access to refine primary raw material are killing the profitability of the industry. Definitively, a technological and economical breakthrough is ongoing: extractive industries have to increase their feed from secondary material and to be involved more and more with the recycling business.

Jan 1, 2005

By M. Moys

The use of temperature measurements for unusual applications in the analysis and control of column flotation and milling is discussed. This is followed by a review of some of the authors current research in the application of the discrete element method to the modelling of particulate processes, specifically milling, fluidized beds and chute flow.

Jan 1, 2005

Sampling In The Coal Industry Exploration, Mine, Met and Environmental Sampling EMMES 2005 3, 4 November 2005

Jan 1, 2005