Search Documents

By L. G. Marshall

This report, describing the mining method of the Dresser Trap Rock Co., Dresser, Wis., is one of a series published by the Bureau of Mines on mining methods, performance, and costs at mining operations throughout the United States. SUMMARY Dresser, in Polk County, is 3 miles south of St. Croix Falls, Wis. Company operations are about 1 mile north of the townsite. The mine has been in [peration] since 1914 and under the present ownership since 1949.

Jan 1, 1959

By Jr. Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

By H. W. Kilau

The Bureau of Mines evaluated synthetic fluorspar as a substitute for natural fluorspar flux in basic cupola ironmaking. The synthetic fluor-spars tested were prepared from waste fluosilicic acid generated during the processing of fluorapatite ore. The cupola trials showed the synthetic products to be the equivalent of natural fluorspar from an operational standpoint. However, wet scrubber sampling showed that substantial losses of volatilized fluorine occurred from the cupola during operation. The losses during synthetic fluorspar trials considerably exceeded those from natural fluorspar trials. Laboratory viscosity testing, using a high-temperature rotational viscometer, confirmed this finding and indicated that fluorspar volatility in slags is related to slag basicity. Synthetic fluorspar is accordingly recommended more for highly basic cupola operation (>1.3 basicity) than for neutral or acid operation, because of the increased potential for pollution and baghouse filter detezioration"

Jan 1, 1989

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, and control of anthracite-mine fires, it was observed that the carbon monoxide disappeared from a sealed fire area much more rapidly than could be explained on the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance: (1) That the carbon monoxide, was oxidized at temperatures below 150° C. by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C. carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By J. Mitchell Linnet

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of deposits in the Bucks Lake and Chips Creek RARE II areas in Plumas and Butte Counties, California. These areas lie along the west slope of the Sierra Nevada on opposite sides of the North Fork Feather River and encompass an area of 62,800 acres (25,400 ha). Metasedimentary and metavolcanic rocks of the Pennsylvanian Calaveras Formation are intruded by plutons of Mesozoic age. Mineral; of economic iterest are in quartz veins in metasediments close to these plutons; they are principally gold and silver with minor amounts of copper, lead, and zinc minerals. Molybdenum, copper, silver, and tungsten minerals occur in tactite along metasedimentary-granitic rock contacts. In both areas, auriferous Tertiary channel gravels have been extensively developed. Asbestos occurs in ultramafic rocks in both areas, and a limestone deposit was explored in the Chips Creek area. Gold is the principal economic mineral in the Bucks Lake RARE II area. The Shenandoah Mine (fig. 1, no. 19) contains 7,500 tons (6,800 t) of indicated and inferred subeconomic gold resources in sulfide-bearing, silicified metamorphic rocks of the Calaveras Formation (table 1). Similar rocks have yielded gold at the Edman and Megowen Mines, adjacent to the area. A high potential exists for additional lode resources in the area around the Shenandoah Mine. Callahan Mining Corporation personnel believe a multi-million ton disseminated gold deposit underlies the property.

Jan 1, 1983

By Ellisworth R. Spencer, Lynn A. Alcorn, Peter G. Kovalchik, Adam K. Smith

Noise induced hearing loss (NIHL) is the most common occupational disease among workers in the mining industry. Previous studies conducted by the National Institute for Occupational Safety and Health (NIOSH) have shown that approximately 90% of coal miners and 49% of metal/non-metal miners have a hearing impairment by age 50. The Mine Safety and Health Administration (MSHA) has determined that continuous mining machines rank first among all equipment in underground coal mining whose operators exceed 100% noise dosage. The conveying system is one of the principal noise sources on continuous mining machines, due to metal on metal impacts that occur between chain flights and the conveyor deck. A highly durable polyurethane coating has been developed for the chain flights to decrease noise generated by these impacts. A continuous mining machine retro-fitted with coated flight bars has achieved overall sound level reductions of 5-7 dB in a laboratory setting. This paper evaluates the effectiveness of this engineering noise control in reducing the noise exposure of continuous mining machine operators in an underground coal mine environment. The results show that the operator of a continuous mining machine utilizing the coated flights receives a predicted 35% reduction in total work shift noise dose.

