Search Documents

By El-Sayed M. Sherif, J. D. Comins, Erasmus R. M.

Corrosion of copper in aerated acidic chloride pickling (0.5 M HCl) solutions and its inhibition by 3-amino-1,2,4-triazole-5-thiol (ATT) have been investigated using electrochemical techniques and weight-loss measurements, along with Raman spectroscopy. Electrochemical measurements for copper after varied immersion periods of 0, 24 and 48h showed that the presence of ATT and the increase of its concentration significantly decrease cathodic, anodic, corrosion (jCorr) currents and corrosion rates (KCorr), as well as the dissolution currents at 300 mV vs. Ag/AgCl, while increase polarization resistance (Rp), degree of surface coverage (?) and inhibition efficiency (IE%) to a great extent. Weight-loss measurements after different immersion periods of 6 ~ 48h revealed that the dissolution of copper decreased to a minimum and the corresponding IE% increased with ATT concentration increases. The detection of ATT molecules on the copper surface by Raman spectroscopy indicated that inhibition of copper corrosion is achieved by strong adsorption of ATT molecules onto the copper surface. Aerated acidic pickling solutions; 3-Amino-1,2,4-triazole-5-thiol; Copper corrosion; Corrosion inhibition; Raman spectroscopy

Jan 1, 2006

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2006

By M. J. King, A. Weissenberger, W. G. Davenport

Keywords: Pyrometallurgy, sulphuric acid, sulphur dioxide The raw material for sulphuric acid manufacture is clean SO2 gas. It comes from (i) burning molten by-product sulphur; (ii) roasting or smelting metal sulphide concentrates, and (iii) decomposing contaminated organic chemical process sulphuric acid catalyst. Efficient gas cleaning is required for metallurgical and contaminated acid decomposition gases, especially the former. Sulphuric acid is made from SO2 gas by (i) oxidizing the SO2(g) to SO3(g) in contact with supported liquid-phase catalyst then (ii) reacting the resulting SO3(g) with the water component of 98.5 mass% H2SO4, 1.5 mass% H2O acid. This paper discusses the reasons for these process steps and indicates how acidmaking can be controlled and optimized. Special emphasis is placed on SO2(g) oxidation efficiency and how it is influenced by feed gas composition, feed gas temperature, catalyst composition, catalyst bed pressure, number of catalyst beds, and double versus single contact acidmaking. In addition, a review of various other treatment methods for SO2-bearing gases is provided. A brief description of each process is included along with commentary on their technical and economic applicability for use at metallurgical facilities.

Jan 1, 2006

Keywords: Pyrometallurgy, Pretoria University Substantial research in pyrometallurgy at the University of Pretoria started in 1980 with the appointment of Rian Dippenaar to the Iscor Chair, a position that he held until 1996, when Chris Pistorius became the leader of this pyrometallurgy group. This paper reviews the main research themes over the quarter-century from 1980 to 2005, as well as some of the industrial developments that have shaped the research approach. The main topics have been the use of electrochemical sensors for equilibrium measurements, ilmenite smelting, steel processing, and reduction.

Jan 1, 2006

The results of a series of physical model studies of the stability of jointed rock slopes carried out some years ago are described. These models were tested under centrifugal loading. Four ?geological? structures were tested; all had the same joint orientations and strengths, but the relative spacing of the joints was different. The results showed that the mechanisms of failure of the slopes varied for the different models, and the gravitational loads at which failure developed also varied. The following conclusions are drawn from the results of the physical model tests: ?the mechanism of slope failure is by progressive deformations throughout the slope ?the ratio of the spacings between the different sets of discontinuities exerts considerable influence on the slope failure ?in the models tested, the intact material strength had no noticeable influence on the stability of the jointed rock slopes(note that for hard rock, similitude conditions indicate a prototype slope height of 300 to 400 m, and therefore intact rock failure might not be expected under simple gravity conditions, i.e. no tectonic stresses) ?rock slope failures are three-dimensional and in general are not amenable to two-dimensional simplification ?knowledge of the orientations of discontinuities in the slopes does not allow prediction of a unique failure surface, nor of a volume of failure. The volume of failure is determined to a large extent by the plan configuration of the slope.

