Search Documents

By J. P. Hoffman, A. S. M. de Jesus

Additions of boron have been found to increase the hot workability of stainless steels. Boron forms complex chromium-iron borides, primarily at grain boundaries but also on delta-ferite stringers. This paper describes how a nuclear technique based on the track-etch method was used to distinguish between borides and chromium carbides on grain boundaries and to investigate the distribution of boron in stainless steels. The method was found to be sensitive for boron, and made it possible for boron precipitates to be identified on grain boundaries and interphase boundaries.

Jan 1, 1989

By L. A. Vermeulen, D. D. Howat

Extensive work was done previously on the wear of grinding media and on the comminution processes operative in bal milling based on the determination of the number-size and mass-size distributions of samples of balls taken from bal mils by a specially designed device. Proof that a sample is as nearly representative as possible of the whole mass of material from which it is drawn is usually extremely difficult. This paper reports a special case in which a direct comparison was made between the number-size and mass-size distributions obtained from a sample drawn from a mil and those from the whole bal charge emptied from the mil. Exposure of the internal defects of the grinding balls caused them to develop irregular shapes after wear had reduced their diameters by about 50 per cent. As a result of the marked change in the morphology of the grinding components, an anomaly was observed between the proportion of small components collected by the sampler and that determined in the total charge. Except for this anomaly, a marked similarity was found in the data relating to the larger components in the sample and the total charge, indicating that the sample obtained by the procedure outlined is representative of the mass of the grinding charge in a mill.

Jan 1, 1989

By A. Singh, R. R. Maclachlan

SYNOPSIS A back-analysis procedure based upon 35 mm photography was developed on a laboratory scale for the pur¬pose of determining the percentage of oversize particles known to be present in heaps of fragmented rock. Eight simple blends of crushed stone containing varying percentages of oversize on a 1:40 modelled scale were examined. Simulated test conditions for the following were subjected to the photographic study: (1) a bench heap, (2) the surface exposure of a partially excavated heap, (3) a gravity-sorted surface as occurs on an apron dump, and (4) four quadrant views of an incrementally built conical heap of rock fragments. The best back-analysis determinations were obtained from (4), the cone, over all eight blends of fragments. The mean error was within -0,16 per cent of the true value, with a range of ± 1,872. This was for oversize contents of 5 to 20 per cent where a minimum 25 per cent of the photograph area was processed by digitizer. The worst results were from the apron dump at - 1,462 per cent for a mean error of ± 4,174 per cent. The intermediate results were from the undisturbed bench at -0,186 per cent with a mean error of ±2,862 per cent.

Jan 1, 1989

By N. C. Joughin, H. Wagner

Research is a business activity, and is as different from other business activities as banking is from mining. attempting to use research to solve their problems, managers do not always recognize its unique features, are frequently disillusioned with the outcome. With a view to enabling managers to use research more effectively, an outline is given of the features of research as applied to mining. Types of research are distinguished, and stages in the research-and-development process are identified. The time-scales and resource requirements of the various types and phases of research are explained. Examples of research that have reached implementation in gold mining are given to illustrate the features mentioned. Practical and economic considerations are discussed, and pitfals and recommendations in the use of research are highlighted.

Jan 1, 1989

Mr K.R. Beard was born on 19th December, 1958. He attended Marist Brothers College, Observatory, and Marist Brothers College, Linmeyer. He was awarded a bursary by SEIFSA (Steel and Engineering Industries Federation of South Africa) and gained the degree of B.Sc. Eng. metallurgy at the University of the Witwatersrand in 1982. He is a member of the Engineers' Society of South Africa. Mr G.A. Brown was born on 27th June, 1934, and matriculated at St John's College. He obtained the degrees of RSc. Eng. (Met.) at the University of the Witwatersrand in 1957, and M. Met. at Sheffield University in 1959. He is a member of the Institution of Mining and Metallurgy (UK) and the Society of Mining Engineers (USA). Or LA. Cramer was born in the USA and, having received a B.Sc. degree in metallurgical engineering from the Colorado School of Mines, he emigrated to South Africa in 1971. He enrolled as a graduate student at the University of Natal and successfully completed both an M.Sc. and a Ph.D. degree in chemical engineering.

Jan 1, 1989

The South African Institute for Mining and Metallurgy celebrated its 95th anniversary with a banquet at The Carlton on Friday, 2nd June, 1989. This event was attended by 600 people, including the Presidents of AS&TS, constituent societies, and other kindred bodies, together with members and their guests. The guest speaker was Mr Muray Hofmeyr, Chairman of the Johannesburg Consolidated Investment Company Limited, who gave an interesting and thought-provoking talk entitled 'Will we still be the best in the year 2001'

Jan 1, 1989

By C. L. Workman-Davies

Noise is a form of pollution arising mainly from the activities of man. One such activity is mining, in which man, as in many of his other activities, uses machinery of various kinds to achieve safe, healthy, and economic production. Trackless mining makes use of an advanced state of technology over that required In traditional mining methods. One of the advantages of the former, as distinct from any disadvantages it may have, is a reduction in noise levels, the number of people exposed to noise, and the duration of their exposure to noise. This paper briefly examines why noise is a problem and what various countries are doing about it in terms of standards, codes of practice, and regulations. It also investigates the extent to which noise is a problem in mining and how trackless mining alleviates this problem. The question is then posed as to whether South Africa is not setting too high a standard at this stage of its national development by comparison with what is being done by other, more-advanced countries.

