Search Documents

By T. Lindstad, J. Kaczorowski

The Boudouard reactivity of single cokes produced from selected bituminous coals and commercial cokes has been investigated in a thermo gravimetric furnace. The effect of potassium as a catalyst for this reaction was studied, as it is known to accumulate in ferromanganese furnaces. A gaseous impregnation technique using K2CO3 as the potassium source was applied to impregnate the coke samples. The reactivity experiments were designed to simulate conditions occurring in an industrial furnace, as used for production of Mn-alloys. The coke particle size varied from 3.35 to 6.63 mm, while the temperature was maintained between 800- 1100oC with a gas composition from 50 to 75% CO2 in a CO/CO2 mixture. To determine the catalytic effect of potassium, the concentration varied from a fraction of a percent up to 15%wt. The results show that single chars vary significantly in reactivity, depending on the properties of the parent coal, while commercial cokes exhibit similar reaction rates. Temperature and partial pressure of CO2 have the strongest influence on the reactivity, while the influence of gas flow rate and coke particle size were found to be negligible. The catalytic studies revealed that the relative reactivity of non-impregnated samples are preserved after the impregnation, so the least reactive coke is still the least reactive after the impregnation for the whole range of potassium loads. Also, it has been confirmed that the Boudouard reactivity reaches a plateau at potassium concentration of 4%wt.

Jan 1, 2007

By Godofredo F. Barrios

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings from as fine as 100 microns and coarser have been used. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies which allow an end user to consider urethane screen surfaces for fine screening applications. These technologies allow an end user to use the inherent advantages of urethane with regards to wear resistance while also realizing the benefits that a high oper area urethane screen surface can bring. These benefits include non blinding characteristics and feed capacities that which rival that of traditional stainless steel surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines they are used in conjunction with. There will also be a presentation of case studies of commercial installations where these technologies are utilized. These case studies are from the base metals industry therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints which must be taken into account when considering urethane screen surfaces such as temperature and chemical attacks. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By A. K. Das, S. Pathak, C. Bhanu, P. K. Tripathy

Ferroalloys are integral part of steel melting process. The purpose of using ferroalloys is three fold e.g. killing of steel, modifying the slag composition and steel alloying. Amount of ferroalloys used for alloying is subject to requirements of steel properties e.g. yield strength, ductility, formability etc. Variety of ferroalloys (some-times pure metal) is used by steel industries depending upon their techno-economic feasibility. Size, chemistry and modes of addition of ferroalloys are suitably engineered to bring in operational consistency and cost benefits. Of late, Tata Steel has tried out a few ferroalloys for the first time with interesting results to meet the specific requirements of high strength interstitial free (IF) and micro-alloyed steels. Some of these ferroalloys have been put into regular use with complete or partial replacement of ferroalloys used earlier. Size of one of the ferroalloys has also been modified without any other adverse effects. This paper summarizes requirements of ferroalloys for the steel industry with special emphasis on recent trials.

Jan 1, 2007

By J. Baklík, V. Rak, W. Kolarcík, Z. Franc

The paper deals with hydraulic transport of thin and dense slurries. Based on mathematical modelling of three-phase flow, dynamic properties of the systems for pumping of thin slurry are solved. Theoretical calculations were experimentally verified both at the testing hall and in real operation. For thin slurry (e.g. bauxite slurry), a three-chamber hydrohoist with float is used. Dense slurry (e.g. ash and water) is transported from the power plant to a deposit site by means of a three-chamber hydrohoist with sealed separator (piston).

Jan 1, 2007

By T. Tamenti

The purpose of the project was to conduct a feasibility study to determine if the current operating bottom dump trucks that haul coal should be replaced with rear dump trucks. The engineering availability of the bottom dump trucks was lower than targeted while the operating costs are the highest of all coal haulers within the Anglo Coal opencasts. To determine if it is feasible to replace the current bottom dump trucks with rear dump trucks, a production profile simulation was conducted to determine the number of rear dump trucks that would be required to meet the annual coal hauling requirements. The total capital and operating costs of these rear dump trucks were also determined using a total cost of ownership model. These were compared with the current costs of the bottom dump trucks to determine if it is financially feasible to replace the bottom dump trucks with rear dump trucks. Having considered the capital outlay that would be required to replace the bottom dump trucks with rear dump trucks as well as their respective operating costs, it was concluded that the current bottom dump trucks should be replaced with rear dump trucks. Other factors were considered in coming to this conclusion.

