Search Documents

By M. Reuter, C. Schuffeneger, T. Seppälä, L. Holappa

Reaction kinetics of solid-state reduction of chromite pellets (laboratory made and industrial) and lumpy ore was investigated by the thermogravimetric analysis (TGA) technique. Carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at both rising temperature and constant temperature in the range of 1450 - 1550°C. Scanning electron microscopy was employed to observe and analyse the structure and composition changes of the chromite samples. For the lab-made chromite pellets, the effects of particle size and bentonite addition on the reduction behaviour were studied. The pellet with smaller particle size gave a higher reduction rate. Bentonite addition had slightly negative effect on the reduction rate. When reducing industrial pellets, temperature and CO flow rate had positive influence on the reduction rate. Reduction of lumpy ore took place slower than reduction of a pellet. In all samples, chromite reduction proceeded longer in the outer part of the sample than in the centre part. The porosity of the chromite samples was determined before and after the experiments. The porosity of lumpy chromite increased significantly during the reduction. However, the porosity of lab-made chromite pellet decreases due to sintering effect. The reaction mechanism is discussed on the basis of experimental results and earlier investigations.

Jan 1, 2004

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm)vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599 m3/s to 0.01081 m3/s. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase hold-up was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold-up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase hold-up was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold-up with the dimensionless axial distance and the gas injection rate was correlated by using the modified Froude number. The experimental values of the dispersed phase hold-up were found to be in reasonable agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004

By Q. G. Reynolds

DC arc furnaces are widely used for steel scrap melting, and are increasingly being used for smelting applications as well. The electrical resistivity of slags varies widely, from highly conductive slags in ilmenite smelting, to highly resistive slags in applications such as cobalt recovery from non-ferrous slags, and nickel laterite smelting. Models have been developed to predict the electrical behaviour of the DC open plasma arc and the molten slag bath. These models allow the voltage and current ranges of furnace power supplies to be specified.

Jan 1, 2004

By P. Fredriksson, S. Seetharaman

In the ladle refining process, the ?FeO?-content of the ladle slag is of great importance in the chemistry as well as the energetics of the process. An optimization of the process requires an accurate knowledge of the thermodynamic activities of ?FeO? in the ladle slags. Due to the discrepancies in the existing data, renewed attempts are being made at the Royal Institute of Technology to generate reliable data for binary, ternary and multi component slags containing ?FeO? at steelmaking temperatures. In order to measure the activities of ?FeO? in the slags, a gas equilibration technique was employed in the present work. The slags, kept in Pt-crucibles, were equilibrated with a CO-CO2-Ar gas mixture and quenched after equilibration. The chemical composition of the slag was analyszed. From a knowledge of the thermodynamics of Fe-Pt system, the ?FeO? activities in the slag could be evaluated. The results of the present studies, together with other literature values, were optimized in the slag software, THERMOSLAG® developed in the Royal Institute of Technology, Sweden. The results of the optimization are presented. Model calculations were performed with the KTH slag software, THERMOSLAG®, by using plant data from OVAKO Steel, Hofors, Sweden. It was found that oxygen estimations in the metal from the ?FeO? analyses of slags, obtained by conventional sampling and analysis methods, where less reliable. Estimation of the oxygen levels utilizing the sulphur partition between the slag and the metal were carried out using the THERMOSLAG® software. Reasonable estimations of the oxygen contents in the metal confirmed that this could be a very useful tool for the plant operator. Keywords: ladle, thermodynamics, slags, ?FeO?, experimentation, modelling, sulphur partition

Jan 1, 2004

[Ferro Alloys Producers Association The South Africa Institute of Mining and Metallurgy www.saimm.co.za Mintek www.mintek.co.za Eskom www.eskom.co.za ]

Jan 1, 2004

By M. H. Farjadi, J. Azari

Cost analysis of chrome ore reduction is one of the important issues facing ferrochrome producers in today?s competitive environment. Much of this depends on quality and various ratios in the actual ore. The latter can have a direct bearing on electricity consumption and optimum efficiency of the furnaces. While the industry has been successful in reducing costs by designing larger and more efficient furnaces, the role of the optimum blend of ore has perhaps been given less emphasis. This paper will discuss the general specification and metallurgical characteristics of various chrome ores for producing high carbon ferrochromium on industrial scale. By analysing the results obtained from smelting, including chromium recovery and energy consumption, the determining parameters in total cost of ferrochromium i.e. chrome ore; reductant and energy consumption can be optimized. Our study is based on actual experiences obtained from Faryab Ferroalloy Plant over a period of approximately three years.