Jan 1, 2006

By L. Mabiza

Keywords: Pyrometallurgy, circular furnace, PGM, platinum, Peirce-Smith converter, Zimbabwe The Zimplats Smelter, located on the northern part of the Great Dyke, at the Selous Metallurgical Complex, is the only PGM smelter in Zimbabwe. Zimplats? operations currently consist of the Ngezi Platinum Mine, which is a 1.5 Mt/a open-cast and 0.7 Mt/a underground mine, and a Concentrator and Smelter to which ore is transported 80 km by road. The final converter matte product is transported to Impala Refining Services in South Africa for refining and marketing. The Zimplats Smelter operations consist of a concentrate filtration plant, a Drytech flash dryer, a modified Elkem / Hatch 13.5 MVA circular furnace, two 10? x 15? Peirce-Smith converters, and a matte granulation plant. The Zimplats smelter uses a three-field electrostatic precipitator, supplied by ELB-Brandt, for removal of particulates in the gas streams from both the converter and furnace. Construction of the smelter commenced in 1995, under the BHP / Delta Gold of Australia joint venture. The furnace was lined mid-1996, and smelting operations commenced in 1997. Due to design challenges, the Elkem furnace was modified by Hatch in 1998, and the smelter had not reached full capacity when operations were suspended in 1999. Re-commissioning took place in January 2002.

Jan 1, 2006

By Q. C. Reynolds

Keywords: Pyrometallurgy, plant, photography, GIS, satellite images, Google Earth Google Earth is a piece of software able to display an interactive three-dimensional map of the world, combining aerial and satellite photography with maps, terrain, and user-generated geographical information systems (GIS). Many structural features of the planet, both natural and man-made, are of great interest to the mining and metallurgy field, and in this paper a study is made of the current state of the art of data accessible by Google Earth.

Jan 1, 2006

By J. Kempken, T. Schreiter, R. Degel, H. Schmieden

After a short summary of the historical milestones of the submerged arc furnace, the paper will highlight different applications and their specific smelting furnace requirements in the non-ferrous area. Additionally, aspects of rectangular furnace design and the features of the copper cooling system for the side wall will be emphasized. Finally a state-of-the-art design tool as well as a new invention to improve slag cleaning technology will be featured, which shows great potentials especially for the PGM and copper related industry. Keywords: submerged arc furnaces, aerro alloys, non-ferrous, copper, slag cleaning, PGM, rectangular furnace, DC technology

Jan 1, 2006

By Gerard de Vries

pipeline industry and are still growing in size. Liquid epoxy and polyurethanes are an excellent choice for whatever the aggressiveness of the substance transported and whatever the harmful outside influences, maximum protection is required. They can be used as coatings on all kind of pipelines varying from the mainline coating to the field joint coating. Compared with traditional systems like dual layer FBE and 3-layer polyolefin there are some benefits to be considered like easiness of repairs, amount of coats, application temperature and film thickness. The interior coating renders the pipe surface so much smoother that considerable savings can be realized in pump stations. Apart from the interior of the pipeline, the industry is faced with new challenges like higher operating temperatures of lines and an emphasis on product benefits in order to save money. Key words: liquid epoxy, liquid polyurethane, phenolic epoxy, pipeline, field joint coating, internal coating, corrosion control