Jan 1, 1989

Historical Background. South Africa's industrial history began with the discovery of gold and diamonds during the last century, and the mining industry was the first chief component of our technological development. During the past six decades, quantum leaps were made in other fields, too, when other industries and research bodies such as Escom, NDC, Iscor, Sasol, Foskor, Alusaf, Mintek, cs I R, SA B S, and A E C were established. These meaningful additions have two outstanding characteristics. Firstly, they were linked mainly to primary activities such as energy and minerals and, secondly, their establishment was to a large extent due to the driving force of individuals such as Van der Bijl, Van Eck, Rossouw, Schonland, and Roux, rather than to impersonal government policy. Encouraging signs of the evolution of such policy has emerged during the past few years.

Jan 1, 1989

By S. W. Evans, G. Pienaar

Weldable steel plate with a good combination of strength and toughness is currently produced from 0,12 to 0,28 per cent carbon low-alloy steel heat-treated by roller quenching and tempering. Alternatively, steel plate of the same strength can be produced at a lower production cost by the use of very-low-carbon steel (0,03 to 0,08 per cent carbon) processed by in-line quenching without tempering. This paper reports the results of experimental work on these steels, and compares them with the properties of conventional steel. On thinner sections, it was found that the properties of the experimental steels compare favourably with those of conventional grades.

Jan 1, 1989

By M. U. Ozbay

The stability of pillars is analysed on the assumption that pillars shed load in a stable manner if the slope the strata load-deformation relation is steeper than that of pillars in the post-peak regime. Concepts of local stiffness, mine structural stiffness, and critical stiffness are discussed. Procedures are described for the determination of strata stiffness for various pillar layouts by use of the available boundary-element computer programs. The postpeak stiffness of pillars is assessed from the available data relating to the post-peak load-deformation relationship and width-to-height ratio. Stability analyses are carried out by the contrasting of strata stiffness with post-peak pillar stiffness. It is shown that the strata stiffness becomes unacceptably small for a stable yield-pillar layout when the span exceeds about 5 times the depth. The strata stiffness is found to increase, thereby increasing the stability, as the span-to-depth ratio, number of pillars, and percentage extraction are decreased. It is also found that the stability in a yield pillar becomes difficult to achieve when al the pillars in a layout are in the descending part their post-peak load-deformation curve

Jan 1, 1989

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

COUNCIL FOR 1988/89 President C.E. Fivaz President-elect Dr O.K.H. Steffen Senior H.G. Mosenthal Vice Presidents Junior R.D. Beck Immediate Past President B.C. Alberts Honorary Treasurer Dr H. Wagner

Jan 1, 1989

Professor H.R. Philips was born in South Wales. After graduating with a B.Sc. degree in electrical engineering from the University of Bristol, he joined the National Coal Board's management training programme. Mr B. Moore was born in Coventry, England. He matriculated at Bablake School and then atended Birmingham University, obtaining a B.Sc. Mining Engineering degree in 1953. Professor J .S.J. (J annie) van Deventer matriculated at Swelendam High School. He studied chemical engineering at the University of Stelenbosch, and obtained the degrees of Hons. B. Ing. in 1978 and Ph.D. (Ing.) in 1985. Professor M.D. Brayshaw received most of his education in England but obtained his Ph.D. (Eng.) at the University of Natal. Rock fragmentation by blasting The Third International Symposium of Rock Fragmentation by Blasting will be held in Brisbane, Australia, from 26th to 31st August, 1990. The Third International Symposium of Rock Fragmentation by Blasting is designed to inform delegates on the state of the art in explosives and blasting technology, and to build on the standards of excellence set by the previous symposia in Lulea, Sweden (1983) and Keystone, Colorado (1987). Delegates with an operational, technical, or research focus on blasting will gain from this interactive symposium. Recent journal Mineral resources engineering, edited by C. T. Shaw, T.L. Car, and M. Karmis. London, Taylor & Francis, 1989. Published quarterly. US $107 per year. Risk management The Cost Engineering Association of Southern Africa (CEASA) is to hold its 3rd Biennial Symposium at Indaba, Midrand, on 25th and 26th January 1990. The title of the Symposium is Risk Management in Promotion of Capital Projects. The present political and economic environment in South Africa is characterized by a lack of financial resources, and of technical and management skills, on the part of project owners, designers, and contractors/ vendors.