By D. W. Frommer

Mineral dressing research was conducted by the Federal Bureau of Mines under a cooperative agreement with the St. Joseph Lead Co., on three samples of iron ore from the Pea Ridge deposit in central Missouri. The objective was to provide information on how to upgrade these submarginal ores and produce marketable concentrates. Samples were prepared from drill-hole cores of similar composition and character to produce (1) a medium-grade mixed hematite and magnetite, (2) a high-grade mixed hematite and magnetite, and (3) a high-grade magnetite. In all three ores phosphorus and sulfur constituted objectionable impurities; excessive amounts of silica were also present in the medium-grade ore.

Jan 1, 1960

By S. Don Brown

Between 1987 and 1988, the Bureau of Mines studied the mineral resources of the White River National Forest and part of the Arapaho National Forest to appraise the resources present and to determine the types of deposits, and their location, that could be mined economically if sufficient demand and metal prices existed. The study included a comprehensive literature search and a limited amount of field investigation of minerals and mining activity in and near the Forest. This report summarizes a more comprehensive minerals report on the Forests prepared by the Bureau of Mines and was written for a general audience without a background in geology or related fields. Mineral resource information indicates that in the Gore Range-the area between Tennessee Pass and Gilman may contain large base-and precious-metal deposits, and could be the focus of exploration activity in the near future. The Breckenridge mining district was found to have a moderate to high likelihood for mineral exploration and possible development of gold. Recent exploration and minor development work has occurred in several other areas: Montezuma, Kokomo-Tenmile, and Upper Blue River districts, and portions of the Sawatch Range.

Jan 1, 1990

By T. J. Lutz, G. T. Homce

A standard Ford1 4600 agricultural tractor was converted to remote control to perform ASAE/SAE field upset tests (rear rollover and side rollover). This paper discusses the engineering process to develop a remote-controlled tractor in determining the critical parameters of operation, to choosing appropriate actuators, designing the circuitry to control them, installing the actuators on the tractor, testing the system for functionality and then conducting numerous overturn tests. The system uses off-the-shelf components for simplicity, replaceability, and economic concerns. The remote control system has withstood 21 tests to date with no failures and will continue to be used for at least three more years of testing.

By F. J. Wiebel

"INTRODUCTION As a result of a general survey of the iron-ore deposits of Califor¬nia, the Bessemer was one shown to offer possibilities of developing com¬mercial ore reserves. Surveying and exploring were done at the request of Congress for an investigation of raw materials for the production of steel.A wartime steel plant has been established at Fontana, San Bernardino County, and a backlog of iron-ore reserve for the maintenance of permanent steel industry on the West Coast will be of National benefit in the postwar period.W. D. McMillan, a mining engineer the Bureau of Mines, examined the property in May 1942, and it was reexamined by D. W. Butner, also of the Bureau, in October 1943. Geophysical work was done by the Bureau in 1944, and the property was explored by diamond drilling from April to August 1944 and February to SeptemberACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, under the direction of R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