Jan 1, 2007

By Wayne Burmeister, Danie Benade, Louis Meyer, Hugo Joubert

What is not measured cannot be managed. This is true of most things, including a furnace lining. This paper describes a Lining Management System used for this purpose. It provides the operations staff with a management tool to predict long term lining life and acts as a process optimisation tool. It alarms and records upset furnace conditions. Outputs from the system are described as presented through a specially developed software package and interface. It includes vertical and horizontal furnace sections showing estimated isotherms through the lining as well as the furnace bath. It also shows calculated heat flux values, estimated lining wear and the freeze layer profile. A novel three-dimensional display is described which provides the operator with a big picture view of the furnace crucible profile under real time operating conditions. The powerful trending facility for analysing both measured and calculated values is discussed. The required instrumentation hardware as well as the installation thereof is described, with special reference to an electrically insulating thermocouple socket design. Finally feedback is provided on the first year?s performance of the system installed on an open ferrochrome furnace at Assmang Chrome, Machadodorp, South Africa.

Jan 1, 2007

By A. García-Gutiérrez, A. Aragón-Jerónimo, R. Salazar-Mendoza

A theoretical analysis of a two-region solid-liquid flow system in horizontal pipes is presented, which considers a stationary bed of drill cuttings as a porous medium (-region) below of a two-phase dispersed flow (-region).The method of volume averaging was applied in this study to derive a rigorous mathematical model in which each variable is precisely defined. This model includes the volume-averaged transport equations for both the two-phase dispersed flow and the porous medium regions and terms from a macroscopic forces balance. The solution of the two-region model allowed evaluation of the behaviour of pressure gradient as a function of velocity, total volume fraction of cuttings and the relationship of the height of the stationary bed and pipe diameter. The solution is based on a backward finite difference explicit scheme. The simulated physical system is a pipe of 4.135 m in horizontal length and 0.0508 m in diameter. A one-dimensional, mesh-centred grid, consisting of 100 nodes, is used. The numerical results were compared with experimental data on slurry flows and a good agreement was found. Keywords: two-phase, cuttings transport, solid-liquid flow, drilling modelling, volume averaging.

Jan 1, 2007

By C. A. Preece

Finsch Diamond Mine, part of De Beers Consolidated Mines (DBCM), is situated between Kimberley and Postmasburg in the Northern Cape, South Africa. The kimberlite pipe was discovered in 1960 and De Beers assumed full mining rights three years later. Production commenced in 1966 from an opencast mine, and the operation moved underground in 1990 by developing and implementing a new mining method of blast hole open stoping. A mechanized block cave was brought into production in 2005. While block caving was not new to DBCM, with productive caves having operated in Kimberley and Cullinan, from the outset, the Finsch caving operation was designed as the most advanced with a semi-automated ground handling system. The extraction level was laid out as a single sided herringbone system due to the very poor ground conditions on the south side of the pipe. These factors combined to create a unique environment, which necessitated a completely new approach to draw control. The required system was developed by a team consisting of DBCM personnel from head office and Finsch, GEMCOM and Sandvik-Tamrock, the equipment manufacturers. It was essential that the system could be run quickly, provide daily updates and issue calls directly to the LHDs. It was also important that the base data were obtained from the resource model, which was to be depleted on a monthly basis, thus forming a close link between mine planning and draw control. A further requirement of the system was that it would form a central database for the extraction operation where all data pertaining to delays and changes in conditions, be they production or ground condition related, could be recorded and analysed. The design brought together empirical rules and tables developed at Cullinan plus concepts from programming developed for the front cave at Koffiefontein so that the new system was based on sound practical experience. These facets were incorporated into PCBC (GEMCOM) and CMS and PCS (Sandvik-Tamrock programmes). The system has now been operational for just under a year and while modifications have had to be made, it has proved itself as a practical and reliable tool with which to manage the draw control at Finsch. The system is unforgiving and has forced the production team to focus on the specified drawpoints. Problems have been encountered but most of these have been related to re-educating a workforce, familiar with a flexible mining method, to the strict discipline required for a modern block cave.

Jan 1, 2007

By R. G. Cawthorn

The earliest authenticated scientific report of the occurrence of platinum in rocks from the Bushveld Complex appears to be by William Bettel on 10 November 1906. Thereafter, prospecting of the chromite-rich rocks for platinum proved frustrating. I suggest that the resurgence of interest shown by Dr Hans Merensky in 1924 resulted from his realization that newly panned platinum had a different grain size from that in the chromite layers and indicated a different source rock, which he located, and it became known as the Merensky Reef.