Jan 1, 1989

By J. le Grange, M. Tullmin, A. Strauss, F. P. A. Robinson, C. A. O. Henning

An experimental feritic stainless steel with a chromium content of 40 per cent was welded by laser and electron beam (EB) welding processes. These techniques were found to be particularly suited to the welding of this alloy in that the impact toughness of the weld metal and heat-affected zone (HAZ) of the laser welds compared favourably with those of the parent aloy. When the EB process was used, the impact toughness of the weld metal was over 180 J/cm2. Grain growth in the HAZ was minimal for welding with these two processes. Corosion tests, conducted in a solution consisting of 20 per cent sulphuric acid and 100 p.p.m. of potassium thiocyanate, and In a highly corrosive industrial solution, indicated that the laser and EB welds were free of sensitization effects, thus confirming the metalographic results.

Jan 1, 1989

By J. J. Schoeman

In South Africa and in the rest of the world, the two mica minerals that have the most important commercial value are muscovite and vermiculite. Muscovite has been making a comparatively small but steady contribution to South Africa's mineral exports since about 1960. Vermiculite mining and concentration were started by the late Or Hans Merensky at Phalaborwa during 1946. Vermiculite has enjoyed good overseas sales since then, and during the past four years has become an important earner of foreign currency for South Africa. The various aspects of the micas that could be of general interest are briefly reviewed, such as the history of their exploitation, their mineralogy and chemistry, and their mining, concentration, production, sales, and future

Jan 1, 1989

By J. C. David, G. Coetzer

The effect of varying aliphatic, olefinic, and aromatic groups in the N- and S-positions of dithiocarbamates was investigated in the selective and bulk flotation of a mixed copper-lead-zinc-iron ore. Selective and bulk flotation were found to be dependent on the type of functional group, as well as on the position of substitution.

Jan 1, 1989

By H. A. D. Kirsten

The effects of the mining of deep-level tabular reefs are usually evaluated by use of continuum, elastic mining simulation analyses. This paper gives the results obtained from a series of analyses in which stopes of limited span are considered to be excavated in a non-linearly non-elastic, jointed and fractured rockmass. In particular, the theoretical influence of soft backfill in these conditions is evaluated. It is shown that the stress distribution and behaviour of the rockmass, alternately taken as an intact-elastic and as a fractured non-elastic medium, are completely different. The relevance of the energy-release rate commonly calculated in mining-simulation analyses, and the efficacy of its correlation with seismicity and the associated rockbursts, are reviewed. In deep-level mining operations, it is not practically feasible to obviate releases of seismic energy. The fact of their occurrence should therefore be accepted and, rather than considering the reduction of energy release as the primary objective, efforts should be concentrated on minimizing the effects of such release. Analytical results are given to demonstrate that this approach is not only correct, but also the only feasible solution to the rockburst-seismicity problem in deep mines.

Jan 1, 1989

By R. P. H. Willis

This paper describes the economics of backfilling, hydro-power, and mechanization when they are combined in an integrated stoping system. These three technologies have been shown to be viable, and the mines of the Gold Fields Group are introducing backfilling where the depths exceed approximately 2000 m below surface and in other highly stressed areas. addition, a number of mines are installing hydro-powered systems, and the first trackless stope within the Group may soon be a reality. The main emphasis in the paper is placed on the quantifiable effects of trackless stoping, including a basic risk analysis by use of a spreadsheet model. It is concluded that a substantial decrease in working costs and an increase in revenue are possible, resulting in a marked increase in working profit.

Jan 1, 1989

This paper considers the probability of the occurrence of potential rockfals in deep-level gold mines where there is point support (props, pipesticks, and timber sticks). The investigation described gave rise to the following implications: natural joints subparalel to the direction of strike have a controlling influence on the potential occurrence of rockfals; with discrete types of support such as props at typical sparings, there is a significant probability of the occurence of potential rockfals; the use of headboards oriented in the direction of strike reduces the probability; and loss of support from a prop increases the probability.

Jan 1, 1989

Mr D. Wilson was born in Vereeniging, where he also completed his schooling, matriculating from General Smuts High School in 1977. Mr K.A. van Gessel was born in 1937. His final studies were conducted at Delft University, where he graduated with an M.Sc. degree in mining engineering. Mr J.G. McCaUum was born in 1938 and matriculated at Jeppe Boys' High School, Johannesburg. Mr H. Scot RusseU started his mining career at Randfontein Estates Gold Mining Co. Witwatersrand, Limited, where he served as temporary Geological Assistant, Sampler, Surveyor, Shift Boss, and Mine Overseer. Mr A.M.P. Henderson was born in 1950, in Kiel, West Germany. Mr J.L. Nel matriculated in 1957. This was folowed by his atainment ofthe folowing degrees: B.Sc. (Chemistry, Physics) in 1961, B.Sc. Hons. (Metalurgy) in 1965, M.Sc. (Metalurgy) in 1967, and MDD (student of the year) in 1981

Jan 1, 1989