Jan 1, 2006

By C. J. Cutler

Metallurgical accounting for toll treatment smelters pose a number of challenges. Multiple feed stockpiles have to be accounted for as part of the monthly recovery estimation. Moreover, multiple metallurgical intermediates make up part of the in-process inventory, which also influence the monthly recovery calculation. Errors propagate from the measurements of volumes, assays, moisture fractions and bulk densities in the various material types through multiple steps up to the point where the final recovery is calculated. These errors contribute non-linearly to the variance in the final recovery estimate. This paper develops the mathematical formulation for variance propagation in toll smelting operations, including the effect of in-process inventory, assuming measurement biases have been eliminated beforehand. Operational data from a Southern African copper smelter is used for a case study. The method of propagation of variance showed that uncertainties in stockpile assays were the main contributors to variance in the recovery estimate. Variance in the volume and bulk density uncertainties contributed a secondary, yet significant, proportion to the overall recovery variance. It was determined, for the given case study, that the recovery variance depended on the calculation method used and that variance propagation via the two-product formula was smaller than recovery variances calculated via the standard recovery formula. However, the probability that the two product formula will give inaccurate (versus imprecise) results is significantly more due to the practical difficulty of equiprobable sampling of tailings streams from smelter plants (which includes materials such as slags and flue dust). Recommendations are made on how to achieve a reduction in overall uncertainty for toll treatment smelters. Keywords: metallurgical accounting, copper smelters, pyrometallurgy, variance propagation, errors, precision, sampling

Jan 1, 2006

By A E. Paterson

General aluminium corrosion charts based on 1100 alloy listing product and temperature have been developed by AFSA, mainly from available sources. The categories of corrosion expectation are fairly wide. As a result the charts are more useful in indicating what is not suited as distinct from what is. The question of how to develop useful information is assessed. Having discarded improbable options one is left with the need to refine the possible. Within each alloy group corrosion potential differs. From an engineering application point of view, the corrosion resisting marine alloys, the 5xxx series show increasing corrosion as the percentage of Magnesium increases. An important issue is that as the welding filler used for 5xxx series is Mg rich (to avoid hot cracking), the filler is likely to show the weakest resistance. In addition, when subjected to fatigue loading, the preference for critical joints is to dress the joint to the level of the base material. Overheating of the weld extends the HAZ zone and weakens the material as Mg moves to the grain boundaries. Indicator chart refinement approaches suited to aluminium use in commercial transport are discussed.

Jan 1, 2006

By G. S. Harper

Noise in general and drilling noise in particular have received increasing attention within the South African mining industry during the last 10?15 years. The Mine Health and Safety Committee1, during their 2003 annual summit, established two significant milestones to be met by December 2008 and December 2013. The 2008 milestone target is that of no more than ten per cent deterioration in hearing among occupationally exposed individuals, whereas the 2013 milestone target is that of less than 110 dB sound pressure levels at any place in the workplace. While these targets relate to general noise within the mining industry, it is widely believed that the most significant source of noise contributing to noise induced hearing loss (NIHL) among the underground workforce, is that of pneumatic rock drills. Data pertaining to the noise emission level of any machine is generally reported as either a sound pressure level or a sound power level of a single machine measured under free field conditions as defined in Appendix 3 of SABS-ISO 37442. However, rock drills are seldom used in isolation and underground conditions cannot be considered as free field. A methodology for the selection of rock drills on the basis of total operating cost has been developed. However, this paper focuses on the noise elements of the generic methodology and provides a model for the prediction of the composite sound pressure level and the equivalent noise exposure levels of groups of individuals from machines, used singly and in combination in an underground environment based on the sound pressure level determined according to SABS-ISO 3744 under free field conditions. The methodology includes provision for the consideration of the effect of hearing protection devices and the use of multiple machines in combination and provides an indication of the potential costs of hearing compensation.