May 1, 1947

By Ivette E. Torres

Table 8 provides data for the estimated value of world export trade of all mineral commodities from 1980 through 1991. It also provides a breakdown of the total into mineral fuels and non fuel minerals. These data have been developed from UN export trade data presented in table 9. The percent distribution and growth of the value of world export by major commodity groups are presented in tables 9, 10, and 11, respectively. In terms of industrial minerals (nonmetals), data in tables 10 and 11 include crude industrial minerals only, while table 8 includes an estimate for other industrial minerals. The 1991 estimates that appeared in the 1991 issues of this publication have been revised. It is typical for this section to review the year prior to the year of review because of the unavailability of data at the time of publication. The aggregated value of export trade in mineral commodities for 1992 was not available at the time of publication. The total value of nonfuel and fuel mineral exports for 1991 was about $616 billion in current (1991) dollars. The value of mineral fuel export trade accounted for about 53 % of the total mineral export trade. In 1980, the contribution of mineral fuel to the value of mineral commodity export trade had been almost 68%. The 1991 world mineral commodity export trade represents a 5.3% decrease (table 8) from that of 1990. The largest decrease was attributed to the decrease of export trade of fuel minerals (5%). The value of non fuel mineral export trade decreased by 4 %. Because the value export trade of all commodities increased by 1.2 %, the share of mineral commodities decreased from 19.2 % to 17.9 % of the total.

Jan 1, 1994

By E. C. Lane

[This Is the ninth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the interior. The first report gave data on motor gasoline sold during the winter of 1935-36.3/ The Present report presents analytical data for 2,033 samples, representing the products of approximately 80 companies, which, as in previous surveys, include both large and small suppliers. In addition, the Pacific coast is represented by data that were average by the Pacific Coast Technical Group before 'being submitted and are published exactly as they were received. As in previous surveys, the data are divided into the three groups of samples of regular-price, premium-price, and third-grade gasolines, and each group has been averaged separately. The cumber of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, arc as follows: Regular price, 1,066 samples, 208 items, and 49 brands; premium price, 575 tamales, 154 items, and 38 brands; third-grade gasoline, 7;4 samples, 150 items, and 53 brands. The meanings of these terms as used in the surveys tar as follows: Sample: The individual supply of gasoline obtained at the filling station and analysed in the laboratory.]

Jan 1, 1940

By Paul A. Pierce

In 1984, the Bureau of Mines evaluated an area previously identified as having "probable mineral resource potential" for copper, lead, zinc, gold, or silver within the Elkhorn Wilderness, about 5 miles west of Winston, MT. The purpose of this study was to determine whether the mineralized structures at nearby mines and prospects outside of the Wilderness extend into and contribute to the anomalous zone and, if so, to expand the domestic supply of strategic and critical mineral resources for future needs by identifying and quantifying resources on public lands. Fifty-eight soil samples, 23 rock samples, and 1 stream sediment sample were collected in the Staubach Creek area. Overall sample analyses suggest the anomalous zone in the Staubach Creek drainage is possibly associated with -.mall pyritiferous quartz veins. These veins or veinlets may be part of a system of northeasterly-trending structures prevalent in this art of the Wilderness. However, there is not sufficient evidence to prove that identified resources outside of the Wilderness extend into it in the Staubach Creek drainage, or that economic base- or precious-metal deposits are likely.

Jan 1, 1987

By Robert S. Sanford, Harold C. Pierce

"At one time the Alaskan Eskimo lived in many small settlements scattered along the Arctic coast. These settlements extended as far south as Bristol Bay and several miles inland on the large rivers. When the white man established trading posts, schools, hospitals, and missions, these people gradually congregated around them in a few large villages. The natural fuel supply near many of the large villages along the Arctic coast became exhausted as a result of the abnormally large influx of people from small outlying settlements.The population of Barrow, Alaska, according to the 1940 census, is 363 persons, but since that time it has increased considerably, and later estimates place the present population between 400 and 500 persons. With the exception of 25 white persons, the entire population is comprised of Eskimos.The government maintains a school, hospital, radio station, and weather station at Barrow. In addition to the government, installations, there is a church, a privately owned trading post, and cooperative store owned by the Eskimos.For many years the Barrow Eskimos depended on driftwood and petroleum residue from Cape Simpson for their fuel supply. This fuel provided not only warmth for the Eskimo during the long cold winters but also heat for melting ice, the only source of 'water during .the winter. In recent years the sources of petroleum residue and driftwood have not been adequate to meet the demands for fuel During the winter of 1942-43 and again in 1943-44, Barrow experienced an acute shortage of fuel.The fuel problem at Barrow was brought to the attention of Governor Ernest E. Gruening, who was instrumental in getting a Bureau of Mines engineer4/ to investigate reported coal occurrences in the vicinity. Coal deposits along the Meade River and at Peard Bay were examined during the spring and fall of 1943. The Alaska Native Service shipped in mining equipment in September 1943 and commenced stripping an open-pit mine on the Meade River in June 1944. In conjunction with this work, an engineer5/ of the Bureau explored by churn drilling to determine the tonnage of- coal in the vicinity of the mine. In addition to this work, the Bureau of mines examined coal deposits in Peard Bay area and along the Kuk River south of Wainwright."