Jan 1, 2007

By R. McGregor

You wouldn't start excavating before testing core samples, so why would you approve a project plan before all factors have been identified, reviewed and addressed? Even a champion sports team made up of the best players can't produce optimal results without a well understood and agreed game plan. Could an F1 racing team produce their outstanding performance without rigorous evaluation and testing of the factors for successful performance? Why would we expect a capital works project team to be able to get it right without an understanding and an involvement in setting and implementing the overall game plan and without an understanding of all stakeholder requirements? For International Power's Hazelwood (IPRH) mine in Victoria, the challenge was development and delivery of a 40 year mine plan, ultimately involving relocation of existing mine operations into an adjacent new coal field, land acquisitions and major environmental and other approvals to allow diversion of three streams, a highway, an Over Dimension route and other infrastructure in a political and environmentally sensitive atmosphere. The lessons from International Power Hazelwood's (IPRH) experience are: ? that the clear set of project principles and guiding values ensured delivery of a robust plan; ? a robust plan can withstand significant change; and ? value management (VM) played an important role in providing assurance, to all, that the plan was sound at both the strategic and micro levels. This Hazelwood mine project included five major VM workshops. The first was a critical review process in addition to design and cost reviews. This VM workshop was used to analyse, at a high level, the preferred coal mining sequence and design concepts, together with the interaction between design elements, risks and costs. In addition to this, the workshop provided an agreed common pathway for all downstream decisions. A second VM study was conducted to ensure that the proposed plan and design for relocation of the conveying systems from the existing mine into the new field were planned for optimum achievement from a whole of life cost, time, operational and maintenance perspective, plus the logistics of continuing operations while relocating assets. A third study followed to review the Conveyor Transfer Alliance and review functional design. A fourth VM study workshop was formed at the start of Phase 2 Alliance to ensure that the best value for money was being achieved through the current design, schedule and project arrangements and that all interfaces between parties had been reviewed and responsibilities were clear and understood. Other studies are outlined later in this paper. This paper details the evaluation criteria and processes used in the project evaluation that led to the WestField Mine Development.

Jan 1, 2007

By N. K. Singh

The calculation of resource volumes for large mineral sands deposits is the process of systematically compiling all known data in order to define the volume of ore contained and its intrinsic economic value. Traditionally, this process has been highly speculative in nature, as the variability of the layer thickness, even between closely spaced, boreholes can be highly variable. The issue of horizon continuity is of critical importance in mine modelling and resource definition. Accurate volume estimates are difficult to derive from drilling data alone, as the borehole spacing of an economically viable drilling programme is often greater than the spatial frequency of the variations in profile thickness. The limitations associated with this inferential approach to resource estimation can be mitigated through the use of newly developed ground penetrating radar (GPR) methods, thereby maximizing orebody optimization by reducing contamination and orebody loss. The use of GPR in the mining industry has historically been limited to shallow, high-resolution applications, such as the location of voids in limestone or the mapping of paleo channels for alluvial gold and diamonds (Francke and Yelf, 2003). These limitations have not been technology based, but rather market based, as the vast majority of GPR systems were originally designed for civil engineering applications. A new generation of GPR technology, designed specifically for maximum penetration in sand environments, is now being developed. This technology has been trialled extensively at the Richards Bay Minerals heavy mineral sand deposit in South Africa with optimistic results. The clay base of the mineral sands has been imaged to some 120 metres. Further equipment refinements are expected to yield even deeper profiling and higher resolution. The resolution offered by this technology is unique, allowing individual depositional sequences to be imaged and modelled in three dimensions. This paper will discuss the advances in GPR technology relevant to the mineral sands industry, as well as methods to optimize and integrate GPR data into existing mine models. Also addressed will be approaches to three-dimensional modelling of high-resolution GPR data and subsequent volume estimations.

