Search Documents

By J. H. Tylczak

The Bureau of Mines studied the effect of alloy additions on abrasive wear of low-alloy steels. A dry-sand, rubber-wheel abrasion test appa-ratus using ASTM G65-Sl procedure B was used for the abrasive wear tests. Eighty-six material heat-treatment combinations were abrasion tested. Results of these tests were analyzed statistically using regression analysis to see if additions of Cr, Mn, Mo, Ni, Si, AI, Cu, and S were significant in affecting the abrasive wear rate of low-alloy steels. Regression analysis was also used to confirm hardness and C affect on the abrasive wear rate of these steels. It was found that for all the steels taken as a group, increased amounts of Mn significantly reduced the wear rate, while increased amounts of Mo and S1 increased the wear rate. Analysis also confirmed previous research done by others, that increasing hardness and amounts of C reduced the wear rate. For the hardened steels taken as a class, only increasing amounts of C and Mn reduced the wear rate, while increases in Si increased the wear rate. In the class of unhardened steels, increases in C, Mn, and S re-duced the wear rate, whereas increases in Mo increased the wear rate. The steels with the best resistance to wear were two hardened experimen-tal steels similar to AISI 1055 and AISI 107S.

Jan 1, 1986

By Arno C. Fieldner

This is the fifth of a series of annual reports4/ of technologic investigations conducted by the Bureau of Mines on the occurrence, properties, mining, preparation, and uses of coal. The research of the Bureau is carefully coordinated with the requirements of the producing and consuming industries, with a view to conservation of resources of coal in mining and use, and conservation of the health and lives of workmen employed in these industries. Such coordination is facilitated by the wide range of specialization of the several groups on engaged in studies concerning coal. Here are reported correlated studies ranging from paleobotanic analysis of the formation of coal as it occurred some millions of years ago to the effect of mechanical methods of mining on present-day employment in mines. As this is a summary of the current work of the Bureau of Mines, so the Bureau likewise has provided a condensed review of the outstanding current work of others on research and technology of coal 5/.

Jan 1, 1940

By Nunna Malakondaiah

Plant samples collected from the mined sites of Beulah, Center and Zap and the test sites of North Beulah 1, North Beulah If, South Beulahh and Center were analyzed for their nutrient concentrations. The vegetation from the mined areas generally showed lower concentrations of Na, P and Cu and failed to meet the nutritional requirements for beef cattle as defined by National Research Council (minimum requirements are: Na, 600; Cu, 4; P, 1800 µg/g dry weight). Plants from Beulah showed generally higher concentrations than from Center or Tap. Tissue concentrations of K varied significantly between sites for 5 species due to the low tissue concentrations at Center. Deficiencies are difficult to isolate as the sampling was done in mid-summer and generally during that season the tissue concentrations tend to decrease in several species. All of the plant species at the unmined sites, with the exception of western wheatgrass at Zap, had lower concentrations of P than the minimum nutritional requirements for beef cattle. Sodium concentration was low but Cu was marginal to adequate in plant species at the unmined sites. Concentrations of K, Mn and Cu in western wheatgrass were greater at Center than at Zap while the opposite was true of the concentrations of Zn, Cu and P in blue grama and Cu in green needlegrass. Amending the spoil with slack at North Beulah I decreased the concentrations of Zn, Cu and P in wheatgrasses grown on spoil from 0-2, 5-10, and 20-25 foot depths, respectively. In general, the mean tissue K+/Na+ ratios were greater in plants on slack amended spoils, primarily due to the reduced Na concentrations in the tissue. At North Beulah II test site, only wheatgrasses grown on spoil amended with slack showed significant increase in K and decrease in Na and Mn concentrations. At South Beulah test site which received 12" topsoil over graded spoil, leonardite amendment decreased P concentrations in all of the grasses as compared to control, whereas fertilizer treatment increased the same. Nutrient concentrations were lower in both fescue and needlegrass with leonardite treatment and higher with fertilizer treatment although not significantly different from control. The concentrations of Ca, Mg, Na, Fe, Cu and N in grasses grown on topsoil at Center test site were significantly higher than on slack amended spoil. Legumes grown on topsoil at Center site contained higher concentrations of P than those grown on spoil; there were no significant effects due to slack on spoil or topsoil. The data presented in this report act only as an indication of between-treatment and between-species differences in tissue composition of plants harvested in mid-summer season. With respect to the nutrients analyzed, since none were found to be toxic, the cattle can safely feed on the vegetation of these mined areas.