Jan 1, 2006

By C. van Tonder

Paper written on project work carried out in partial fulfilment of B Tech (Engineering Metallurgy) degree This investigation relates to a multi-purpose electrolytic system. Its primary purpose is to electrowin gold from high or low concentration gold cyanide solutions and/or from gold sludge, and to convert the recovered gold into a gold (alloy) electroform or electrode at the gold mine itself. These operations are carried out sequentially and in situ in the same electrolytic cell. Electrorefining of the gold recovered may also be done in the cell. The system applies to silver as well, and may be adaptable to base and platinum group metals. It could also be used in environmental applications, to remove undesirable metals present in aqueous solution at very low concentration. The work to be discussed forms part of recently filed patent applications. Subsequent and future developments of the system are briefly outlined. This paper, in part or in full, has been published by the Metallurgical Mine Managers Association (MMMA), with permission from the authors.

Jan 1, 2006

By A. Nel

The gold mining industry in South Africa stands to benefit much from the implementation of the self-directed work team concept. Its introduction implies flatter hierarchical structures, empowerment of the workforce and increased participation. Research indicates that half of the initiatives to implement self-directed work teams, however, fail, and it is therefore imperative for companies to be aware of the factors impacting on the effectiveness of self-directed work teams in order to focus on these early in the implementation phase. The objective of the study was to qualitatively determine these factors. Semi-structured interviews based on the phenomenological method were carried out. The sample included members of, and individuals involved with, self-directed work teams (N= 26) from a large gold mining company in South Africa. Results show that most respondents rated the availability of resources to do their work as the most important factor affecting their effectiveness.

Jan 1, 2006

By T. A. Ngcobo

Paper written on project work carried out in partial fulfilment of BSc Eng (Mining)degree The purpose of this report is to assess the risks faced by mines in dolomitic compartments in particular Kloof 8 shaft. The dolomites of the West Rand comprise one of South Africa?s most natural water resources, and overlie the reefs of the richest gold mines in the world. The pumping of water from the dolomitic aquifers to prevent flooding has caused the natural water table to subside, and the resulting cavities within the dolomite rock formations that overlie many gold deposits sometimes collapse, causing sinkholes. These impacts of the mining industry could worsen over time if preventative measures are not taken. This report discusses these impacts in detail, more specifically the risks to which operations in dolomitic compartments are exposed. A risk analysis was carried out to access the risks that the organization could face and it was this analysis that allowed one to examine the best methods to combat the problems. Other factors such as geological features and seismic events were also considered for the evaluation. To aid with the completion of this work various resources were utilized. A literature study was undertaken, information was gathered from various experts who specialize in dolomitic studies, evaluations were conducted and conclusions reached. The results from the project indicated that preventative measures should be implemented and correct procedures put in place to prevent any disasters.

Jan 1, 2006

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By Ishwinder Grewal, Michael Fullam

Many factors affect the overall performance of a gravity circuit beyond that of the primary gravity recovery device. It is critical to examine the gravity circuit in its entirety in order to determine the dominant operating variables that affect overall performance. Knelson has developed a mathematical model which has been used to assist in the design of gravity circuits, and in particular, in making accurate predictions of plant scale gravity recovery. More recently, inclusion of recovery by particle size class and additional data from various mine sites and research studies has made the model more robust. The model is now able to predict GRG (gravity-recoverable-gold) recoveries using various devices such as centrifugal concentrators, shaking tables, jigs and flash-flotation within the grinding circuit. The benefits derived by these recent advancements in modeling capability are two-fold; the first is as a tool to assist in circuit design and correct equipment selection and the second is as an analytical tool to help to evaluate and enhance the performance of existing gravity circuits.

Jan 1, 2006

By L. C. Stilwell

The paper will attempt to identify the threats, however obscure, that could confront the South African platinum industry. South Africa has the largest reserves of platinum group metals in the world, and is the largest producer of those metals. This situation is no different from that which existed in the gold sector fifty years ago. Since then South Africa?s share of world gold production has dwindled, and the gold mining industry has lost its dominance. Unlike gold, platinum has widespread use as an industrial commodity. Its investment value is a minor portion of its total value. It is therefore subject to different market forces. The sheer magnitude of the industry in South Africa obscures the fact that it is a wasting industry, and that South Africa exports almost all its production as a refined metal in the form of autocatalyst. Since Hotelling published his seminal work The economics of non-renewable resource in 1931,the science of mineral economics has developed exponentially. The paper will present a background of mineral economic theory and compare to this the development of the South African platinum industry. Of particular concern to a mineral exporting country is the question of mineral rent?its definition and employment. This will be the mail theme of the paper.