Jan 1, 2004

By J. Daavittila

In the latter part of the 1980s Outokumpu Chrome in Tornio, Finland, was in a situation when its twenty-year-old ferrochrome plant was becoming too inefficient to sustain economically sound production. The company made extensive studies on the then available processing methods to find out the best possible processing route. As a result, the whole plant was practically rebuilt and expanded. When equipment was proven in practical operation, an application for FeMn production was developed. Now as the Tornio FeCr-plant is considering expansion, the same type of exercise is to be performed with today?s challenges, which will be discussed in the paper. These challenges include increasing costs or decreasing quality of raw materials, increasing energy costs, stricter environmental regulations and demand for better working conditions. The possibilities of resolving to these challenges will be discussed in the paper. The future and continuing development with FeCr includes the better utilization of process dusts and a lower consumption of energy. By adapting the latest automation tools to better control the process, even higher efficiencies can be achieved with present technology. New processes are considered for development in the future and some possible technologies will be described.

Jan 1, 2004

By J. von Schéele

OXYFINESTM is an oxyfuel-based concept for in-plant recycling. It enables the possibility of fines, dust, sludge (without any drying step) and other by-products generated by the steel- and metal-producing industries to be recycled directly back into existing processes or a separate on-site unit. The results from a full-scale installation (20 000 t/a) and pilot-scale trials with dry and wet materials in the steel and ferroalloy industries are presented. The latter include materials arising from ferrosilicon, ferrochrome and silicon manganese production. The concept not only provides a solution to the problems associated with dust and sludge generated in metal production, it also turns these materials into a low-cost raw material which is useful for the same production process, thus replacing some of the raw material input. If required, it could also be used, possibly as an intermediate solution, to convert the dust or sludge into an inert material with a suitable shape. Under some conditions, a directly saleable product could also be obtained. The paper reviews this technology, its status and benefits as wells as its possibilities with regard to application in ferroalloy production. Keywords: recycling, fines, dust, sludge, ferroalloys

Jan 1, 2004

By B. E. Ydstie, B. F. Lund, K. R. Løvåsen, B. A. Foss

The paper presents sensitivity analysis for a dynamic model of submerged arc silicon furnaces. The model we study, called ?Simod?, was developed by Elkem in cooperation with NTNU and Sintef. It is today a much used tool in Elkem for operator training and analysis of the dynamic behaviour of the silicon production process. The aim of our work is to bring the simulator tool closer to industrial practice, and construct a mechanism to adapt the model to the behaviour of a running process, online. The paper presents the results of the sensitivity analysis that has been undertaken for important parameters in the Simod model. The parameters associated with the process inputs are electric power loss, loss of fixed C and reactivity of carbon. The output signals that have been investigated are fed quartz, tapped silicon and silica. The paper also interprets the results of the sensitivity analysis in a process operation context.

Jan 1, 2004

By M. Shapiro, L. A. le Grange, B. Henning

Effective pyrometallurgical process vessel design requires accurate assessment of the heat fluxes through the walls of the furnace. This is particularly important for freeze lining operation which is designed to protect refractory materials exposed to chemically corrosive molten contents, or facilitate high temperature operation when the refractory materials are used at conditions close to their service limits. Numerical modelling of fluid flow and heat transfer in process vessels is often used to aid in the design of process vessels. Sophisticated models are used to analyse the three dimensional flow and heat transfer predicting the effects of electrical heating, magnetic stirring, buoyancy, shear forces, various cooling effects and ultimately heat fluxes at the walls of the furnace and refractory. Traditionally these models are applied to the separate single fluid systems in a vessel such as the freeboard region including the arc, the slag region and the metal bath. Boundary conditions such as shear forces and heat fluxes between connecting regions such as the slag and metal bath are either estimated or carried over from separate solutions. Shortcomings in these traditional approaches include the estimation of sometimes critical boundary conditions leading to unreliable heat flux calculations. Also when boundary conditions are carried over between solutions, the process is difficult to set up, time-consuming and finally not fully coupled. In this paper the definition and results of a fully integrated numerical model of a complete arc furnace are presented. The most important mechanisms acting in an arc furnace were considered, including the fields of electrical potential, current, magnetism, momentum, heat transfer and radiation. Temperature dependant properties included electrical conductivity, density, viscosity, and thermal conductivity. The geometry consists of the freeboard, the arc, slag, metal baths and different refractory regions. Although the combined model of air, slag and metal would be defined as a multi-phase problem it is not solved as such. Instead the different fluids are separated by sets of special solid baffles. These baffles allow the implicit transfer of current, magnetism, heat transfer and shear forces between the different fluids and disallow mixing of the separate fluids. The strengths of the integrated model are threefold: Firstly, it provides robustness in defining the geometry and boundary conditions for the overall model. Secondly, it provides the capability to switch on and off individual mechanisms such as buoyancy, magnetic stirring and shear forces in order to observe their individual importance. Finally, it provides a useful tool in the design process through its ability to obtain results of parameter changes in short time scales.