Jan 1, 1982

By Raymond M. Stateham

Infrared and displacement studies were made of an unsupported roof in Kaiser Steel Corp.'s York Canyon coal mine, Raton, N. Mex. Monitoring of the roof continued until the roof over the area was caved. Loose slabs in the roof, about 6 inches thick, were detected by means of associated thermal anomalies, using remote-sensing infrared instruments. Displacement measurements taken during the study indicate that roof movement was cyclic in nature; the cycles appear to have been related to the mine work cycle (work days to idle days).

Jan 1, 1974

By D. Harrington

The code of hoisting signals for use in mines hoisting from one level, as suggested in this publication, is submitted to induce consideration of this subject by representative groups of the coal-mining industry, such as the lithe Inspectors Institute of America, National Coal Association, American Mining Congress, and others, as well as to -furnish a code of signals for use in those mines operated in States that do not have regulatory hoisting codes in their mining laws, or regulations. The signal codes described in this publication apply only to mines hoisting from one level and to slope mines. Mines that hoist from more than one level are referred to Bureau of Mines Information Circular 7289 Suggested Hoisting-Signal Code For Metal Mine Shafts, which suggests signals for hoisting from various levels or stations.

Jan 1, 1944

By W. W. Odell

"It has long been recognized that coke is a more desirable fuel than bituminous coal in water-gas apparatus of present design, but still considerable headway has been made in the use of the latter fuel as a substiaute for coke. This is particularly true in the Central States where the supply of high-grade coke has been very limited and uncertain during the past few years, and where coking coals of low sulphur content were available in quan¬tities. In fact, with, the present difference in price of coal and coke, it is possible to realize a marked saving when using a coking bituminous coal as generator fuel.Difficulties have been encountered in the use of such fuel, but they have, to a large extent, been overcome. One of the chief obstacles in the use of the more general utilization of bituminous coal for water-gas manufacture, is the fact that, with normal operation, the capacity per unit of time is reduced. This of course is a serious problem for plants operat¬ing at capacity with coke fuel. However, this difficulty can, to a large extent, be remedied by a changed method of operating, and can be entirely remedied by a combination of the latter with a change in the design (or proportions) of a water-gas set. The preceding statement, the reader will understand, refers more particularly to a carburetted water-gas set.In the manufacture of water gas from coke, present practice requires that for continuous 24-hour service the heat of combustion of all the carbon monoxide (CO) generated during the air blow be utilized in addition to the sensible heat of the gas coming from the generator. This is doubly true when making carburetted water gas from bituminous coking coal. The reasons why this is so are apparent when the following factors are considered."

Nov 1, 1920

By T. C. Phalen

"Necessary Qualities There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, also, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the ele¬ments, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of ad-hearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco."

Dec 1, 1919

By Michael S. Miller

In 1986 and 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the nine separate parcels that comprise the 4,330-acre South Warner Contiguous Wilderness Study Area in order to evaluate their identified mineral resources. The nine parcels are along the east side of the South Warner Wilderness. They are, from north to south, the Granger, Milk, Cottonwood, Owl, Hornback, Eagle, Emerson, Barber, and Van Riper parcels. The Wilderness Study Area is underlain by basaltic, andesitic, and rhyolitic volcanic rocks and by sand and gravel deposits. Low-grade metamorphism is widespread in the volcanic rocks, with quartz, zeolites, datolite, chlorite, and calcite locally abundant in veins and amygdules. The rocks have been displaced by the mountain-front Surprise Valley fault and by crosscutting high-angle faults.