Jan 1, 2007

By J. Forwood

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the project's gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the Lenders' and Borrower's teams has facilitated a greater understanding and `ownership' of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

By Rodney Ishak, Merete Tangstad

In the HC FeMn production, better utilisation of coke and electric power is vital for reducing the production costs. The higher manganese oxides in the charge are reduced to MnO in the prereduction zone, where also the Boudouard reaction is active. These gas-solid reactions are to a large extent decisive for the total consumption of both coke and electrical power in ferromanganese production. In the present work formulas for calculating the Degree of prereduction have been developed for industrial practice. It shows that the typical Degree of prereduction is between 10-40%, but it may in good periods be as high as 60%. Statistical analysis has been done in order to find how various operational parameters influence the Degree of prereduction. A few parameters were observed to have an effect on the prereduction. Comilog ore definitely had a positiveinfluence on the prereduction, Comilog sinter and Mamatwan ore probably had a positive influence on the prereduction, all in relation to the average prereduction in the selected periods. Meanwhile, As man ore definitely, % H2O in raw materials and increasing Hd probably, had a negative influence on the prereduction. The findings for these raw materials were very much in coherence with the results of laboratory scale experiments performed, where the CO-reactivity of different ore materials was studied.

Jan 1, 2007

By J. Krzyzanowska

Paper written on project work carried out in partial fulfilment of Bachelor of Engineering-Mining Venetia Mine, an open-pit diamond mining operation in the Limpopo Province of South Africa, currently has a mixed haul truck fleet consisting of Caterpillar 785B and C; 789C; modified 793D and 793D. Even in an ideal situation these trucks have different cycle times, which causes queuing at the loading area and their different speeds cause bunching on the ramps, leading to higher overall cycle times and lower productivity. This problem was identified but the root causes of the problem were not investigated and quantified. A time and motion study on the haul trucks was thus undertaken to measure actual cycle times and compare them to ideal cycle times as well as to observe any reasons for deviations. Ideal cycle times are partly evaluated on the basis of simulation and partly from production optimization expert input. Several areas that affect production were identified and these include: haul road conditions, the control room, dispatching programme and dispatching data management, as well as truck-shovel matching. The investigation was important in establishing control parameters for haul fleet operation since time spent queuing is production time lost, which defers waste tonnes to later in the life of mine, thus decreasing the tempo at which kimberlite is exposed.

Jan 1, 2007

By J. A. Bakken, T. Magnusson, G. Sævarsdottir

This paper describes measurements of current and voltage done on submerged arc furnaces. The aim is to focus on and attempt to separate from one another the electric arc current and the current bypassing the arc through the charge. Toward this goal two measurement campaigns on AC-arcs burning on coke beds are ac-counted for. The first was done on a 150 kVA pilot furnace at SINTEF in Trondheim Norway, and the second one was done on a 48 MVA industrial furnace run by Icelandic Alloys in Iceland. The measurements were compared to simulations employing an advanced MFD arc model. The main results are that a coke bed does not necessarily behave as a linear conductor. However the warmer chemically transformed part of an operating Si-metal or FeSi furnace probably exhibits linear behaviour and passes a considerable fraction of the phase current, perhaps on some operating conditions, as much as 50%.

Jan 1, 2007

By Y. Zhen, N. Topliffe, G. Shou

The typical service life for a long distance slurry pipeline is15 to 25 years. Determination of wear rate for a pipeline could have a high economic impact on the pipeline project. Wear is a combination of chemical corrosion and mechanical abrasion. The contribution of each factor has to be determined project by project. Normally, chemical corrosion dominates the pipe wear in fine slurry pipelines. These pipelines have been designed with a velocity between 1.5 m/s and 2.5 m/s. Solids are suspended with high homogeneity across the pipeline section. Bottom wear is not much greater than the top wear and not sensitive to velocity. The wear pattern in the pipeline transporting medium coarse solids, such as milled ore and tailings, is different. Wear concentrates on the bottom of pipeline and the outer bends, and is more sensitive to flow velocity. Wear distribution along the pipelines is similar.

Jan 1, 2007

By P. J. Bhonde, R. D. Angal, R. H. Tupkary

Manganese imparts numerous beneficial mechanical properties. Hence it finds extensive application in iron, steel and non-ferrous sector. Prevalently, it is incorporated in the form of master alloys i.e. 'ferromanganese'. In India, ferromanganese is mainly the inexpensive and paramount source of availability of manganese. Various conventional and non-conventional techniques of ferromanganese production have been adopted in past and present. However, these techniques have demerits viz. high refractory, energy consumption, losses of valuables in slag and fumes. Also geographical co-ordinates of the plant restricted the manufacturer to prefer an appropriate process. Accordingly, the industrially implemented methods had reliance on availability of infrastructure, energy, mineral resources, grade of raw material, outlay of labor, environmental compatibility of technique etc. In view of the liberalized economy and the gap scenario in the supply and demand of ferromanganese, the authors felt it indispensable to explicitly bridge up this vacuum by initially designing a simple energy conserving, eco-friendly, low capital investment technique for decarburization of ferromanganese. Measurement of the data involved studying the impact of rate governing parameters on the process kinetics. This laboratory scale investigation is expected to escalate the Mn/C quotient of high carbon ferromanganese. Key Words: ferromanganese, carbon, carbide, decarburization, rate, kinetic