Jan 1, 2004

By J. Nell

An overview is given of the matte melting process used for the beneficiation of South African platinum group metal (PGM) ores. Most producers use six-electrode furnaces to melt the concentrate and Pierce Smith converters to oxidize excess iron sulphide from the furnace matte. Concentrates from two reef types (the so-called Merensky and UG-2 reefs) dominate the feedstock supply. Concentrate from the Merensky Reef is low in chromium and does not pose significant melting problems. Concentrates from the UG-2reef contain much higher levels of chromium, which results in the formation of chromium-rich spinels during melting. This is attributed to the low solubility of chromium in furnace slag under typical operating conditions (an oxygen partial pressure of 10-8?10-9bar at temperatures of 1550°C to 1600°C). During the converting process, care is needed to avoid excessively oxidizing conditions, which result in cobalt, nickel and copper losses to the slag. High nickel losses result in the formation of Fe2NiO4 (trevorite), which often forms solid solutions with FeCr2O4and Fe3O4. In future, the main challenge in the processing of South African PGM ores will be to cope with ever-increasing levels of chromium in the concentrate. A short-term solution to the problem would be to melt the concentrate under slightly reducing conditions to promote the formation of CrO, which is more soluble in the slag than Cr2O3.A longer-term solution to the problem would be to abandon the current matte-smelting process in favour of an alloy-based process, which would offer total flexibility with respect to the amount of chromium that can be tolerated in the feed. Keywords: Merensky, UG-2, furnace, slag, matte, converting, spinel, chromium

Jan 1, 2004

By B. Erdem

This article introduces a computer model, which emphasizes panel design for draglines deployed in direct side-casting mode. The study covers flat and inclined coal-seam conditions with the dragline operating along the strike-line. Two casting methods are embedded in the model: material is placed in the open set adjacent to the one on which the dragline is located (the DNS method) and material is placed in the open set adjacent to the one the dragline excavates (the DND method). While in the first method the unproductive walking time is reduced as the set is enlarged, in the second method the cycle time is lessened as the dragline swings along an acute angle. The side-casting model is shaped so as to provide several panel configurations instead of a single one to conform to the characteristics for an opencast mine. This is achieved by assigning the pit width an interval of values ranging from a minimum to a maximum. The model includes solutions to other critical design parameters such as: set length, swing angles at key cut and main cut positions, and required dragline reach at key cut and main cut positions. The model outcomes reveal the following: the stripping operation is largely affected when the coal-seam is inclined. The downhill spoiling mode should be applied wherever possible. The DNS pattern allows wider pit width intervals as well as longer sets and longer reaches.

Jan 1, 2004

By A. D. Pelton, Y. -B. Kang, S. A. Decterov

Computerized thermodynamic databases for solid and liquid metal, slag and solid oxide phases in the Al2O3-CaO-CoO-CrO-Cr2O3-FeO-Fe2O3-MgO-MnO-NiO-SiO2-S system have been developed by critical evaluation/optimization of all available phase equilibrium and thermodynamic data. The databases contain parameters of models specifically developed for molten slags, liquid steel and solid oxide solutions such as spinels, pyroxenes, olivine, monoxide (wustite, periclase, lime), corundum, etc. By means of the optimization process, model parameters are found which reproduce all thermodynamic and phase equilibrium data within experimental error limits. Furthermore, the models permit extrapolation into regions of temperature and composition where data are not available. The databases are automatically accessed by user-friendly software that calculates complex equilibria involving simultaneously slag, metal, refractories and gases, for systems with many components, over wide ranges of temperature, oxygen potential and pressure. A short review of the available databases is presented. The critical evaluation/optimization procedure is outlined using the Al2O3-CaO-FeO-Fe2O3-SiO2and Al2O3-CaO-MnO-SiO2systemsas examples. Several applications of the databases to deoxidation of iron and to inclusion control in steel are discussed. Keywords: thermodynamics, phase equilibrium, phase diagrams, databases, ferrous metallurgy, steelmaking, inclusion control, slags, oxide systems.