Jan 1, 2006

By P. K. Van Manen

Anglo Platinum's Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex. Approximately 60% of the total concentrate received is from UG2 Reef, and 40% is from Merensky Reef. The concentrate is dried in two flash dryers, and smelted in a single 168 MVA furnace. A PGM-rich nickel-copper matte is cast, crushed and transported to Rustenburg for converting. The plant was commissioned in March 2003. The wet concentrate, containing 12-18% moisture, is weighed, sampled by one of two auger samplers, and off-loaded into a concentrate shed, either directly through a grizzly into a hopper, or onto the floor. From the shed the concentrate is conveyed to 12 concrete silos. Each of the two identical flash dryers can be fed from six silos. From the flash dryers concentrate is transported pneumatically to a 3 000-ton dry concentrate storage silo. The flash dryers are rated at a nominal 66 tph of dry concentrate at 14% moisture, while the furnace can smelt 90 tph of dry concentrate. Therefore both flash dryers are required to operate when the furnace runs at design throughput. Each flash dryer consists of a hot gas generator (HGG), a disintegrator and drying column, and a section for gas/solids separation. In the HGG, gas heated up to 700° C is produced from the combustion of coal peas in a fluidized sand bed. The hot gas and wet concentrate are introduced to the disintegrator at the bottom of the drying column. The disintegrator breaks up any lumps of concentrate, and throws the concentrate up into the drying column, where it travels co-currently with the hot gas. A fan draws the hot gas from the drying column and through the gas/solids separation section, which consists of three primary cyclones, a multiclone and a high-temperature bag house. The dry concentrate reports to a 450-ton dry concentrate storage bin. A portion of dry concentrate is recycled to the wet concentrate feed in a paddle mixer, so that concentrate that is too wet does not enter the disintegrator. The drying column outlet temperature is controlled at 120° C. Coal is received by road, screened for oversize and conveyed to a 400-ton concrete silo. From here it is pneumatically conveyed to a small feed bin at each of the HGG' s. The optimization work consists of process control improvements relating to the HGG outlet temperature, to control the drying column temperature during the ramp-up of the HGG outlet temperature and bag filters. Furthermore a heat balance is used to evaluate options to increase the instantaneous drying capacity of the existing equipment. The coal consumption derived from the heat balance is compared with the actual coal consumption. The purpose of the optimization work is to achieve an operating schedule for the flash dryers such that they operate simultaneously for as short time as possible. Most of the time one flash dryer should operate, allowing maintenance to be done on the other flash dryer, while drawing down the dry concentrate stock. Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals (PGM), base metals, flash drying, fluidized bed.

Jan 1, 2006

By P. A. Lilly, W. Sarunic

In most cases, slope movement monitoring data are collected on a temporal basis and displacement or velocity is plotted against time in order to assist the engineer to make judgements about slope behaviour. Once an unusual behaviour pattern has been established, the data are then analysed to estimate when the key inflection points occur in the data, when the slope movements start to accelerate and, ultimately, when the slope is expected to collapse. The identification of these inflection points is sometimes difficult to achieve with the naked eye. This paper presents the application of a trend analysis technique, known as cusums, to assist in this process. The authors have presented a range of data from various real life examples which highlight the effectiveness of the cusums technique. A key aspect of the cusums technique is the use of a constant (K) against which data trends are assessed. This constant is best derived from slope performance data at each site, as each rock mass will behave in its own unique way. The authors have experienced slopes that have had threshold values ranging from 0.1mm/day through to 10mm/day, and therefore a conservative approach should be adopted when assessing the performance of slopes.

Jan 1, 2006