Jan 1, 1988

By Janet Torma-Krajewski

Job tasks that involve exposure to work-related musculoskeletal disorder (WMSD) risk factors may impact both the risk of injury and production downtime. Common WMSD risks factors associated with mining tasks include forceful exertions, awkward postures, repetitive motion, jolting and jarring, forceful gripping, contact stress, and whole body and segmental vibration. Mining environments that expose workers to temperature/humidity extremes, windy conditions, and slippery and uneven walking surfaces also contribute to injury risk. National Institute for Occupational Safety and Health (NIOSH) researchers worked with powder crew members from the Bridger Coal Company to identify and rank routine work tasks based on perceived exposure to WMSD risk factors. This article presents the process followed to identify tasks that workers believed involved the greatest exposure to risk factors and discusses risk reduction strategies. Specifically, the proposed prill truck design changes addressed cab ingress/egress, loading blast holes, and access to the upper deck of the prill truck.

Jan 1, 2009

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1962. Injury experience is measured by the number of injuries sustained per million man-hours of exposure in each industry. No attempt has been made to combine these data and present rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in volume III of the Minerals Yearbook. COAL The injury-frequency rate for the coal-mining industry of the United States increased less than 2 percent, according to reports received by the Bureau of Mines. The number of fatal and nonfatal injuries per million man-hours in 1962 was 45.86, based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1963

By Steven J. Knoll, Theodore J. Williams, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 18 and 40 m, and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

By H. W. Davis, Richard J. Lund

"In presenting the results of this survey on consumption of ferrous scrap and pig iron for the year 1935 the Bureau of Mines, responding to requests from industry, seeks to fill a major gap that has long existed in the field of metalliferous raw-material statistics. This type of information is designed to meet the needs of: (1) Consumers of ferrous scrap. including operators of blast furnaces, steel mills, ferrous foundries, and rolling mills; (2) marketers of scrap iron and steel, including large brokers who sell, and dealers who collect, prepare, and sell the material; (3) large scrap producers; (4) producers of iron ore, with which scrap competes indirectly; and (5) other individuals and agencies interested in more general economic analysis, since the scrap market has repeatedly been cited as one of the most sensitive of all industrial barometers, If the survey prover as useful as now seems probable, it will be continued annually with possibly an enlarged scope of treatment.The Bureau appreciates that its first efforts in this field may not meet all expectations: but it hopes to develop gradually, through suggestions, advice, and criticism from the industrial groups most interested, a type of analysis that will accord closely with technical processes and best meet the needs of all groups vitally interested in supplies and use of ferrous scrap. Constructive criticism and suggestions from industry regarding improvements to be desired in the conduct of future surveys on this subject will therefore be warmly received by the Bureau."

Nov 1, 1936

By A. F. Jolly

In an effort to better predict the useful service life of friction rock stabilizer mine roof bolts in coal mine environments, the Bureau of Mines has evaluated the corrosion resistance of stabilizer steels in air-saturated and deaerated waters from seven Eastern and Midwestern underground coal mines. Accelerated electrochemical corrosion tests were used to estimate corrosion rates for the two high-strength, low-alloy (HSLA) steels used to fabricate Split Set stabilizers and for galvanized steel. Long-term static-immersion weight-loss tests were also conducted with the HSLA steels. Corrosion rates developed from the weight-loss tests (steady-state air dissolution) were roughly comparable to rates determined from electro-chemical testing in aerated waters. Although the highest rates occurred in waters with the highest chloride contents, rates in the other waters were low (<2.0 mpy) and exhibited little correlation to the widely varied chloride contents of the waters. The generally low corrosion rates are attributed in part to the tendency to deposit a protective CaC03 film, reflecting susceptibility to carbonate precipitation as indicated by positive Langelier (saturation) index values for the waters. With one exception, corrosion rates for the galvanized steel were (2.0 mpy. Rates with aerated waters were higher than those with deaerated waters. Pitting tendencies of the steels were also estimated.