Jan 1, 2004

By M. A. W. Bryson

Platinum group metals are extracted almost exclusively in South Africa from three very different zones in the Bushveld Igneous Complex, called the Plat, Merensky, and the UG-2 reefs. The Plat reef is currently being exploited only by Anglo American Platinum, whereas the Merensky reef is exploited by them, Impala Platinum, Northam, and Lonplats. The UG-2 reef, on the other hand, is also processed by these producers, but Kroondal and Barplats have operations that exclusively treat ore from this reef. At present the extraction of pgms from ores in South Africa follows the traditional route of upgrading to a concentrate in a minerals processing circuit, further upgrading to a matte in a smelter, and final upgrading and separation of the individual metals in a refinery. Thus all operations that extract pgms require a minerals processing circuit, the design and performance of which is a topic of much interest, as it is a poorly understood and not a very efficient process in relative terms, compared to the other processes. Recoveries across the minerals processing circuit of between 75 and 90% are the norm.

Jan 1, 2004

By S. Luyckx

This paper reports hardness and abrasive wear resistance test results from a wide range of WC-Co alloys, varying in cobalt content as well as WC grain size. The results show that the abrasive wear resistance increases with increasing hardness and that the rate of increase is higher for larger WC grain sizes. The increase in abrasive wear resistance was found to be parabolic up to a critical hardness value and exponential above that value. The transition from parabolic to exponential behaviour was found to occur at the same contiguity value for all grain sizes, which suggests that at that contiguity value the WC skeleton becomes continuous in all WC-Co alloys.

Jan 1, 2004

By J. Härkki, R. Hiltunen

The Akanvaara intrusion (surface area 50-55 km2) in Savukoski, Northern Finland, hosts 23 distinct monocumulate layers of small euhedral chromite crystals enclosed in a silicate matrix. These chromitite layers have been divided into four groups; UC (upper chromitite), ULC (uppermost lower chromitite) LC (lower chromitite) and LLC (lowermost lower chromitite). The driving force for investigating the Akanvaara chromites and their reduction behaviour originated from their very low MgO content and relatively low Al2O3 content, giving them a unique quality which based on thermodynamics should facilitate the reduction. Another interesting feature is the high amount of V2O3 present especially in the upper chromitite. The chromites included in this study are from the UC and ULC layers (24.9 and 22.7 per cent Cr2O3 respectively). To obtain a better understanding of the reduction behaviour of Akanvaara samples in comparison to MgO-bearing chromitites, Kemi chromite from the ferrochrome works in Tornio, Finland, was included in the study as a reference sample. The reduction experiments were isothermal in a temperature range of 1000-1400°C in CO atmosphere. Experiments were also conducted with coke addition in pellets and briquettes in CO/Ar/H2 atmospheres. The results of the reduction experiments complemented with microanalytical research indicate that the Akanvaara chromites do reduce to a higher degree than the Kemi chromite. Although the aim was to characterize the mechanisms of reduction focusing on gas-solid reactions, the nature and amount of the gangue minerals was such that a considerable amount of slag phase was formed, which affected the reduction mechanisms extensively. The structural features together with low MgO and high FeO content in both Akanvaara chromites are important factors resulting in better reducibility than in the Kemi chromite.

Jan 1, 2004

By J. -C. Tricket, W. A. Düweke, S. Kock

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological model seven further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip.. Keywords: 3D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; Seismic Micro Technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2004

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By Z. Zhang

The author recently has reviewed the publications on the slag-related research in China since the Sixth International Conference on Molten Slags, Fluxes and Salts in June, 2000. In fundamental aspects, the physical property predictions and measurements, slag-metal reactions, slag-refractory reactions have received close attention, and are briefly described here in this report. More than half of slag-related publications deal with plant investigations due to the requirement of technological improvements and environmental protection. In the present paper, the research on slags in various treatments related to clean steel production and the utilization of the waste slags is briefly reviewed.

Jan 1, 2004