Jan 1, 2007

By E. H. Myrhaug, K. Aasly, T. Malvik

Quartz is one of the main raw materials for the carbothermic production of ferrosilicon and silicon metal. The ideal process is written: SiO2 + 2C = Si + 2CO The real process is much more complicated, depending on the quality of the raw materials. Several research projects have been carried out on quartz for the (Fe)Si process during the last 50-60 years. One of the important properties that have been discussed in this review is the volume expansion that takes place between 850 °C to 1000 ºC and explosive disintegration for some quartz types. No final and definite conclusions have been made but several reasons have been mentioned: The influence of the phase transformation to tridymite, which takes place within the same temperature interval, has been discussed in several papers. Alkali impurities have been mentioned as a critical factor for this transformation to take place. Other researchers have mentioned mica impurities as a critical factor for the behavior of the quartz at these temperatures. Studies of fluid inclusions in quartz was reported in some papers focusing on the volume expansion of these during heating as a source of explosive disintegration, especially along planes of healed micro fractures that often contain vast numbers of such inclusions. Several methods for investigations of the important properties of quartz have been presented and these provide a good basis for the further research on quartz raw materials.

Jan 1, 2007

By C. M. G. Wortley, N. Randolph, I. Ralston, R. D. Beck

The ?AMIRA Metal Accounting Project? had its origin in a workshop held in Cape Town on 1 August 2001, with the title ?Challenges in Metal Accounting and Information Management?, which was organised by the Western Cape Branch of the South African Institute of Mining and Metallurgy. This workshop identified the lack of an accepted set of standard procedures for metallurgical accounting as an industry-wide problem. Discussions which followed this workshop led to the initiation of the AMIRA Project P754, ?Improving Metal Accounting?, in 2003. The primary objective of the project was to provide tools for improving the auditability and transparency of metal accounting from mine to product and to facilitate good corporate governance. The planned deliverables of the project were a series of research projects into aspects of metal balancing in different types of metallurgical operations, a Code of Practice on Metal Accounting, and a textbook on the subject which could serve as a guide for metal accounting practitioners and students studying the topic. An additional planned deliverable was the provision of a new variety of professional experts in metal accounting, through successful completion of the research projects. Researchers were engaged at the Universities of Cape Town, Queensland and Stellenbosch and the project was sponsored by five mining companies, including three of the largest global mining groups. Research Program Eight research projects were undertaken as part of the P754 project and these are described briefly here to indicate the scope of the project. University of Cape Town ?Development of a methodology for measurement network design for metallurgical accounting at Namakwa Sands?. This project was based on the Namakwa Sands Separation Plant, with a data rich environment, and involved the investigation of measurement network design through the use of heuristics and the analysis of complex processing circuits. An industry-wide survey of current practice to facilitate the development of an expert system for plant accounting measurements was carried out. ?Metallurgical accounting design at the Waterval UG-2 Concentrator?. The objective of this project is to develop a model for predicting metal recoveries from the different components of a blended ore feed to a plant. ?Optimal measurement network design for metallurgical accounting at Zincor?. This project provided a hydrometallurgical test case for the design and evaluation of a semi-automated optimal measurement network. University of Queensland ?Quantifying the relationship between mine and mill?. This project involved a case study at North Parkes Mine, in which copper and gold ore is tracked from the pit source to the product, as well as a stockpile modelling study. University of Stellenbosch

Jan 1, 2007

By L. Forsbacka, M. Nakamoto, L. Holappa

Viscosity of the slag is one of the central parameters when producing FeCr in submerged arc furnaces. It contributes to smelting behaviour and reduction kinetics of chromite ore as well as to the Cr recovery by influencing the separation of dispersed metal droplets from the slag. A typical FeCr process slag contains 5-10pct chromium oxides, CrO and CrO1.5. The neural network computation was applied to the evaluation of viscosity for slags containing chromium oxides, and the prediction of viscosity in FeCr process slag was conducted. The main results in this estimation were that the chromium oxides in FeCr process slag lower its viscosity, and that the effect of CrO on the viscosity decrease is greater than that of CrO1.5.

Jan 1, 2007