Jan 1, 1987

By G. R. Hopkins

The petroleum-refining industry established a. new record in fuel effieciency at refineries in 1936, when 597,000 B. t. u. of heat mere required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the &apos;indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio ( crude runs divided by capacity) for re- fineries increases toward tine maximum of 100 percent, the fuel requirements show progressively smaller increases and the average B. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By G. M. Kintz

In safety work a study of past accidents is of value in determining means of reducing future accidents of the same character. This is particularly true with reference to coal-mine explosions. Data from publications of the United States Bureau of Mines and from published reports of the State inspector of coal mines of Colorado are presented in this circular in the belief that they will be of value to operators by indicating methods of preventing future coal-mine explosions. The tables included are complete only with regard to major disasters. The Bureau of Mines considers as a major disaster one in which five &apos;or more men are killed. However, this circular also includes a considerable number of minor disasters, Various explosions in the coal mines of Colorado from 1883 to 1932, inclusive, are listed with information available as to their probable cause, number of men killed and measures which, if they had been in use at that time, might have prevented them. John McNeil, first Colorado State coal-mine inspector, on page 43 of his first report for the period ended July 31, 1884, made the following recommendations for the prevention of explosions in the coal industry: True causes could be traced either to insufficient ventilation, carelessness and lack of rigid discipline in carrying on energetic ventilation and other precautions needed to be enforced in a mine giving off explosive gases. *** When any quantity of fine coal dust is observed in an entry, air course, or room it should be made damp and be removed from the mine, and thus beep every place as free from dust as possible. *** A system of bratticing close up to the face of each and every place in the mine from crosscut last made (whether gas should just then show its presence or not) which should not be more than 50 or 75 feet according to the nature of the mine.

Jan 1, 1933

By H. L. Riley

At the Southern Experiment Station, Tuscaloosa, Ala., reports are prepared from time to time on results of washability studies of coal from important beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. The principal objective of a washability study is to obtain technically and commercially important data to aid in determining the best methods for preparing and utilizing the Nation&apos;s reserves, particularly of coking coals. Such information is also important from the standpoint of conservation, because it facilitates the selection of preparation methods that will yield an acceptable product with a minimum loss of coal to the rejects.

Jan 1, 1958

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past-several years the flow of natural bas through high--pressure pipe lines.4 This report deals with that part of the study involving the design of pipe-line, systems consisting of lines laid parallel to each other. The lines are deferred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is, connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers&apos; demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By W. D. Mcmillan

"Magnetic surveys made by the Missouri Bureau of Geology and Mines in 931 and 1932 disclosed a large positive anomaly about a mile south of Bourbon, Mo. 3/ Electrical resistivity measurements made by the Division of Geophysical Exploration of the Bureau of Mines in the winter of 1942-43 indicated that the source of this anomaly was in the pre-Cambrian rhyolite at a depth of more than 1,400 feet. 4/In order to determine the character of the material that caused the magnetic anomaly, which might be either a body of magnetite or a large intrusive of basic rock, the Bureau of Mines drilled four holes to depths of 1,800 to 2,300 feet. Magnetite in rhyolite porphyry was encountered at 1,600 to 2,000 feet, and this is doubtless the main source of the magnetic anomaly, although it is possible that additional iron ore exists at greater depth.Hole 1 was apparently located southeast of the source of the anomaly and encountered only small stringers of magnetite. Hole 2 penetrated four mineralized zones having a total thickness of 125.7 feet and an average weighted content of 43.52 percent iron and 31.62 percent silica. These zones were tested again by a deflection hole, 2A, which gave nearly identical indications. Hole 3, 500 feet north of hole 2, penetrated 58 foot of mineralized rhyolito containing an average 43.4 percent iron.Metallurgical tests showed that the silica in the ore is tightly locked with the magnetite. After grinding to minus 100 mesh, a 66 percent iron con¬centrate with 7 percent silica was obtained by flotation."

Oct 1, 1946

Develop computer software that can aid in improving the visibility and illumination in underground mines by providing quick analysis of existing equipment and conditions and the effects of potential modifications. Background Poor visibility and illumination are common problems in underground mining. Mining equipment often restricts operators&apos; fields of vision. Also, fighting systems are often positioned where they cause excessive glare, which restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines (USBM) has developed a PC-based software package to analyze certain human engineering aspects (ergonomics) of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines. Approach The Crewstation Analysis Programs (CAP) package includes assessments of visibility, illumination, and glare in the surrounding work area. The advantage of using computers for these types of analyses is that numerous design iterations can be tested quickly and efficiently to determine the effects of changes on visibility. This cuts down the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where testing would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design could be tested while the machine remained in service.

Jan 1, 1993