Nov 1, 1924

By Oliver Bowles

"Asbestos" is not the name of a distinct mineral species but is rather a commercial term applied to fibrous varieties of several minerals. The origin and significance of names applied to asbestos by early writers are discussed in the section devoted to sources of supply and terms employed in ancient times. VARIETIES The most useful variety of asbestos is chrysotile, a fibrous serpentine the composition of which is expressed by the formula H4Mg3Si209. Chrysotile is characterized by a strength and flexibility that permit the use of the longer fibers for spinning. The bulk of the world production of both long and short fibers, is of this variety.

Jan 1, 1935

By P. M. Johnson

A design for a laser-powered optical interferometer, using a specimen whose thermal expansion is to be measured as part of the optical system, was conceived and applied in a prototype dilatometer. The object of thin work was the development of an absolute dilatometer capable of use at elevated temperature, particularly above 1,000° C. The prototype has been operated at temperatures exceeding 1,510° C. Results obtained with this device agree within 2.5 percent with the published data for the coefficient of expansion of columbium.

Jan 1, 1968

Determine safe practices for surface mine blasting near pressurized gas, oil, and water transmission pipelines. Background Surface mine blasters regularly have to address the issue of how blasting affects transmission pipelines that run near and sometimes through their permit areas. Regulatory approaches to blasting have ranged from no regulation at all to strict limits intended to prevent cosmetic cracks in plaster interior walls of homes, but they have not directly addressed the impact of blasting on nearby pipelines. Concerned with both productivity and safety, the mining industry and its regulators have requested guidance on safe practices for mining near pipelines. The Pipeline Research Group of the American Gas Association has sponsored studies of the effects of small close-in blasts because of vibration concerns related to the installation of new pipes into existing pipeline right-of-ways. By contrast, the recent study in which the U.S. Bureau of Mines (USBM) took part is the first addressing large-scale mining blasts.

Jan 1, 1995

By W. R. Hardwick

This paper describes mining methods and practices of the Morenci Branch, Phelps Dodge Corp., Greenlee County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts in the United States. A similar program, conducted from 1928 to 1939, was generally conceded to have contributed substantially to improving the efficiency of mining operations. The morenci open-pit mine (see photograph, fig. 1) is in southeastern [zona] (fig. 2), on U.S. Highway 666 about 5 miles north of Clifton, county at of Greenlee County. The concentrator and smelter are near the mine at an altitude of about 4,400 feet. Figure 3 is a map of the mine and plant.

Jan 1, 1959

By R. H. Dickson

This paper, which describes the milling practice of the Verde Central Mines, Inc., is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. GENERAL DESCRIPTION The Verde Central concentrator is located in Walnut Gulch, about 1 mile west of Jerome, Ariz., and on the Jerome-Prescott highway. It is about 1,000 feet distant from the main shaft of the Verde Central mine and treats ore from this mine only. The mill is connected with the main shaft of the mine by a 24-inch gave railway, over which the ore is hauled in 5-cubic yard capacity, rocker, side-dump cars, by a 3-ton Brookville gasoline locomotive.

Jan 1, 1931

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961